Page 1
Super 130.2 S
Super 130.2
Super 140.2
Super 145.2
User Guide
Super 130.2 S
Super 130.2
Super 140.2
Super 145.2
128303529 b
Why compromise
Page 2
Printed in China
Copyright © 2011 Gerni
Page 3
3
Original instructions
Index
1 Safety precautions and warnings .............................................3
2 Description ...............................................................................4
3 Before you start using your pressure washer ...........................5
4 Operating your pressure washer ..............................................6
5 Fields of application and working methods ............................10
6 After using your pressure washer ...........................................12
7 Maintenance ...........................................................................13
8 Trouble shooting .....................................................................14
9 Further information .................................................................15
10 Technical Data ........................................................................18
11 Declaration of Conformity .......................................................19
1 Safety Precautions and Warnings
Before starting up
your high-pressure washer for
the fi rst time, this
instruction manual
must be read through carefully.
Save the instructions for later
use.
Safety instructions marked with
this symbol must
be observed to
prevent danger to
persons.
This symbol is
used to mark
safety instructions
that must be
observed to pre-
vent damage to the
machine and its performance.
This symbol
indicates tips
and instructions
to simplify work and to ensure
safe operation.
Do not let children or people
who have not been trained
in the use of a high pressure
washer nor read the instruction
manual ope rate the machine.
This appliance is not intended
for use by children or other
persons without assistance or
supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they do
not play with the appliance.
Before starting up your machine
please check it carefully for any
defects. If you fi nd any, do not
start up your machine and contact your Gerni distributor.
Especially check:
The insulation of the electric
cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Gerni distributor
should replace it.
WARNING!
High pressure jets can be
dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.
Never try to clean clothes or
footwear on yourself or other
persons.
Hold the spray lance fi rmly
with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope-
ration.
The operator and anyone in
the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles and protective
clothes during operation.
This appliance has been de-
signed for use with cleaning
agents supplied or recommended by the manufacturer.
The use of other cleaning
agents or chemicals may
adversely affect the safety of
the appliance.
Disconnect from electrical
power supply before carrying
out user maintenance.
To ensure the appliance
Symbols used to mark
instructions
Page 4
4
Original instructions
safety only use original spare
parts from the manufacturer
or approved by the manufacturer.
High pressure hoses, fi ttings
and couplings are important
for the safety of the appliance. Only use hoses, fi ttings
and couplings recommended
by the manufacturer.
Do not use the appliance
if a supply cord or important parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trigger gun.
Remove the plug from the
socket outlet during cleaning
or maintenance and when
replacing parts or converting
the machine to another function.
The appliance is intended for
cleaning outdoors.
Appropriate ear protection
must be used.
Never use the machine in
an environment where there
could be a danger of explosion. If any doubt arises,
please contact the local
authorities.
It is not allowed to clean
asbestos- containing surfaces
with high pressure.
WARNING! Risk of explo-
sion -Do not spray fl ammable
liquids.
Always swith off the mains
disconnecting switch when
leaving the machine unattended.
This high pressure washer
must not be used at temperatures below 0°C.
Never let any persons stand
under the product when
stored on the wall.
WARNING!
Inadequate extension cables
can be dangerous. If an extension cable is used, it shall be
suitable for outdoor use, and
the connection has to be kept
dry and off the ground. It is recommended that this is accomplished by means of a cable
reel which keeps the socket at
least 60 mm above the ground.
Cables on extension lead
drums should always be completely unwound to prevent the
cable from overheating.
Extension cables must comply
with the below-mentioned requirements for length and cable
dimensions.
1.0 mm² max. 12.5 m
1.5 mm² max. 20 m
2.5 mm² max. 30 m
If the electric cable is
damaged, it must be replaced by the manufacturer
or his service agent or similarly qualifi ed person in order
to avoid a hazard.
Mains power connection
The following should be observed when connecting the
high pressure washer to the
electric installation:
The electric installation shall
be made by a certifi ed electrician and comply with IEC
364.
It is recommended that the
electric supply to this appliance should include either a
residual current device that
will interrupt the supply if the
leakage current to earth exceeds 30 mA for 30 ms.
Water connection
Connection to the public mains
according to regulations.
Inlet hose can be connected
to the water mains with a max.
inlet pressure of 10 bar.
IMPORTANT! Only use water without any impurities. If
there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an additional fi lter should be mounted.
Safety devices
Locking device on spray gun
(7a) (see illustration at the end
of this manual):
The spray gun features a locking device. When the button is
activated, the spray gun cannot
be ope rated.
Thermal sensor:
A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sensor has cooled.
Pressure safety device
An integrated hydraulic safety
valve protects the system from
excessive pressure.
Page 5
5
Original instructions
2 Description
This high-pressure washer has
been developed for domestic
use for cleaning:
- Car, motorbike, boat,
caravan, trailer, patio/
drive/fl ag stones, wood-
work, brickwork, barbecue, garden furniture,
lawn mower
Section 5 describes the use of
the high-pressure washer for
vaious cleaning jobs.
Only use the high-pressure
washer for purposes described
in this manual.
The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.
2.2 Operation elements
and model survey
See illustration at the end of
this manual.
1 Start/stop switch
2 Water inlet (with fi lter)
3 High pressure connection
(only models without hose
reel)
4 High pressure hose
5 Electric cable
6 Click & Clean spray lance
7 Spray gun with lock
8 Click & Clean Tornado® PR
nozzle
9 Click & Clean Powerspeed®
nozzle
10 Click & Clean foam sprayer
11 Nozzle cleaning tool
12 Trolley handle (tele-scopic
handle), except 130.2 S
13 Hose reel (not standard)
14 Hose hook
15 Model tag
16 Quick coupling
17 Button for telescopic
handle, except 130.2 S
18 Turnable cable hook
Specifi cations: See model tag
(15) of machine.
We reserve the right to alter the
specifi cations.
2.1 Application
3 Before you start using your
pressure washer
3.1 Mounting of
trolley handle and hose
hook
3.1.1 Super 130.2, 140.2,
140.2 Plus
1. Push down the trolley handle
(12) over the two metal tubes.
Make sure that the handle is
mounted as illustrated. Mount
screws with nuts (make sure
that the screws go through
handle as well as tube).
2. Mount the hose hook (14)
on the machine (2 screws).
Note: the hose hook can be
mounted on the front as well
as on the back. Front position
Page 6
6
Original instructions
3.3 Mounting of quick
coupling
1. Screw the quick coupling (16)
tight on to the water inlet (2).
Note: The inlet fi lter must always be fi tted in the water inlet
pipe to fi lter out sand, lime stone
and other impurities as these
will damage the pump valves.
Caution: Failure to
fi t the fi lter will in-
validate the guar-
antee.
3.1.2 Super 130.2 S
1. Mount the trolley handle (12)
on the machine. Secure the
handle by tightening the 4
screws.
2. Mount the hose hook (14)
on the machine (2 screws).
Note: the hose hook can be
mounted on the front as well
as on the back. Front position
is to be used if the product is
used together with a special
wall hook for wall storage
(not standard).
3.2 Mounting of hose reel
handle (models with
hose reel)
1. Click the hose reel handle
on to the trolley handle (no
screws).
is to be used if the product is
used together with a special
wall hook for wall storage
(not standard 130.2 models).
Page 7
7
Original instructions
4 Operating your pressure washer
4.1 Connection of high
pressure hose (models
without hose reel)
1. Mount the high pressure
hose on the outlet (3).
3.4 Mounting of high
pressure hose
Attach the high pressure hose
(4) to the spray gun (7).
Detach the high pressure hose
by pressing the button (A).
4.2 Mounting of spray
lance and Click & Clean
nozzles
1. Push the spray lance (6) into
the spray gun (7) and twist
it until the bayonet coupling
locks into position..
Note: The
spray lance (6)
has a built-in low
pressure nozzle
that can be used for
fl ushing away dirt.
2. Attach the nozzle.
Warning: When
attaching the Click
& Clean nozzles,
the button on
the side of the spray lance
should return to the locked
position. Ensure that there is
an audible "click".
Note: The Tornado
®
PR nozzle
and the foam
sprayer feature a swivel lock,
which must be positioned in the
hole in the Click & Clean spray
lance.
Page 8
8
Original instructions
4.3 Water connection An ordinary 1/2" garden hose of
min. 10 m and max. 25 m will
be suitable.
NOTE: Connection to the public
mains according to regulations.
IMPORTANT! Only use water without any impurities. If
there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an additional fi lter should be mounted.
1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrating the machine.
Note: Check
that the fi lter is
fi tted in the water
inlet pipe and that it is clean
and free from debris.
2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 50°C).
3. Turn on the water.
4.4 Telescopic handle
(Super 130.2, 140.2,
140.2 Plus)
The machine (Super 130.2,
140.2, 140.2 Plus) features a
tele scopic handle. To raise or
lower the handle, press the
knob and move the handle upwards or downwards. When a
click is heard, the handle is in
right position.
Press the button to detach the
Click & Clean nozzle.
Page 9
9
Original instructions
4.5 Start and stop of the machine (when connected
to a water supply)
The spray lance is affected
by a thrust during operation - therefore always hold it
fi rmly with both hands. IMPOR-
TANT: Point the nozzle at the
ground.
1. Check that the machine is in
upright position.
NOTE: Do not place the ma-
chine in tall grass!
2. Release the trigger lock.
3. Activate the trigger of the
spray gun and let the water
run until all air has escaped
from the water hose.
4. Turn the start/stop switch (1)
to position "I".
5. Activate the trigger of the
spray gun.
Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
cleaned.
Do not cover the machine
during operation.
Note: If the machine is left or
not used for 5
minutes, it must be switched off
on the start/stop switch "O" (1):
1. Turn the start/stop switch to
position "O".
2. Disconnect the electrical plug
from the socket.
3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.
4. Lock the spray gun.
When releasing the trigger of
the spray gun, the machine
automatically stops. The machine will start again when you
re-activate the spray gun.
the water and then connect
the hose to the machine with
the quick coupling and fi nally
uncrimp the water inlet hose.
2. Turn the start/stop switch to
position "I".
3. Activate the trigger of the
spray gun with lance and
nozzle removed and let the
water run, until the air has
escaped from the water hose
and the pump.
4. Mount spray lance and
nozzle.
The washer can draw water
from a rain water tank or bucket
as an example. The hose for the
water supply must not be too
long, approx. 5 m.
Make sure that the water tank is
not placed on a lower level than
the machine.
Use an external fi lter if the water contains impurities.
1. Make sure that the water
hose is fi lled completely with
water before connecting to
the machine. Place the entire
hose in a tank or bucket. To
avoid water spillage, crimp
the water inlet hose down in
4.6 Start the machine (when
connected to open containers (suction mode))
Page 10
10
Original instructions
4.7 Pressure regulation on
the TORNADO® PR-nozzle
The pressure can be regulated
on the TORNADO® PR nozzle.
4.8 Stationary use If mounting a special wall hook
(not standard), the pressure
washer can be used as a stationar
y solution meaning that it
can be operated while hanging
on the wall.
Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawlplugs to the type of wall.
On the wall hook garden/rim
brush (a) foam sprayer (b),
Click & Clean brush (c) and
Click & Clean nozzles (d) can
be stored.
Important: The bearing capa-
city of the wall
hook is max. 30 kg.
Lavtryk
Højtryk
High pressure
Low pressure
Page 11
11
Original instructions
5 Fields of application and
working methods
5.1 General Effi cient high presure cleaning is achieved by following a few guide-
lines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly chosen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.
5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the
chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surface that has to be cleaned can be da maged.
5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical
effect may be required. Special wash brushes offer this supplementary effect that cuts through dirt (especially by car washing).
Page 12
12
Original instructions
5.2 Typical fi elds of application
Below you will fi nd a description of a lot of cleaning tasks which can be solved by a pressure washer
from Gerni in association with accessories and detergents.
Task Accessories ‘Click
& Clean’
Cleaning method
Car
Car nozzle,
auto brush,
underchassis
nozzle,
Foam sprayer,
Neutral car wash
1. Apply neutral car wash with the foam sprayer. Always start
from the bottom and work upwards. Let neutral car wash act
for at least 5 min.
2. Wash the car with the car nozzle, which has been optimized for
quick and gentle cleaning of enamelled surfaces (the jet is wider
and not so sharp). Start at the front of the car and work backwards to avoid water from penetrating via the door seals.
3. Use the brush for removal of traffi c fi lm which is not removed by the
nozzle. If the car is very dirty, apply neutral car wash again.
4. Attach the undercarriage nozzle and clean undercarriage and
wheel arches.
5. Remove water from the surface of the car with the squeegee
on the car brush. Make sure that all grains of sand etc. have
been removed before using the squeegee. Wipe with a wash
leather where the squeegee cannot reach.
Rims, alu-
minium
Rim brush,
auto nozzle,
atomizer,
alloy cleaning
agent
Apply alloy cleaning agent with an automizer. Let it act for approx.
5 min. and wash with the rim brush. For steel rims, use neutral
car wash. Use the foam sprayer and wash with rim brush.
Be careful! The high pressure jet may damage the tyres.
Flag-
stones,
concrete
fl oors and
other hard
surfaces
Powerspeed®
nozzle,
neutral detergent,
Patio Cleaner
Wash towards outlets or the like. On surfaces with moss or al-
gae you may start by applying Neutral detergent with the foam
sprayer. Wash before the soap dries. Another more effective and
quicker method is to use the Patio Cleaner. Thus you will also
avoid splashes.
Garden
furniture,
wood
Wood Cleaner
Garden brush
Apply Wood Cleaner and wash before the soap dries.
NOTE: Use the garden brush to clean off the dirt.
Brickwork,
Wood
work
Powerspeed®
nozzle,
neutral detergent,
Patio Cleaner
Same method as for fl agstones, but be careful - bad joints and
wood may be damaged by high pressure. You may choose only
to use the Tornado® nozzle. Adjust the distance (pressure) to
the quality of the joints and the wood. Patio Cleaner can also be
used on vertical surfaces.
Gutter
Underchassis spray
lance
Wash the gutter with the nozzle. Always wash towards
downpipes. Beware not to spray under the roofi ng.
Cleaning
of drain
pipes, outlets, down
pipes etc.
Tube cleaner Push the tube cleaner approx. ½ m (to mark) into a tube or drain
and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and fl ush the dirt backwards.
Rust, paint
Water/sandblasting
equipment
Mount the water/sand blasting equipment and rust and paint
is effi ciently and quickly removed. Beware not to damage the
surface to be sandblasted.
Green-
house
Tornado® PR nozzle
brush, neutral de-
tergent
Wash with high pressure and maybe a brush. You may use neu-
tral detergent to remove moss and algae.
Garden
tools,
lawn
mower
Tornado® PR
nozzle, Powerspeed® nozzle,
multiangle adaptor,
degreaser
Rinse the worst dirt off with the nozzle. Apply degreaser with
the foam sprayer and let it act for approx. 5 min. Wash with the
nozzle. You may use the multiangle adaptor for hard to get at
areas to avoid splashing.
Page 13
13
Original instructions
6 After using your pressure washer
6.2 Winding up of electric
cable and high pressure
hose
up carefully.
1. Wind up the electric cable on
the appropriate hooks. A built
in clip secures the cable (1).
The lower hook can be
turned to release the electric
cable.
2. The high pressure washer
comes in two models: A) with
hook for storage of high pressure hose (14) - B) with a
hose reel (13).
6.1 Storing the washer The machine should be sto-
red in a frost-free room!
Pump, hose and accessories
should always be emptied of
water prior to storing as follows:
1. Stop the machine (turn the
start/stop switch (1) to position “O” and detach water
hose and accessory.
2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
gun.
3. Stop the machine, unplug
and wind up hose and cable.
4. Place spray handle, nozzles
and other accessories in the
holders of the machine.
Should the machine by mistake
be frozen, it will be necessary
to check it for damage.
NEVER START-UP A FROZEN
MACHINE.
Frost damages are not
covered by the guarantee!
To avoid accidents, the electric
cable and the high pressure
hose should always be wound
b
c
d
e
f
a + f
d
c
b
e
6.3 Storage of accessories
The standard accessories
(spray gun (f), spray lance (a),
nozzles (b) foam sprayer (c))
can be stored on the pressure
washer.
The nozzle cleaning tool (d)
and a Click & Clean brush
(e) can also be stored on the
product.
Page 14
14
Original instructions
WARNING! Always disconnect
the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:
Wash off water hose, high
pressure hose, spray lance
and accessories before
mounting.
Clean the connectors of dust
and sand. Make sure that
no sand or dirt is blocking
the movement of the button
on the Click & Clean spray
lance.
Rinse the detergent spraying
attachment after use.
Clean the nozzles.
Any repair should always be
made in an authorized workshop with original spare parts.
7 Maintenance
7.1 Cleaning of water
inlet fi lter
Clean the water inlet fi lter regularly once a month or more frequently according to use. Carefully loosen the fi lter with a pair
of pliers and clean it. Check that
it is intact before re-mounting it.
The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out sand, limestone and
other impurities, as they will
damage the pump valves.
CAUTION: Failure to fi t the fi lter
will invalidate the guarantee.
7.2 Cleaning of nozzle A clogging up in the nozzle
causes a pump pressure which
is too high. This is why cleaning
is required immediately.
1. Stop the machine and disconnect the nozzle.
2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!
3. Flush the nozzle backwards
with water.
7.3 Cleaning of machine
vents
The machine should be kept
clean so as to let cooling air
pass freely through the machine vents.
Page 15
15
Original instructions
8 Trouble Shooting
Please ensure that you check the following before contacting the Gerni service organization:
Symptom Cause Recommended action
Machine refuses to Machine not plugged in Plug in machine.
start Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the extension cable.
Fluctuating pressure Pump sucking air Check that hoses and connections are air-
tight.
Motor hums Low voltage or Activate the trigger of the spray gun.
low temperature
Machine stops Fuse has blown Replace fuse. Switch off other machines.
Incorrect mains voltage Check that the mains voltage corresponds
to specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool
down.
Nozzle partially blocked Clean the nozzle (see section 7.2)
Fuse blows Fuse too small Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.
Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger
until regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds
mains water to specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min.
1/2")
Nozzle partially blocked Clean the nozzle (see section 7.2)
Water fi lter blocked Clean the fi lter (see section 7.1)
Hose kinked Straighten out hose.
Machine often starts Pump/spray gun is Contact your nearest Gerni Service
and stops by itself leaking Centre.
Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen
No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 7.1)
Nozzle blocked Clean the nozzle (see section 7.2)
In case problems other than the above occur, please phone 1300 733 171 or check our website
www.gerni.com.au for your nearest service agent.
7.4 Greasing of couplings
To ensure easy connection and
that o-r
ings do not dr
y up, the
couplings should be greased
regularly.
Page 16
16
Original instructions
9 Further information
9.1 Recycling the washer Make the old cleaner unusable
immediately.
1. Unplug the cleaner and cut
the electric cable.
Do not discard electrical appliances with household waste.
As specifi ed in European Direc-
tive 2002/96/EC on old electrical and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.
Contact your local authorities or
your nearest dealer for further
information.
9.2 Warranty conditions Our goods come with guaran-
tees that cannot be excluded
under the Australian Consumer
Law. You are entitled to a replacement or refund for a major
failure and for compensation for
any other reasonably foreseeable loss or damage. You are
also entitled to have the goods
repaired or replaced if the
goods fail to be of acceptable
quality and the failure does not
amount to a major failure.
Gerni high-pressure washers
for domestic use are warranted
for 2 years from the date of
purchase by:
AUSTRALIA:
Nilfi sk-Advance Pty LTd
Unit 1/13 Bessemer Street
Blacktown NSW 2148
Phone: 1300 556 710
E-mail: sales@gerni.com.au
NEW ZEALAND:
Accent Tools Ltd
232 Bush Rd
Albany
Auckland 0632
Phone: 09 968 2610
E-mail:
sales@accent-tools.co.nz
Equipment defects covered by
this warranty will be repaired or
replaced by one of the service
centres of the Gerni organisation. Find your local service
agent here:
http://www.gerni.com.au/.
If your high pressure washer or
ac ces so ries are handed in for
repair, it must be followed by a
description/spe ci fi ca ti on of the
fault, and the original purchase
receipt, or a copy, must be enclosed.
Packing and postage/carriage is
not covered by the warranty.
The bene fi ts under this warranty are in addition to your
national law of sale.
Guarantee repairs are made on
the following con dit ions:
that defects are attributable
to fl aws or defects in materials or workmanship. (wear
and tear as well as misuse
are not covered by the
gu a ran tee).
that the directions of this
instruction manual have been
thoroughly observed.
that repair has not been
carried out or attempted by
other than Gerni-trained service staff.
that only original accessories
have been applied.
that the product has not been
exposed to abuse such as
knocks, bumps or frost.
that only water without any
impurities has been used.
Page 17
17
Original instructions
9.3 Accessories
Only use original accessories.
Click & Clean
Car nozzle
Special nozzle for enameled surfaces. Optimal distance: 30 50 cm.
Click & Clean
Undershassis
nozzle
90° angled special nozzle for undercarriage and wheel arches.
Integrated guide shoes.
Click & Clean
Brushes
For cars and other surfaces. Available in more shapes.
Extension hose
7 m extension hose increasing the working range.
Drain & Tube
cleaner
15 m long tube cleaner for the cleaning of tubes and drains.
Water-sandblasting equipment
For removal of paint and rust. Sand available from do-it-yourself shops.
Patio Plus
Equipment for quick cleaning of patio/drive/fl agstones.
that the high pressure wash-
er has not been used for
rental nor used com mer cial ly
in any other way.
Repairs not covered by the
guarantee conditions will be
invoiced. (i.e. malfunctions due
to Causes men ti o ned in section Trouble Shooting of the
instruction manual).
Please phone 1300 733 171
(Australia) or 09 9682610
(NZ) for service or warranty assistance only after
checking possible causes
in the trouble shooting
chart on page 15.
Page 18
18
Original instructions
10 Main Technical Data
Type Super 130.2 Super 140.2 Super 145.2
Electrical Specification
Rated voltage V 230-240
230-240 230-240
Rated frequency Hz 50 50 50
Rated power consumption kW 2.1 2.1 2.1
Current A 9.0 9.0 9.0
Protection class
Class I/
Class II
Class I Class I Class I
Protection degree IP XX IPX5 IPX5 IPX5
Hydraulic specification
Rated pressure MPa/bar 12.5/125 13.5/135 14/140
Max. pressure MPa/bar 13/130 14/140 14.5/145
Rated water flow l/min/l/hr 7.5/450 7.0/420 6.8/410
Max. water flow l/min/l/hr 8.3/500 8.3/500 8.3/500
Max. water inlet pressure Mpa/bar 1/10 1/10 1/10
Max. water inlet temperature °C 60 60 60
Max. water inlet temp. suction mode °C 20 20 20
Weight kg 17.7 18.9 20.2
Hand-arm vibration according to ISO
5349-1:
Standard nozzle m/s
2
< 2.5 ±1 < 2.5 ±1 < 2.5 ±1
Sound pressure level L
pA
in accordance
with ISO 3744
dB(A) 69.9 ±2 69.9 ±2 71.5 ±2
Guaranteed sound power level L
WA in
accordance with 2000/14/EC
dB(A) 84 84 86
Page 19
19
Original instructions
11 Declaration of Conformity
Declaration of Conformity
Product:
High Pressure Washer
Type:
Gerni Super 130.2 S, Super 130.2,
Super 140.2, Super 140.2 Plus, Super 145.2 Plus
Description:
230-240 V 1~, 50 Hz - IP X5
The design of the unit corre sponds to the following pertinent regulations:
EC Machine Directive
2006/42/EC
EC Low-voltage Directive 2006/95/EC
EC EMC Directive 2004/108/EC
Applied harmonised standards:
EN 60335-2-79
Applied national standards and technical specifi -
cations:
IEC 60335-2-79
Name and address of the person autho rised to
compile the technical fi le:
Anton Sørensen
General Manager, Technical Operations EAPC
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Identity and signature of the person empowered
to draw up the declaration on behalf of the manufacturer:
Anton Sørensen
General Manager, Technical Operations EAPC
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Place and date of the declaration
Hadsund, September 1, 2011
Page 20
Super 130.2 S
Super 130.2
Super 140.2 / 140.2 Plus
Page 21
AUSTRALIA:
Nilfi sk-Advance Pty Ltd
Unit 1/13 Bessemer Street
Blacktown NSW 2148
Phone: 1300 556 710
E-mail: sales@gerni.com.au
NEW ZEALAND:
Accent Tools Ltd
232 Bush Rd
Albany
Auckland 0632
Phone: 09 968 2610
E-mail: sales@accent-tools.co.nz
Loading...