GE Security VDT14130WDM-SC-R3, VDT14130WDM-SC, VDT14130WDM, VDT14130WDM-C Specsheet

VDT/VDR14100WDM Series

IFS Digitally Encoded Video with

Bi-Directional Data

Overview

The IFS VDT/VDR14100WDM series video transmitter/
receiver and data transceiver support simultaneous
broadcast quality transmission of 10-bit digitally encoded
video and bi-directional data over one multimode or single
mode optical fiber. The modules are universally compatible
with major CCTV camera manufacturers and support
RS-232, RS-422, Sensormatic “Sensornet” and 2-wire or
4-wire RS-485 data interfaces, and most major data
protocols. Plug-and-play design ensures ease of
installation requiring no electrical or optical adjustments.
Each transceiver incorporates status indicating LED’s for
monitoring of proper system operation. The modules are
available in either stand-alone or rack mount versions.

Application Examples

• High Performance CCTV with PTZ Control

Standard Features

• 10-Bit Digitally Encoded Video Transmission

• Exceeds RS-250C Short-Haul Transmission

• NTSC, PAL, SECAM Compatible

• Full Color Compatibility

• Supports RS-232, RS-422, Sensormatic “Sensornet” or
RS-485 (2-wire or 4-wire) Data Interfaces

• No In-field Electrical or Optical Adjustments Required

• LED Status Indicators For Monitoring All Critical
Operating Parameters

• Tested and Certified by an Independent Testing Laboratory
for Full Compliance with the Environmental Requirements
(Ambient Operating Temperature, Mechanical Shock,
Vibration, Humidity with Condensation, High-Line/
Low-Line Voltage Conditions and Transient Voltage
Protection) of NEMA TS-1/TS-2 and the Caltrans
Specification for Traffic Signal Control Equipment

• Integrated WDM for Greater Reliability

• Hot-Swappable Rack Modules

Digitally Encoded
Video with
Bi-Directional Data

Broadcast quality transmission
of 10-bit digitally encoded
video and bi-directional data
over one multimode or
single mode optical fiber.

• Automatic Resettable Fuses on all Power Lines

• Distances up to 43 Miles (69 km)

• Comprehensive Lifetime Warranty

Video

(Coax)

VDT14130WDM VDR14130WDM

1 Fiber

9/125µm SM

up to 31 miles

(51 km)

Video

(Coax)

Control

Data

PTZ Control

Control

Data

ifs

International

Fiber

Systems

Incorporated

203.426.1180

ifs

International

Fiber

Systems

Incorporated

203.426.1180

Specifications

Video

Video Input: 1 volt pk-pk (75 ohms)
Bandwidth: 5 Hz - 10.0 MHz
Differential Gain: <2%
Differential Phase: <0.7°
Tilt: <1%
Signal-to-Noise Ratio (SNR): >67 dB @ Maximum Optical Loss Budget

Data

Data Interface: RS-232. RS-422, Sensormatic “Sensornet”, 2 and 4-wire RS-485 w/Tri-State
Data Format: NRZ, NRZI, Manchester, Bi-phase
Data Rate: DC-512 Kbps
Bit Error Rate (BER): <1 in 10˚ @ Maximum Optical Loss Budget
Operating Mode: Simplex or Full Duplex

Wavelength 1310/1550 nm, Multimode or Single Mode

Optical emitter Laser Diode

Number of fibers 1

Connectors

Optical: ST, SC or FC (see ordering information) (for SC - Rack Mount only)
Power: Terminal Block with Screw Clamps or Type DB-9P Connector
(specify at time of order)
Video: BNC (Gold Plated Center-Pin)
Data: Terminal Block with Screw Clamps (optional type DB-25 connector)

Electrical & Mechanical

Power:
Surface Mount: 12 VDC @ 500 mA
Rack: From Rack
Number of Rack Slots: 2
Current Protection: Automatic Resettable Solid-State Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 7.0 x 4.0 x 2.0 in., 17.8 x 10.2 x 5.1 cm
Rack Mount: 7.7 x 5.0 x 2.0 in., 19.6 x 12.7 x 5.1 cm
Shipping Weight: < 2 lbs./0.9 kg

Environmental

MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†

†May be extended to condensation conditions by adding suffix ‘–C’ to
model number for conformal coating.

Ordering Information

Part Number

Multimode

62.5/125µm**

Single Mode
9/125µm

Accessories

◆

Options

*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth.
**For 50/125 Fiber, subtract 4 dB from Optical Power Budget.

◆

All accessories are third party manufactured.

VDT14120WDM
VDR14120WDM

VDT14130WDM
VDR14130WDM
VDT14130WDM-HP

PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)

Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-SC’ to Model Number for SC Optical Connector - (For Single Mode Equipment and Rack Mount only)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
Add ‘-25’ to Model Number for Type DB-25S Data Channel Connector
Add ‘-FC’ to Model number for FC Optical Connector (Single Mode Equipment only)

Description

Video Transmitter/Data Transceiver (1310/1550 nm)
Video Receiver/Data Transceiver (1550/1310 nm)

Video Transmitter/Data Transceiver (1310/1550 nm)
Video Receiver/Data Transceiver (1550/1310 nm)
Video Transmitter/Data Transceiver (1310/1550 nm)

System Design

Fibers Required

1

1

Optical Pwr. Budget

7 dB

17 dB

23 dB

Max. Distance*

1.9 miles (3 km)

31 miles (51 km)

43 miles (69 km)