The content of this information is subject to be changed without notice.
Please contact HANVON or its agent for further information.
□Customer’s Confirmation
By
Date
□HANVON’s Confirmation
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 1 of 15
HANVON PENTECH CO., LTD
Rev.
Issued Date
Revised Contents
1.0
2016-6-8
Preliminary
Revision History
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 2 of 15
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 3 of 15
HANVON PENTECH CO., LTD
Parameter
Specifications
Unit
Note
Sensor
Board
External Dimension
256.73(L)×114.35(W
) ×3.2(H)
mm
±0.2mm(L,W)
±0.05mm(H)
Effective Diagonal Size
10.1
inch
Active Area
217.59(L) ×
136.36(W)
mm
Material
PI
-
Resolution
10206*7422
-
Coordinate Accuracy
±0.5(center)±0.8
(Edge)
mm
Detectable Height
>10
mm Pressure Level
1024
Physical Interface
8 Pins Connectors
Data Sending Rate
>150
dots/s
7Bytes/dot
Response Time
<100
ms
Voltage/Current
3.3V/<60mA
-
USB
1. Scope
This specification is applicable to Hanvon PenTech Electromagnetic Touch
Board designed.
2. Features
Without affecting the screen display
High screen resolution
High pressure levels
High position accuracy
Low power consumption
Commercial temperature range
Support battery-free, cordless and pressure sensitive pens
3. General Specifications
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 4 of 15
HANVON PENTECH CO., LTD
Others
Module Weight
g
TBD
Note:
1、This specification is for standard module. For better performance, it needs
to be customized by customer’s system.
2、Maximum different error in pressure values < 2LSB
3、Maximum Coordinate jitters < 1 point
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 5 of 15
HANVON PENTECH CO., LTD
4. Appearance
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 6 of 15
HANVON PENTECH CO., LTD
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 7 of 15
HANVON PENTECH CO., LTD
5. Mechanical Drawing
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 8 of 15
HANVON PENTECH CO., LTD
NO.
J1(USB)
1
NC
2
USB-
3
USB+
4
PDCT
5
SLEEP
6
NC
7
VCC+3.3V
8
GND
6. Signal Assignment
Note:
1 Logic Low: 0 < UL < 0.2×VDD;
Logic High: VDD-0.3 < UH < VDD.
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 9 of 15
HANVON PENTECH CO., LTD
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Unit
Ground
GND
-
- 0 -
V
Digital Power Supply
VDD
-
-
3.3 - V
I
Vcc
Vcc=3.3V
20
40
60
mA
Sleep Power
SLP
SLP = ‘1’;
Vcc=3.3V
0.10
0.33
0.70
mW
Reset Time
RST
I = 10mA
50
70
100
ms
Sleep Time
SLP
SLP = ‘1’;
Vcc=3.3V
10
20
50
ms
Awake Time
SLP
SLP = ‘0’;
Vcc=3.3V
15
20
50
ms
Power Cycle
-
Vcc=3.3V
50
100
150
ms
7. Electrical Characteristics
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 10 of 15
HANVON PENTECH CO., LTD
8 Pin Connector
Sensor board
Control
Board
8. Idle Mode*
If the board does not find the pen in 5 seconds, the board enters idle mode
(Max. current < 20mA), Support selective suspend mode, followed WHQL 8.0/8.1
Note: The power consumption in Idle mode and performance need to be
defined after the joint debugging.
9. Block Diagram
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 11 of 15
R
pen
=0.9mm
Δ
LCD
Ф
θ
θ X
Pen
Y
HANVON PENTECH CO., LTD
10. Pen Accuracy
Figure 1 R
Figure 2 Ф = 90°, θ = 15°:Δ ≤ 0.5mm
Note 1: If noise exists, Δ will increase.
Note 2: At the edge of the sensor board, Δ≤ 0.8mm.
Note 3: Writing angle(Ф) must be greater than 40 degrees.
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 12 of 15
and Δ
pen
HANVON PENTECH CO., LTD
Figure 3 Center/Edge of the sensor board
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 13 of 15
HANVON PENTECH CO., LTD
Item
Test condition
Criterion
Operating
Environment
(1) High temperature 50℃ 72hrs
(2) High humidity 90%, temperature 60℃ 72hrs
(3) Low temperature 0℃72 hrs
After changing the environment, condition is
brought back to normal (15 - 35℃, 25-75 %( RH).
Another one or more hours later, functional test is
performed.
No
malfunction
Storing
Environment
(1) High temperature 75℃ 72hrs
(2) High humidity 85%, High temperature 75℃
72hrs
(3) Low temperature -10℃ 72hrs
After changing the environment, condition is
brought back to normal (15 - 35℃, 25-75 %( RH).
Another one or more hours later, functional test is
performed.
No
malfunction
Package
Drop
(1) Height : 80cm
(2) Floor surface : Concrete
(3) Number of drops :
A corner of the bottom panel 1
An edge between bottom and end panels 1
An edge between bottom and side panels 1
An edge between side and end panels 1
All six panels 6
Total 10 drops
No
malfunction
Package
Vibration
(1) Z axis : 2G
(2) X and Y axis : 1G
(3) Frequency : 5~200Hz Sweep
No
malfunction
11. Reliability test
( This is for your reference only. The final Reliability test for
TP-101S01-H1S1-GT will be provided after we get final product)
Test Conditions:
1. The Electromagnetic Touch Board should be inspected as regular functional
testing.
2. No condensing of water (moisture) is allowed on the Electromagnetic Touch
Board.
3. For environmental tests, temperature gradient is 15℃/hour.
4. The number for the test samples is 10 units.
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 14 of 15
HANVON PENTECH CO., LTD
12. Labels
12.1 Green Label
Label Material: White color Label Ink: Green
Label Location: Paste on the middle of the board backside
12.2 Bar Code Label
12.3 Shipping Mark Label
TBD
13. Packing
TBD
The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech
Co., Ltd. Page 15 of 15
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.