Gianni Industries ST-630E User Manual

ST-630E Access Control Unit

Operation Manual (S1 Mode/On line)

Features:



Master card and codes Auto reset function



Security system setting / Release



Synchronize with security system



Entering / Exiting programming mode: Only



proximity, Codes + proximity, Codes or proximity Door status monitor function



Anti pass back function



Emergent access alarm, time delay alarm and forced door alarm output



Dual relays programmable On / Off or pulsed or latched mode



LED indicator to distinguish the status



Use for all kinds of the electric lock

 

Use software to connect up to 254 controllers

Specifications:

Part No Connection Users Record volumes Reader application Keys Interface Proximity distance Proximity frequency Indicators Dimension(mm) Operating voltage Temperature Humidity

ST-630E On line 1000 1000 WG26,WG34 12 keys (0-9,*,#) RS485 10~15cm 125Khz (EM) 3 LEDs 114(L)x69.5(W)x10(D)mm 12VDC

-5C~60ºC 5%~95%(Non-condensing)

Operation Instruction：

*XXXXXX# * # 01*XXXXXXxxxxxx# 02*XXX# 03*XXX#

10*xxxxx*XXXXXXXXXX#

12*xxxxx*XXXXX#

13*xxxxx*XXXXX*N#

14*xxxxx*XXXX# 15*99# 17*XXXXXXXXXX# 21*XXX#

22*XXX#

25*X# 26*XXXXX*XXXXX#

32*X# Anti-pass-back function X=0 / OFF X=1/ ON 33*X#

34*99# 35*X# 51*99#

55*99# 71*XXXXXXxxxxxx#

72*XXX#

73*X# 74*X#

76*X# 99*

Enter program mode, enter 6-digit codes (Default 123456) Exit program mode Change default password, press twice new 6-digit codes Controller station setting (001-254)

Time Delay Setting from 000-250 seconds. 000= toggle mode. Adding or revise the card No.

Slot position=00001~01000 and enter the 10-digit card No. Adding the card No. in sequence. xxxxx=the beginning slot position XXXXX=the quantity of cards. After setting the quantity of cards, read the first card and press “#” to complete the setting. The access mode is for Card Only after adding the cards.

(p.s.X

≦

Access mode and clear card setting xxxxx=The beginning slot position XXXXX=the end slot position

Slot position=00001~01000

N indicates the access mode. 0=Access not allowed, 1=Card Only, 2=Card or Code, 3=Card & Code, 4=Clear card information

Code setting: xxxxx=slot position XXXX= 4-digit code (Position=00001~01000) Clear all cards (Not including master card)

Enter card no. to clear the information when forget the slot position. X=10 digit card no.

Alarm output time setting XXX=000~255 seconds The second relay activate time. XXX=000~250 seconds (Second relay for security

system) (000 manual mode) (Default value is 15 seconds) Master cards setting X=(1 or 2) 2 Master card available

Under normal status, proximity the master cards to program mode

Security card arrange setting: XXXXX=00001~01000 (The range of the No. should be

succeeding without a break in numbering.

Two doors synchronize X=0/OFF X=1/ON Access controller and reader can control different doors. Clear the function of Anti-pass-back

X=1=access record to duty X=0=access record Not to Duty X=default is 0 Reset to default, and clean the controller memory to the factory default.

Read card once and hear 1 Beep to add new card. Read card twice and hear 2 beeps

to clear the card (The default access mode for this instruction is Card Only).

Set the emergent code by entering 6-digit code twice. Enter the code to activate the second relay. Accompany with the instruction of 22*XXX# to set the second relay active time.

Door left open alarm time delay setting. XXX=000~255 seconds. The door status reed switch is required for this function. The second relay active alarm output after the limited time. (Refer to 21*XXX#) X=1 Enter the emergent code or press 99* with security cards, the relay of the controller will be avtivated. X=0/OFF Door left open alarm and force open mode are setting. X=1/ON, X=0/OFF Emergent alarm setting X=1/ON, X=0/OFF

Active the second relay by press the code 99* first, and read the valid card. (without entering the program mode).

01000)

(Suggested Card: CCTR00-CNPSLD-CN)

Indicators Status and Default Value:

Beep & LED indication：

Status

LED

Beep

Mode Signal

Yellow(Flash slowly)

Normal

Green On Red On

Programming

Normal

Yellow (Flash quickly) Red(Flash quickly)

1 Beep 2 Beep 1 Beep

Programming

2 Beep

Power-on, stand-by Valid entry, door relay active

Warning, invalid card or code, tamper,alarm relay active

Enter programming mode Card read, or clear the memory

valid card, keypress, entry program mode

Invalid cards, mistake codes Valid entry, exit the program mode Incorrect input or other failed operation

Wiring Diagram:

Door one

Locking Device 1 (Fail-Safe)

Factory default setting：

Access mode Card memory

Transaction memory (MAX 1000 cards)

Master codes (Master password) (All) Functions of alarm Door relay time Key timeout Awaiting code timeout Programming mode timeout

Door two

Locking Device 1

(Fail-Safe)

Card only (0000) All Bits 0 pcs *123456# Clear the function (00) 3 seconds 5 seconds 5 seconds 25 seconds

For DC use only For AC/DC

The door strike must have a vartistor or a diode across the door strike terminals to suppress the back EMF of the strike-failure to do so will damage the relay contacts and electronic components.

Relay Relay

White Green

RS 485

Red;+10~14Vdc Black:V0 Orange:D1 Yellow:D0 Blue:LED(Yellow) Pink:LED(Red) Green:LED(Green)

Blue:N.O.2

Green:Com.2

Yellow:N.C.2

Gray:P2

Gray:B2

White:P1

White:B1

Brown:Reed Brown:Reed

Auxiliary Reader

Locking Device 2 (Fail-Secure)

Door status reed switch contact is (N. O.) The contact switch is in N.O.(Normal Open) status when the door closes. The contact switches to N.C. (Normal Close) when the door opens.

Push Button 2

Computer

Push Button 1