TruVision™ TVC-SD Series
Smoke Detector Camera
Installation Manual
Copyright
© 2010 GE Security, Inc.
This document may not be copied in whole or in part or otherwise
reproduced without prior written consent from GE Security, Inc.,
except where specifically permitted under US and international
copyright law.
Disclaimer
The information in this document is subject to change without
notice. GE Security, Inc. (“GE Security”) assumes no responsibility for
inaccuracies or omissions and specifically disclaims any liabilities,
losses, or risks, personal or otherwise, incurred as a consequence,
directly or indirectly, of the use or application of any of the contents
of this document. For the latest documentation, contact your local
supplier or visit us online at www.gesecurity.com.
This publication may contain examples of screen captures and
reports used in daily operations. Examples may include fictitious
names of individuals and companies. Any similarity to names and
addresses of actual businesses or persons is entirely coincidental.
Trademarks and patents
GE and the GE monogram are trademarks of General Electric
Company.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Intended use
Use this product only for the purpose it was designed for; refer to
the data sheet and user documentation for details. For the latest
product information, contact your local supplier or visit us online at
www.gesecurity.com.
FCC compliance
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
You are cautioned that any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Manufacturer
GE Security, Inc.
HQ and regulatory responsibility:
GE Security, Inc., 8985 Town Center Parkway,
Bradenton, FL 34202, USA
European Union
directives
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information see our Web site: www.gesecurity.com.
For contact information see our Web site: www.gesecurity.eu.
Smoke Detector Camera Table of Contents
1069589A / April 2010 3
TABLE OF CONTENTS
BEFORE YOU BEGIN................................................................4
1 ATTACHING THE HOUSING AND CABLES..............................5
2 ADJUSTING THE CAMERA...................................................8
APPENDIX A: UPGRADING OR ADDING CAMERAS ......................9
CAMERA SPECIFICATIONS................................................11
Before You Begin Smoke Detector Camera
4 1069589A / April 2010
BEFORE YOU BEGIN
Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to
local codes.
This manual provides installation and operation information. To use this
document, you must have the following minimum qualifications:
• A basic knowledge of CCTV systems and components
• A basic knowledge of electrical wiring and low-voltage electrical
hookups
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following
WARNING, CAUTION, and Note statements identify potential hazards:
* WARNING:
Improper use of this equipment can cause severe bodily injury or
equipment damage.
** CAUTION:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
Smoke Detector Camera Attaching the Housing and Cables
1069589A / April 2010 5
1 ATTACHING THE HOUSING AND CABLES
Smoke detector camera units are shipped with one down-viewing
camera to the unit. All cameras (in units and upgrade kits) are shipped
already focused.
1) Use the adapter or the housing as a template and mark the positions
of the mounting holes on the mounting surface. See
Figure 1.
2) Within the outline of the adapter or between the mounting holes of
the housing, cut a hole to accommodate the power and video
cables. See
Figure 1.
Mounting holes
Cable-entry hole
(Large enough to
accommodate the
power and video
cables.)
Figure 1. Mounting and cable-entry holes for the adapter and housing
3) Follow your local building codes for drilling the mounting holes and
cutting the cable-entry hole.
4) If using the adapter, use the four surface-mount screws and anchors
to attach the adapter to the mounting surface. See
Figure 3.
5) If you are adding cameras to your unit, follow the instructions in
section Appendix A: Upgrading or Adding Cam eras.
6) If you need to verify or change the focus or field of view of your unit’s
camera(s), refer to section
2 Adjusting the Camera.
7) Locate an approved power source within reach of the unit’s power
transformer.
Attaching the Housing and Cables Smoke Detector Camera
6 1069589A / April 2010
8) Pull the facility video cable through the cable-entry hole in the
mounting surface.
9) Attach the provided BNC connector to the facility video cable.
Video out
10) Connect the video cable.
11) Insert the provided power
transformer into an approved
power source.
12 VDC power
Figure 2. Camera cables
Smoke Detector Camera Attaching the Housing and Cables
1069589A / April 2010 7
12) Attach the unit to the mounting surface. Be sure to rotate the housing
so that the camera(s) face the desired field of view. See
Figure 3.
With mounting adapter
Screw anchors
Mounting adapter channel
Mounting adapter (optional)
Surface-mount screws
Housing (exterior)
Housing-to-adapter screws
Without mounting adapter
Screw anchors
Housing (exterior)
Surface-mount screws
Figure 3. Attaching the unit to the mounting surface
Adjusting the Camera Smoke Detector Camera
8 1069589A / April 2010
2 ADJUSTING THE CAMERA
1) If you need to change a
camera’s focus, turn the lens.
Note: There is no set screw.
Figure 4. Focusing the camera
2) To position a camera, see
Figure 5.
Note: Positioning adjustments can
only be made to side viewing
cameras.
Figure 5. Positioning the camera
3) Return to step 7 of section 1 Attaching the Housing and Cables.
Smoke Detector Camera Upgrading or Adding Cameras
1069589A / April 2010 9
APPENDIX A: UPGRADING OR ADDING CAMERAS
To upgrade or add cameras to an existing unit, perform the following:
1) If the housing is already installed, detach it from the adapter or the
mounting surface. Reverse the steps shown in
Figure 3.
2) If you are adding a camera to your existing unit, perform the
following. Otherwise, proceed to step 3.
a) Carefully remove a section of black card cover from the screen
the camera will be mounted behind.
b) Locate an approved power source within reach of the camera’s
power transformer.
c) Pull another facility video cable through the cable-entry hole in
the mounting surface.
d) Attach the provided BNC connector to the facility video cable.
3) To verify or change the camera’s focus or field of view, go to section
2 Adjusting the Camera.
Upgrading or Adding Cameras Smoke Detector Camera
10 1069589A / April 2010
4) Attach the additional
camera or replace
an existing camera
as shown in
Figure 6.
Figure 6. Attaching camera
Video out
5) Connect the video cable.
Note: The unit can be ordered with
multiple cameras. Each camera has
its own video and power cables.
6) Insert the provided power
transformer into an approved
power source.
Note: Value and Premier models
use a 12 VDC power transformer,
while Ultra models use a
12 VDC/24 VAC power transformer.
12 VDC power
Figure 7. Camera cables
7) To attach (or reattach) the housing to the adapter or the mounting
surface, go to step 12 in section
1 Attaching the Housing and
Cables. See
Figure 3.
Smoke Detector Camera Upgrading or Adding Cameras
1069589A / April 2010 11
CAMERA SPECIFICATIONS
Model TVC-SDC2-HR TVD-SDS3-HR
Image sensor 1/3-in. interline transfer
CCD
1/3-in. interline transfer
CCD
Total Pixels NTSC: 811 (H) x 508 (V) NTSC: 811 (H) x 508 (V)
Effective Pixels NTSC: 768 (H) x 494 (V) NTSC: 768 (H) x 494 (V)
Scanning system 525 lines/ 60 fields 525 lines / 60 fields
Sync system 2:1 Internal 2:1 Internal
Resolution 550 TV lines 550 TV lines
S/N ratio >51 dB (AGC Off) >51 dB (AGC Off)
Electronic shutter AUTO 1/60 ~ 1/100,000
sec
AUTO 1/60 ~ 1/100,000
sec
Min. Illumination 0.4 Lux/F2.0 0.4 Lux/F2.0
Video output Composite 1.0 Vp-p/75 Ω Composite 1.0 Vp-p/75 Ω
Lens Type Pinhole: 2.8mm Pinhole: 3.87mm
Power source DC12V DC12V
Current 100mA (Max) 100mA (Max)
Operating
Temperature
-10º to 50º C
14º to 122º F
-10º to 50º C
14º to 122º F
Storage
Temperature
-20º to 70º C
-4º to 158º F
-20º to 70º C
-4º to 158º F
Loading...