GermanPool EF-116W User Manual

Multi-Oscillation Electric Fan - Wall-Mount Type

多向環迴電風扇–掛牆式

EF-116W

在使用之前請詳細閱讀 「使用說明書」及「保用條例」，並妥為保存。

Please read these instructions and warranty information carefully
before use and keep them handy for future reference.

Product Structure

Assembly Instructions

- Basic Operation

- Tilt Angle Adjustment

- Oscillation Settings

Care & Maintenance

04

05

Operating Instructions

06

Technical Specifications

07

07

Warranty Terms & Conditions

15

Notice Before Use

03

Table of Contents

Notice Before Use

Important

- For safety purpose, you should read the instructions carefully before using the appliance for the rst time. Save
the instructions for future reference.

- The appliance is designed for domestic use and may only be operated in accordance with this instruction manual.

1. Ensure that the fan is switched off from the supply mains before removing the grille.

2. Do not place the product in or near an open window. Rain, snow and other weather conditions may create an

electrical hazard.

3. Always operate the product on a at, steady and stable wall surface.

4. Do not hang the product in the air. Always use it on a dry, at wall surface.

5. Always unplug product from power socket when it is not in use.

6. Always unplug the product with a dry hand.

7. Never insert ngers or any other object through the Fan Grilles.

8. Do not operate product if the cord is cut, damaged or if the wires are exposed.

9. Do not immerse or expose the Motor Cover, Power Cord, or plug to water or other liquids.

10. If using an extension cord with this product, the electrical rating of the extension cord should be at least as great

as the rating of the product.

11. Do not operate the product if the Power Cord or plug malfunctions, is dropped and/or is damaged.

12. This household product is intended for indoor, non-industrial use only. Do not use in the outdoors.

13. Ensure that the product is fully assembled before plugging it into an electrical outlet.

14. Assemble and disassemble product parts with care. Otherwise, serious injuries and/or property damage may result.

15. This product is not intended to be operated by persons (including children) with reduced physical, sensory or

mental capabilities or lack of experience and knowledge unless they are supervised and/or instructed by a

person responsible for their safety.

16. Children should be supervised to ensure that they do not play with the appliance.

17. If the supply cord is damaged, it must be replaced by a German Pool technician or a licensed electrician in order

to avoid a hazard.

18. To reduce the risk of re or electric shock, do not use this fan with any unauthorized speed control device.

Environmental Tips

- Do not dispose this product as unsorted municipal waste. Collect and dispose such waste
separately according to your local environmental regulations.

- In most cases, you can discharge the appliance at your local recycling center.

P.3

Product Structure

Blades & Grille

(1) Name Plate (5) Blade Cap (6) Fan Blades (7) Grille Connector

Motor & Arm

(10) Oscillation Knob

(Up-Down)

(12) Motor Shaft

(2) Front Grille

(4) Grille Lock

(3) Grille Ring (8) Rear Grille

(11) Oscillation Knob
(Left-Right)

(9) Motor Housing

(13) Fan Arm

(14) Speed Knob

(13) Unit Base

(17) Mounting Plate

(18) Screws

(16) Pull Switch

P.4

Assembly Instructions

Installing Grille & Blades

1. Loosen the Grille Connector (7) from the Motor Housing (9) (refer to arrows inscribed on the Grille Connector).

2. Place the Rear Grille (8) onto the Motor Shaft (12).

Note

Align the grille openings with the 3 molded pegs on the faceplate of the Motor Housing (9).

3. Place the Grille Connector (7) back onto the Motor Shaft (15) and carefully tighten it.

4. Attach the Fan Blades (6) onto the Motor Shaft (15) and x it with the Blade Cap (5).

Note

Ensure the edge of the Motor Shaft (15) aligns with the hole of the Fan Blades (6).

5. Connect the Front and Rear Grilles (2 & 8) with Grille Lock (4).

Mounting Unit Base

1. Fix the Mounting Plate (17) on the wall by three Screws (18).

2. Make sure the Mounting Plate (17) is securely and tightly xed on the wall.

3. Attach the back of the Unit Base (15) to the Mounting Plate (17).

P.5