Getac Technology 042 User Manual

V200
USER’S MANUAL
Rugged Mobile Computing Solutions
Sep. 2010
TRADEMARKS The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. All brand and product names are trademarks or registered trademarks of their respective companies.
NOTE The information in this manual is subject to change without notice. Most screens and operating instructions in this manual are based on Windows 7. If you’re using a different version of Windows, the screens and related operations may not be the same.
For the latest version of the manual, please visit the Getac website at
www.getac.com
.
®
ENERGY STAR
is a government program that offers businesses and consumers energy-efficient solutions, making it easy to save money while protecting the environment for future generations.
Please reference ENERGY STAR
®
related information from
www.energystar.gov.
®
As an ENERGY STAR determined that this product meets the ENERGY STAR
Partner, Getac Technology Corporation has
®
guidelines for
energy efficiency. An ENERGY STAR
®
qualified computer uses 70 % less electricity than
computers without enabled power management features.
Earning the ENERGY STAR®
When every home office is powered by equipment that has earned
the ENERGY STAR greenhouse gases out of the air.
If left inactive, ENERGY STAR
mode and may use 15 watts or less. New chip technologies make power management features more reliable, dependable, and user-friendly than even just a few years ago.
®
, the change will keep over 289 billion pounds of
®
qualified computers enter a low-power
Spending a large portion of time in low-power mode not only saves
energy, but helps equipment run cooler and last longer.
Businesses that use ENERGY STAR
®
enabled office equipment may
realize additional savings on air conditioning and maintenance.
Over its lifetime, ENERGY STAR
®
qualified equipment in a single home office (e.g., computer, monitor, printer, and fax) can save enough electricity to light an entire home for more than 4 years.
Power management (“sleep settings”) on computers and monitors
can result in much savings annually.
Remember, saving energy prevents pollution
Because most computer equipment is left on 24 hours a day, power management features are important for saving energy and are an easy way to reduce air pollution. By using less energy, these products help lower consumers’ utility bills, and prevent greenhouse gas emissions.
Table of Contents
Chapter 1 Getting Started...............................................................1-1
Getting the Computer Running............................................1-2
Unpacking............................................................................1-2
Connecting to AC Power ..................................................1-3
Opening and Closing the Cover......................................1-4
Operating in Tablet Mode.................................................1-5
Turning On and Off the Computer...................................1-8
Taking a Look at the Computer............................................1-9
Front Components..............................................................1-9
Rear Components.............................................................1-11
Right-Side Components...................................................1-12
Left-Side Components......................................................1-12
Top-open Components ...................................................1-14
Bottom Components........................................................1-16
Using the Accessories............................................................1-17
Using the Tether (Optional)..............................................1-17
Attaching the Hand Strap ...............................................1-18
Chapter 2 Operating Your Computer............................................. 2-1
Starting and Stopping the Computer ..................................2-2
Starting the Computer .......................................................2-2
Stopping the Computer.....................................................2-2
Using the Internal Keyboard ..................................................2-4
Typewriter Keys....................................................................2-4
Cursor-Control Keys ............................................................2-4
Numeric Keypad.................................................................2-5
i
Function Keys.......................................................................2-6
Fn Key....................................................................................2-6
Hot Keys ................................................................................2-6
Using the Touchpad................................................................2-8
Configuring the Touchpad..............................................2-10
Navigating on the Screen....................................................2-11
Using the Touchscreen .....................................................2-11
Using Multi-touch Gestures (Windows 7 Only)..............2-12
Using the Dual Mode Display (Optional).......................2-15
Using the Input Panel............................................................2-18
Using OSD Control Panel ......................................................2-19
Using the Fingerprint Scanner (Optional) ..........................2-20
Using the Video Features......................................................2-22
Configuring the Display Modes ......................................2-22
Using Landscape or Portrait View...................................2-23
Using the Audio Features......................................................2-25
Connecting Audio Devices.............................................2-25
Using G-Camera Lite.............................................................2-27
Using the Network Features..................................................2-28
Using the Modem..............................................................2-28
Using the LAN.....................................................................2-29
Using the Wireless LAN......................................................2-29
Using the Bluetooth Feature ................................................2-32
Turning On/Off the Bluetooth Radio ..............................2-32
Connecting to another Bluetooth Device....................2-33
Chapter 3 Managing Power ............................................................3-1
AC Adapter..............................................................................3-2
Battery Pack.............................................................................3-3
Charging the Battery Pack................................................3-3
Checking the Battery Level...............................................3-4
Replacing the Battery Pack ..............................................3-5
Battery Low Signals and Actions.......................................3-6
ii
Power Management ..............................................................3-7
Hibernation...........................................................................3-8
Power-Saving Tips ....................................................................3-9
Chapter 4 Expanding Your Computer............................................ 4-1
Connecting an External Monitor...........................................4-2
Connecting a Serial Device ..................................................4-3
Connecting a USB Device .....................................................4-4
Connecting an eSATA Device ..............................................4-5
Using Smart Cards (Optional)................................................4-6
Using PC Cards.........................................................................4-7
Using ExpressCards (Optional)...............................................4-9
Using the SD Card Reader ...................................................4-11
Using the Port Replicator (Optional)...................................4-12
System Memory Upgrade.....................................................4-13
Chapter 5 Using BIOS Setup and System Recovery....................... 5-1
BIOS Setup ................................................................................5-2
When and How to Use........................................................5-2
Main Menu...........................................................................5-3
Advanced Menu.................................................................5-4
Security Menu......................................................................5-6
Boot Menu............................................................................5-8
Exit Menu ..............................................................................5-9
System Recovery ...................................................................5-10
Chapter 6 Installing Software Drivers and Utilities ......................6-1
How to Use the Driver Disc.....................................................6-2
Installation for Windows XP.....................................................6-3
Drivers on the First Page.....................................................6-3
Drivers on the Second Page .............................................6-4
Installation for Windows Vista ................................................6-7
Drivers on the First Page.....................................................6-7
Drivers on the Second Page .............................................6-8
iii
Drivers on the Third Page ...................................................6-9
Installation for Windows 7.....................................................6-11
Drivers on the First Page...................................................6-11
Drivers on the Second Page ...........................................6-12
Drivers on the Third Page.................................................6-13
Chapter 7 Using Getac Software.....................................................7-1
Using G-Manager ....................................................................7-2
Using Button Manager............................................................7-4
Chapter 8 Caring for the Computer................................................ 8-1
Protecting the Computer.......................................................8-2
Using an Anti-Virus Strategy...............................................8-2
Using Security Center (for Windows V i sta) or Action
Center (for Windows 7).......................................................8-2
Using the Cable Lock .........................................................8-3
Taking Care of the Computer ...............................................8-4
Location Guidelines............................................................8-4
General Guidelines.............................................................8-4
Cleaning Guidelines ...........................................................8-5
Battery Pack Guidelines.....................................................8-5
Touchscreen Guidelines.....................................................8-6
When Traveling ........................................................................8-8
Chapter 9 Troubleshooting............................................................. 9-1
Preliminary Checklist ...............................................................9-2
Solving Common Problems....................................................9-3
Battery Problems .................................................................9-3
Bluetooth Problems.............................................................9-3
Display Problems .................................................................9-4
Hardware Device Problems ..............................................9-5
Hard Disk Drive Problems ...................................................9-5
Keyboard, Mouse, and Touchpad Problems .................9-6
LAN Problems.......................................................................9-6
Modem Problems................................................................9-7
iv
PC Card Problems...............................................................9-7
Power Management Problems.........................................9-7
Software Problems ..............................................................9-8
Sound Problems...................................................................9-9
Startup Problems .................................................................9-9
WLAN Problems .................................................................9-10
Other Problems..................................................................9-11
Resetting the Computer.......................................................9-13
Appendis A Specifications................................................................. A-1
Appendix B Regulatory Information.................................................B-1
On the Use of the System.......................................................B-2
Class B Regulations .............................................................B-2
UL1604 Installation Instructions..........................................B-3
Safety Notices......................................................................B-4
On the Use of the RF Device..................................................B-7
USA and Canada Safety Requirements and Notices...B-7
European Union CE Marking and Compliance NoticesB-10
v
Chapter 1
Getting Started
Congratulations on purchasing this rugged computer. This chapter first tells you step by step how to get the computer up and
running. Then, you will find a section briefly introducing the external components of the computer.
Getting Started 1-1
Getting the Computer Running
This section guides you through the procedures for getting the computer ready for operation.
Unpacking
After unpacking the shipping carton, you should find these standard items:
Notebook computer Accessories:
AC adapter AC power cord Grid-type hand strap Driver disc Document(s) Stylus (option) Digitizer pen and size “AAAA” battery (option) Tether (option)
Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
Keep the shipping carton and packing materials in case you need to ship or store the computer in the future.
1-2
Getting Started
Connecting to AC Power
The computer operates either on the external AC power or internal battery power. It is suggested that you use AC power when you start up the computer for the very first time.
CAUTION: Use only the AC adapter included with your computer. Using other AC adapters may damage the computer.
1. Make sure that the computer is turned off.
2. Plug the DC cord of the AC adapter to the power connector of the computer ().
3. Plug the female end o f the A C pow er cor d to the A C adap ter and the male end to an electrical outlet ().
4. When the AC adapter is connected, power is being supplied from the electrical outlet to the AC adapter and o nto your computer. Now, you are ready to turn on the computer.
Getting Started 1-3
CAUTION:
When you disconnect the AC adapter, disconnect from the electrical outlet
first and then from the computer. A reverse procedure may damage the AC adapter or the computer.
When unplugging the connector, always hold the plug head. Never pull on the
cord.
NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3.
Opening and Closing the Cover
To open the top cover:
1. Pull loose the cover latch () and release the clamp ().
2. Lift up the cover (). You can tilt the cover forward or backward for optimal viewing clarity.
1-4
Getting Started
To close the top cover:
1. Close the display.
2. Lift the cover latch and engage the clamp on the display. Then, push in the cover latch to click it into place.
Operating in Tablet Mode
In addition to being used as a regular notebook computer (Laptop mode), your computer can also be operated in Tablet mode. In Tablet mode, you operate the computer with a stylus or digitizer pen, or a fingertip, instead of a keyboard or mouse.
1. Open the top cover so that it is almost perpendicular with the keyboard of the computer.
2. Turn the display counter-clockwise by 165
o
.
Getting Started 1-5
CAUTION: Do not rotate the display more than 165 display clockwise.
3. Close the computer with the display facing up.
1-6
Getting Started
o
, or attempt to rotate the
4. Lift the cover latch and engage the clamp on the display. Then, push in the cover latch to click it into place.
In Tablet mode, the computer can be operated while holding it as shown.
To return to Laptop mode, perform the steps for changing the computer into Tablet mode in reverse order.
Getting Started 1-7
Turning On and Off the Computer
Turning On
1. Make sure that the computer is connected to AC power.
2. Press the power button (
3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start.
).
Turning Off
To turn off the computer power, use the “Shut Down” command of your operating system.
NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.)
CAUTION: If you have to turn the computer on again immediately after turning it off, wait for at least five seconds. Turning the computer off and on rapidly can damage it.
1-8
Getting Started
Taking a Look at the Computer
NOTE:
Depending on the model you purchased, the appearance of your computer
may not be exactly the same as those shown in this manual.
You need to open the protective covers to access the connectors. When not
using a connector, make sure to close the cover completely for water- and dust-proof integrity. (Engage the locking mechanism if existing.)
Front Components
Ref Component Description
 
Hand Strap Holder
Speaker OSD Control
Button P1
Sunlight­readable
Button
The hand strap can be attached to the two holders for convenient handling of your computer.
Sends out sound and voice from your computer. Opens or closes the OSD (On Screen Display) control
panel. Can be re-defined using the OSD utility. (See “Using
Button Manager” in Chapter 7 for information.) Toggles the sunlight-readable mode ON and OFF.
IMPORTANT: To prevent burns to your fingers if using the computer (especially in Tablet Mode) with sunlight-readable mode turned on, do wear gloves when touching the top portion of the LCD display as it may be hot to the touch.
Getting Started 1-9
Ref Component Description
P2
RF Button
P3
Reset Button
P4
Software
Keyboard Button
P5
Top Cover
Latch Power Button
Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.)
Toggles the wireless LAN /Bluetooth/3G radio frequency ON and OFF.
Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.)
Serves as the Ctrl+Alt+Del keyboard keys.
Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.)
Opens or closes the software keyboard on your screen.
Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.)
Locks the to p cover.
Turns the computer power ON and OFF.
1-10
Getting Started
Rear Components
Ref Component Description
Hand Strap Holder
Audio Output
Connector Microphone
Connector USB Port
Kensington Lock
VGA Connector
Serial Connector
The hand s trap can be attach ed to th e two ho lders for convenient handling of your computer.
Connects a set of headphones, external speakers with amplifier, or an audio recording device.
Connects an external microphone.
Connects a USB device, such as a flash disk, printer, digital camera, joystick, and mo re.
Locks the computer to a stationary object for security.
Connects an external display monitor. NOTE: Depending on your model, this port could be
a serial connector. Connects a serial mouse or serial communication
device.
Getting Started 1-11
Right-Side Components
Ref Component Description
Battery Pack
Compartment
Hard Disk Drive
Compartment
Inside is the battery pack that supplies power to your computer when external power is not connected.
Inside is the hard disk drive.
Left-Side Components
1-12
Getting Started
Ref Component Description
Power Connector
USB Port
eSATA/USB Combo
Port
RJ-11 Connector
RJ-45 Connector
Can be one of the below depending on your model:
ExpressCard Slot PCMCIA Slot
Can be one of the below depending on your model:
Smart Card Reader
PCMCIA Slot SD Card Reader
Connects the AC adapter. Connects a USB device, such as a flash disk,
printer, digital camera, joystick, and more. Connects an eSATA device such as an external
hard drive or optical drive. Can also function as a USB port. Connects the telephone line.
Connects the LAN cable.
Accepts an ExpressCard for additional functions. Accepts a PC card for additional functions.
Accepts a smart card for additional security feature.
Accepts a PC card for additional functions. Accepts a SD (Secure Digital) card for removable
storage media.
Getting Started 1-13
Top-open Components
Ref Component Description
  
 
1-14
Webcam Lens (option)
LCD Screen
Light Sensor
Fingerprint Scanner (option)
Keyboard
Getting Started
Allows you to use your computer’s camera function. The camera lens can be rotated.
Displays the output of the computer. May include the optional touchscreen feature.
Detects the surrounding lighting condition for automatic adjustment of the LCD brightness and optional keyboard backlight.
Uses fingerprint verification to protect your computer against unauthorized access.
Serves as the data input d evice.
Ref Component Description
Indicators
Charge
Drive In-Use
Power
Battery
Hard Disk
RF
Num Lock Caps Lock
Show the current status of the computer’s devices. Lights green when the computer is turned on. Lights yellow when the computer is in Sleep mode. Lights green when the battery is fully charged. Lights yellow when the battery is being charged. Blinks yel low wh en th e ba tter y’ s ca pa ci ty i s b elo w
10%. Blinks green and yellow by turns to indicate
charging is suspended because the battery’s temperature is either too high or too low.
Lights green when the computer is accessing the hard disk drive.
Blinks red when the optional hard disk drive heater is on for low temperature operation.
Lights when the wireless LAN/Bluetooth/3G radio frequency is on.
Lights when Num Lock is on. Lights when Caps Lock is on.
Stylus/Digitizer
Pen (option) Touchpad
Serves as the input device by tapping on the screen to make selections and enter information.
Serves as the pointing device.
Getting Started 1-15
Bottom Components
Ref Component Description
 
1-16
Expansion Bus Connector
Memory Slots
Getting Started
Inside is the expansion bus connector for using the Port Replicator option.
Inside are the memory slots for expanding the memory size of your computer.
Using the Accessories
Using the Tether (Optional)
A tether is provided for attaching the stylus to your computer.
1. Insert one of the tether’s loop ends through the hole of the stylus (as indicated by below). Then, insert the other end through the first loop (as indicated by below) and pull it tight.
2. Insert the other loop end to the tether hole on the computer (as indicated by below). Then, insert the stylus end through the loop (as indicated by below) and pull it tight.
Getting Started 1-17
Attaching the Hand Strap
The hand strap can be attached to any side of your computer. To use the hand strap, secure the snap hooks to the holders on your computer.
CAUTION:
The strap has been designed to carry only the weight of the computer.
Therefore, be sure that the strap does not carry a weight that exceeds the weight of the computer. The strap may accidentally come loose from the computer.
Do not use a strap that is damaged or about to tear.
1-18
Getting Started
Getting Started 1-19
Chapter 2
Operating Your Computer
This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the
operating basics. If you are already a computer user, you may choose to read only the parts containing information unique to your computer.
CAUTION: The computer can get uncomfortably warm when you use it in high temperatures. As a safety precaution in such a circumstance, do not place the computer on your lap or touch it with your bare hands for extended periods of time. Prolonged body contact can cause discomfort and potentially a burn.
Operating Your Computer 2-1
Starting and Stopping the Computer
There are a number of ways to start and stop the computer.
Starting the Computer
You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the
storage device such as the hard disk. The computer will automatically load the OS after you turn it on. This process is called booting.
NOTE: An operating system is the platform for all your software application programs to run on. Your computer uses the Microsoft Windows operating system.
Stopping the Computer
When you finish a working session, you can stop the computer by turning off the power or leaving the computer in Standby/Sleep or Hibernation mode:
To stop in this
mode...
Off Follow the shutdown procedure of
your operating system. This can prevent loss of unsaved data or damage to your software programs.
If the system is locked up because of hardware or software problems, press the power bu tton to turn of f the computer.
Standby/Sleep Depending on your settings in
Windows, you can place the
2-2
Operating Your Computer
Do this... To start up or
resume again
Press the power button.
Press any key.
To stop in this
mode...
Do this... To start up or
resume again
computer in Standby/Sleep mode by:
Closing the display cover Pressing the Fn+F12 hot key Pressing the power button
Hibernation Depending on your settings in
Windows, you can place the
Press the power button.
computer in Hibernation mode by:
Closing the display cover Pressing the Fn+F12 hot key Pressing the power button
If you choose to stop in Standby/Sleep or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.)
Operating Your Computer 2-3
Using the Internal Keyboard
Your keyboard has all the standard functions of a full-sized computer keyboard plus an Fn key added for specific functions.
The standard functions of the keyboard can be further divided into four major categories:
Typewriter keys Cursor-control keys Numeric keys Function keys
Typewriter Keys
Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes. When the lock keys (Caps Lock and Num Lk) are pressed, their corresponding indicators light up.
The Control (Ctrl) / Alternate (Alt) key is normally used in combination with other keys for program-specific functions. The Escape (Esc) key is usually used for stopping a process. Examples are exiting a program and canceling a command. The function depends on the program you are using.
Cursor-Control Keys
Cursor-control keys are generally used for moving and editing purposes.
NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.
2-4
Operating Your Computer
Numeric Keypad
A 15-key numeric keypad is embedded in the typewriter keys as shown next:
Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals.
NOTE:
When the numeric keypad is activated and you need to type the English letter
in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off.
Some software may not be able to use the numeric keypad on the computer.
If so, use the numeric keypad on an external keyboard instead.
Operating Your Computer 2-5
Function Keys
On the top row of the keys are the function keys: F1 to F12. Function keys are multi-purpose keys that perform functions defined by individual programs.
Fn Key
The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” a nd the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key.
Hot Keys
Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way. Each time a hot key combination is pressed, it shifts the corresponding function to the other or next choice.
You can easi ly iden tify th e hot ke ys with the ico ns imp rinted on the key top. The hot keys are described next.
Key Description
Switches the keyboard backlight on and off (optional).
Switches the wireless radio on and off.
Decreases the sound volume.
Increases the sound volume.
2-6
Operating Your Computer
Key Description
Switches the display output when external devices are connected. NOTE: This function only applies to Plug & Play display devices.
Decreases the LCD brightness (20 levels).
Increases the LCD brightness (20 levels).
Switches the touchscreen on and off (option).
Switches the touchpad on and off.
Switches the system sound output off (mute) and on.
Switches LCD backlight on and off.
Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.)
Windows Keys
The keyboard has two keys that perform Windows-specific functions: Windows Logo key and
The software-specific functions when used in combination with other keys. The
your Windows manual for more information.)
Windows Logo key opens the Start menu and performs
Application key usually has the same effect as a right mouse click. (See
Application key.
Operating Your Computer 2-7
Using the Touchpad
CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface.
NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force.
The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
The touchpad consists of a rectangular pad (work surface) and a left and right buttons. To use th e touchpad, place your forefinger or thu mb on the pad. The rectangular pad acts like a miniature duplicate of your display. As you slide your fingertip across the pad, the pointer (also called cursor) on the screen moves accordingly. When your finger reaches the edge of the pad, simply relocate yourself by lifting the finger and placing it on the other side of the pad.
Here are some common terms that you should know when using the touchpad:
2-8
Operating Your Computer
Term Action
Point Move your f i n ger on the pad u n til the cursor p o ints to the
selection on the screen.
Click Press and release the left button.
–or– Tap gently anywhere on the pad.
Double-click Press and release the left button twice in quick
succession. –or– Tap twice on the pad rapidly.
Drag and drop
Press and hold the lef t button , the n move yo ur fi nger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
–or– Gently tap twice on the pad an d on the second tap,
keep your finger in contact with the pad. Then, move your fing er ac ro ss the p ad to d rag the s elec ted o bj ect to your destination. When you lift your finger from the pad, the selected object will drop into place.
Scroll To scroll is to move up and down or left and right in the
working area on the screen. To move vertically, place your finger on the right or left
edge of the pad and slide your finger up and down along the edge. To move horizontally, place your finger on the top or bottom edge of the pad and slide your finger left and right.
This function works only a fter you install the touchpad driver supplied with the computer and it may not work for all applications.
Operating Your Computer 2-9
TABLE NOTE: If you swap the left and right buttons, “tapping” on the touchpad as an alternative method of press ing the left button will no longer be valid.
Configuring the Touchpad
You may wan t to c on fi gur e th e tou chp ad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vice versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on.
To configure the touchpad, go to Control Panel Mouse Properties.
2-10
Operating Your Computer
Navigating on the Screen
The screen of your computer is touch-sensitive. You can control the location of the cursor/pointer on the screen using your finger or the included stylus or digitizer pen to communicate with the computer.
CAUTION: Do not use sharp objects on the LCD display. Doing so may damage the display surface. Use your finger or the included stylus or digitizer pen.
NOTE: When there is a noticeable discrepancy in the placement of the stylus on the screen and the indicated position of the onscreen pointer, calibrate the touchscreen using the calibration utility called IdeaCom Calibration on Windows XP/Vista or CalTouch on Windows 7.
Using the Touchscreen
If your computer is equipped with the touchscreen feature, you can use your finger or the included stylus to navigate and select objects on the screen.
Operating Your Computer 2-11
Here are some common terms that you should know when using the touchscreen:
Term Action
Click/Point Tap gently on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and
drop
Tap lightly on the touchscree n and move your finger until you reach your destination (drag). Finally, release your finger (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Using Multi-touch Gestures (Windows 7 Only)
If your computer model comes with multi-touch-capable screen and Windows 7, you can interact with your computer by placing two fingers on the screen. The movement of the fingers across the screen creates “gestures,” which send commands to the computer.
Here are the multi-touch gestures that you can use:
Gestures Actions
( = finger down; = finger up)
Pan (Scroll)
or
Descriptions
Use panning to see another part of a page that has scroll bars.
2-12
Operating Your Computer
Drag 1 or 2 fingers up or down.
Gestures Actions
( = finger down; = finger up)
Zoom (Pinch)
Move two fi ngers apart/toward each other.
Rotate
or
Move two fingers in opposing directions.
-or­Use one finger to pivot around
another.
Press and Tap
Descriptions
Use zooming to make an item (a photo for example) on the screen larger or smalle r . The gesture works in applications that support mouse wheel zooming.
Use rotating to move a picture or other item on the screen in a circular direction (clockwise or counter­clockwise). The gesture works in applications that support the specific gesture.
Use press and tap to access the shortcut menu.
Press on target and tap using a second finger.
Operating Your Computer 2-13
Gestures Actions
( = finger down; = finger up)
Two­finger Tap
Tap two fingers at the same time (where the target is in the midpoint between the fingers).
Flicks
Make quick drag gestures in the desired direction.
Descriptions
The function is defined by applications that support the specific gesture.
Flick left or right to navigate back and forward in a browser and other applications. The gesture works in most applications that support back and forward.
2-14
Operating Your Computer
Using the Dual Mode Display (Optional)
Dual mode display incorporates both touchscreen and digitizer functions. The display is set to Touchscreen mode by default. Touchscreen mode
provides all the functionalities that an ordinary touchscreen has. When the computer receives signals from the active digitizer pen, the display automatically switches to Digitizer mode.
When using the digitizer pen, be sure to install the included size “AAAA” battery.
Here are some common terms that you should know when using the active dig itizer feature:
Term Action
Wake up The digitizer pen automatically enters
Sleep mode after 30 seconds of inactivity . T o s ta rt u si n g th e p en , tap the tip of the pe n to activate i t .
Operating Your Computer 2-15
Term Action
Move
Click/Point
Double-clic k
Drag and drop
Right-click
Move the curs o r p o i nte d by the di g iti z er pen.
Tap gently on the display.
Tap twice on th e display rap idly.
Tap lightly on the display and m ove your digitizer pen until you reach your destination (drag). Fi nally, release your digitizer pen (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Press and hold down the digitizer pen button (A ), then tap gently the objec t.
CAUTION:
When the LCD display is used alone or with an external display
simultaneously, the digitizer function cannot be used when the area of either display is set larger than the default setting of the display resolution.
Even when only an external display is in use, the cursor will move on the
external display if you touch the surface of the LCD display with the pen or bring the pen close to the surface of the LCD display when the digitizer driver is active. Therefore, do not touch the LCD display when only an external display is in use.
The active digitizer feature cannot be used in the BIOS Setup program or
when using the full screen in DOS mode.
2-16
Operating Your Computer
NOTE:
You can move the cursor by bringing the digitizer pen close to the screen,
without actually touching the screen’s surface.
Do not move the digitizer pen too quickly. If the pen moves too quickly, the
cursor may be unable to follow its movement.
If you cannot click on the edge of the screen, hold the digitizer pen
perpendicular to the display and try clicking again.
Operating Your Computer 2-17
Using the Input Panel
Use the Input Panel to enter text and perform various keyboard functions. There are two types of Input Panels for you to use in Windows 7:
Touch Keyboard allows you to enter text by tapping the keys with your
stylus, like pressing the keys on a standard keyboard.
Writing Pad allows you to write on the writing pad, like writing on a piece
of paper. Your handwriting will be converted into typed text.
To open the Input Panel, tap the Input Panel tab, which appears by default on the left edge of the screen. (You can also press the on the front of the computer to open or close the Input Panel.) To switch between the two types, tap Input Panel.
NOTE: For more information on using the Input Panel, see Windows’ online help.
2-18
Operating Your Computer
or at the upper left corner of the
button
Using OSD Control Panel
The OSD Control Panel allows you to easily activate or operate certain functions on your computer.
To use the OSD Control Panel:
1. Press the button
2. The following screen appears, providing several control buttons.
For detailed descriptions of the Control Panel, click the
3. To close the Control Panel, either press the button computer again or click the
on the front of your computer.
button .
on your
button.
Operating Your Computer 2-19
Using the Fingerprint Scanner (Optional)
The fingerprint scanner provides a strong authentication mechanism based on fingerprint recognition. You can log on to your computer or sign in to a web site with your fingerprint instead of a password. You can also encrypt files and folders with your fingerprint.
NOTE: You can register a fingerprint only after creating a password for the Windows user account.
CAUTION: For the fingerprint file/folder encryption feature, the maximum file/folder size allowed is 2GB.
To register your fingerprint, click Start All Programs Fingerprint Software Fingerprint Registration. Click the finger you want to register and follow the
onscreen instructions to complete.
2-20
Operating Your Computer
You can then use the Fingerprint Software to set up h ow the fingerprint authentication works.
For detailed information, click Start All Programs Fingerprint Software Help.
Operating Your Computer 2-21
Using the Video Features
The video subsystem of your computer features:
12.1-inch wide TFT (Thin-Film Transistor) color LCD display with 1200×800
WXGA resolution
Simultaneous display on LCD and external monitor Multi-display capability
Built-in lig ht sensor to automatically adj ust the LCD brig htness and optional keyboard backlight
Power Management Sunlight-readable LCD display
NOTE: The computer enters the Standby/Sleep or Hibernation mode when the LCD is closed. If you want to use the computer with the LCD closed, set according in Windows Control Panel so the computer does not enter the Standby/Sleep or Hibernation mode when the LCD is closed.
Configuring the Display Modes
NOTE: When using an external CRT monitor, the resolution depends on the CRT monitor’s supported resolution.
Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information.
For displaying in higher resolutions, you can connect an external monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.)
2-22
Operating Your Computer
Using Landscape or Portrait View
After Windows is started up, you can rotate the display and perform the touchscreen and active digitizer operations in the rotated mode.
To rotate the display, press the button computer to open the OSD control panel and click
located on the front of your
. Each
time this Rotate button is clicked, the screen disp lay rotates
O
counter-clockwise by 90
.
NOTE:
If the screen display resolution has been set to 800×600 pixels, you can rotate
the display to Primary Landscape and Secondary Landscape only.
While the display is rotated:
– Do not set the display resolution larger than the resolution of the LCD display. – If you exit Windows, the next time Windows is started up, the operation of the touchpad will not match the display angle for a few seconds. – The computer’s performance will decrease slightly. – If a video is played, the picture may not be displayed properly or the sound may be broken up. This problem can be corrected by rotating the display to Primary Landscape. – The touchpad’s scroll function does not work.
The display cannot be rotated when DOS mode is set to “Full Screen.”
For a Model without 3G Module
Primary
Landscape
Primary Portrait
Secondary
Landscape
Secondary
Portrait
Primary
Landscape
Display
Display
Display
Display Display
Operating Your Computer 2-23
For a Model with 3G Module
Primary
Landscape
Display
Primary Portrait Secondary
Display
Landscape
Display
Primary
Landscape
Display
2-24
Operating Your Computer
Using the Audio Features
NOTE: If you experience interference while recording, try lowering the microphone recording volume.
The audio subsystem of your computer features:
Built-in sound system for recording and playing sound on your
computer
Azalia interface (high density audio codec) Built-in Speaker External audio connectors
Ways of playing and recording sound vary with the operating system used. See your operating system documentation or online help for specific information.
Connecting Audio Devices
For higher audio quality, you can send or receive sound through external audio devices.
NOTE: After connecting an external audio device, make sure that you specify the use of the correct audio device in Windows.
Operating Your Computer 2-25
Audio Output Connector ( headphones, or earphone set.
) can be connected to speakers,
Microphone Connector (
) can be connected to an external
microphone for recording voice or sound.
NOTE: When using the external speakers/headphones or microphone, you cannot use the internal one.
2-26
Operating Your Computer
Using G-Camera Lite
G-Camera Lite allows you to take pictures with the Web cam, if supplied with
your computer. To start G-Camera Lite, click Start All Prog rams G-Camera Lite G-Camera
Lite. The camera control panel appears.
Mode
Current settings
Setting buttons for different modes
Click the Shutter button
For detailed descriptions of G-Camera Lite, click the button
or press Enter to take photo s.
Operating Your Computer 2-27
.
Using the Network Features
Using the Modem
The internal 56 K fax/data modem allows you to use the telephone li ne to communicate with others by fax, email, or connect to an online service or bulletin board.
To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.
NOTE:
When using the communication software, you may have to disable power
management.
Set parameters such as modem speed (baud rate) and line type (pulse dialing
or tone dialing).
Do not enter the Standby/Sleep mode when using the communication
software.
2-28
Operating Your Computer
Using the LAN
The internal 10/100/1000Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps.
To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN
Depending on your model, an internal mini PCI-E wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment.
The WLAN features include:
Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes
support
WEP (Wired Equivalent Privacy) 64/128-bit data encryption IEEE 802.11a/g/n standard compliance
Operating Your Computer 2-29
Technology 802.11a 802.11g 802.11n
Stated Maximum Throughput (Mbps)
Data Rates (Mbps) 54, 48, 36, 24, 18,
Band (GHz) 5.15 ~ 5.35 2.4 2.4 / 5 Modulation
Technology
54 54 100 Mbps or more
54, 36, 18, 9 100 ~ 210
12, 9, 6
OFDM (Orthogonal Frequency Division Multiplexing)
OFDM (Orthogonal Frequency Division Multiplexing)
Spatial multiplexing, uses MIMO (multiple­input multiple­output)
To take advantage of the WLAN feature, make sure that the WLAN driver is installed correctly. If your WLAN card was provided by your dealer instead of the computer manufacturer, contact your dealer for the correct driver to use.
Turning On/Off the WLAN Radio
NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to turn off wireless LAN when using your computer in the airplane.
1. Press Fn+F1 to turn on or off the wireless radio. The to indicate the wireless radio is on.
indicator lights up
2. Windows Mobility Center has wireless network turned on by default. The Wireless Network icon
on the taskbar should appear without a red X. (In case you have previously turned it off in Windows Mobility Center, be sure to turn it on when using the function the next time.)
2-30
Operating Your Computer
Connecting to a Wireless Network
To connect to a wireless network:
1. Make sure that the WLAN radio is on (as described in the previous section).
2. Tap the Wireless Network icon the icon
indicates connections are available.)
on the taskbar. (An o range light in
3. In the list of available wireless networks, tap a network, and then tap Connect.
4. Some networks require a network security key or passphrase. To connect to one of those networks, ask your network administrator or Internet service provider (ISP) for the security key or passphrase.
For more information on setting a wireless network connection, refer to Windows online help.
NOTE: You can use Intel® PROSet Wireless to take full advantage of the WiFi capabilities of your computer. See the Help of the utility for instructions.
Operating Your Computer 2-31
Using the Bluetooth Feature
Your computer incorporates the Bluetooth capability for short-range (about 10 meters) wireless communications between devices without requiring a cable connection.
With Bluetooth, da ta can be transmitted through walls, pockets and briefcases as long as two devices are within range.
Turning On/Off the Bluetooth Radio
1. Press Fn+F1 to turn on or off the wireless radio. The to indicate the wireless radio is on.
2. The Bluetooth function is enabled by de fault, as indicated by the Bluetooth icon previously disabled the function in the Bluetooth utility, be sure to enable it when using the function the next time.).
The status of the Bluetooth connection is indicated by the Bluetooth icon located in the taskbar. (You need to tap
hidden icons.)
on the Windows taskbar. (In case you have
on the taskbar to show the
indicator lights up
Status Icon
Off On Connected
You can use the Bluetooth Utility to configure Bluetooth wireless connection settings and transfer files.
(blue with red logo)
(blue with white logo).
(blue with green logo)
2-32
Operating Your Computer
Connecting to another Bluetooth Device
1. Make sure that the Bluetooth function is enabled (as described
above).
2. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.)
3. Start the Bluetooth utility by double-clicking the Bluetooth icon the taskbar and click New Connection.
4. The Add New Connection Wizard window appears. Select Express Mode (Recommended), and then click Next.
on
Operating Your Computer 2-33
5. Select the device to connect to and click Next.
6. Dependin g o n the typ e o f B lueto oth de vic e tha t yo u w an t to c onn ec t to, you will need to enter the pertinent information.
For detailed information on using the Bluetooth Utility, see the Bluetooth Utility Help.
2-34
Operating Your Computer
Chapter 3
Managing Power
Your computer operates either on external AC power or on internal battery power.
This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
Managing Power 3-1
AC Adapter
CAUTION:
The AC adapter is designed for use with your computer only. Connecting the
AC adapter to another device can damage the adapter.
The AC power cord supplied with your computer is for use in the country
where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord.
When you disconnect the AC adapter, disconnect from the electrical outlet
first and then from the computer. A reverse procedure may damage the AC adapter or computer.
When unplugging the connector, always hold the plug head. Never pull on the
cord.
The AC adapter serves as a converter from AC (Alternating Current) to DC (Direct Current) power because your computer runs on DC power, but an electrical outlet usually provides AC power. It also charges the battery pack when connected to AC power.
The adapter operates on any voltage in the range of 100~240 V AC.
3-2
Managing Power
Battery Pack
The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter.
The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time.
NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
Charging the Battery Pack
NOTE:
Charging will not start if the battery’s temperature is above 50C (122F) or
below -2C (28F); and the charging process will stop if the battery’s temperature gets above 60C (140 F) or below -2C (28F). The Battery Charge Indicator flashes green and yellow by turns to inform you of such situation. To avoid damaging the battery, disconnect the AC adapter and wait for the battery to return to room temperature before charging again.
During charging, do not disconnect the AC adapter before the battery has
been fully charged; otherwise you will get a prematurely charged battery.
To charge the battery pack, connect the AC ad apter to the computer and an electrical outlet. The Battery Charge Indicator ( computer glows yellow to indicate that charging is in progress. You are advised to keep the computer power off while the battery is being charged. When the battery is fully charged, the Battery Charge Indicator is off.
) on the
It takes approx ima tely 3 hour s to f ully c harg e the Li -Ion batter y pac k when the computer is off, and approximately 6 hours to fully charge the Li-Ion battery pack when the computer is on.
Managing Power 3-3
CAUTION: After the computer has been fully recharged, do not immediately disconnect and reconnect the AC adapter to charge it again. Doing so may damage the battery.
NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer.
Checking the Battery Level
NOTE: Any battery level indication is an estimated result. The actual operating time can be different from the estimated time, depending on how you are using the computer.
By Operating System
You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the battery icon on the taskbar.
By Gas Gauge
On the exterior side of the battery pack is a gas gauge for displaying the estimated battery charge. When the battery pack is not installed in the computer and you want to know the battery charge, you can press the switch with a pointed device to see the corresponding value of indicator segment that lig ht green.
Switch
3-4
Managing Power
The value of the corresponding green segment indicates the relative percentage of the battery charge. The battery pack is fully discharged when you see no segment glowing green.
Replacing the Battery Pack
CAUTION:
There is danger of explosion if the battery is incorrectly replaced. Replace the
battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions.
Do not attempt to disassemble the battery pack.
If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup.
To replace the battery pack, follow these steps:
1. Make sure that the computer is not turned on or connected to AC power.
2. Locate the battery compartment on the right side of the computer.
3. Slide the door lock toward the left to unlock ( latch downward to open the door(
4. Pull on the ribbon strip to remove the battery pack.
).
). Then slide the door
Managing Power 3-5
5. With the rib bon s trip fac ing outw ard , s lid e the n ew batte ry pa ck all the way into the slot.
6. Close the door. Make sure the door latch clicks into place. Then, slide the door lock toward the right.
Battery Low Signals and Actions
When th e batte ry i s low, W i ndow s gi ves war ning messa ges a nd the Batter y Charge Indicator (
Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer. If you are using the audio sub s ys tem , PC card , hard or U S B f la sh d i sk , th e b a tter y mi g ht r un o ut of charge very quickly.
Always re s p o n d to Battery Low by conne c ting the AC adapter, turning off the computer, or placing your computer in Hibernation mode. If you do not take any action, the computer will automatically hibernate and turn off.
) blinks yellow to alert you.
NOTE: You can set up the threshold of Battery Low and actions for Windows to take with Windows Power Options. (For more information, see Windows’ Help.)
3-6
Managing Power
Power Management
Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving.
With an ACPI-compliant operating system such as Windows, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
In general, Windows’ power management works in this way:
What... When...
Power to the hard disk is turned off
Power to the display is turned off When the display has been idle for a
The computer enters the Standby/Sleep mode. The hard disk and display are turned off and the entire system consumes less power.
The computer enters the Hibernation mode. (See the next subsection for more information.)
For detailed information on power management, see Windows’ Help.
When the hard disk has been idle fo r a set period.
set period. When the entire system has been idle
for a set period. When you manually activate the
mode.
When the entire system has been idle for a set period.
When you manually activate the mode.
Managing Power 3-7
Hibernation
Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some tim e to get all these applications open and running, and normally they all have to be closed before the computer can be turned off.
When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shuts down. The next time you turn on your computer, you return to exactly where you left off.
3-8
Managing Power
Power-Saving Tips
Aside from enabling your computer’s power saving mode (see previous section), you can do your part to maximize the battery’s ope rating time by following these suggestions.
Do not disable Power Management. Decrease the LCD brightness to the lowest comfortable level. Shorten the length of time before Wi ndows turn off the display. Many USB devices use power just by being connected. If you use a
USB mouse, you can save power by disconnecting the mouse and using the touchpad. If you use a USB flash drive, unplug it when you are not using it.
If you work with an application that uses a PC card, exit the
application when you finish using it.
If you have a PC card installed, remove it when not in use. Some PC
cards drain power even while they are inactive.
Turn off the wireless radio if you are not using the wireless module. Turn off the computer when you are not using it.
Managing Power 3-9
Chapter 4
Expanding Your Computer
You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in thi s chapter.
Expanding Your Computer 4-1
Connecting an External Monitor
If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your com puter. Follow this procedure to connect an external monitor:
1. Make sure that the computer is not turned on.
2. Plug the monitor’s D-type signal connector to the computer’s VGA connector.
3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet.
4. To use the monitor, turn on the monitor before turning on the computer.
5. The monitor should respond by default. If not, you can switch the display to th e monitor or to both (simultaneous display), or to multi-display by pressing the Fn+F5 hot key. In Windows, you can also change the display through the settings in Display Properties.
6. You can change display settings through your operating system. See your operating system documentation or online help for specific information.
CAUTION: Do not disconnect the external monitor while the computer is in the Standby/Sleep mode or Hibernation mode. If no external monitor is connected when the computer resumes, the LCD might not display properly.
4-2
Expanding Your Computer
Connecting a Serial Device
Your computer has one or two serial port (depending on model) for connecting a serial device such as a serial mouse or serial communication device (modem).
Follow this procedure to connect a serial device:
1. Make sure the computer is not turned on
2. Plug the device cable to the serial port on the rear of the computer.
3. Turn on the computer.
NOTE: Portable modems that derive power through the serial port cannot be used with the computer. Instead, use a modem that is powered by its own internal battery or external AC power.
Expanding Your Computer 4-3
Connecting a USB Device
Your computer has two USB ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse.
NOTE: The eSATA/USB Combo port can also function as a USB port.
The USB port support transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices.
To connect a USB device, simply plug the device cable to one of the USB ports.
4-4
Expanding Your Computer
Connecting an eSATA Device
Your computer has an eSATA/USB Combo port for connecting eSATA devices (such as an external hard drive and external optical drive) / USB devices (see previous section).
The port supports SATA II with transfer rate up to 3.0Gbit/s. It can provide 5V power if a certified USB-eSata combo cable is used.
To connect an external eSATA device, simply plug the d evice c able to th e eSATA port.
Expanding Your Computer 4-5
Using Smart Cards (Optional)
Your computer may have a smart card reader. With an embedded microcontroller, smart cards have the unique ability
to store large amounts of data, carry out their own on-card functions (e.g., encryption and mutual authentication), and inter act intelligently with a smart card reader.
To insert a smart card:
1. Locate the smart card sl ot (the on e without the ej ect button).
2. Slide the smart card, with its label and embedded computer chip facing up into the slot.
3. When a new card is seated, use the third-party smart card software to allow your computer to read it.
To remove a smart card:
1. Make sure th at the th ird -par ty sm art ca rd s oftw are i s not a cces sing the smart card.
2. Pull the card out of the slot.
4-6
Expanding Your Computer
Using PC Cards
NOTE:
Some PC cards require additional system resources. Before using such PC
card, you may have to free other system resources for the PC card.
Although some PC cards can be inserted and removed without turning off the
computer, you cannot remove or install PC cards during Sleep/Standby mode.
Your computer has one or two PC card slots that support CardBus specifications. The slots can accommodate a type II card. Typical type II cards are flash memory, SRAM, modem, LAN, and SCSI cards.
To insert a PC card:
1. Locate the PC card slot on the left side of the computer.
2. Slide the PC card, with i ts label facing up, into the slot until the eject button pops out.
Eject button
3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the pro cess.
To remove a PC card:
1. Double-click on the Safely Remove Hardware icon ( Vista/Windows 7 or and the Safely Remove Hardware window appears on screen.
for Windows XP) found on the Windows taskbar
for Windows
Expanding Your Computer 4-7
2. Select (highlight) the PC card from the list to disable the card.
3. Push the eject button and the card will slide out sl ightly.
4. Pull the card out of the slot.
4-8
Expanding Your Computer
Using ExpressCards (Optional)
NOTE: The ExpressCard interface is not compatible with the PC card interface.
Your computer may have an ExpressCard slot. ExpressCard supports the PCI Express and USB 2.0 serial data interfaces
(supporting speeds of up to 2.5 Gbps and 480 Mbps respectively), improving speed in data transfer while conserving power usage.
The ExpressCard slot can accommodate a 54 mm (ExpressCard/54) or 34 mm (ExpressCard/34) wide ExpressCard. Typical ExpressCards support a very extensive range of applications including memory, wired and wireless communication cards, and security devices.
Shown next are the appearances of ExpressCards for your reference.
ExpressCard/54 ExpressCard/34
To insert an ExpressCard:
1. Locate the ExpressCard slot on the left side of the computer (the upper one).
Expanding Your Computer 4-9
2. Slide the ExpressCard, with its label facing up, all the way into the slot until the rear connectors click into place.
Eject button
3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the pro cess.
To remove an ExpressCard:
1. Double-click on the Safely Remove Hardware icon ( Vista/Windows 7 or
for Windows XP) found on the Windows taskbar
for Windows
and the Safely Remove Hardware window appears on screen.
2. Select (highlight) the ExpressCard from the list to disable the card.
3. Push the eject button and the card will slide out sl ightly.
4. Pull the card out of the slot.
4-10
Expanding Your Computer
Using the SD Card Reader
NOTE:
If your hard disk is divided into several drives, make sure that all drives have
been formatted before using the Card Reader. Otherwise, you may encounter problems when using the Card Reader.
You can use only storage cards. Your Card Reader does not support cards
with I/O (input/output) functions such as a wireless network card or Bluetooth card.
Your computer has a Card Reader. The Card Reader is a small drive for reading from and writing to removable storage cards (or called memory cards). The Card Reader supports Secure Digital (SD) cards.
To insert a storage card:
1. Locate the Card Reader slot on the left side of the computer.
2. Align the card with its connector pointing to the slot and its label facing up. Slide the card into the slot until it reaches the end.
3. Windows will detect the card and assign it a drive name.
To remove a storage card:
1. Double-click My Computer.
2. Right-cli ck the drive wi th the card and select Eject.
3. Push the card to release and then pull the card out of the slot.
Expanding Your Computer 4-11
Using the Port Replicator (Optional)
NOTE: To use the port replicator, the Vehicle Dock driver supplied with your computer must be installed.
A port replicator is available as an option. This device eliminates the hassles of having you connect and disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector at the botto m of yo ur computer.
1. Slide open the expansion bus connector cover.
2. Connect your port replicator to the expansion bus connector.
For more detailed information, refer to the instructions supplied with the port replicator.
4-12
Expanding Your Computer
System Memory Upgrade
You can upgrade your computer by changing system memory to a maximum of 8 GB on the DDR3 SO-DIMM slot.
CAUTION: RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. When inserting or removing a RAM module, do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter. Doing so has been known to cause damage, fire, or electrical shock.
To install the RAM module:
1. Remove the battery pack (see chapter 3) and make sure that the computer is not connected to AC power.
2. Carefully place the computer upside down.
3. Remove the four screws to open the compartment cover.
Expanding Your Computer 4-13
4. To install the RAM module, match the module's n otched part with the socket's projected part and firmly insert the module into the socket at a 20-degree angle. Then push down until the retaining clips lock the module into position.
CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force it. Check once more to ensure that the module is positioned correctly.
5. Close the compartment cover and secure with four screws.
4-14
Expanding Your Computer
Chapter 5
Using BIOS Setup and System Recovery
BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features.
System Recovery reinstalls Windows to your computer and restores it to the factory default status.
This chapter tells you how to use the BIOS Setup and System Recovery.
Using BIOS Setup and System Recovery 5-1
1
BIOS Setup
When and How to Use
You need to run BIOS Setup Utility when:
You see an error message on the screen requesting you to run BIOS
Setup Utility.
You want to restore the factory defaul t BIOS settings. You want to modify some specific settings according to the hardware. You want to modify some specific settings to optimize the system
performance.
To run BIOS Setup Utility, press the F2 key when the prompt appears on the screen during the system startup. The prompt shows up on the screen for only a few seconds. You must press the F2 key quickly. The BIOS Setup Utility main screen appears as shown next.
Main Advanced Security Boot Exit
Model:
SATA HDD:
System Time:
System Date:
Processor Info: Installed System Memory:
System BIOS Version: KBC/EC BIOS Version:
LAN MAC Address: Serial Number:
F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select Sub-Menu F10 Save and Exit
5-2
Using BIOS Setup and System Recovery
V200-X
[INTEL SSDSA2M080G2GC] 80026MB
[16:33:08]
6
[07/05/2010]
Intel(R)Core(TM)i7 CPU U620@2.00GHz 2048MB
R1.01 R1.01u
00-22-20-0A-98-B4 12231241241324
1
In general, you can use the arrow keys to move around and + / – keys to change the setup values. Keyboard information can be found at the bottom of the screen.
NOTE:
The BIOS Setup Utility screens shown in this chapter are for your reference
only. The actual items or settings on your computer may differ.
The BIOS Setup Utility program may have been updated after the publication
of this manual.
The settings you select in your operating system might override similar
settings in BIOS Setup Utility.
Main Menu
The Main menu contains the system date and time settings as well as shows the basic configuration of the system.
Main Advanced Security Boot Exit
Model:
SATA HDD:
System Time:
System Date:
Processor Info: Installed System Memory:
System BIOS Version: KBC/EC BIOS Version:
LAN MAC Address: Serial Number:
F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select Sub-Menu F10 Save and Exit
V200-X
[INTEL SSDSA2M080G2GC] 80026MB
[16:33:08]
6
[07/05/2010]
Intel(R)Core(TM)i7 CPU U620@2.00GHz 2048MB
R1.01 R1.01u
00-22-20-0A-98-B4 12231241241324
System Time sets the system time. System Date sets the system date.
Using BIOS Setup and System Recovery 5-3
Disabled
Advanced Menu
The Advanced menu contains the advanced settings as shown next.
Main Advanced Security Boot Exit
Japanese Keyboard:
SATA Mode Total Graphics Memory: USB Wake-Up From S3 High Brightness Thermal:
TouchScreen: Serial port COM1: Serial port COM2: Serial port COM4:
Boot-time Diagnostic Screen:
Wake-On-LAN(WOL) Turbo Mode Intel Trusted Execution Intel AMT Setup Prompt:
F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select Sub-Menu F10 Save and Exit
Japanese Keyboard enables support for the Japanese keyboard.
[Disabled] [AHCI] [MaxDVMT] [Disabled] [Disabled]
[Enabled] [Enabled] [Enabled] [Enabled]
[Disabled]
[Disabled] [Enabled] [Disabled] [Enabled]
Item Specific Help
Support Japanese Keyboard
SATA Mode sets the mode to enhanced AHCI (Advanced Host Controller Interface) or IDE. Turbo memory feature works only when the SATA AHCI mode is enabled.
Total Graphics Memory sets the amount of total gra phics memory (pre-allocated + fixed + DVMT) for use by the internal graphics device.
USB Wake-Up From S3 allow a USB d evice activity to wake up the system from S3 (Sleep) state.
High Brightness T hermal allows dynamic control of maximum LCD brightness level according to the ambien t temperature. This helps protect the LCD under over-heating situations.
5-4
Using BIOS Setup and System Recovery
Digitizer Type or TouchScreen (actual item shown depends on your model)
Digitizer Type allows you to select the type of digitiz er you are using. TouchScreen allows you to unconditionally disable it when set at
Disabled.
Serial Port COM1/COM2/COM4 allows you to uncondi tionally disable i t when set at Disabled.
Boot-time Diagnostic Screen allows you to display the diagnostic screen during system boot-up.
Wake-On-LAN (WOL) allow a LAN activity to wake up the system from S3 (Sleep) state.
Turbo Mode enables or disables Processor Turbo Mode. Intel Trusted Execution enables utilization of additional hardware
capabilities provided by Intel® Trusted Execution Technology. Intel AMT Setup Prompt sets if the prompt for entering Intel AMT Setup
appears during POST. If disabled, you can not enter Intel AM T Setup.
Using BIOS Setup and System Recovery 5-5
c
E
Security Menu
The Security menu contains the security settings, which safeguard your system against unauthorized use.
Main Advanced Security Boot Exit
Supervisor Password Is: User Password Is:
Set Supervisor Password:
Set User Password
Password on boot:
TPM Support
F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select Sub-Menu F10 Save and Exit
Set Clear
[Enter]
nter
[Enter]
[Disabled]
[Disabled]
Item Specific Help
Supervisor Password
ontrols access to the
setup utility.
Supervisor/User Password Is shows whether you have set the supervisor/user password or not for the system.
Set Supervisor/User Password sets the supervisor/user password. When typing the password, first make sure that Num Lock is off, and then type the password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter. You can set the supervisor/user password to be required for starting up the system and/or entering BIOS Setup.
NOTE:
You can set the user password only when the supervisor password has been
set.
If both the administrator and user passwords are set, you can enter any of
them for starting up the system and/or entering BIOS Setup. However, the user password only allows you to view/change the settings of certain items.
5-6
Using BIOS Setup and System Recovery
Password on Boot allows you to enable or disable the entering of password for booting up your system. Once the password is successfully set and this item is enabled, it is required for booting up the system.
TPM Support enables or disables TPM support. TPM (Trusted Platform Module) is a component on your computer’s mainboard that is specifically designed to enhance platform security by providing a protected space for key operations and other security critical tasks.
NOTE:
To use the TPM feature, the TPM driver supplied with your computer must be
installed.
The next two items Current TPM State and Change TPM State would only appear
if the item TPM Support is set at Enabled.
Current TPM State shows the current TPM state. Change TPM State allows you to select between No Change, Clear,
Deactivate & D isable, and Enable & Activate.
Using BIOS Setup and System Recovery 5-7
Boot Menu
The Boot menu sets the sequence of the devices to be searched for the operating system.
Main Advanced Security Boot Exit
Boot priority order:
1: USB FDC:
2: SATA HDD: INTEL SSDSA2M080G2GC – (S1) 3: USB KEY: 4: USB HDD: 5: LAN BOOT: IBA GE Slot 00C8 v1338 6: 7: 8:
Excluded from boot order:
: USB CDROM:
F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. <f> and <r> specifies the device fixed or removable <x> exclude or include the device to boot. <Shift + 1> enables or disables a device. <1 – 4> Loads default boot sequence.
The bootable devices will be automatically detected during POST and shown here, all o wi n g y ou to s et th e s eq u en c e th a t the BI OS u se s to l o o k f o r a device from which to load the OS. Below is a brief description of keyboard usage:
Key Function
, Selects (highlight) a boot device. +, – Changes the boot sequence.
1 to 4 Loads the defaul t boot sequence. X
Shift+1
5-8
Using BIOS Setup and System Recovery
Moves the highlighted boot device from the “Boot priority order” list to the “Excluded from boot order” list, and vice versa.
Deactivates/activates the h ighlighted boot device on the “Boot priority order” list. When a device has been deactivated, an “!” (exclamation) symbol appears beside the item and
system will bypass it when detecting boot device during POST.
Exit Menu
The Exit menu displays ways of exiting BIOS Setup Utility. After finishing with your settings, you must save and exit so that the changes can take effect.
Main Advanced Security Boot Exit
Exit Saving Changes
Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes
F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Exit System Setup and save your changes to CMOS.
Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility.
Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made.
Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items. Saves Changes saves the changes you have made.
Using BIOS Setup and System Recovery 5-9
System Recovery
Use System Recovery when:
Your Windows operating system does not start at all. You want to restore the factory defaul t Windows settings.
WARNING: Using this feature will reinstall Windows to your system. All data on the hard disk drive will be lost.
To run System Recovery:
1. During system startup when the following screen appears, press Ctrl + Alt + F2 keys for four seconds.
2. The message
to factory default. All data on HDD will be lost
screen to ask if you want to access System Recovery. Type 1 to continue.
5-10
Using BIOS Setup and System Recovery
This will help you reinstall Windows to the whole HDD
appears on the
3. A warning message appears as follows:
****************************************
You must accept the following terms before performing the recovery process:
1. The recovery software is solely the purpose of reinstalling or restoring software associated with the hard disk of this operating Getac machine.
2. Except the above, no other use is granted hereunder.
****************************************
(1)Yes, I agree to the provisions of this agreement and wish to continue. (0)No, I do not agree to the provisions of this agreement and do not wish to continue.
Type 1 to continue.
4. Type Y when the message
(Y)Yes (N)No
appears onscreen. The following screen appears and
Are you sure you want to recover now?
system will perform the recovery process and Windows operating system will be re-installed to its d efault setting:
Using BIOS Setup and System Recovery 5-11
5. After the recovery process has been completed successfully, the GSI (Getac Smart Installer) screen is displayed at the first boot-up of Windows operating system.
6. GSI will automatically perform system hardware detection and driver installation. After GSI has completed the whole process successfully, system will reboot.
5-12
Using BIOS Setup and System Recovery
Loading...