German ElectroniX ZAGIL Operation Manual & User Manual

ZAGIL GSM/GPRS MODEM

OPERATION MANUAL

MANUAL

1

Operation Manual

User Guide

GERMAN ELECTRONIX

ZAGIL GSM/GPRS MODEM User Guide

© German ElectroniX

Erzgiessereistr. 39 b in 80335

Munich / Germany

Tel: [phone]

Fax: [phone]

Table of Contents

Package Content ....................................................................... 1

Features .................................................................................... 1

Specifications ............................................................................ 2

Installation ................................................................................. 3

Basic Operation ......................................................................... 4

GERMAN ELECTRONIX

Package content

1. ZAGIL GSM MODEM Terminal.

2. FS socket fixed with Flat cable 20cm.

3. Female connector for Supply.

4. Serial Cable.

5. User manual

Fea tures

Quad-band GSM

Desktop ABS case

Industrial standard design and quality guarantee

Side mounting

RS232 Serial interface

TTL Interface

Status LED Power/GSM/Call

Based on simcom340 module

AT commands

Compatible with Microchip circuits “TTL logic interface”.

1

GERMAN ELECTRONIX

Specifications

Frequency
bands

- Tri-band: EGSM 850, 900, DCS 1800, PCS 1900. The MODEM can search the 4
frequency bands automatically. The frequency bands also can be set by AT COMMAND.

- Compliant to GSM Phase 2/2+
GSM class Small MS
Transmit

power
GPRS
connectivity

- Class 4 (2W) at EGSM900

- Class 1 (1W) at DCS1800 and PCS 1900

- GPRS multi-slot class 10 （default）

- GPRS multi-slot class 8 (option)

- GPRS mobile station class B

DATA GPRS:
CSD:

- GPRS data downlink transfer: max. 85.6 kbps

- GPRS data uplink transfer: max. 42.8 kbps

- Coding scheme: CS-1, CS-2, CS-3 and CS-4

- supports the protocols PAP (Password Authentication Protocol) usually used for PPP

connections.

- Integrates the TCP/IP protocol.

- Support Packet Switched Broadcast Control Channel (PBCCH)

- CSD transmission rates: 2.4, 4.8, 9.6, 14.4 kbps, non-transparent

- Unstructured Supplementary Services Data (USSD) support
SMS - MT, MO, CB, Text and PDU mode

- SMS storage: SIM card

- Support transmission of SMS alternatively over CSD or GPRS. User can choose

preferred mode.
FAX Group 3 Class 1
Phonebook

Support phonebook types: SM, FD, LD, RC, ON, MC.
management
SIM interface Support SIM card: 1.8V ,3V
External

Connected via 50 Ohm antenna connector or antenna pad
antenna
Serial interface Autobauding supports baud rate from 1200 bps to 115200bps.

TTL interface "low" when between 0 V and 0.8 V

"high" when between 2.2 V and 5 V

IDC socket 10 pin
Antenna

SMA female, GSM 50Ω antenna included

connector
LED indication

Green: power ON Red: GSM status Yellow: Incoming call

Power supply Single supply voltage 5VDC
Power saving Typical power consumption in SLEEP mode to 3.5mA ( BS-PA-MFRMS=5 )
Temperature
range

- Normal operation: -20°C to +55°C

- Restricted operation: -30°C to -20°C and +55°C to +80°C
Case type ABS desktop , wall mounting
Supply

Screw connector 2.5 mm
connector
Dimension
Weight

155mm*85mm*46mm

200g

2

Interfaces

1 Serial port RS232
1 TTL Voltage level Socket “FC10”
Power supply（DC 5V、500mA）
Antenna interface
Status lights, Green light indicate power status
SIM Card Holder

.

FIGURE 1 TTL FC10 socket,

Serial Port, Power supply socket

Installation

a) Open the SIM card holder,
insert in a valid SIM Card
provided by GSM network
operator or Service provider.

b) Install the GSM Modem to
your location and connect the
antenna to the SMA connector.

c) Fix the serial cable to the GSM modem, the supplied
cable will connect the unit to a PC. For other devices you
may need a crossover cable.

d) Connect the GSM Modem power supply interface
with the power adapter’s output jack, and then connect
the adapter to its power supply source.

Make sure that all connections are properly

3

TTL socket description

You supply the modem throw FC10 socket as it shown in figure 4 so no need to
supply it from 2.5 connector

Basic Operation

A. Module connection with Hyper Terminal.

1. Establish or Open Hyper Terminal from All Programs > Accessories>

Communications and setting up relevant parameters. Module baud rate is 115200.

(1). Establish connection.

4

(2). Setting up usage port.

(3). Setting up port parameters.

5

(4). Setting up property in File Menu of Hyper Terminal

6

7

2. You can input word “AT” then press “Enter” key, it should be response word “OK” means
work
Property. All commands are executed by pressing “Enter” key.

8