Gibson Innovations E200BT User Manual
QUICK START GUIDE
E200BT
Languages x 1: EN
Box size: W95 x H150 x D25 mm
QSG size: W89 x H144 mm( Folded)
Binding: 1. Folded / 2. Glue / 3.Saddle stitch
Sleeve size: W210 x H50 mm
QSG (A1/B1) - Print color: 2 colors ( Black + PMS186c)
Revised illustration_EN (2015.07.23)
EN
Quick start guide
QUICK START
GUIDE
E200BT
On/O button,
Music/Call
control
Volume/
Track
control
Micro USB
charging slot
Microphone
[ 1.0 Charge t he batter y ]
1. Plug one end of USB cable into the charger (or into the USB port of a computer).
2. Plug the other end of the cable into the micro USB charging slot on the headset.
3. When the headset is charging, a white indicator light will be displayed.
4. When the headset is fully charged, the white light goes o.
[ 2.0 Turn on an d o the headse t ]
1. Turn the headset on. Press and hold for 2 sec.
2. Turn the headset o. Press and hold for 4 sec. A white
indicator light turns on for 1.5 sec. and then the
headset will turn o.
[ 3.0 Manu al Pairing ]
1. Make sure your headset is turned o.
2. Press and hold until an alternating blue and white
light flashes.
10:31
Back
10:32
3. Turn on the Bluetooth function on your phone.
Settings
Connectivity
4. Your phone will start searching for Onkyo E200BT.
Enter Password
****
5. Follow the on-screen instructions to pair your phone.
0000
Select
(Check your phone’s user manual for details)
Back
10:30
Settings
Connectivity
Settings
Bluetooth
Devices Found
Onkyo E200BT
Add
Bluetooth
device
Select
Select
Back
‘0000’ not required for
some mobile phones
LED
indicator
light
www.onkyo.com
2015 © Gibson Innovations Limited.
All rights reserved.
This product has been
manufactured by, and is sold under
the responsibility of Gibson
Innovations Ltd., and Gibson
Innovations Ltd. is the warrantor in
relation to this product.
Gibson Innovations Netherlands
B.V. Building
[ 4.0 Use m usic and call co ntrols ]
MUSIC CONTROLS CALL CONTROLS
Play/Pause Press once
Volume up Press once
Skip forward
Volume down Press once
Skip backward
Long Press
Long Press
Pick up call/Hang up Press once
Reject incoming call
Switch caller while
in a call
Mute/unmute the mic
while in a call
[ 5.0 LED I ndicator lig ht ]
A white light triple flashes every 10 seconds.
An alternating white and blue light flashes.
A blue light flashes at every 8 seconds.
A blue light flashes rapidly.
The battery is low.
The headset is in pairing mode.
The headset is both paired & connected.
The headset is switched on but not connected.
If no connection can be made, the headset will
turn o itself after 5 minutes.
Press & hold
for 2 sec.
Press twice
Press once
Please refer to www.onkyo.com/welcome for the full user manual
English:
Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
FCC rules
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Relocate the receiving antenna.
• Increase the separation between equipment and receiv er .
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canada:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
Two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAN ICES-3(B)/NMB-3(B)
IC Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments.
This transmitter must not be co-located or oper ati ng in conj unc tion w ith any other antenna or transmitter.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Loading...