Gianni Industries DG-15 User Manual

DG-15 series Digital Keypad Entry system

Operation User's Manual

1. Specifications:

 Operating Voltage: 12 Vdc
 Current Draw: Average 15mA, Peak 100mA @ 12Vdc
 Input: request-to-exit, time out reed switch contact
 Output: Dual relays, N.O./N.C./Com. Output (free voltage

contact)

 Relays Electric Current: 2A MAX @30Vdc ；0.4A @

120Vac

 Relay Activation Time:

 Relay 1 time delay setting code「＊30」、Relay 2

setting code「＊31」

 Strike Time: 1~99 seconds（adjustable）
 Strike mode: Access Timer or Latch

 Memory Volume: 20+1 PIN codes

 Relay 1 is controlled by ＊01~＊20 user slots
 Relay 2 is controlled by ＊21 user slots

 Operating Temperature: -20~+70℃
 Ambient Humidity: 5~95% relative humidity non-condensing
 Factory Master Code: 12345
 Invalid PIN Lock-out: The system will shut down for 60 seconds while 30 codes of

incorrectly Master Codes enrolled or PIN codes attempted（None beeper signal of
keypad activations）.

 EPROM: Non-volatile memory, System will retain all programs and codes after a total

loss of power.

 The indicator signal chart:

LED signal Sound signal

Green LED Power on, stand-by 1 Beep

Red LED Relay 1 activated 2 Beeps

Yellow LED Relay 2 activated 3 Beeps Data computing error

5 Beeps

Effective PIN codes、Any key pressed

Entering 、Exiting from the Program mode

Master Code reset to Factory （12345）

2. Operation Instruction:
 Enter Program Mode:

1. Compose twice the master code (4 digit format press「1234」、5 digit format press
「12345」) → 2 beeps → you are now in the "programming mode".

2. After 60 seconds if you have not entered any codes or data, the system will
automatically exit from the programming mode.

 Exiting from the program mode:

1. Press「#」 to exit from the programming mode.

2. After 30 wrong codes attempts at the master code the lockout facility will operate.

 Add PIN codes

Enter the Programming mode, Enter the slot position code 「＊01~＊20」→????? Input
5 digit （or 4 digit）PIN codes→ (beep) enrolled Æ（repeat）
Press 「#」 to exit from the programming mode, or program other operating.

Note 1: The codes「0000」,「00000」,「1234」,「12345」or master code are not be

used for PIN code.

Note 2: Relay 2 is controlled by ＊21 user slots

 To Delete a User Code：

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG15 Ver. C Publish:2008.11.12 Page: 1/ 3

Enter the Programming mode→ Press the slot position code of your choice to delete

(example "06") →Press「＊06」→「0000」（or「00000」）→（beep）→delete→
Press「#」 to exit from the programming mode, or programming other operating.

 To Program Relocking Timer
Enter the Programming mode,

A. Relay 1：Press「＊30」Followed by the number of seconds the relay should

open→「05」=5 seconds（01 ~99 = seconds,「00」Sets the relay to latching
mode）→（beep）→enrolled → Press 「#」 to exit from the programming mode,
or program other operating.

B. Relay 2：Press「＊31」Followed by the number of seconds the relay should

open）→「05 =5 seconds (01 ~99 = seconds,「00」Sets the relay to latching
mode). →（beep）→enrolled → Press 「#」 to exit from the programming mode,
or program other operating.

C. Latching mode: Correct code entered opens the relay, and the relay stays open until

the correct code is entered again.

 Changing the Master codes:
Enter the Programming mode, Enter「＊00」Followed by the new 4 digit （or 5 digit）

master code→（beep）→enrolled→Enter 「#」 to exit from the programming mode, or
program other operating.

 Reset to Factory

 Master Code reset to Factory 「12345」

Insert the jumper RESETÆ 1-2 positionÆ5 audible beepsÆReset successfulÆ Return
Insert the jumper to 2-3 position

 Remove all stored information

Insert the jumper RESETÆ 1-2 positionÆ5 audible beepsÆ Master Code reset to
Factory 「12345」Æ after 5 secondsÆ5 audible beepsÆ Remove all stored
information Æ Return Insert the jumper to 2-3 position.

Note: If you only wish to reset the Master Code to the Factory default, remove the

jumper after exactly 5 audible beeps, otherwise all cards / codes will be deleted.

3. Wiring diagram:

Fail-Safe

Locking Device 2

Contact door reed switch

This reed switch is used
to reset the re-lockin g time
to 0 second when the door

is moved.

Syste m 4 or 5 digit code s etting

4 digi t 5 digit

Power Supply

Push Button

4OR5

RESET

Relay 2

Relay 1

Resetting Normal

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG15 Ver. C Publish:2008.11.12 Page: 2/ 3

4OR5

RESET

Master Code resetting to

Factory Code"12345"