EN
Quick start guide
Touch panel for:
Music/Call/Volume/
Track controls
QUICK START
GUIDE
H500BT
LED indicator light
B
A
Audio jack
Micro USB
charging slot
Power On/O
Microphone
Pairing/Mute (call)
[ 1.0 Charge t he batter y ]
1. Plug one end of USB cable into the charger (or into the USB port of a computer).
2. Plug the other end of the cable into the micro USB charging slot on the headset.
3. When the headset is charging, a white indicator light will be displayed.
4. When the headset is fully charged, the white light goes o.
[ 2.0 Turnin g the headset o n and o ]
1. Turn the headset on. Press and hold for 2 sec.
2. Turn the headset o. Press and hold for 4 sec. A white indicator light turns on for 1.5 sec. and then the headset will turn o.
B
B
[ 3.0 Pair t he headset wi th your phone ]
Pair the headset with your phone manually or by using NFC. After successful pairing, the headset connects automatically to the
phone once the headset is turned on and within range.
10:30
10:31
Settings
Devices Found
Onkyo H500BT
Select
Back
Settings
Enter Password
Select
Settings
Connectivity
Bluetooth
Add
Bluetooth
device
Select
Back
‘0000’ not required for
some mobile phones
Manual Pairing
10:32
Connectivity
1. Make sure your headset is turned on.
2. Press and hold until an alternating blue and white light flashes.
****
3. Turn on the Bluetooth function on your phone.
0000
4. Your phone will start searching for Onkyo H500BT.
Back
A
5. Follow the on-screen instructions to pair your phone. (Check your phone’s user manual for
details)
NFC Pairing
1. Make sure your headset is turned on.
2. Press and hold until an alternating blue and white light flashes.
NFC
detection
area
(Left side)
Remarks:
• Make sure your mobile phone has the NFC feature and that the NFC function has been switched on and your phone is not in standby mode.
• Pairing with NFC is suitable only for Android mobile operating system 4.2 or above.
3. Make sure you turn on the NFC function on your phone and that your phone’s screen
remains active.
4. Place your phone over the headset so that the NFC detection area of each device touch each
other.
5. Follow the pairing instructions of your phone. If a passcode is required, enter ‘0000’.
A
www.onkyo.com
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under
the responsibility of Gibson Innovations Ltd., and Gibson
Innovations Ltd. is the warrantor in relation to this product.
Gibson Innovations Netherlands B.V. Building
[ 4.0 Usin g music and cal l controls ]
MUSIC CONTROLS VOICE/CALL CONTROLS
Play/Pause Tap once
Volume up
Volume down
Slide up or
slide up and hold
Slide down or
slide down and hold
Skip forward Slide forward
Skip backward
Slide backward
Siri/Google Now* Press once
Pick up call/Hang up
Tap once
Reject incoming call Tap and hold
Mute/unmute the mic
while in a call
Switch caller while
in a call
* To use the voice control feature on your phone via Bluetooth please refer to
the user manual for the correct settings for your device.
Press once
Slide forward
A
A
[ 5.0 LED I ndicator lig ht ]
A white light flashes slowly.
An alternating white and blue light flashes.
A blue light flashes at every 8 seconds interval.
A blue light flashes rapidly.
The battery is low.
The headset is in pairing mode.
The headset is both paired & connected.
The headset is switched on but not connected. If no connection
can be made, the headset will turn itself o after 5 minutes.
[ 6.0 Cor ded audio con nection ]
You can also use this headset with the audio cable provided when the battery is low. Make sure the headset is turned o before
using the audio cable.
[ 7.0 Multipoi nt ]
Pairing additional devices
A total of 4 bluetooth devices can be paired with your headphones. (See step 3 for pairing). Two devices can be connected
simultaneously allowing you to switch between them both.
Switching between devices
The multipoint feature allows you to connect and switch between two devices simultaneously. Simply pause your music or video on
one device and press play on your second device, the headphone will automatically connect to the playing device.
When you receive a phone call the audio on the first device automatically pauses to receive the phone call on the second device, with
the audio resuming when the call has finished. (See step 4 for call controls)
Please refer to www.onkyo.com/welcome for the full user manual
Loading...