GE Security CS575, CS375, CS175, CS275, CS875 Installer Manual

Download

imagination at work

Security

1052xxx

CS875-575-375-275-175 Alarm system

Installers Manual with CS5500 keypad

We declare under our sole responsibility that this product is in conformity with Directive 93/68/EEC (Marking) and/or complies to the essential requirements and all other relevant provisions of the 1999/5/EC (R&TTE) based on test results using (non)harmonized standards in accordance with the Directives mentioned.

www.gesecurity.com Copyright

(c) 2005 GE Security B.V.. All rights reserved. GE Security B.V. grants the right to reprint this manual for internal use only. GE Security B.V. reserves the right to change information without notice.

Signature of representative/manufacturer: Raoul van Bergen

Manager Control & Communication GE Interlogix B.V. Kelvinstraat 7 ………………………….. 6003 DH Weert The Netherlands

Place : Weert Date : 9 December 2003

Page 1 of 2 Number: 02.42c

SECURITY LIFESAFETY COMMUNICATIONS

MANUFACTURERS

DECLARATION OF CONFORMITY

For

Product identification:

Model/type : CS575 series BOM revision level : see model listing Category (description) : Alarm control panel Brand : GE-InterlogiX/Aritech / Sentrol/ESL/ITI/Caddx/Casi Rusco/Kalatel

Manufacturer:

GE Interlogix 2008 Orchard Avenue City West Business Campus Naas Road, Dublin 24

EU Representative:

GE Interlogix B.V. Kelvinstraat 7 6003 DH Weert The Netherlands

Concerning RTTE EMC Safety Telecom A sample of the product has been tested by:

Compliance Engineering Ireland Ltd.

RAYSTOWN, RATOATH ROAD, ASHBOURNE, CO. MEATH, IRELAND

Interlogix Ireland Limited Greenhills Centre, Greenhills Road, Tallaght, Dublin 24, IRELAND

Belcomlab

CE Qualification Plan: 02DUBCE5001-3 CS575

Test report reference

00E293-1 & 01E515-1 01DR575LV D-2 BCL/00-04

Applied standards

EN50130-4(1995) +A1(1998) EN50081-1(1992) EN55022(1994) +A1(1995) +A2 (1997) EN61000-3-2(1995) +A1(1995) +A2(1998) +A14(2000) EN61000-3-3(1995)

EN60950(2001) CTR21(1998)

+EG201121(1998)

Equipment class identifier (RF products falling under the scope of R&TTE)

X Not Applicable None (class 1 product)

(class 2 product)

Means of conformity

Signature of representative/manufacturer: Raoul van Bergen

Manager Control & Communication GE Interlogix B.V. Kelvinstraat 7 ………………………….. 6003 DH Weert The Netherlands

Place : Weert Date : 9 December 2003

Page 2 of 2 Number: 02.42c

Model listing (list of all product variants or models for which this declaration is valid)

Model Description BOM revision date

CS575 Control Panel 8 Zones Plastic

18-JUN-02

CS575M Control Panel 8 Zones Metal Hs

13-JUN-02

CS575S1 Control Panel 8 Zones Plastic

20-JUN-02

CS575S4 Control Panel 8 zones Varel

04-JUL-02

CS575S88 Control Panel 8 Securitas

21-MAR-02

CS575S88NTXF Control Panel 8 Securitas NO XFR

21-MAR-02

CS375 Control Panel 24 Zones

September 2003

CS375M Control Panel 24 Zones Metal

September 2003

CS575S88-NO Control Panel 8 Zones Securitas Norway

November 2003

CS575S88-SW Control Panel 8 Zones Securitas Sweden

December 2003

CS575S88-DK Control Panel 8 Zones Securitas Denmark

December 2003

CS575S88-BE Control Panel 8 Zones Belgacom

December 2003

RK575 Securitas Retrofit Solution

December 2003

CS375S88-BE Control Panel 16 Zones Belgacom

December 2003

CS375S88-SW Control Panel 16 Zones Securitas Sweden

December 2003

CS375S88-DK Control Panel 16 Zones Securitas Denmark

December 2003

CS375S88-NO Control Panel 16 Zones Securitas Norway

December 2003

CS875-575-375-275-175 Installers Manual with CS5500 keypad i

Contents

Section A: Installing and programming a basic system

1 Introducing the CSx75 system ................................................................................... A-1-1

1.1 Getting started..............................................................................................................A-1-1

1.1.1 Welcome.....................................................................................................................A-1-1

1.1.2 Default country codes.................................................................................................A-1-1

1.2 Keypads.......................................................................................................................A-1-1

1.2.1 CS5500 keypad..........................................................................................................A-1-1

1.2.2 Other LCD and LED keypads.....................................................................................A-1-3

2 Designing the CSx75 system...................................................................................... A-2-1

2.1 System versions...........................................................................................................A-2-1

2.2 Parts of the system ......................................................................................................A-2-2

3 Installation guidelines................................................................................................. A-3-1

3.1 Mains power connection ..............................................................................................A-3-1

3.2 Mounting ......................................................................................................................A-3-1

3.3 Cabling.........................................................................................................................A-3-1

3.3.1 Shielded and unshielded cable................................................................................... A-3-1

3.3.2 Twisted and untwisted cable.......................................................................................A-3-1

3.4 Wiring guidelines..........................................................................................................A-3-1

3.5 Defaulting the panel.....................................................................................................A-3-2

3.6 Using the DIP switch diagrams....................................................................................A-3-2

4 Installing a basic system ............................................................................................ A-4-1

4.1 Wiring zones ................................................................................................................A-4-1

4.1.1 General.......................................................................................................................A-4-1

4.1.2 Dual wiring..................................................................................................................A-4-1

4.1.3 Single wiring ...............................................................................................................A-4-1

4.2 Installing the control unit ..............................................................................................A-4-1

4.2.1 CS575M/CS875M (large metal housing)....................................................................A-4-2

4.2.2 CS275/CS375/CS575/CS875 (polycarbonate housing) ............................................A-4-4

4.2.3 CS175M/CS275M/CS375M/CS575SM (small metal housing) ...................................A-4-6

4.3 Installing the keypad ....................................................................................................A-4-8

4.3.1 Wiring the keypad.......................................................................................................A-4-8

4.3.2 Wiring several keypads together ................................................................................A-4-9

4.4 Wiring sounders.........................................................................................................A-4-11

4.4.1 Wiring a sounder with EOL protection......................................................................A-4-11

4.5 Wiring fire detectors ...................................................................................................A-4-13

4.5.1 4-wire fire detector (CS275-375-575-875)................................................................A-4-14

4.5.2 2-wire fire detector (CS275-375-575-875)...............................................................A-4-14

4.5.3 4-wire fire detector (CS175)......................................................................................A-4-15

4.6 Wiring the outputs......................................................................................................A-4-16

4.7 Control unit wiring diagrams.......................................................................................A-4-17

4.7.1 CS175......................................................................................................................A-4-17

4.7.2 CS275......................................................................................................................A-4-18

4.7.3 CS375, CS575 and CS875.......................................................................................A-4-19

5 Programming the system............................................................................................ A-5-1

5.1 Powering up the system...............................................................................................A-5-1

5.2 Entering programming mode........................................................................................A-5-1

5.2.1 Changing the user interface language........................................................................A-5-1

5.3 Navigating the menus ..................................................................................................A-5-1

5.3.1 Command menu.........................................................................................................A-5-1

5.4 Selecting a menu option ..............................................................................................A-5-2

5.5 Changing a menu option.............................................................................................. A-5-2

5.5.1 Changing selection list entries....................................................................................A-5-2

5.5.2 Changing binary entries..............................................................................................A-5-2

5.5.3 Changing numeric entries...........................................................................................A-5-2

5.5.4 Changing phone numbers and phone prefixes...........................................................A-5-3

5.6 Exiting the menu system..............................................................................................A-5-3

CS875-575-375-275-175 Installers Manual with CS5500 keypad ii

5.7 Editing text ...................................................................................................................A-5-3

5.7.1 Overview.....................................................................................................................A-5-3

5.7.2 Example......................................................................................................................A-5-4

5.7.3 Word library................................................................................................................A-5-4

5.7.4 Installer message........................................................................................................A-5-5

6 Setting up a communicator ....................................................................................... A-6-1

6.1 Reporting......................................................................................................................A-6-1

0.0.1 Reporting to one phone number .................................................................................A-6-1

6.1.1 Backup reporting ........................................................................................................A-6-1

6.1.2 Dual reporting.............................................................................................................A-6-2

6.1.3 Split reporting..............................................................................................................A-6-2

Section B Installing and programming the modules

1 Enrolling modules ...................................................................................................... B-1-1

1.1 Enrolling the system modules................................................................................................B-1-1

1.2 Defaulting the modules..........................................................................................................B-1-1

1.3 Glossary.................................................................................................................................B-1-1

2 Programming the control panel ................................................................................ B-2-1

2.1 Overview................................................................................................................................B-2-1

2.2 Programming inputs...............................................................................................................B-2-1

2.2.1 Defining a zone ...........................................................................................................B-2-2

2.2.2 Copying zone settings ................................................................................................B-2-2

2.2.3 Editing a zone type .....................................................................................................B-2-3

2.2.4 Setting swinger shutdown ...........................................................................................B-2-3

2.3 Programming outputs.............................................................................................................B-2-4

2.3.1 Configuring an output ..................................................................................................B-2-4

2.3.2 Configuring the internal siren.......................................................................................B-2-5

2.3.3 Programming the keypad sounder...............................................................................B-2-6

2.4 Assigning codes.....................................................................................................................B-2-6

2.4.1 Setting up the installer code........................................................................................B-2-6

2.5 Setting communication options..............................................................................................B-2-7

2.5.1 Defining communication with a central station.............................................................B-2-8

2.5.2 Defining communication with upload/download software ............................................B-2-8

2.5.3 Configuring the system autotest..................................................................................B-2-8

2.5.4 Enabling reporting........................................................................................................B-2-9

2.6 Configuring partitions.............................................................................................................B-2-9

2.6.1 Setting timers...............................................................................................................B-2-9

2.6.2 Configuring a partition................................................................................................B-2-10

2.7 Configuring the system........................................................................................................B-2-10

2.7.1 Setting timers.............................................................................................................B-2-11

2.7.2 Configuring system features......................................................................................B-2-11

2.8 Setting arm schedules .........................................................................................................B-2-11

2.8.1 Setting up schedules .................................................................................................B-2-11

2.9 Programming the system to work with a home automation system.....................................B-2-12

2.9.1 Enabling broadcasts..................................................................................................B-2-13

2.9.2 Enabling commands and requests............................................................................B-2-13

2.10 Glossary..................................................... ........................................................................B-2-14

2.11 Technical Specifications ....................................................................................................B-2-33

3 Programming the current keypads ........................................................................... B-3-1

3.1 Overview................................................................................................................................B-3-1

3.2 Configuring keypad features..................................................................................................B-3-1

3.3 Multi-area mode.....................................................................................................................B-3-2

3.4 Assigning X-10 devices..........................................................................................................B-3-2

3.5 Copying keypad settings........................................................................................................B-3-2

3.6 Configuring keypad text.........................................................................................................B-3-2

3.7 Setting the keypad partition and keypad number...................................................................B-3-3

3.8 Glossary.................................................................................................................................B-3-3

3.9 Technical specifications.........................................................................................................B-3-6

3.9.1 CS5006 LED keypad...................................................................................................B-3-6

3.9.2 CS5XX8 LED keypad, where XX is the country code..................................................B-3-6

3.9.3 CS5500 menu driven keypad ......................................................................................B-3-7

3.9.4 Keyswitch zones..........................................................................................................B-3-7

4 Programming the other keypads............................................................................... B-4-1

4.1 Glossary.................................................................................................................................B-4-1

CS875-575-375-275-175 Installers Manual with CS5500 keypad iii

5 Setting up the RF receivers ....................................................................................... B-5-1

5.1 Overview................................................................................................................................B-5-1

5.1.1 Types of receivers .......................................................................................................B-5-1

5.2 Installing an RF433 Mhz receiver ..........................................................................................B-5-2

5.2.1 Wiring an RF433 Mhz receiver....................................................................................B-5-2

5.2.2 Setting the RF433 Mhz receiver DIP switches ............................................................B-5-2

5.2.3 RF433 Mhz receiver status conditions.........................................................................B-5-3

5.3 Installing an RF868 Mhz receiver ..........................................................................................B-5-4

5.3.1 Wiring an RF868 Mhz receiver....................................................................................B-5-4

5.3.2 Setting the RF868 Mhz receiver DIP switches ............................................................B-5-4

5.3.3 RF868 Mhz receiver status conditions.........................................................................B-5-5

5.4 Programming the RF system.................................................................................................B-5-6

5.4.1 Defaulting the wireless modules..................................................................................B-5-6

5.4.2 Programming the wireless detectors ...........................................................................B-5-6

5.4.3 Configuring receiver features.......................................................................................B-5-7

5.4.4 Setting supervision windows........................................................................................B-5-7

5.5 Testing wireless sensors........................................................................................................B-5-8

5.5.1 RF433 Mhz system......................................................................................................B-5-8

5.5.2 RF868 Mhz system......................................................................................................B-5-8

5.6 Deleting sensors....................................................................................................................B-5-8

5.7 Glossary.................................................................................................................................B-5-9

5.8 Technical specifications.......................................................................................................B-5-11

5.8.1 RF433 receivers: RX8i4-pcb, RX16i4-pcb, RX48i4-pcb............................................B-5-11

5.8.2 RF868 receivers: RX8w8-pcb, RX16w8-pcb, RX32w8-pcb.......................................B-5-11

5.8.3 Empty housing RXWEH00 (868 Mhz) and RXIEH00 (433 Mhz)...............................B-5-11

6 Setting up the CS208H / CS208 / CS216 ................................................................... B-6-1

6.1 Overview................................................................................................................................B-6-1

6.2 CS208 / CS216 input expander.............................................................................................B-6-1

6.1.4 Installing the CS208 / CS216 input expander.............................................................B-6-1

6.1.5 Setting the DIP switches.............................................................................................B-6-1

6.1.6 Wiring the CS208 / CS216 input expander.................................................................B-6-3

6.3 CS208H input expander.........................................................................................................B-6-4

6.1.7 Installing the CS208H input expander........................................................................B-6-4

6.1.8 CS208H input expander board...................................................................................B-6-4

6.1.9 Setting the DIP switches.............................................................................................B-6-5

6.1.10 Wiring the CS208H input expander..........................................................................B-6-6

6.4 Programming the CS208H / CS208 / CS216 input expander................................................B-6-6

6.5 Glossary.................................................................................................................................B-6-7

6.6 Technical specifications.........................................................................................................B-6-7

6.6.1 CS208 / CS216 input expander...................................................................................B-6-7

6.6.2 CS208H input expander ..............................................................................................B-6-7

7 Setting up the CS507.................................................................................................. B-7-1

7.1 Overview................................................................................................................................B-7-1

7.2 Installing the CS507 output expander....................................................................................B-7-1

7.2.1 Setting the DIP switches..............................................................................................B-7-2

7.2.2 Wiring the CS507 output expander..............................................................................B-7-2

7.3 Programming the CS507 output expander ............................................................................B-7-4

7.3.1 Setting up schedules ...................................................................................................B-7-6

7.3.2 Configuring an output ..................................................................................................B-7-6

7.3.3 Configuring users.........................................................................................................B-7-6

7.4 Glossary.................................................................................................................................B-7-7

7.5 Technical specifications.........................................................................................................B-7-9

8 Setting up the CS586.................................................................................................. B-8-1

8.1 Overview................................................................................................................................B-8-1

8.2 Connecting the CS586 direct connect module.......................................................................B-8-1

8.2.1 Connecting the CS586 to a PC ...................................................................................B-8-1

8.2.2 Connecting the CS586 to a PC and a panel ...............................................................B-8-2

8.2.3 Connecting the CS586 to a panel ...............................................................................B-8-2

8.3 Programming the CS586 direct connect module ..................................................................B-8-2

8.3.1 Enabling memory transfer using the CS5500 keypad .................................................B-8-3

8.3.2 Enabling memory transfer using UDx75 software .......................................................B-8-3

8.4 Glossary.................................................................................................................................B-8-4

8.5 Technical Specifications ........................................................................................................B-8-4

9 Setting up the CS534.................................................................................................. B-9-1

9.1 Overview................................................................................................................................B-9-1

CS875-575-375-275-175 Installers Manual with CS5500 keypad iv

9.2 Installing the CS534 listen-in module.....................................................................................B-9-1

9.2.1 Wiring the CS534 listen-in module ..............................................................................B-9-2

9.2.2 General operating instructions.....................................................................................B-9-2

9.2.3 Control levels...............................................................................................................B-9-3

9.2.4 Tones...........................................................................................................................B-9-4

9.3 Programming the CS534 listen-in module.............................................................................B-9-5

9.3.1 Configuring listen-in options........................................................................................B-9-5

9.3.2 Programming timers....................................................................................................B-9-5

9.3.3 Setting volume levels...................................................................................................B-9-5

9.3.4 Assigning X-10 devices ...............................................................................................B-9-6

9.4 Glossary.................................................................................................................................B-9-6

9.5 Technical specifications.........................................................................................................B-9-8

10 Setting up the CS320.............................................................................................. B-10-1

10.1 Overview............................................................................................................................B-10-1

10.2 Installing the CS320 auxiliary power module.....................................................................B-10-1

10.2.1 Wiring the CS320 auxiliary power module...............................................................B-10-2

10.2.2 Setting the DIP switches............................................................ ... ... ........................B-10-2

10.2.3 Enrolling the CS320 auxiliary power module...........................................................B-10-3

10.3 Programming the CS320 auxiliary power module..............................................................B-10-3

10.3.1 Configuring outputs.................................................................................................B-10-3

10.3.2 Configuring features ................................................. ...............................................B-10-4

10.4 Glossary..................................................... ........................................................................B-10-5

10.5 Technical specification s.....................................................................................................B-10-7

11 Setting up the CS535.............................................................................................. B-11-1

11.1 Overview............................................................................................................................B-11-1

11.2 Installing the CS535 voice module.....................................................................................B-11-1

11.3 Programming the CS535 voice module.............................................................................B-11-2

11.3.1 Configuring the control panel for voice reporting.....................................................B-11-2

11.3.2 Recording voice messages......................................................................................B-11-2

11.3.3 Playing back messages...........................................................................................B-11-3

11.3.4 Configuring handshake and kiss off........................................ .................................B-11-3

11.4 Glossary..................................................... ........................................................................B-11-4

11.5 Technical specification s.....................................................................................................B-11-5

12 Setting up the CS1700............................................................................................ B-12-1

12.1 Overview............................................................................................................................B-12-1

12.2 Installing the CS1700 proximity reader..............................................................................B-12-1

12.2.1 Wiring the CS1700 proximity reader........................................................................B-12-2

12.2.2 Enrolling the CS1700 proximity reader....................................................................B-12-2

12.3 Programming the CS1700 proximity reader.......................................................................B-12-3

12.3.1 Programming badge functions.................................................................................B-12-3

12.3.2 Configuring X-10 functions......................................................................................B-12-4

12.3.3 Adding and deleting cards.......................................................................................B-12-4

12.4 Glossary..................................................... ........................................................................B-12-6

12.5 Technical specification s.....................................................................................................B-12-9

13 Setting up the CS7002............................................................................................ B-13-1

13.1 Overview............................................................................................................................B-13-1

13.2 Installing the CS7002 GPRS module................................................................................B-13-2

13.2.1 Enrol the SIM card on the GSM network........................ .........................................B-13-2

13.2.2 Inserting the SIM card..............................................................................................B-13-3

13.2.3 Wiring the CS7002 GPRS module...........................................................................B-13-3

13.2.4 Reporting LEDs ................................................ .......................................................B-13-3

13.3 Programming the CS7002 GPRS module .........................................................................B-13-4

13.3.1 Testing the RSSI value............................................................................................B-13-4

13.3.2 Reporting..................... ... ... ......................................................................................B-13-5

13.3.3 Using upload/download ............................................... ... .........................................B-13-6

13.4 Glossary..................................................... ........................................................................B-13-7

13.5 Technical specification s...................................................................................................B-13-13

14 Reserved.................................................................................................................. B-14-1

15 Setting up the CS7050............................................................................................ B-15-1

15.1 Overview............................................................................................................................B-15-1

15.2 Installing the CS7050 TCP/IP module ...............................................................................B-15-1

15.2.1 Wiring the CS7050 TCP/IP module .........................................................................B-15-2

15.2.2 LED indicators.................................... .....................................................................B-15-2

15.3 Programming the CS7050 TCP/IP module........................................................................B-15-3

15.3.1 Configuring TCP/IP reporting...................................................................................B-15-4

CS875-575-375-275-175 Installers Manual with CS5500 keypad v

15.3.2 Configuring email reporting......................................................................................B-15-4

15.3.3 Configuring reporting options...................................................................................B-15-5

15.3.4 Configuring upload/download..................... .............................................................B-15-5

15.4 Glossary..................................................... ........................................................................B-15-7

15.5 Technical specification s...................................................................................................B-15-11

16 Setting up the CS7501............................................................................................ B-16-1

16.1 Overview............................................................................................................................B-16-1

16.2 Installing the CS7501 ISDN dialler ....................................................................................B-16-1

16.2.1 LED indicators.................................... .....................................................................B-16-2

16.2.2 Mounting the CS7501 ISDN dialler..........................................................................B-16-2

16.2.3 Wiring the battery leads...........................................................................................B-16-6

16.3 Programming the CS7501 ISDN dialler.............................................................................B-16-7

16.3.1 Configuring phone reporting....................................................................................B-16-7

16.3.2 Configuring AL2 supervised ISDN connection.........................................................B-16-8

16.3.3 Uploading and downloading ....................................................................................B-16-8

16.4 Glossary..................................................... ........................................................................B-16-9

16.5 Technical specification s...................................................................................................B-16-13

17 Reading the event log ............................................................................................ B-17-1

17.1 Overview............................................................................................................................B-17-1

17.2 Event log events ................................................................................................................B-17-2

17.3 Glossary..................................................... ........................................................................B-17-4

18 Programming with the UDx75 software................................................................ B-18-1

18.1 Other methods of programming.........................................................................................B-18-1

18.2 Connecting the panel to the computer...............................................................................B-18-1

18.2.1 Connecting using a serial port.................... .............................................................B-18-1

18.2.2 Connecting using a modem.....................................................................................B-18-1

18.3 Programming with upload/download software ...................................................................B-18-2

18.3.1 Programming tasks.............................................................. ....................................B-18-3

Section C Reference

1 Appendices ..................................................................................................................C-1-1

1.1 Appendix 1: Reporting fixed codes in Contact ID or SIA...............................................C-1-1

1.2 Appendix 2: Overview of module numbers ...................................................................C-1-2

1.2.1 CS1700 door swipe module ........................................................................................C-1-2

1.2.2 Keypads.......................................................................................................................C-1-2

1.3 Appendix 3: Communicator formats..............................................................................C-1-3

1.4 Appendix 4: Service messages.....................................................................................C-1-3

1.5 Appendix 5: Tasks summary.........................................................................................C-1-6

1.6 Appendix 6: Word library words....................................................................................C-1-6

Section A:

Installing and programming a basic system

1 Introducing the CSx75 system .................................................................................................................................A-1-1

2 Designing the CSx75 system.....................................................................................................................................A-2-1

3 Installation guidelines...................................................................................................................................................A-3-1

4 Installing a basic system.............................................................................................................................................A-4-1

5 Programming the system...........................................................................................................................................A-5-1

6 Setting up a communicator.......................................................................................................................................A-6-1

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.1.1

Chapter 1: Introducing the CSx75 system

1.1 Getting started

1.1.1 Welcome

Welcome to the CSx75 system range. We hope that you find it a useful addition to our range of products. The CSx75 system design allows a fully loaded system to be housed in one single metal or plastic enclosure. It

can be expanded as required with additional modules. Five different panel types are available: the CS175, CS275, CS375, CS575 and CS875. In this manual they are known collectively as the CSx75.

This manual describes a CSx75 installation using the CS5500, the menu driven keypad. The CS5500 allows you to program the system easily using a menu structure.

1.1.2 Default country codes

Table 1-1: Default country codes lists the default codes used in each country.

The brackets contain the additional digits for the 6-digit codes.

1.2 Keypads

1.2.1 CS5500 keypad

The CS5500 LCD keypad allows you to program the CSx75 system using a menu structure.

Table 1-1: Default country codes

Country Country

code

User code Installer code Download access code

Baltic states 03 1122 1278 12780000 France 02 1122(56) 1278(00) 84800000 Belgium 11 1122(56) 1278(00) 12780000 Czech Republic 20 1122 1278 12780000 Denmark 07 1122(00) 1278(00) 12780000 Finland 28 1122 1278 12780000 France 02 1122(56) 1278(00) 84800000 Germany 04 1122(56) 1278(00) 12780000 Hungary 22 1122 1278 12780000 Ireland 12 1122 1278 12780000 Italy 10 7777(77) 8522(22) 84800000 Netherlands 01 1122(56) 1278(00) 12780000 Norway 05 1122(00) 1278(00) 12780000 Poland 18 1122(56) 1278(00) 84800000 Portugal 21 1122(56) 1278(00) 84800000 Slovak Republic 24 1122 1278 12780000 Spain 09 1122(56) 1278(00) 84800000 Sweden 06 1122(00) 1278(00) 12780000 UK 03 1122 1278 12780000

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.1.2

Power (green)

• On if the system is connected to the mains and the battery is OK.

• Flashes if the system has no battery or a low battery.

• Off if the system is not connected to the mains.

Ready (green)

• On when the system is ready to arm.

• Flashes when the system is ready to force arm.

• Off when the system cannot be armed.

Fire (red)

• On when a fire zone has been activated.

• Flashes when there is a problem with a fire zone.

• Off when all fire zones are operating correctly.

Function keys

•Press F1 to scroll to the start of the LCD message.

•Press F3 to scroll to the end of the LCD message. In multi-area mode, these keys have specific functions. If you select one or more areas in this mode:

•Press F1 to part arm the set of areas.

•Press F2 to full arm the set of areas.

•Press F3 to disarm the set of areas. You can program these keys to perform a function when not in multi-area mode.

Press No to:

• Cancel a change to the menu selection or

• Navigate to a higher level in the menu structure or

• Cancel a sequence when entering numeric data.

Press OK to:

• Activate the menu or

• Accept selection changes or

• Move forward in the menu structure or

• Complete a sequence when entering numeric data.

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.1.3

1.2.2 Other LCD and LED keypads

These are the other types of keypads that can be used with the CSx75 system. The LCD keypad can be used to program the system, but a menu structure is not provided.

It is recommended that you program the system using the CS550 keypad or the UDx75 upload/download software.

Hash

When editing text and phone numbers:

• Press # F1 to move to the first character or number.

• Press # F3 to move to the last character or number.

• Press # to delete from the current position to the last character or number.

Navigation keys

Press the navigation keys to scroll through menu lists and options. When in multi-area mode or not in a menu:

• Press  to display bypassed zones.

• Press  to display problem zones. When editing text and telephone numbers:

• Press  to overwrite or insert text.

• Press  to delete text.

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.2.1

Chapter 2: Designing the CSx75 system

2.1 System versions

There are five versions of the CSx75. The following table lists the features of each version and some differences between them.

Table 2-1: CSx75 versions

CS175 CS275 CS375/575 CS875

Number of wired zones on the CSx75

4688

Maximum number of zones

8 16 24 (CS375)

48 (CS575)

168

Outputs 3 (2 open collector and 1

fire reset)

4 on-board (open collector) 4 on-board (2 relay/2 open

collector)

4 on-board (2 relay/2 open collector)

Sounder outputs Internal sounder with built–

in siren driver for the internal sounder

Separate on-board external and internal sounder with built–in siren driver for the internal sounder

Maximum number of partitions

1248

Report formats Fast Format, Telim,

Franklin 4+2, SIA, XSIA, Siren T one, 200 baud FSK, Voice and Contact ID report formats

Fast Format, Telim, Franklin 4+2, SIA, XSIA, Siren T one, 200 baud FSK, Voice and Contact ID report formats

Hardware expansion 1 module

Keypads do not count as modules on the CS175

3 modules Keypads do not count as modules on the CS275

16 modules (CS375) 32 modules (CS575) Keypads count as modules when on the CS375-575

32 modules Keypads count as modules when on the CS875

Maximum number of user codes

8 (4 or 6-digit codes) 40 (4 or 6-digit codes) 66 (6-digit codes) or 99 (4-

digit codes)

66 (6-digit codes) or 99 (4digit codes)

Maximum number of keypads (up to 8 per partition)

8 16 16 32

Support for Proximity Reader

No No Yes Yes

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.2.2

2.2 Parts of the system

Table 2-2: System modules

Part number Part Purpose

CS5500 Keypad module Used to program the system. Other LCD and LED location based

keypads can also be used.

CS208/CS208H/CS216 Input expander

module

Expands the number of wired zones by 8 or 16 zones The wired zone expanders can only be used with the CS375, CS575 and CS875. You can only expand the CS175 and CS275 by using a wireless receiver.

CS507 Output expander

module

Expands the number of outputs available on the system.

CS586 Direct connect

module

Used as:

1. A direct connect interface between the panel and PC.

2. A storage device, when connected only to the PC. You can also read/write from 1 of the 4 locations via the UDx75 software.

3. A storage device, connected only to the panel. You can read/write from 1 of the 4 locations on the CSx75. The CS590 RS232 direct connect cable is used with the CS275-375575-875 and is connected directly to the PCB. The CS586 can be used on any panel in the range and connected to the 3-wire keypad bus.

CS7002 GPRS module Allows events to be reported via a GSM network or a GPRS network.

CS1700 Door swipe module Proximity card reader/door control module. You can program it to

control access in any or all areas. The CS1700 can only be used with the CS575 and CS875.

CS320 Auxiliary power

module

Provides additional power for modules attached to a panel.

CS535 Voice module Allows events to be reported using voice messages.

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.2.3

CS534 Audio (listen-in)

module

Two-way audio (listen-in) communicator that allows the situation on the premises to be monitored.

CS7050 TCP/IP Module Dual microprocessor-controlled Internet/Intranet interface used to

connect the CSx75 control panel to the OH Network Receiver.

CS7501 ISDN Module Integrated services digital network dialler that allows digital data to be

sent over an ISDN line.

Table 2-3: System equipment

Part number Purpose

AS270/271 Internal sounders

AS500 and AS290/390 External sounders

DB701 + DP721 and DB702 +DP721R Fire detector

Table 2-2: System modules

Part number Part Purpose

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.2.4

Table 2-4: Wireless Equipment

Part Number 433 MHz 868 MHz Purpose

Wireless Receiver RX8I4CA-pcb

RX16I4CA-pcb RX48I4CA-pcb

RX8W8CA-pcb RX16W8CA-pcb RX32W8CA-pcb

RF 433 versions provide RF capability for 8, 16, or 48 wireless/RF components.

RF868 versions provide RF capability for 8 or 16 or 32 wireless/RF components.

Wireless keyfobs RF352I4 (2 button)

RF354I4 (4 button)

RF354W8 (4 button) Arms and disarms the

system.

Micro multipurpose panic button

RF356I4 Not available Used for activating police,

medical, or auxiliary alarms throughout the premises. When the panic button is pressed, the LED mounted under the front cover will blink and an alarm signal is transmitted.

Wireless water resistant medical pendant

RF360I4 Not available Sends an alarm signal with

one button press to the panel.

Wireless fire detector RF572SI4

RF572NSTI4

RF572SW8 Battery powered fire

detector.

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.2.5

Wireless door window sensor

RF320I4 RF310I4

RF300W8 RF300W8B

Transmits events to the control panel via the RF receiver.

Wireless shock sensor RF620I4

RF620I4B

Not available Transmits events to the

control panel via the RF receiver.

Wireless glass break detector

RF903I4 RF903W8 Transmits events to the

control panel via the RF receiver.

Wireless motion sensor RF425I4

RF425I4PI

RF425W8 RF425W8PI

Battery powered PIR.

Table 2-4: Wireless Equipment

Part Number 433 MHz 868 MHz Purpose

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.2.6

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.3.1

Chapter 3: Installation guidelines

3.1 Mains power connection

Use the mains connector terminal for connecting the mains supply. You can use a fixed cable or a flexible mains lead to an earthed mains outlet. If fixed wiring is used, insert a dedicated circuit breaker in the power distribution network. In all cases, the mains connection must comply with local regulations.

IMPORTANT: Disconnect the mains power before opening the cabinet. To do th is:

• Disconnect the AC mains plug from the AC mains wall socket or

• Disconnect the mains with the dedicated circuit breaker. CAUTION: This unit can be provided with a lead battery inside. Dispose of this battery according to chemical

waste regulations only.

3.2 Mounting

• Ensure that the unit is mounted on a flat, solid, vertical surface so that the base will not flex or warp when the mounting screws/bolts are tightened.

• Leave a 50 mm clearance between equipment enclosures mounted side by side and 25 mm between the enclosure and the walkway.

• The battery mounting facility inside the housing is only useful for steady state use of the control panel. Remove the battery for transport of the control panel.

• Take care that wire terminals are isolated. Use tie wraps to prevent contact with any o the r w ires o r cir cui ts in case wires break.

3.3 Cabling

3.3.1 Shielded and unshielded cable

• In a clean environment, use unshielded cable. This provides the maximum cable length.

• In a harsh environment, use shielded cable. The maximum cable length is reduced as part of the signal will go into the shield. The amount of length lost depends on the type and quality of the shielded cable.

3.3.2 Twisted and untwisted cable

• You can use either twisted or untwisted cable for the bus. Since the bus only has 3 wires, twisted pair cable is not necessary.

3.4 Wiring guidelines

The CSx75 control panel has been designed, assembled and tested to meet the requirements of current relevant standards related to safety, emission and immunity with respect to environmental electrical and electromagnetic interference. Only a qualified electrician or other suitable trained and qualified person should attempt to wire this system to the mains or to the public telephone network.

1. Ensure that there is a good earth for the alarm system. A good earth is essential for effective resistance to electrical interference. Do not forget to provide a (network) earth for the telephone dialler.

2. Maintain a good separation between low voltage and mains supply cables. Use separate points of cable entry to the control panel cabinet.

• If the entry cable holes are used to route wiring into the control panel, always use a proper pipe fitting system by means of an appropriate conduit and junction box. For this purpose, use only materials of suitable flammability class (HB or better).

• Avoid cable ducts and cableways that contain mains power cables. This is particularly important when such ducts contain cables supplying electric motors, fluorescent lights or 3-phase power. If this is not possible,

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.3.2

shielded cable should be used and the cable should be connected to a GND terminal at the control panel end only.

3. The remote bus cable is used for communication between the control panel and the keypads/expanders. The

greatest care should be taken when installing this cable. Never split it into separate cables. Do not use cables with wires that are used for telephone connections or for switching, for example, flashing lights, sirens or relays.

4. For mains power connection, use the mains connector terminal either through a permanent wiring or a flexible mains cable to an earthed mains outlet. Always use cable ties to fix the mains cable, at the dedicated fixing point provided near the mains terminal connector.

• In case of permanent fixed wiring, insert an easily accessible, dedicated bipolar circuit breaker in the power distribution network.

• Never attempt to solder a mains connection wire’s end where they will be wired to the terminal connectors.

5. Avoid loops of wire inside the control panel and route cables so they do not lie on top or underneath the printed circuit board. The use of cable ties is recommended and improves neatness within the box.

6. The battery used with this unit, must be made of materials of suitable flammability class (HB or bett er).

7. Any circuit connected either directly to the on-board relay’s contact or to the external relay’s contact through the on-board electronic output, must be of SELV (Safety extra-low voltage) operating circuit.

• The mains switching relay must not be fitted inside the control panel cabinet.

• Always place a suppression diode (for example, a 1N4001) across the relay coil.

• Use only a relay with good insulation between the contacts and the coil.

8. The minimum clearance between equipment closures is 50 mm between equipment vents.

9. Only use units in a clean environment and not in humid air.

3.5 Defaulting the panel

IMPORTANT: Before installing and programming the system, default the panel to ensure that you have the correct country defaults according to your local regulations.

3.6 Using the DIP switch diagrams

• When the DIP switch is set to the ON position, the switch is at the top. This is illustrated in the DIP switch diagrams as

• When the DIP switch is set to OFF, the switch is at the bottom. This is illustrated in the DIP switch diagram as

OFF

• In this example the first, third and sixth DIP switches are ON and the second, fourth and fifth DIP switches are OFF.

• The DIP switch diagram demonstrates this as shown.

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.4.1

Chapter 4: Installing a basic system

4.1 Wiring zones

4.1.1 General

The control unit inputs are set up as standard EOL (4K7) freely programmable zones. However, by programming the zones as dual loop, all control unit zone inputs can be programmed to give alarm and tamper indication on the same zone.

4.1.2 Dual wiring

One zone includes both alarm and tamper wiring. The alarm devices are wired in series and a 4K7 resistor is fitted in parallel across the closed circuit contacts. The tamper contacts are wired in series with a 4K7 EOL resistor.

• All devices closed - loop resistance is 4K7.

• Tamper device open - loop is an open or short circuit.

• Alarm device open - loop resistance is 9K4 (i.e. EOL resistor PLUS parallel resistor).

4.1.3 Single wiring

Two zones are required, one zone for alarm and one zone for tamper. The tamper contacts are wired in series with a 4K7 EOL resistor.

Information on programming the zones can be found in chapter B-2 Programming the control panel.

4.2 Installing the control unit

The control panel is available in three separate housings. The method of installation and the positioning of expander modules vary depending on the housing used.

Zone terminal

Alarm contact

Sensor

Tamper contact

Zone terminal

Alarm contact

Sensor

Tamper contact

4K7

E.O.L.

COM

3 4

COM

222

4K7

E.O.L.

4K7

E.O.L.

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.4.2

The instructions below show the details for installing a basic system. For details on installing the CS7050, CS7501 and CS7002, see the relevant chapters.

The housing/enclosures covered in this manual are not suitable for every CSx75 model and may not be

available in your country. Contact your local supplier to get more information on availability.

4.2.1 CS575M/CS875M (large metal housing)

This large metal housing can be used with the CS375, CS575 and CS875.

1. Open the box.

2. Wire the panel.

3. If you are using a CS534 listen-in module, a CS535 voice module and a CS7002 GPRS module, complete the following steps:

- Attach a ribbon cable to the CS7002 GPRS mod ule.

- Attach a ribbon cable to the CS534 li st en-in module.

- Connect the CS7002 GPRS module and CS535 voice module with the ribbon cable.

- Connect the CS534 listen-in modu le and CS535 voice module with the ribbon cable.

- Add the pillars for the CS700 2 GPRS m odule to the board.

- Attach the CS7002 GPRS module to the main board via the ju mpers and pillars.

- Place the CS534 listen-in module and CS535 voice module on top of the CS7002 GPRS module in the

box.

4. If you are using a CS534 and a CS535 without a CS7002 complete the following steps:

- Attach the ribbon cable to the CS534 listen-in module.

- Connect the CS534 listen-in modu le and CS535 voice module with the ribbon cable.

- Add the pillars for the CS535 voice module to the board.

- Attach the CS535 voice modul e to the board via the jumpers and pillars.

CS375/575/875

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.4.3

- Attach the pillars for the CS534 listen-in module to the box.

- Insert the CS534 listen-in module in the box.

5. Add the pillars for the CS507 output module or CS208 / CS216 input expander or CS7002 GSM module to the box.

6. Mount the CS507 output module or CS208 / CS216 input expander or CS7002 GSM module.

7. Mount the pillars for a CS208 / CS216 input expander on the CS575/875 board.

8. Mount the CS208 / CS216 input expander on the CS575/875 board.

9. Wire the keypad bus for all modules. Check the relevant module chapter for wiring information. For information on mounting the CS7501 ISDN dialler, see chapter B-16 Setting up the CS7501.

10. Connect the battery and power up the panel.

CS7002

CS507

CS216

CS507

CS216

CS375/575/87

)

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.4.4

4.2.2 CS275/CS375/CS575/CS875 (polycarbonate housing)

This polycarbonate housing can be used with the CS275, CS375, CS575and CS875.

1. Unscrew the holding screw in the polycarbonate housing.

2. Open the box.

3. Lift off the lid of the box.

4. Flip up the PCB mounting tray.

5. If you are using a CS534 listen-in module, a CS535 voice module and a CS7002 GPRS module, complete the following steps:

- Attach the ribbon cable to the CS7002 GPRS module.

- Attach the ribbon cable to the CS534 listen-in module.

- Remove the sticky pads and insert the pillars for the CS7002 GPRS module in the box.

- Connect the CS7002 GPRS module to the m a in board.

- Flip down the PCB mounting tray.

- Attach the pillars for the CS535 voice module to the board.

- Attach the CS535 voice modul e to the board via the jumpers and pillars.

- Connect the CS7002 GPRS module and CS535 voice module with the ribbon cable.

- Connect the CS535 voice module and CS534 listen-in module with the ribbon cable.

6. If you are using a CS534 and a CS535 without a CS7002 complete the following steps:

- Attach the ribbon cable to the CS534 listen-in module.

- Remove the stic ky pads and insert the pillars for the CS534 listen-in module in the box.

CS275/375/575/875

CS534

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.4.5

- Connect the CS534 listen-in module to the box.

- Flip down the PCB mou nting tray.

- Attach the pillars for the CS535 voice mod ule to the board .

- Attach the CS535 voi ce mod ule to the board via the jumpers and pillars.

- Connect the CS534 list en-in module and CS535 voice module with the ribbon cable.

7. Attach the pillars for the CS208 / CS216 input expander or CS507 output module to the board.

8. Mount the CS208 / CS216 input expander or CS507 output module on the board.

9. Drill 0.3 mm holes for the card guides in the box.

10. Place the card guide (NX-CA-SL) in the box.

CS275/375/575/875

CS534

CS535

CS507

CS216

CS535

CS216 CS507

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.4.6

11. Screw in the card guides.

12. Use the card guides to mount up to 3 further pre-wired modules. Check the relevant module chapter for wiring information. For information on mounting the CS7501 ISDN dialler, chapter B-16 Setting up the CS7501.

13. Connect the control panel battery leads to the module.

14. Mount the RF receiver in the lid of the box. This facility is not available in every country.

15. If you are installing an RX8I4, RX16I4 or RX48I4 CA series receiver , you must insert the antennae through the lid.

16. Wire the keypad bus for any other modules that are not in the card guides.

17. Connect the battery and power up the panel.

4.2.3 CS175M/CS275M/CS375M/CS575SM (small metal housing)

This is a small metal housing that can be used with the CS175, CS275, CS375 and CS575.

1. Open the box.

2. Wire the panel.

3. If you are using a CS534 listen-in module, a CS535 voice module and a CS7002 GPRS module, complete the following steps:

- Attach the pillars for the CS7002 GPRS modu le to the main board.

CS175/275/375/575

CS535

CS534

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.4.7

- Mount the CS535 voice module to the extensio n gate (ju mp e r).

- Attach a ribbon cable to the CS534 listen-in module.

- Connect the CS534 list en-in module and CS535 voice module with the ribbon cable.

- Mount the CS7002 GPRS module on the pillars to the m a in board.

4. If you are using a CS534 and a CS535 without a CS7002 complete the following steps:

- Attach the pillars for the CS534 listen-in module or CS535 voice module to the main board.

- Mount the CS534 listen-in module or CS535 voice module to the extension gate (jumper).

- Mount the CS534 listen-in module or CS535 voice module on the pillars to the main board.

5. Add the pillars for the CS208 / CS216 input expander or CS507 output expander to the main board.

6. Mount the CS208 / CS216 input expander or CS507 output expander.

7. Wire the keypad bus for all modules. Check the relevant module chapter for wiring information. For information on mounting the CS7501 ISDN dialler, see chapter B-16 Setting up the CS7501.

8. Connect the battery and power up the panel.

CS216

CS507

CS216

CS175/275/375/575

CS575/875

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.4.8

4.3 Installing the keypad

1. Remove the keypad door.

2. Remove the bottom screw if fitted.

3. Place a short length of the shaft of the screwdriver in the hollow of the door hinge.

4. Twist the screwdriver carefully.

5. The two parts of the keypad should separate. Lift up the lid.

6. Mount the keypad on the wall using the mounting holes C.

7. Use the wire trunking B or wire cutout hole D to place the wires in the keypad.

8. Re-attach the base and lid.

9. Attach the pry-off tamper screw if desired.

4.3.1 Wiring the keypad

The keypad should be wired to the control unit as follows.

CSx75 CS5500

Aux +

COM

Data

13.8V

0101

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.4.9

4.3.2 Wiring several keypads together

The total cable length of wiring is restricted to 800 m. The chart below shows the wire gauge that should be used. These numbers are for one keypad at the end of the wire. When connecting more than one keypad to the end of the wire, a higher gauge wire is required.

4.3.2.1 Multidrop network

In a multidrop network, keypads are chained together. Each keypad is connected in parallel to the one before it.

4.3.2.2 Star network

In a star network, each keypad is wired back separately to the control unit terminals.

Table 4-1: Keypad bus length

Length Connected to CSx75

Length in Metres Wire mm² 110 0.50 200 0.75 333 1.00 500 1.50 800 2.50

CS875-575-375-275-175 Installers Manual with CS5500 keypad A.4.10

4.3.2.3 Star and multidrop network

You can create a combination of a star and multidrop network. The following diagram shows how four keypads can be connected using both methods.

CS875-575-375-275-175 Installers Manual with CS5500 keypadA.4.11

4.4 Wiring sounders

4.4.1 Wiring a sounder with EOL protection

Any zone can be used. It should be programmed as tamper and single EOL.

4.4.1.1

AS500



Tn all cases, select negative hold-off on the sounder.

Beacon - hold off

Tamper

Piezo

Siren - hold off

Tamper

Piezo

+13.8 V

Beacon

Piezo

GND

Beacon

CSX75

AS500

DATA

AUX+

COM

4K7

9 8 7 6 5 4 3 2 10 1 11

4K7

+ 179 hidden pages

GE Security CS575, CS375, CS175, CS275, CS875 Installer Manual

Specifications and Main Features

Frequently Asked Questions

User Manual