Gianni Industries BTS-486 User Manual

Specifications

BTS Touch Exit Button
Installation Instruction

Mode
Operating Voltage

Current Draw
Relay contact

output
Relay rating

Relay strike time
LED status

indication
Temperature

Other

BTS-100 BTS-115-ANSI,115-S BTS-400ANSI,300BTS-85UK BTS-486

12~24VDC 12~24VDC 12~24VDC 12~24VDC 12~24VDC

30~60mA/12VDC
40~80mA/24VDC

Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O

3A/30VDC 3A/24VDC 3A/24VDC 3A/24VDC 3A/24VDC

1~30 seconds

Green(Relay) Green(Relay) Green(Relay)

-20~+70ºC

30~50mA/12VDC
40~60mA/24VDC

1~30 seconds

-20~+70ºC

Wiring Diagram

The BTS touch sensitive exit button has
N.O. and N.C. contact output and can be
connected directly to a electromagnetic lock
or a proximity reader in series (or in parallel).

20~40mA/12VDC
20~50mA/24VDC

1~30 seconds 1~30 seconds 1~30 seconds

-20~+70ºC -20~+70ºC

Control Device (Outdoor)

Relay output
control

60~100mA/12VDC
80~120mA/24VDC

2x6 levels of LED
indicator

30~60mA/12VDC
40~80mA/24VDC

2x6 levels of LED
indicator

-20~+70ºC

N/O,N/C output setting

Fig.A

In Fig.A, BTS controls the fail-safe locking
device directly by series connection. BTS
relay time is door-opening time.

Power

1

30 sec.

Relay Timer

Locking Device

(fail-safe)

Supply

BTS Touch Sensitive Switch (Indoor)

Control Device (Outdoor)

Fig.B

In Fig.B, BTS controls the fail-secure locking
device directly by parallel connection. BTS

Relay output
control

relay time is door-opening time.

Locking Device

(fail-secure)

Power

1

30 sec.

Relay Timer

Supply

BTS Touch Sensitive Switch (Indoor)

Note:

1. Make sure that the power input and relay rating output (3Amp/24VDC) are correct.

2. Make sure that the “+” and “-” wires are connected correctly.

3. The door strike or relay must have a varistor or a diode across the door strike terminals to suppress the
back EMF of the strike. Failure to do so will damage the relay contacts and electronic omponents, or
even burn the controller.

Copyright © GIANNI Industries,Inc.All rights reserved.
P-MU-BTS Ver.D Published 2011.03.18

Illustration

BTS Touch Exit Button

Base
Slot hole

LED

Vandal resistant screw
Stopper
Touch panel

JP setting

The relay will send the signals from N.C.
into N.O. contact after your finger or a
metal object touches the touch panel.
Time delay can be adjusted from 1 to 30
seconds.

Relay output

Relay output

(Light stay on)

(Light flash)

(Green)

(Red)

(Green)

(Off)

(Red)

(Off)

(Touch)

(Touch)

(Touch)

(Touch)

(Touch)

(Touch)

(Touch)

(Touch)

Relay output

Relay output

(Red)

(Green)

(Off)

(Green)

(Off)

(Red)

BTS-400-ANSI,300,486

Relay contact output

(dry contact)

12~24 VDC power input

JP setting

Relay Timer

(Sec.)

Warranty

The product is warranted against defects in material and workmanship while used in normal service for
a period of 1 year from the date of sale to the original customer. The GEM policy is one of continual
development and improvement; therefore GEM reserves the right to change specifications without notice.

Copyright © GIANNI Industries,Inc.All rights reserved.
P-MU-BTS Ver.D Published 2011.03.18