GEV 016934, 016910 User guide [ml]

GEV GmbH Heidehofweg 16 25499 Tangstedt
Germany
www.gev.de
Hotline: +49 (0)180/59 58 555
Max. 14 Ct./Min aus dem deutschen Festnetz.
Mobil max. 42 Ct./Min.
International calls may vary.
16WOA28
BA01176200
www.gev.de
Typ: Unterputz-Bewegungsmelder AGON LUX 160° LBM 16934 AGON KOMBI 160° LBU 16910
16934
16910
A
5min
30s
90s
30
300
5min
10min
30min
10s
30s
90s
10
30
300
B
-
N L L
C
1 2
D E
N L' L
2 3
N L' L
L' L
N
OFF PIR ON
10s
10min
30min
10
OFF PIR ON
Unterputz-Bewegungsmelder AGON LUX 160° LBM 16934 AGON KOMBI 160° LBU 16910
Funktion
Der Unterputz-Bewegungsmelder AGON 160° ist für die Wandmontage geeignet und wird anstelle eines herkömmlichen Lichtschalters in einer Unterputzdose eingebaut. Der Bewegungsmelder arbeitet nach dem Prinzip der Passiv­Infrarot-Technik. Sich bewegende Wärmequellen werden in dem Erfassungsbereich von 160° von dem PIR-Sensor wahrgenommen. Die Schaltzeit und die Dämmerungsfunktion sind stufenlos einstellbar.
Sicherheitshinweise
Die Montage darf nur von einem Fachmann unter Berücksichtigung der landesüblichen
Installationsvorschriften ausgeführt werden. Es darf nur in spannungsfreiem Zustand gearbeitet werden, dazu unbedingt die Stromkreissicherung abschalten.
Überprüfen Sie, ob die Anschlussleitung spannungsfrei ist!
Bei Schäden, die durch Nichtbeachtung dieser Bedienungs­anleitung verursacht werden, erlischt der Garantieanspruch! Für Folgeschäden übernehmen wir keine Haftung! Bei Sach- oder Personenschäden, die durch unsachgemäße Handhabung oder Nichtbeachtung der Sicherheitshinweise verursacht werden, übernehmen wir keine Haftung. In solchen Fällen erlischt jeder Garantieanspruch. Aus Sicherheits- und Zulassungsgründen ist das eigenmächtige Umbauen und/oder Verändern des Gerätes nicht gestattet.
Montageort
Der Unterputz-Bewegungsmelder 160° reagiert auf Wärmequellen. Um Fehlschaltungen zu vermeiden sollte er nicht oberhalb von Heizungen oder dem direkten Sonnenlicht ausgesetzt werden
(Abb. A). Installation
Lösen Sie den Rahmen und den Sensor. Die Verdrahtung des
Gerätes kann jetzt nach dem Schaltschema vorgenommen werden (Abb. B). Über N + L´ können Sie den zu schaltenden Verbraucher, z. B. eine Leuchte, o. ä. anschließen. Alternativ kann der AGON KOMBI 160° LBU 16910 auch in Zweidrahttechnik angeschlossen werden (Abb. B2). Führen Sie die Versorgungseinheit in die Unterputzdose und ziehen Sie die Befestigungskrallen links und rechts an. Fixieren Sie den Zwischenrahmen mit der Sensorabdeckung (Linsenkörper) durch einfaches Aufrasten.Jetzt kann die Stromkreissicherung wieder eingeschaltet werden.
Einstellung
Um in den Testbetrieb zu gelangen, stellen Sie bitte die Regler wie in der (Abb. E) ein. Mit Hilfe der Time- und Lux-Regler können individuelle Einstellungen vorgenommen werden (Abb. E). Durch den Schiebeschalter (Abb. E) sind weitere Funktionen möglich: OFF = AUS: Bei Wechsel eines Leuchtmittels den Schalter immer in diese Position bringen PIR = Automatikbetrieb: Der Bewegungsmelder schaltet das Licht bei Erfassung einer Bewegung ein und nach der vorgewählten Zeit - wenn keine weitere Bewegung erfasst wurde - wieder aus ON = Dauerlicht: Der Verbraucher bleibt dauerhaft eingeschaltet
AGON LUX LBM 16934
Fällt der gemessene Lichtwert unter den eingestellten Wert, schaltet sich leicht verzögert das Nacht-/ Orientierungslicht der integrierten LED ein.
Recycling-Hinweise
Dieses Gerät darf nicht mit dem unsortierten Hausmüll entsorgt werden. Besitzer von Altgeräten sind gesetzlich
dazu verpflichtet, dieses Gerät fachgerecht zu entsorgen. Informationen erhalten Sie von Ihrer Stadt- bzw. Gemeindeverwaltung.
4 5
Fehleranalyse – Praktische Tipps
Störung Ursache Abhilfe
Störung Bewegungsmelder schaltet zu spät • Bewegung frontal Höher montieren. Reichweitenregler auf „max.” stellen Maximale Reichweite wird nicht erreicht • Bewegungsmelder zu niedrig angebracht
Lampe leuchtet ständig oder unerwünschtes Schalten der Leuchte
Kein Schalten von Licht • Sicherung defekt • Leuchtmittel defekt
Technische Daten AGON LUX 16934
Erfassungsbereich 160° Netzspannung 230 V ~, 50 Hz Reichweite Bis ca. 8 m Zeiteinstellung Ca. 10 Sek. – 7 Min. stufenlos einstellbar Umgebungstemperatur Ca. -15 °C bis +45 °C Schaltleistung Max. 200 W LEDs, max. 200 W Energiesparlampen, max. 500 W Glühlampen Schutzklasse II Empfohlene Montagehöhe Ca. 0,8 m – 1,2 m
Technische Daten AGON KOMBI 16910
Erfassungsbereich 160° Netzspannung 230 V ~, 50 Hz Reichweite Bis ca. 8 m Zeiteinstellung Ca. 10 Sek. – 7 Min. stufenlos einstellbar Umgebungstemperatur Ca. -15 °C bis +45 °C Schaltleistung Min. 40 W – max. 400 W Glühlampen, ca. 40 W – 150 W für Halogenlampen, 12 V Niedervolt-Halogen min. 40 VA – max. 150 VA (elektronischer Transformator) Schutzklasse II Empfohlene Montagehöhe Ca. 0,8 m – 1,2 m
• Temperaturdierenz von Umgebung zur Wärmequelle ist zu gering
• Ständige Wärmebewegung: Anbringung des Bewegungsmelder über einer Wärmequelle, z. B. Heizkörper oder Beeinflussung durch Sonneneinstrahlung, direkt/indirekt
• Mind. Last von 40 W beachten
μ = Kontaktönungsweite < 1,2 mm
Technische und optische Änderungen ohne Ankündigung vorbehalten.
Höher montieren Reichweitenregler auf „max.” stellen
Sicherung wechseln
DEGBFRITPL
Recessed-mounted motion detector AGON LUX 160° LBM 16934 AGON KOMBI 160° LBU 16910
Function
The AGON 160° recessed-mounted motion detector has been designed for wall mounting and is installed in a recessed­mounted box instead of a conventional light switch. The motion detector functions using passive infrared technology (PIR). The device has an in-built PIR sensor that detects moving heat sources within a field of detection of 160°. The switching times and the twilight feature are infinitely variable.
Safety instructions
This device must be installed by a technician in accordance with the applicable regulations. The
electrical power supply must be switched o throughout the entire installation process. To guarantee this, the circuit protection must be switched o.
Please check that the connection cable is disconnected!
Under no circumstances does the warranty cover damage resulting from failure to observe these instructions. Nor do we accept liability for any indirect damage. Similarly, we can accept no liability for any material damage or bodily injury caused by mishandling or failure to observe the safety instructions. No warranty claim may be made in these cases. In addition, for safety and compliance reasons, you are not authorised to dismantle or alter the device in any way.
Mounting position
The 160° recessed-mounted motion detector reacts to sources of heat. To prevent switching errors, ensure that the device is not installed above heaters or exposed to direct sunlight (fig. A).
Installation
Remove the frame and the sensor. Now, connect up the device as shown in the wiring diagram (fig. B). Alternatively, the AGON KOMBI 160° LBS 16910 can also be connected in two-wire technology (fig. B2). Place the supply unit in the recessed-
mounted box and tighten the two fastening claws on the left and right. Now attach the sensor section, screw it to the supply unit and replace the cover frame. Finally, switch the circuit protection on.
Settings
To enter test mode, configure the controller as displayed in (fig. E). The metre, time and Lux controllers can be used to configure individual settings (fig. E). Additional functions can be selected using the sliding switch (fig. E): OFF = switched o: Always move the switch to this position when replacing the illuminant PIR = automatic mode: The motion detector switches on the light when it detects movement and then turns the light o after the preset time has elapsed, provided that the detector has not detected any further movement ON = continuous lighting: The consumer remains permanently switched on
AGON LUX LBM 16934
If the measured light value falls below the set value the integrated LED light switches on slightly delayed.
Recycling instructions
Do not dispose of this device with unsorted household waste. Owners of old devices are required by law to dispose of this device properly. Contact your town council for further information.
Troubleshooting - practical advice
Fault Cause Solution
Motion detector responds too late • head-on movement Install the device higher up. Adjust the range
Maximum range is not reached • Motion detector is mounted too low
Lamp is permanently lit or light is switched on when not needed
Light does not switch on • Faulty fuse • Faulty illuminant
Technical information AGON LUX 16934
Field of detection 160° Mains voltage 230 V ~, 50 Hz Range up to approx. 8 m Time setting approx. 10 seconds to 7 minutes - infinitely variable Ambient temperature approx. -15 °C to +45 °C Switching capacity max. 200 W LEDs, max. 200 W energy saving lamp, max. 500 W incandescent lamps Protection class II Recommended installation height approx. 0.8 m – 1.2 m
Technical information AGON KOMBI 16910
Field of detection 160° Mains voltage 230 V ~, 50 Hz Range up to approx. 8 m Time setting approx. 10 seconds to 7 minutes - infinitely variable Ambient temperature approx. -15 °C to +45 °C Switching capacity 40 – 400 W for incandescent lamps, 40 – 150 W AC for halogen lamps, 40 – 150 VA for 12 V low-voltage halogen lamps (electronic transformer) Protection class II Recommended installation height approx. 0.8 m – 1.2 m
• Dierence between the ambient temperature and the source of heat is negligible
• Constant warm movements; the motion detector has been installed above a source of heat (e.g. a heating device) or has been exposed to direct/indirect rays of sunlight
• Observe minimum load of 40 watts
controller to “max.” Install the device higher up Adjust the range controller to “max.”
Replace fuse
μ = contact gap < 1.2 mm
Subject to technical and design changes without prior notice.
76
DEGBFRITPL
Détecteur de mouvement à encastrer AGON LUX 160° LBM 16934 AGON KOMBI 160° LBU 16910
Fonctionnement
Le détecteur de mouvement encastré AGON 160° est conçu pour un montage mural et s’intègre dans un boîtier encastré, à la place d’un interrupteur classique. Le détecteur de mouvement utilise la technologie infrarouge passive. Le capteur infrarouge passif intégré perçoit les sources de chaleur en mouvement dans une zone de détection de 160°. Les durées d’activation et la fonction crépusculaire sont réglables en continu.
Consignes de sécurité
L’installation de ce produit doit impérativement être eectuée par un spécialiste et conformément aux prescriptions en vigueur. L’alimentation électrique doit
obligatoirement être coupée. Pour cela, le fusible doit être retiré.
Le câble d’alimentation ne doit être soumis à aucune tension.
La garantie ne couvre en aucun cas les dommages dus à un non-respect de la présente notice. Nous déclinons par ailleurs toute responsabilité quant aux éventuels dommages indirects. De même, nous ne pourrons être tenus pour responsables des éventuels dommages matériels ou blessures corporelles résultant de manipulations inappropriées ou du non-respect des consignes de sécurité. Dans de tels cas de figure, tout recours en garantie sera exclu. En outre, pour des raisons de sécurité et de conformité, le démontage et la modification du produit sont interdits.
Lieu de montage et positionnement
Le détecteur de mouvement encastré 160° réagit aux sources de chaleur. Pour éviter son déclenchement intempestif, il ne doit pas être monté au-dessus d’un chauage ni exposé à un ensoleillement direct (fig. A).
Installation
Retirez le cadre et le capteur. Raccordez l’appareil selon le schéma de connexion (fig. B). En variante, le AGON KOMBI
160° LBU 16910 également être connecté à la technologie bifilaire (fig. B2). Positionnez l’unité d’alimentation dans le boîtier encastré et insérez les deux gries à gauche et à droite. Fixez ensuite la partie capteur en la vissant à l’unité d’alimentation et placez le cadre. Pour finir, mettez en place le fusible secteur.
Réglage
Pour accéder au mode de test, configurez le régulateur comme illustré à la (fig. E). Les régulateurs de distance, de durée et de luminosité vous permettent d’eectuer des réglages individuels (fig. E). Le sélecteur (fig. E) vous permet en outre de régler les fonctions suivantes : OFF = ARRÊT : veillez à toujours mettre le sélecteur sur cette position avant de changer une source lumineuse PIR = mode automatique : le détecteur de mouvement allume le luminaire en cas de détection d’un mouvement et l’éteint à nouveau après une durée définie si aucun autre mouvement n’a été détecté
ON = Éclairage permanent : l’appareil reste allumé en continu AGON LUX LBM 16934
Si la valeur de lumière mesurée est inférieure à la valeur de consigne tourne légèrement retardé la lumière nuit / orientation intégré Led.
Remarques concernant le recyclage
Cet appareil ne doit en aucun cas être jeté avec les ordures ménagères. Les propriétaires d’équipements électriques
ou électroniques usagés ont en eet l’obligation légale de les déposer dans un centre de collecte sélective. Informez-vous auprès de votre municipalité sur les possibilités de recyclage.
Dysfonctionnements – Conseils pratiques
Problème Causes possibles Marche à suivre
Le détecteur de mouvement réagit trop tard La portée maximale n'est pas atteinte • Détecteur de mouvement installé trop bas
La lampe est allumée en permanence ou s'allume de façon intempestive
L'éclairage ne s'allume pas • Fusible défectueux • Ampoule défectueuse
Caractéristiques techniques AGON LUX 16934
Zone de détection 160° Alimentation 230V~, 50Hz Portée jusqu'à 8m env. Durée d'activation env. 10s à 7min, réglable en continu Température ambiante de fonctionnement Puissance de commutation max. 200 W LEDs, max. 200 W lampes à économie d‘énergie, max. 500 W à incandescence Classe de protection II Hauteur de montage recommandée env. 0,8 m à 1,2 m
Caractéristiques techniques AGON KOMBI 16910
Zone de détection 160° Alimentation 230V~, 50Hz Portée jusqu’à 8m env. Durée d’activation env. 10s à 7min, réglable en continu Température ambiante de fonctionnement Puissance de commutation Puissance de coupure ampoules à incandescence : 40 à 400 W, ampoule halogène AC de 40 à 150 W, ampoules halogènes basse tension 12 V : 40 à 150 VA (transformateur électronique) Classe de protection II Hauteur de montage recommandée env. 0,8 m à 1,2 m
• Déplacement frontal Installer le détecteur de mouvement plus haut. Régler le
• Écart trop faible entre la température ambiante et la source de chaleur
• Détection continuelle de sources de chaleur en mouvement: Le détecteur de mouvement a été installé au-dessus d'une source de chaleur (p. ex. un radiateur) ou est exposé à un ensoleillement direct/indirect
• Tenir compte de la charge minimale de 40W
potentiomètre de portée sur «max.» Installer le détecteur de mouvement plus haut Régler le potentiomètre de portée sur «max.»
Remplacer le fusible
-15 °C à +45 °C env.
-15 °C à +45 °C env.
μ = largeur d’intervalle de coupure < 1,2mm
Modifications techniques et optiques réservées sans avertissement préalable.
98
DEGBFRITPL
Rilevatore di movimento incassabile AGON LUX 160° LBM 16934 AGON KOMBI 160° LBU 16910
Funzione
Il rilevatore di movimento da incasso con copertura a AGON 160° è ideale per l’installazione a parete. A dierenza dei tradizionali commutatori per illuminazione viene installato all’interno di un alloggiamento incassato. Il rilevatore di movimento sfrutta il principio alla base della tecnologia a infrarossi passivi. Un sensore PIR integrato rileva fonti di calore in movimento con un angolo di copertura di 160°. I tempi di commutazione e la funzione crepuscolo sono dotati di regolazione continua.
Indicazioni di sicurezza
Il montaggio deve essere svolto esclusivamente da personale specializzato, nel pieno rispetto delle norme di installazione locali. Operare solo in assenza di tensione.
Disinserire l’interruttore automatico del circuito elettrico.
Verificare che il cavo sia privo di tensione!
In caso di danni derivanti dalla mancata osservanza delle istruzioni per l’uso, la garanzia decade. Il produttore non si assume alcuna responsabilità in merito a tali danni. Inoltre, il produttore non si assume alcuna responsabilità in caso di danni a cose o persone conseguenti a un utilizzo inadeguato del dispositivo o alla mancata osservanza delle norme di sicurezza. Nei suddetti casi decade ogni diritto di garanzia. Per motivi relativi a sicurezza e certificazioni, non è consentito apportare variazioni e/o modifiche arbitrarie al dispositivo.
Luogo di installazione
Il rilevatore di movimento da incasso con copertura di 160° reagisce alle fonti di calore. Per evitare commutazioni indesiderate, si raccomanda di procedere all’installazione in luoghi che non siano direttamente esposti a fonti di calore o alla luce diretta del sole
Installazione
Rimuovere la cornice e il sensore. Collegare l’apparecchio come
(fig. A)
.
illustrato nello schema (fig. B). In alternativa, l’AGON KOMBI 160° LBS 16910 può anche essere collegato in tecnologia a due fili (fig. B2). Posizionare l’alimentatore nell’alloggiamento incassato e tirare entrambe le zanche di fissaggio a destra e a sinistra. Procedere quindi al fissaggio del sensore, avvitarlo all’alimentatore e riposizionare la cornice di chiusura. Inserire poi l’interruttore automatico del circuito elettrico.
Regolazione
Per eettuare il test di funzionamento, impostare il regolatore come mostrato (fig. E). Grazie al regolatore dei metri, del tempo e dei lux, è possibile personalizzare le impostazioni (fig. E). Tramite l’interruttore a scorrimento (fig. E) sono disponibili funzioni aggiuntive: OFF = SPENTO: spostare sempre l’interruttore in questa posizione quando si cambiano le lampade PIR = Funzionamento automatico: il rilevatore di movimento accende la luce quando rileva un movimento e, dopo l’intervallo di tempo preimpostato, la spegne se non rileva altri movimenti
ON = Luce continua: l’utenza resta accesa in modo continuativo AGON LUX LBM 16934
Se il valore di luce misurata scende al di sotto del valore impostato, la luce notturna LED integrato è leggermente ritardato su.
Indicazioni per il riciclaggio
Questo dispositivo non deve essere smaltito come rifiuto
indierenziato. I possessori di vecchi dispositivi non
funzionanti sono tenuti per legge allo smaltimento nel rispetto delle normative in vigore. Per ulteriori informazioni rivolgersi all’amministrazione comunale.
Analisi dei problemi – Consigli pratici
Malfunzionamento Causa Soluzione
Il rilevatore di movimento si aziona troppo tardi Non viene raggiunta la portata massima • Rilevatore di movimento installato troppo
Le lampade hanno una luce fissa o si accendono arbitrariamente
La luce non si accende • Fusibile bruciato • Lampadina bruciata
Dati tecnici AGON LUX 16934
Angolo di copertura 160° Tensione di rete 230 V ~, 50 Hz Portata fino a circa 8 m Impostazione temporale ca. 10 sec. – 7 min., regolazione continua Temperatura ambiente ca. da -15 °C a +45 °C Potenza di commutazione max. 200 W LEDs, max. 200 W lampadine a risparmio energetico, max. 500 W lampadine Classe di protezione II Altezza di montaggio consigliata ca. 0,8 m – 1,2 m
Dati tecnici AGON KOMBI 16910
Angolo di copertura 160° Tensione di rete 230 V ~, 50 Hz Portata fino a circa 8 m Impostazione temporale ca. 10 sec. – 7 min., regolazione continua Temperatura ambiente ca. da -15 °C a +45 °C Potenza di commutazione potenza di interruzione lampade a incandescenza 40 – 400 W, lampada alogena max. 40 – 150 W CA, lampade alogene a basso voltaggio 12 V 40 – 150 VA (trasformatore elettrico) Classe di protezione II Altezza di montaggio consigliata ca. 0,8 m – 1,2 m
• Movimento frontale Installare più in alto. Impostare il regolatore
in basso
• Dierenza di temperatura tra l'ambiente e la fonte di calore troppo ridotta
• Movimento del calore costante: il rilevatore è stato installato sopra a una fonte di calore (es.: dispositivo di riscaldamento) oppure è direttamente/indirettamente esposto alla luce del sole
• Rispettare il carico minimo di 40 W
della portata su "max." Installare più in alto Impostare il regolatore della portata su "max."
Sostituire il fusibile
μ = apertura dei contatti < 1,2 mm
La ditta si riserva il diritto di apportare variazioni tecniche ed estetiche senza preavviso.
1110
DEGBFRITPL
Podtynkowy detektor ruchu AGON LUX 160° LBM 16934 AGON KOMBI 160° LBU 16910
Działanie
Podtynkowa czujka ruchu AGON 160° jest przeznaczona do montażu ściennego i można ją montować zamiast standardowego przełącznika oświetlenia. Czujki ruchu działają według zasady biernej techniki podczerwieni. Poruszające się źródła ciepła są wykrywane w obszarze detekcji 160° za pomocą wbudowanego czujnika PIR. Czasy przełączania i funkcja zmierzchowa są regulowane bezstopniowo.
Uwagi dotyczące bezpieczeństwa
Montaż może być wykonywany wyłącznie przez specjalistę, przy przestrzeganiu obowiązujących
w danym kraju przepisów dotyczących instalacji elektrycznych. Prace wolno wykonywać wyłącznie po odłączeniu napięcia. W tym celu należy rozłączyć zabezpieczenie obwodu prądowego.
Sprawdź, czy w przewodzie podłączeniowym nie ma napięcia!
W przypadku szkód spowodowanych nieprzestrzeganiem niniejszej instrukcji obsługi gwarancja wygasa! Za szkody wtórne nie przyjmujemy żadnej odpowiedzialności! Nie przyjmujemy odpowiedzialności w przypadku szkód rzeczowych i obrażeń ciała spowodowanych nieumiejętnym postępowaniem lub niestosowaniem się do uwag związanych z bezpieczeństwem. W takich przypadkach wszelkie roszczenia gwarancyjne wygasają. Z przyczyn związanych z bezpieczeństwem i dopuszczeniami technicznymi, samowolne przeróbki lub modyfikacje urządzenia są niedozwolone.
Miejsce montażu
Podtynkowa czujka ruchu 160° reaguje na źródła ciepła. Aby uniknąć niepożądanych przełączeń, nie należy jej instalować nad elementami grzejnymi ani nie wystawiać na bezpośrednie działanie promieni słonecznych (rys. A).
Instalacja
Zdejmij ramę i czujnik. Okabluj teraz urządzenie zgodnie ze schematem (rys. B). Alternatywnie wykonuje urządzenia AGON KOMBI 160° LBU 16910 równiez podlacz technologie dwa drutu dokręć dwa pazury mocujące z lewej i prawej strony. Zamontuj teraz moduł czujnika, przykręć go do zasilacza i nasadź ramkę osłonową. Na koniec włącz zabezpieczenie obwodu prądowego.
Ustawianie
Aby przejść do trybu testowego, należy ustawić regulator jak na (rys. E). Za pomocą regulatora odległości, czasu i natężenia oświetlenia można przeprowadzić indywidualne ustawienia (rys. E). Za pomocą przesuwnego przełącznika (rys. E) możliwe jest ustawienie dalszych funkcji: OFF = WYŁ: Podczas wymiany żarówki należy zawsze ustawić przełącznik w to położenie PIR = tryb automatyczny: detektor ruchu włącza światło po wykryciu ruchu i ponownie go wyłącza po upływie wybranego czasu – jeżeli nie zostanie zarejestrowany inny ruch
ON = światło ciągłe: odbiornik pozostaje trwale włączony AGON LUX LBM 16934
Jeżeli zmierzona wartość oświetlenia spadnie poniżej zadanej wartości skręca nieco opóźniony światło noc / orientacja zintegrowana LED jeden.
Uwagi dotyczące recyklingu
zapewnienia prawidłowej utylizacji urządzeń. Odpowiednie informacje można uzyskać u odpowiednich władz miejskich lub gminnych.
(
rys.
B2)
. Włóż zasilacz do puszki podtynkowej i
Niniejszego urządzenia nie wolno usuwać razem z niesortowanymi odpadami domowymi. Posiadacze zużytego sprzętu są ustawowo zobowiązani do
Analiza błędów — wskazówki praktyczne
Usterka Przyczyna Rozwiązanie
Czujka ruchu zbyt późno się włącza • Ruch na wprost Montaż wyżej. Ustaw regulator zasięgu na „max.” Nie jest uzyskiwany maksymalny zasięg • Czujka ruchu zamocowana zbyt nisko
Lampa świeci nieprzerwanie lub załącza się w niepożądany sposób
Oświetlenie nie przełącza się • Uszkodzony bezpiecznik
Dane techniczne AGON LUX 16934
Obszar detekcji 160° Napięcie sieciowe 230V ~, 50Hz Zasięg do ok. 8 m Ustawienie czasu ok. 10 s – 7 min, regulowane bezstopniowo temperatura otoczenia ok. -15 °C do +45 °C Moc załączalna maks. 200 W LEDs, maks. 200 W lampy energooszczędne, maks. 500 W żarówki Klasa ochrony II Zalecana wysokość montażu ok. 0,8 m – 1,2 m
Dane techniczne AGON KOMBI 16910
Obszar detekcji 160° Napięcie sieciowe 230V ~, 50Hz Zasięg do ok. 8 m Ustawienie czasu ok. 10 s – 7 min, regulowane bezstopniowo temperatura otoczenia ok. -15 °C do +45 °C Moc załączalna Moc łączeniowa żarówki 40 – 400 W, 40 – 150 W lampa halogenowa na napięcie sieciowe, niskonapięciowe lampy halogenowe 12 V 40 – 150 VA (transformator elektroniczny) Klasa ochrony II Zalecana wysokość montażu ok. 0,8 m – 1,2 m
• Zbyt mała różnica temperatury pomiędzy otoczeniem a źródłem ciepła
• Nieprzerwany ruch ciepła: czujka ruchu została umieszczona nad źródłem ciepła (np. grzejnikiem) lub jest narażona na bezpośrednie lub pośrednie działanie promieni słonecznych
• Uszkodzony element oświetleniowy
• Należy pamiętać, że minimalne obciążenie to 40W
μ = szerokość rozwarcia styków < 1,2 mm
12 13
Zastrzegamy sobie możliwość dokonania niezapowiedzianych zmian technicznych i optycznych.
Montaż wyżej Ustaw regulator zasięgu na „max.”
Wymień bezpiecznik
DEGBFRITPL
1514
Loading...