GIGA K2V, K4V, K4PFCE, K4VFCE, K4VFE Installation, Operating And Maintenance Instructions

016_03

Installation, operating and
maintenance instructions

09/2009

ELECTRIC COOKERS

K2V · K4V

K4PFCE · K4VFCE · K4VFE

K6PFCE

K2P · K4P · K6P

K4PFE · K6PFE

OP2P · OP4P · OP6P

OP2V · OP4V

© COPYRIGHT 2004 GIGA GRANDI CUCINE SRL

016-03 - Electric cookers

2

Models and dimensions page 3

Technical data 6

Installation instructions 7

Installation 7

Legal and technical requisites 7

Installation 7

Wiring 7

Unipotential 7

Using the appliance 7

Ignition 7

Cleaning and taking care of the

appliance 8

What to do if not using the appliance

for a long time 8

What to do if something goes wrong 8

Maintenance 8

WEEE Directive 9

Wiring diagrams 10-27

Warning 28

INDEX

016-03 - Electric cookers

3

Dimensions

K2P

400 x 900 x 875

weight approx..63 kg

K4PFE / K4PFCE

800 x 900 x 875

weight approx..138 / 122 kg

K6PFE / K6PFCE

1200 x 900 x 875

weight approx..168 / 151 kg

K4P

800 x 900 x 875

weight approx..111 kg

K6P

1200 x 900 x 875

weight approx..131 kg

016-03 - Electric cookers

4

Dimensions

K2V

weight approx.62 kg

K4V

weight approx.108 kg

K4VFE / K4VFCE

weight approx.134 / 118 kg

016-03 - Electric cookers

5

Dimensions

OP2P

weight approx.52 kg

OP4P

weight approx.96 kg

OP6P

weight approx.107 kg

OP2V

weight approx.50 kg

OP4V

weight approx.92 kg

016-03 - Electric cookers

6

The data plate is located on the rigth hand side of the
control panel and contains all the data needed for connecting
it up to the mains electricity supply.

3 - TECHNICAL DATA

CAT/KAT GAS/GAZ G30 G31 G20 G25

II2H3B/P P mbar 30 30 20 -

II2H3+ P mbar 30 37 20--

II2H3+ P mbar 28 37 20 -

0051
TIPO/TYPE

MOD.

ART.

N.

N.

Qn kW

MOD.

V AC kW Hz

THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE
AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS
BEFORE INSTALLING AND USING THE APPLIANCE.
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.

II2ELL3B/P P mbar 50 50 20 20

II2E+3+ P mbar 28 37 20 25

II2H3B/P P mbar 50 50 20 -

I2E P mbar - - 20 -

II2H3+ P mbar 28 37 20 -

I3B/P P mbar 30 30

m3/h

I3+ P mbar 28 37

Predisposto a gas: - Gas preset: - Prevu pour gaz:

Eingestelt für Gas: - Preparado para gas: -

--II2H3B/P P mbar 30 30

--

--

Geschuckt voor:

SE FI DK CZ SK SI

IT CH PT

ES IE GB GR

NL

25II2L3B/P P mbar 30 30

DE

FR BE

AT CH

LU

EE LV LT

EE LV LT

NO MT CY IS HU

CY

MADE IN ITALY

Model

K2P

K4P

K6P

K4PFCE

K4PFE

K6PFCE

K6PFE

K2V

K4V

K4VFCE

K4VFE

OP2P

OP4P

OP6P

OP2V

OP4V

Model

K2P

K4P

K6P

K4PFCE

K4PFE

K6PFCE

K6PFE

K2V

K4V

K4VFCE

K4VFE

OP2P

OP4P

OP6P

OP2V

OP4V

Version

Electric range - 2 plates on open stand

Electric range - 4 plates on open stand

Electric range - 6 plates on open stand

Electric range 4 plates - electric convection oven 1/1 GN

Electric range 4 plates - electric oven 2/1 GN

Electric range 6 plates - 1/1 GN electric convection oven - neutral unit

Electric range 6 square plates - 2/1 GN electric oven - neutral unit

Electric pyroceramic range with 2 plates - neutral unit

Electric pyroceramic range with 4 plates - neutral unit

Electric pyroceram range 4 plates - electric 1/1 GN convection oven

Electric pyroceram range 4 plates - 2/1 GN electric oven

Electric range - 2 plates

Electric range - 4 plates

Electric range - 6 plates

Electric pyroceramic range with 2 plates

Electric pyroceramic range with 4 plates

TABLE 1

Resistance (kW)

1 2.5

1.5 3.4

-

-

-

-

-

-

-

1

2

2

2

-

-

-

1

2

Plates

4 kW

Oven

2.5 kW

Oven

5.9 kW

-

-

-

-

-

-

-

-

1

2

2

2

-

-

-

1

2

2

4

6

4

4

6

6

-

-

-

-

2

4

6

-

-

-

-

-

1

-

1

-

-

-

1

-

-

-

-

-

-

Power

Voltage rating

-

-

8.0 kW

-

16.0 kW

-

24.0 kW

-

18.5 kW

1

21.9 kW

-

26.5 kW

1

29.9 kW

-

5.9 kW

-

11.8 kW

-

14.1 kW

1

17.7 kW

-

8.0 kW

-

16.0 kW

-

24.0 kW

-

5.9 kW

-

11.8 kW

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

400 V 3N or 230 V 3

Dim.: LxWxH

400 x 900 x 875

800 x 900 x 875

1200 x 900 x 875

800 x 900 x 875

800 x 900 x 875

1200 x 900 x 875

1200 x 900 x 875

400 x 900 x 875

800 x 900 x 875

800 x 900 x 875

800 x 900 x 875

400 x 900 x 270

800 x 900 x 270

1200 x 900 x 270

400 x 900 x 270

800 x 900 x 270

Lead wire / Section

5 x 2.5 mm2 or 4 x 2.5 mm

5 x 2.5 mm2 or 4 x 2.5 mm

5 x 6 mm2 or 4 x 10 mm2

5 x 4 mm

5 x 4 mm2 or 4 x 6 mm

5 x 6 mm2 or 4 x 10 mm

5 x 6 mm2 or 4 x 10 mm

5 x 2.5 mm2 or 4 x 2.5 mm

5 x 2.5 mm2 or 4 x 4 mm

5 x 2.5 mm2 or 4 x 4 mm

5 x 4 mm2 or 4 x 6 mm

5 x 2.5 mm2 or 4 x 2.5 mm

5 x 2.5 mm2 or 4 x 4 mm

5 x 6 mm2 or 4 x 10 mm

5 x 2.5 mm2 or 4 x 2.5 mm

5 x 2.5 mm2 or 4 x 4 mm

2

or 4 x 6 mm

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

016-03 - Electric cookers

7

efore beginning installation, remove all packaging from
the appliance. Some parts are protected with an adhesive
film which should be carefully removed.
Any remnants of glue should be thoroughly cleaned using
suitable substances such as benzine. Under no circum­stances should abrasive substances be used.
Fit the legs to the appliance. The appliance must be level­led using a spirit level.
Slight irregularities can be levelled by adjusting the feet
themselves.The main switch or plug should be located in
the vicinity of the appliance and easy of access.
We recommend installing the machine under a range
hood so that all the fumes are removed as quickly as pos­sible. Make sure that all fire prevention standards and sa­fety precautions are strictly adhered to.

Legal and technical requisites

When installing the appliance, the following safety stan­dards must be adhered to:

- Local accident prevention standards

- Current CEI standards.

Installation

Installation, start-up and maintenance should only be car­ried out by expert personnel.
All work required to install the appliance should be carried
out in compliance with all local standards and regulations.
The manufacturers decline all responsibility where poor
performance is due to incorrect installation in disregard of
the above conditions.

Warning!

In compliance with international regulations, when
connecting the appliance to the mains power supply, a
device with a minimum aperture of 3 mm between con­tacts must be fitted upstream of the appliance, al­lowing omnipolar disconnection of the appliance from
the mains.

Wiring

When choosing the lead wire, make sure it has the fol­lowing characteristics: it should be at least of the H07 RN­F type and its section should be large enough for the ap­pliance (see "Technical specifications and dimensions",
page 6). Two lead wires are needed for models with a vol­tage of 230 V 3 AC. The terminal boards are in the terminal
box located underneath the appliance on the left hand si­de. Pass the wire through the core hitch and wire clamp,
plug the leads into their terminals on the board and secure
them.
The earth lead must be a little longer than the others so
that it is the last lead to disconnect if the wire clamp
breaks.

Unipotential

The appliance must be connected up to a unipotential sy­stem. The connection screw is located underneath the ap­pliance on the right hand side, close to the electrical pa­nel. It is labelled.

Warning!

The manufacturers cannot be held responsible for any
damage due to inadequate or incorrect installation.
Under such circumstances the guarantee will be consi­dered null and void.

INSTALLATION INSTRUCTIONS

1

USING THE APPLIANCE

Warning!

- Beware of inexpert handling!

- Never leave the hotplates on unused!

- Only use flatbottomed pots and pans, and make sure
that the diameter of the pan is never smaller than the
diameter of the hotplate it is being used on.

Ignition

Turn on the switch upstream of the appliance.

A) Hot plates

Turn the knob corresponding to the hotplate you wish to
use, to a number between 1 and 6.
The pilot lamp will light up as soon as the appliance is on.
We advise first turning the hotplate up to maximum tem­perature. Once this has been reached, turn the knob to

the required heat To turn any hotplate off, simply turn the
knob back to "0".

6

5

4

1

2

3

016-03 - Electric cookers

8

6 to begin cooking max. 5/10 min;

5 for high temperature cooking;

4 for medium temperature cooking;

3 to continue cooking large quantities;

2 to continue cooking small quantities;

1 to keep food hot or melt butter;

0 hotplate off.

B) Oven

Turn knob (A) to the type of cooking required. Turn ther­mostat (B) to the required temperature. Pilot lamp (C) will
light up, indicating that the appliance is on.
Pilot lamp (D) will light up, indicating that the resistances
are working; as soon as the required temperature is rea­ched, it goes off.
When the resistances come on again, it lights up once mo­re. To turn the oven off, turn both knobs back to their origi­nal position.

CLEANING AND TAKING CARE OF THE
APPLIANCE

Warning!

Never clean the appliance with jets of water, whether
direct or pressurised.

Thoroughly clean the appliance every evening after use.

Daily cleaning means better performance and a longer
useful life.
Before starting to clean the appliance, disconnect from
the mains.**
Remove all the extractable parts from the oven and wash
separately. All steel parts should be washed in warm wa­ter, using a neutral detergent.
Avoid using abrasive or corrosive detergents which could
damage the steel.

What to do if not using the appliance
for a long time

Thoroughly clean and dry the machine as described.
Disconnect the power supply**.

What to do if something goes wrong

If anything goes wrong, immediately turn the appliance off,
then turn off the power supply at the switch located
upstream of the appliance, and call the aftersales depart­ment.

MAINTENANCE

All maintenance should be carried out by qualified person­nel only. Before carrying out any maintenance work, un­plug the appliance or turn off the switch upstream of the
appliance**.

NOTE**

Models with a voltage of 230 V 3 AC have 2 lead wires; re­member to cut off both power lines when disconnecting
these models; if only one or other of these leads is discon­nected the appliance will stay live.

2

D

A

0

5

0

0

1

0

5

1

2

0

0

3

0

0

2

5

0

C

B

Suola e cielo
Top and bottom
Sole et ciel
Ober- und Hunterhitze

Cielo
Top
Ciel
Nur Oberhitze

Suola
Bottom
Sole
Nur Hunterhitze

016-03 - Electric cookers

9

THE 2002/96/EC DIRECTIVE (WEEE):
information to users

This informational note is meant only for owners
of equipment marked with the symbol shown in
Fig. A on the adhesive label featuring the tech­nical specifications applied on the actual pro-

duct (the label also giving the serial number).

This symbol indicates that the product is classified, ac­cording to the regulations in force, as an item of electrical
and electronic equipment and conforms to EU Directive
2002/96/EC (WEEE) meaning that, at the end of its service
life, it must be treated separately from domestic waste,
i.e. it must be handed in free of charge to a separate wa­ste electrical and electronic equipment collection centre
or returned to the reseller when buying a new equivalent
item of equipment.

The user is responsible for delivering the unit at the end of
its life to the appropriate collection facilities. Failure to do
so shall result in the user being subject to the penalties
prescribed by the legislation in force on waste.
Suitable separated collection so that the unit no longer
used can be sent off for environmentally compatible recy­cling, treatment and disposal helps avoid possible negati­ve effects on the environment and on health and facilita­tes the recycling of the product's component materials.

For more detailed information on available collection sy­stems, contact the local waste disposal service or the
shop you purchased the unit from.
Producers and importers fulfil their responsibility for envi­ronmentally compatible recycling, treatment and disposal
both directly and by joining a collective scheme.