GE Security UVD-XP3DNR-VA9 User Manual
GE
Security
UVD-XP3DNR(-P) Camera User
Manual
REV 01.00 • ISS 02SEP09
Copyright © 2009 GE Security, Inc.
This document may not be copied in whole or in part or otherwise reproduced without prior
written consent from GE Security, Inc., except where specifically permitted under US and
international copyright law.
Disclaimer The information in this document is subject to change without notice. GE Security, Inc.
(“GE Security”) assumes no responsibility for inaccuracies or omissions and specifically disclaims
any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or
indirectly, of the use or application of any of the contents of this document. For the latest
documentation, contact your local supplier or visit us online at www.gesecurity.com.
This publication may contain examples of screen captures and reports used in daily operations.
Examples may include fictitious names of individuals and companies. Any similarity to names
and addresses of actual businesses or persons is entirely coincidental.
Trademarks and patents GE and the GE monogram are trademarks of General Electric Company. The UltraView name
and logo are trademarks of GE Security.
Other trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user
documentation for details. For the latest product information, contact your local supplier or visit
us online at www.gesecurity.com.
FCC compliance This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
You are cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user ’s authority to operate the equipment.
Certification and compliance
European Union directives 1999/5/EC (R&TTE directive): Hereby, GE Security declares that this device is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info
.
Contact information
2004/108/EC (EMC directive): Non-European manufacturers must designate an authorized
representative in the Community. Our authorized manufacturing representative is:
GE Security B.V., Kelvinstraat 7,
6003 DH Weert, The Netherlands.
For contact information see our Web site: www.gesecurity.com
EMEA: For contact information see our Web site: www.gesecurity.eu
Content
Preface 3
Safety terms 3
Product description 4
Features 4
User guidelines 4
Components 5
OSD control pad 6
Installation 7
Cable connection 7
Camera installation 7
Angle adjustment 7
Focus adjustment 8
Connect the monitor 8
Programming 9
Navigation 9
Main menu 9
Presets menu 10
Setup menu 10
Viewing menu 14
Exposure menu 14
White balance menu 15
Save/restore menu 15
Menu Map 16
UVD-XP3
DNR(-P) Camera User Manual i
Preface
This is the UVD-XP3DNR(-P) Camera. This document includes an overview of the
product and detailed instructions explaining:
• how to connect the camera; and
• how to program the camera.
• how to adjust the camera angle and focus
To use this document effectively, you should have the following minimum
qualifications:
• a basic knowledge of CCTV systems and components; and
• a basic knowledge of electrical wiring and low-voltage electrical connections.
Note: A qualified service person, complying with all applicable codes, should perform
all required hardware installation.
Safety terms
These terms may appear in this manual:
CAUTION: Cautions identify conditions or practices that may result in damage to the
equipment or other property.
WARNING: Warnings identify conditions or practices that could result in equipment
damage or serious personal injury.
UVD-XP3
DNR(-P) Camera User Manual 3
Product description
The UVD-XP3DNR(-P) (rugged dome) color video cameras is a 24 VAC/12 VDC model.
The cameras are equipped with a digital signal processor (DSP) for processing the
video signal.
Features
Camera features include:
• Next-generation XPosure technology.
• Improved low-light performance and color balance.
• 540 TVL lines color.
• Dynamic range 95 dB (typical), 120 dB (maximum).
• Preset modes optimized for various environments.
• Onscreen display interface.
User guidelines
Use the following guidelines:
• Program as many camera settings as possible before mounting the camera. Take
appropriate safety precautions while completing programming after installation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.
Do not use the camera outside the temperature range specifications: -57 to 122°F
(-50 to +50°C).
• If the light source where the camera is installed experiences rapid, widevariations in lighting, the camera may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do not expose the camera to
rain or moisture and do not remove the cover or back.
4 UVD-XP3
DNR(-P) Camera User Manual
Loading...