Giant PreRunner Jog Stroller User Manual

Giant PreRunner Jog Stroller
Owner's Manual

Assembly and Maintenance

PLEASE READ THE FOLLOWING BEFORE BEGINNING ASSEMBLY:

Do not use your stroller with roller skates or in-line skates. An
accident could occur resulting in serious injury or death.

Insure the stability of the stroller by always carrying heavier items
in the lower cargo basket and lighter objects in the seat back
pocket.

Before assembling your GIANT PreRunner Jog Stroller all of us at
GIANT strongly encourage you to read this manual. In return for the
time spent reading this manual and learning about your new GIANT
PreRunner Jog Stroller you will be rewarded with many hours of safe
usage.

WARNING! WE RECOMMEND THE USE OF A SAFETY HELMET
APPROVED BY THE CONSUMER PRODUCT SAFETY COMMISSION
(CPSC) FOR ANY CHILD USING THIS RIDE-ON TOY.

WARNINGS!

Avoid serious injury from falling or sliding out. Always secure
child in stroller using the safety harness as described.

Always wear an approved bicycle helmet.

Never leave a child unattended in this stroller.

Always use parking brake when the stroller is stationary.

A child may slip into the leg openings of the safety harness and
strangle unless they are properly secured. Never leave child in
this stroller unless they have been properly secured in the safety
harness.

Child must be old enough to sit upright unassisted.

Do not overload your stroller. Maximum load is 75lbs, including
passenger and cargo.

Make sure your child remains seated in the stroller at all times.

Use wrist safety straps all the times.

Do not hang objects from the stroller. This could destabilize the
stroller.

Avoid hitting obstacles with wheels.

Read and understand entire owner's manual prior to use.

Keep children away from plastic packaging.

Assembly

Before assemble your Giant PreRunner Jog Stroller. Please check
that you have all the following parts:

Main Frame x 1
Foot Rest x 1
Front Wheel x 1
Bolts set for Footrest installation
Rear Wheels x 2
6mm hex key wrench
Handlebar & Stem x 1

MAINTENANCE:

Your GIANT PreRunner is a quality Jog Stroller. It has been
constructed utilizing quality components and fasteners. Contact
your local Authorized GIANT Retailer for replacement parts and
service. With periodic maintenance, common sense usage, and care
this Jog Stroller can provide many years of using enjoyment.
Periodically check all of the fasteners to insure that everything is
securely tightened. Check the handlebars to make sure that they
secure. Replace any broken or worn parts as necessary.

Be sure the stroller frame is completely unfolded with latching
mechanisms secure and wheels locked in the place, before
allowing children near the stroller.

Check that all buckles, snaps, straps and adjustments are secure
before each use.

Check and maintain tire air pressure as specified on the side of
tire.

STEP #1 - Install Rear Wheels

STEP #3 - Install the Handlebar & Stem Assembly

Firmly depress the gray button marked push.

Insert the rear wheel into rear axle tube on the rear frame stay.

Release button and test wheel is locked in place. If not, try again.
The wheel must be firmly locked in place.

Repeat the process for both rear wheels.

STEP #2 - Install Front Wheel

a. PreRunner LX, 20" Wheels

Firmly depress the gray button marked push.

Insert the front wheel into axle tube on the front fork.

Release button and test wheel is locked in place. If not, try again.
The wheel must be firmly locked in place

b. PreRunner, 16" Wheels

Move quick release lever so that the word "OPEN" stamped on the
lever arm shows to the outside.

Insert the front wheel between the fork blades so that the axle
seats firmly at the top of slots, which are at the tips of fork
blades - the fork dropout.

Giant PreRunner Jog Stroller has bicycle style handlebar and
stem that allows the handlebar height to be adjusted to
accommodate a wide variety of users.

Loosen the handlebar binder bolts then remove the stem clamp

-(Fig. a), and keep the bolts on the stem.

Fit the stem and clamp-(Fig. a) on the plastic shim at the top of
the stroller frame then tighten the handlebar binder bolts so that
the stem will stay in place by itself, but is still easy to adjust.

Try to find the best position for the user and tighten the handlebar
and stem binder bolts.

Push down the handle bar to raise the front wheel to test that the
Be bolts were sufficiently tightened.

STEP #4 - Install the Footrest fender on the Frame

Assemble footrest fender as shown in the diagram.

Align the heads of the bolts to fit into the matching recesses in the
footrest fender.

CAUTION: Avoid crushing the frame tubing DO NOT OVER TIGHTEN
BOLTS! Tighten only until hand snug.

Flip quick release lever so that the word "CLOSED" stamped on
the lever arm shows to the outside.

Closing quick release lever should get progressively firmer until it
is solidly fixed in the closed position.

If quick release lever cannot be fully closed, loosen thumbnut on
the opposite end of the skewer and try to close it again.

If the lever goes to the closed position too easily or feels loose in
the closed position, open the lever and tighten thumbnut, then try
closing again.

Quick release lever should be parallel to the front fork blade when
in final closed position.

CAUTION: DO NOT operate stroller if wheels do not firmly lock in
place.