Gericom SuperSonic Extrem HD P55IM1 User Manual

i

i

Preface

©

©Copyright 2007

All Rights Reserved.
The information in this document is subject to change without prior

notice in order to improve reliability, design and function and does
not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect,
special, incidental, or consequential damages arising out of the
use or inability to use the product or documentation, even if
advised of the possibility of such damages.

This document contains proprietary information protected by
copyright. All rights are reserved. No part of this manual may be
reproduced by any mechanical, electronic, or other means in any
form without prior written permission of the manufacturer.

Limitation of Liability

While reasonable efforts have been made to ensure the accuracy
of this manual, the manufacturer and distributor assume no liability
resulting from errors or omissions in this manual, or from the use of
the information contained herein.

Notices

Federal Communications Commission Radio Frequency
Interference Statement

This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction
manual may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

ii

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected
Consult the dealer or an experienced radio TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.

Notice:

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment. Shielded interface cables and a non­shielded AC power cord must be used in order to comply with
emission limits.

This equipment is to be used with power supply:
120W
There is no internal power supply.

iii

Table of Content

1. BEFORE YOU START ...........................................................................1

LET YOUR COMPUTER ACCLIMATE ITSELF ..............................................8

HEAT, COLD, HUMIDITY, AND GLARE ....................................................8

SUITABLE PLACE TO WORK...................................................................9

2. INTRODUCTION..................................................................................11

OPENING THE LCD PANEL .................................................................11

FRONT VIEW .....................................................................................12

LEFT VIEW ........................................................................................14

RIGHT VIEWS ....................................................................................14

REAR VIEWS .....................................................................................15

BOTTOM VIEW...................................................................................16

3. GETTING STARTED............................................................................17

CONNECTING THE AC ADAPTER .........................................................17

TO REMOVE THE BATTERY PACK: ......................................................19

TO INSTALL THE BATTERY PACK:........................................................19

4. USING THE NOTEBOOK COMPUTER....................................................21

LCD CARE........................................................................................21

EXTERNAL CRT DISPLAY...................................................................21

FUNCTION KEYS (QUICK KEYS)..........................................................22

TOUCHPAD PRECAUTIONS.................................................................22

FEATURES OF THE DVD DUAL ...........................................................22

PRECAUTIONS FOR HANDLING CD DISCS ...........................................23

LOADING A DISC ................................................................................23

THE BATTERY POWER SYSTEM ..........................................................24

PREPARING THE BATTERY PACK FOR USE (BATTERY CALIBRATION) ....25

AUTOMATIC BATTERY PACK CHARGING FUNCTION..............................25

BATTERY STATUS..............................................................................26

BATTERY LOW WARNING ...................................................................26

SMALL BATTERY FOR THE REAL TIME CLOCK......................................26

HELP WINDOWS ................................................................................28

DESKTOP ..........................................................................................28

5. DESKTOP OPERATION.......................................................................33

iv

THE MULTIMEDIA SOUND SYSTEM......................................................33

AUDIO VOLUME CONTROL..................................................................34

AUDIO SOFTWARE .............................................................................34

SOUND RECORDING ..........................................................................34

PLAYING SOUND FILES ......................................................................34

EXTERNAL SPEAKERS AND MICROPHONE ...........................................34

6. INTERNET CONNECTION.....................................................................35

7. RUNNING BIOS SETUP .....................................................................39

INFO .................................................................................................40

MAIN SETUP .....................................................................................41

ADVANCED SETUP.............................................................................41

SECURITY .........................................................................................42

POWER .............................................................................................42

BOOT SETUP.....................................................................................43

EXIT SETUP ......................................................................................43

8. VGA UTILITIES .................................................................................45

DISPLAY MANAGER ...........................................................................46

DISPLAY OPTIONS .............................................................................47

NOTEBOOK PANEL PROPERTIES.........................................................48

COLOR .............................................................................................49

VIDEO...............................................................................................50

POWERPLAY ..................................................................................... 52

9. VIDEO CONFERENCING (OPTIONAL)...................................................53

SNAPSHOT COMMAND .......................................................................54

RECORD COMMAND...........................................................................54

PROPERTY COMMAND .......................................................................55

SETTING COMMAND...........................................................................56

10. TROUBLESHOOTING ........................................................................57

NO SPEAKER OUTPUT - ......................................................................58

SOUND CANNOT BE RECORDED - ........................................................58

THE HARD DISK DRIVE DOES NOT WORK OR IS NOT RECOGNIZABLE .......59

THE HARD DRIVE IS MAKING ABNORMAL WHINING NOISES .....................59

THE HARD DISK DRIVE HAS REACHED ITS CAPACITY .............................59

THE HARD DISK TAKES LONGER TO READ A FILE...................................60

v

THE FILES ARE CORRUPTED ...............................................................60

THE OPTICAL DRIVE DOES NOT WORK .................................................60

THE DRIVE DOSE NOT READ ANY DISKS ...............................................60

THE DISK CANNOT BE EJECTED...........................................................60

THE COMBO OR DVD RW DRIVE CANNOT RECORD .............................60

THE DISPLAY PANEL IS BLANK WHEN THE SYSTEM IS TURNED ON ..........61

THE SCREEN IS DIFFICULT TO READ - ..................................................61

THE SCREEN FLICKERS - ....................................................................61

THE BUILT-IN TOUCH PAD PERFORMS ERRATICALLY - ...........................61

THE BUILT-IN KEYBOARD ACCEPTS NO INPUT -.....................................61

THE CHARACTERS ON THE SCREEN REPEAT WHILE I TYPE. ...................61

A MESSAGE “CMOS CHECKSUM FAILURE” DISPLAYS DURING THE

BOOTING PROCESS OR THE TIME

(CLOCK) RESETS WHEN BOOTING .......62

THE POST DOES NOT SHOW AN INCREASED MEMORY CAPACITY WHEN

YOU HAVE ALREADY INSTALLED ADDITIONAL MEMORY

..........................62

THE O/S ISSUES AN INSUFFICIENT MEMORY ERROR MESSAGE DURING

OPERATION

.......................................................................................62

PC CARDS DO NOT FUNCTION-...........................................................62

THE PC CARD CANNOT BE RECOGNIZED - ...........................................63

WINDOWS CRASHES OR FREEZES WHEN YOU REMOVE THE PC CARD-..63

THE COMPUTER BECOMES HOT - ........................................................63

THE PROGRAM APPEARS STOPPED OR RUNS VERY SLOWLY - ...............63

THE USB DEVICE DOES NOT WORK - ..................................................64

A. SPECIFICATION.................................................................................65

1

BBeeffoorree yyoouu SSttaarrtt

Conventions of This Manual

Use this manual will help you get the most from your notebook
computer.

• If you are an experienced user of computers and/or Microsoft’s

Windows operating systems, you might find it useful to read the
Quick Start Guide that comes along with your accessories.

• If you are a less experienced user, you should through the

manual carefully before using your system.

Whether or not you are an experienced user, you should consult
on the Troubleshooting Chapter if you encounter any problems
with your notebook.

This product incorporates copyright
protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright
protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.

Safety Precautions

This section is designed to assist you in identifying potentially
unsafe conditions while working with this product. Required safety
features have been installed in the computer to protect you from
injury. However, you should use good judgment to identify potential
safety hazards:

1. Please read these safety instructions carefully.

2. Please keep this User's Manual for later reference.

2

3. Please disconnect this equipment from AC outlet before

cleaning. Don't use liquid or sprayed detergent for cleaning.
Use moisture sheet or cloth for cleaning.

4. For pluggable equipment, that the socket-outlet shall be

installed near the equipment and shall be easily accessible.

5. Please keep this equipment from humidity.

6. Lay this equipment on a reliable surface when installed. A

drop or fall could cause injury.

7. Make sure to use the right voltage for the power source when

connecting the equipment to the power outlet.

8. Place the power cord in such a way that people can not step

on it. Do not place anything on top of the power cord.

9. All cautions and warnings on the equipment should be noted.

10. If the equipment is not use for a long time, disconnect the

equipment from the main power outlet to avoid being damaged
by transient overvoltage.

11. Never pour any liquid into the opening, this could cause fire or

electrical shock.

12. Never open the equipment. For safety reason, the equipment

should only be opened by a qualified service personnel.

13. If on the following situations arises, get the equipment

checked by a service personnel:

a. The Power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment has not worked well or you cannot get it

work according to the user's manual.

e. The equipment has dropped and damaged.
f. If the equipment has obvious sign of breakage.

14. Do not leave this equipment in an environment unconditioned,

storage temperature above 60°C (140°f), it may damage the
equipment.

15. The unit can be operated at an ambient temperature of max.

35°C.

16. The sound pressure level at the operators position according

to IEC 704-1: 1982 is equal or less than 70 dB(A).

17. Power Cord Requirements

The power cord set used with the AC adaptor must meet the
requirements of the country where you use the AC adaptor,
whether it is 100-120 or 200-240 Vac. The following
information explains the requirements for power cord set

3

selection.

 The cord set must be approved for the country in

which it is used.

 The appliance coupler must have a configuration

for mating with a CEE22/EN6032/IEC 320
appliance inlet.

A. For U.S. and Canada:

 The cord set must be UL Listed and CSA

Certified.

 The minimum specifications for the flexible cord

are No. 18 AWG.

B. For Japan:

 All components of the cord set must bear a

“PSE” or “ T ” mark and registration number in
accordance with the Japanese Dentori Law.

 The minimum specifications for the flexible cord

are .75m ㎡ conductors.

C. For Other Countries:

 The cord set fittings must bear the certification

mark of the agency responsible for evaluation in
a specific country.

 The flexible cord must be of a HAR (harmonized)

type H03VV-F.

 The cord set must have a current capacity of a

least 2.5 Amperes and voltage rating of 125 or
250 Vac.

CAUTION: MODEL P55IMx(x=0~9) IS DESIGNED TO USE WITH
THE FLLOWING AC ADAPTER MODEL ONLY

Manufacturer: LISHIN INTERNATIONAL ENTERPRISE CORP.
Manufacturer: Delta

18. When using your telephone equipment, basic safety

precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons. These precautions
includes the following:

¾ Do not use this product near water, for example, near a

bathtub, washbowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.

¾ Avoid using a telephone (other than a cordless type)

during an electrical storm. There may be a remote risk
of electric shock from lightning.

4

¾ Do not use the telephone to report a gas leak in the

vicinity of the leak.

¾ Use only the power cord indicated in this manual.

19. Do not use the AC adapter near open water or other liquids.

Never spill liquid into the AC adapter.

20. Laser Warning: Laser Class I Product Caution - Invisible laser

radiation when open avoid exposure to beam.
The optical drive used with this computer is certified as a
Class1 laser device according to the U.S. Department of
Health and Human Services (DHHS) Radiation Performance
Standard and International Standards IEC 60825-1 (EN60825-

1). The device is not considered harmful, but the following
precautions are recommended:

¾ Do not open the unit.
¾ Avoid direct exposure to the laser beam.
¾ If the unit requires service, contact an authorized

service center.

¾ Ensure proper use by reading and following the

instructions carefully.

¾ Do not attempt to make any adjustment of the unit.

Class 1 Laser Product
Appareil A Laser De Classe 1
Laserschutzklasse 1 Produkt

Do not attempt to disassemble
the cabinet containing the laser. The laser beam used in this
product is harmful to the eyes. The use of optical instruments,
such as magnifying lenses, with this product increase the
potential hazard to your eyes. For your safety, have this
equipment serviced only by an authorized service provider.

21. Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer's instructions. Never remove the battery pack
while the power is on as this may result in data loss when the
system loses power.

22. The input receptacle is used as the main disconnecting device.

5

23. Note to CATV System Installer – This reminder provided to

call the CATV system installer’s attention to Section 820-93 of
the National Electric Code which provide guidelines for proper
grounding and in particular, specify that the Coaxial cable
shield shall be connected to the grounding system of the
building, as close to the point of cable entry as practical

This part is hot. Be careful.

Diese Flachewird sehr heiss.

When you see this symbol, be careful as this spot may be
very hot.

Wichtige Sicherheitshinweise

1. Bitte lesen Sie diese Hinweis sorgfältig durch.

2. Heben Sie dirse Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen.

Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am
besten eignet sich ein angefeuchtetes Tuch zur Reinigung.

4. Die Netzanschluβsteckdose soll nahe dem Gerät angebracht

und leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu

achten. Ein Kippen oder Fallen könnte Beschädigungen
hervorrufen.

7. Beachten Sie beim Anschluß an das Stromnet die

Anschlußwerte.

8. Verlegen Sie die Netzanschlußleitung so, daß niemand

darüber fallen kann. Es sollte auch nichts auf der Leitun
abgestellt werden.

9. Alle Hinweise und Warnungen, die sich am Gerät befinden,

sind zu beachten.

10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt,

sollten Sie es vom Stromnetz trennen. Somit wird im Falle
einer Überspannung eine Beschädigung vermieden.

11. Durch die Lüftungsöffnungen dürfen niemals Gegenstände

oder Flüssigkeien in das Gerät gelangen. Dies könne einen
Brand bzw. Elektrischen Schlag auslösen.

12. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen

der elektrischen Sicherheit nur von authorisiertem

6

Servicepersonal geöffnet werden.

13. Wenn folgende Situationen auftreten ist das Gerät vom

Stromnetz zu trennen und von einer qualifizierten Servicestelle
zu Überprüfung.:

aa..

Netzlabel oder Netzstecker sind beschädigt.

bb..

Flüssigkeit ist in das Gerät eingedrungen.

cc..

Das Gerät war Feuchtigkeit ausgesetzt.

dd..

Wenn das Gerät nicht der Bedienungsanleitung

entsprechend funktioniert oder Sie mit Hilfe dieser
Anleitung keine Verbesserung erzielen.

ee..

Das Gerät ist gefallen und/oder das Gehäuse ist

beschädigt.

ff..

Wenn das Gerät deutliche Anzeichen eines Defektes

aufweist.

14. VORSICHT: Explosiongsgetahr bei unsachgemäßen

Austausch der Batterie. Ersatz nur durch denselben oder
einem vom Hersteller empfohlenem ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben des
Herstellers.

15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von

maximal 35ºC.

16. Die Ausgangswerte dürfen nicht die auf dem Label

angegebenen Werte überschreiten.

17. Anforderungen an das Stromkabel

Das Kabel-Set, das an das Netzteil angeschlossen wird, muss
den Anforderungen des Landes, in dem Sie das Netzteil
einsetzen, genügen, je nachdem, ob die Netzspannung 100­120 oder 200-240V Wechselspannung beträgt.

 Das Kabel-Set muss für das Land, in dem es

eingesetzt wird, zugelassen sein.

 Der Gerätestecker des Kabels muss in eine

CEE22/ EN603/IEC 320 Buchse passen.

A. Für die USA und Kanada:

 Das Kabel-Set muss UL-gelistet und CSA

zertifiziert sein.

 Die Minimalanforderungen für das Kabel

entsprechen No. 18 AWG.

B. Für Japan:

7

 Alle Teile des Kabel-Sets müssen entsprechend

dem japanischen Dentori Law mit einem
„PSE“ or „T”-Symbol markiert sein

 Die Minimalanforderungen für das Kabel

sind .75m ㎡ Leiter.

C. Für andere Länder:

 Die Zubehörteile des Kabel-Sets müssen das

Prüfsiegel derjenigen Stelle, die in dem
jeweiligen Land für die Sicherheitsprüfung
zuständig ist, tragen.

 Das Kabel muss vom HAR (harmonisierten) Typ

H03VV-F sein.

 Das Kabel-Set muss eine Stromkapazität von

mindestens 2,5 Ampere haben und Spannungen
von 125 oder 250 V Wechselstrom gestatten.

18. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die

grundlegenden Sicherheitsmaßnahmen beachten, um das
Risiko von Feuer, Stromschlägen und Verletzungen zu
minimieren. Zu beachten sind u.a. folgende Punkte:

¾ Benutzen Sie das Gerät nicht in der Nähe von Wasser,

wie zum Beispiel Badewanne, Waschbecken,
Spülbecken, Waschbottich, in feuchten Kellerräumen
oder in der Nähe von Schwimmbecken.

¾ Benutzen Sie kein Telefon (ausgenommen schnurlose

Modelle) während eines Gewitters. Es besteht das
geringe Restrisiko eines Blitzschlages.

¾ Benutzen Sie das Telefon nicht um ein Gasleck zu

melden, falls es sich in der Nähe des Lecks befindet.

¾ Benutzen Sie nur solch ein Stromkabel, wie in dieser

Anleitung beschrieben.

19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu

Wasser oder anderen Flüssigkeiten. Gießen Sie nie
Flüssigkeiten über das Netzteil.

20. Achtung Laser: Laser Produkt der Klasse I. Achtung -

Unsichtbarer Laserstrahl, vermeiden Sie Kontakt mit dem
Strahl bei offenem Gehäuse.

21. Es besteht Explosionsgefahr, wenn der Akku nicht

ordnungsgemäß ersetzt wird. Ersetzen Sie den Akku nur
durch einen Akku gleichen oder äquivalenten Typs, der vom
Hersteller empfohlen wird.

8

Entsorgen Sie Akkus entsprechend den Anweisungen des
Herstellers. Entfernen Sie den Akku auf keinen Fall bei
eingeschaltetem Notebook, da hierdurch Daten verloren
gehen könnten.

22. Der Netzeingabeanschluss dient als Hauptschalter des Geräts.

23. Hinweis für die CATV-Systeminstallation: Dieser Hinweis dient

dazu, die Aufmerksamkeit der CATV-Systemmonteure auf
Abschnitt 820-93 des National Electrical Code zu richten, der
Richtlinien für die korrekte Erdung enthält und im Besonderen
festlegt, dass der Schirm des Koaxialkabels an das
Erdungssystem des Gebäudes angeschlossen werden muss,
und zwar so nahe wie möglich am Ort des Kabeleingangs

Things you must remember before working on your
computer

Let your computer acclimate itself

Your notebook can easily stand temperature extremes but it
doesn’t like rapid changes in temperature, like going from the cold
outdoors to a warm office.

Rapid changes in temperature can cause water droplets to
condense inside your case, threatening to damage the electronic
parts inside.

After receiving your notebook when it’s hot or cold outside, try not
to power up the computer immediately, let the computer adjust to
the room temperature gradually at least for three to four hours.

If your system arrives in cold
weather, do not apply power to the computer or monitor until
they have been allowed to come to room temperature.

Heat, Cold, Humidity, and Glare

Find a suitable place for your computer that’s not too hot, too cold,
too dark, or too bright. Glare can make it hard to read the screen.

• Try to avoid the computer components from being destroyed if

it is over heated, so try to allow plenty of room for air to
circulate around the case.

• Do not block the ventilation opening.

• Do not place your computer in direct sunlight.

9

Suitable place to work

Your computer will run well wherever you’re comfortable but
extremes of temperature and humidity can be challenging to your
system’s parts.

There are some things you can tolerate that the computer can’t –
things like static electricity, dust, water, steam and oil. In case you
decide to pull over for roadside computing, try to choose a clean,
comfortable work area for your system.

A lithium-ion battery pack will be available when you are traveling.
If you are running your system for the first time on battery power,
remove the battery from the package, install it into the system and
recharge the battery to fully prepare for service.

10

11

IInnttrroodduuccttiioonn

Welcome to the Notebook PC

Congratulations on your purchase of the Notebook PC. Your
Notebook features the latest advances in portable computing
technology. The Notebook’s modular design provides maximum
expandability without compromising portability.

Getting to Know Your Computer

Opening the LCD Panel

To avoid damage to the display

panel:

1. Try not to slam the display upon closing it.

2. Try not to place any object on top when it is closed or open.

3. Be sure the system is turned off or in suspend mode before
you close the display panel.

With the LCD screen open, you will see several features important
for operating your Notebook computer.

12

Front View

Do not place any heavy objects

on the top of notebook. This may damage the display

1. LCD Latch

2. CCD Camera

3. LCD Display

4.

Music Button

5.

Mute Button

6. Power Button

7. Keyboard

8. Touchpad

9. LED Status Indicator

13

System & Power Status Indicators

LED

Symbol

Indication

Blue light indicates the touchpad is disabled.

Blue light indicates the WLAN module is active.
Persistent Blue light indicates the Suspend Mode is

enabled.
Blinking orange light indicates the battery is being charged.

Blinking red light indicates the battery power is low when
the system is turned ON.
Persistent green light indicates the battery is Full.

Blue light indicates the hard drive and/or optical drive is
being accessed.

Blue light indicates the numeric keypad is activated.

Blue light indicates the cap-lock is activated.

Blue light indicates the scroll-lock is activated.

10. Wireless On/Off Switch.

11. Audio and Power Management Button

¾

Previous Button

¾

Play Button

¾

Advance Button

¾

Stop Button

¾

Power Management Button

¾

Volume Tool Bar

12. Touchpad Button

14

Left View

1. Microphone/Audio Line-in Jack

2. Stereo Headphone/SPDIF-out Jack

3. ExpressCard (New Card) Slot

4. Optical Drive
Right Views

1. 5-in-1 Card Reader (SD/MMC/MS/MS Pro/XD)

2. USB2.0 Port

15

Rear Views

1. Kensington Lock

2. Ventilation Opening

3. External CRT Port

4. S-Video output Port

5. HDMI Port

6. Power Jack (DC-in)

7. 1394 Port

8. Modem Port

Always disconnect all telephone lines
from the wall outlet before servicing or disassembling this
equipment. To reduce the risk of fire use only No. 26 AWG or
larger telecommunication line cord.

9. LAN Port

When using a LAN, please use an EMI
Shielding Cable to minimize an inteference when transmitting.
In order to meet EMV requirements, kindly locate the Core (for
LAN cable) that can be found in the accessory box.

10. USB Port

11. E-SATA Port

16

Bottom View

1. Battery Release Latch

2. Battery Compartment

3. Hard Disk Drive

17

GGeettttiinngg SSttaarrtteedd

Connecting to a Power Source

Connecting the AC Adapter

A universal AC adapter is provided to supply your computer with
power and also charge the computer’s battery pack. The adapter’s
AC input voltage can range anywhere from 100 to 240 volts,
covering the standard voltages available in almost every country.
To connect the computer to an external power source:

Do not use inferior extension
cords as this may result in damage to your Notebook. The
Notebook comes with its own AC adapter. Do not use a
different adapter to power the computer and other electrical
devices.

Whenever possible, keep the AC adapter plugged into the

18

Notebook and an electrical outlet to recharge the battery.

Never turn off or reset your
Notebook while the hard disk is in use and the CD-ROM status
icon is lit; doing so can result in loss or destruction of your
data. Always wait at least 5 seconds after turning off your
Notebook before turning it back on; turning the power on and
off in rapid succession can damage the Notebook’s electrical
circuitry.

Turning On Your Notebook Computer

Turn on your Notebook by pressing the power button. Hold the
button down for a second or two and release. The Power-On Self
Test (POST) runs automatically.

After the POST is completed, the computer reads the operating
system from the hard disk drive into computer memory (this is
commonly referred to as “booting” a computer). If your OS
(Operating System such as Windows Vista…. etc) is installed, it
should start automatically.

To turn the Notebook off, save your work and close all open
applications, click on Start, then Shu

t Down and select Shut

down the computer and click "Yes" or press the power button for

4-6 seconds.

Operating on Battery Power

Your computer comes with a rechargeable battery pack that lets
you operate the computer without an external power source.
When the battery pack is fully charged, you can operate the
computer under the following conditions:

• The battery pack initially has a full charge.

• No peripheral devices are installed.

• The disk/CD-ROM drives run no more than 10% of the time.

Only use batteries that are
approved by an authorized dealer. All batteries are not the
same and therefore should not be treated as such. Using the
wrong battery could cause serious damage to your computer
and yourself through toxic emissions.

19

Danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions or local
laws.

Explisionsgefahr bei unsachgernazen
Austausch der Batterie. Ersatz nur durch denselben oder
einem vom Hersteller empfohlenem ahnlichen Typ.
Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.

Installing and Removing the Battery Pack

To Remove the Battery Pack:

Slide the battery release latch and push the battery away from its
compartment.

To Install the Battery Pack:

Alight the battery into the compartment and push it inside to
completely attach the battery. A click sound will be heard pushing
the latch into lock position.

20

Charging the Battery Pack

The installed battery pack charges automatically any time the
computer is connected to the AC adapter and an external power
source. It is a good idea to occasionally discharge the battery pack
fully to preserve its operating performance.

21

UUssiinngg tthhee NNootteebbooookk CCoommppuutteerr

Adjusting the LCD Screen Display

The LCD screen display can be adjusted by the following key
combinations.

KEYS FUNCTIONS

Fn + F9 Increases the brightness level.
Fn + F8 Decreases the brightness level.
Fn + F10 Changes Display Mode: LCD-only, CRT-only and

LCD&CRT.

LCD Care

LCD screens are delicate devices that need careful handling.
Please pay attention to the following precautions:

• When you are not using the computer, keep the LCD screen

closed to protect it from dust.

• If you need to clean your LCD screen, use a soft tissue to

gently wipe the LCD surface.

• Do not put your fingers or sharp objects directly on the surface

and never spray cleaner directly onto the display.

• Do not press on, or store any objects on the cover when it is

closed. Doing so may cause the LCD to break.

External CRT Display

You can hook up an external monitor through the 15-pin CRT
connector. Three configurations are available:

• LCD only

• CRT only

• Simultaneous display of the LCD screen and CRT monitor

22

You can switch between these display configurations by pressing
the key combination [Fn] + [F10].

For information on connecting an external display, please refer to
Chapter Four.

The Notebook’s Hot Key Controls

Function Keys (Quick Keys)

Action System Control

Fn + F3 Mute the system.
Fn + F4 Turns Speaker Volume down.
Fn + F5 Turns Speaker Volume up.
Fn + F6 Enable/Disable touchpad
Fn + F7 Enable/Disable CCD camera
Fn + F8 Decreases Display Brightness.
Fn + F9 Increases Display Brightness.
Fn + F10 Changes Display Mode: LCD-only, CRT-only and

LCD&CRT.

Fn + F12 Enters Suspend Mode.

The TouchPad

The touchpad is a rectangular electronic panel located just below
your keyboard. You can use the static-sensitive panel of the
touchpad and slit it to move the cursor. You can use the buttons
below the touchpad as left and right mouse buttons.

TouchPad Precautions

The TouchPad is a pressure sensitive device. Please take note of
the following precautions.

• Make sure the TouchPad does not come into contact with dirt,

liquids or grease.

• Do not touch the TouchPad if your fingers are dirty.

• Do not rest heavy objects on the TouchPad or the TouchPad

buttons.

You can use the TouchPad with Microsoft Windows as well as non­Windows applications.

The DVD Dual

Features of the DVD Dual

The features of the DVD Dual are listed below.

23

• The Audio Play feature allows you to play music CDs

• Front panel load/unload button

• Supports CD-DA, CD-ROM mode 1 and mode 2, Multi-Session

Photo CD™, CD-I/Video CD (pcs.)

• Low power consumption

• 12.7mm height

Precautions for Handling CD Discs

• Always hold the disc by the edges, avoid touching the surface.

• Use a clean, dry, cloth to remove dust, smudges, or fingerprints.

Wipe from the center outward.

• Do not write or place objects on the surface of the disc.

• Store discs in a cool dry place not to damage the disc.

• Do not use benzene, thinners, or cleaners with detergent. Only

use CD-ROM/DVD-ROM/Combo cleaning kits.

• Do not bend or drop the discs.

Loading a Disc

To play a CD disc, follow the instructions listed below.

• Push the DVD Dual eject button on the CD drive door. Gently

pull the tray all the way out.

• Carefully lift the CD disc by the edges and make sure the shiny

surface is face down (the side with no writing on it). Carefully
insert the CD disc onto the tray. Push the CD disc down gently
so that it snaps onto the center ring.

• Push the tray back into the drive.

To remove a CD disc, do the following:

• Check the LED display and make sure that the computer is not

accessing the DVD Dual.

• Push the eject button and pull the tray all the way out.

• Carefully pick up the CD disc by the edges and – while

pressing down on the center ring – remove the CD disc from
the tray.

Do not insert any foreign objects into the
disc tray. If you experience difficulty when ejecting the CD
disc tray, stretch a paper clip (or use a pin or a thin metal rod)
and insert it into the emergency eject hole located on the right
side of the front panel.

24

The CD disk tray should eject immediately. This procedure
can also be used to remove a CD from the drive when the
Notebook is powered off.

Power Saving Modes

This section contains information on the Notebook’s power system,
including the AC Adapter, the battery system, recharging the
battery, and tips for conserving battery power.

The power system is comprised of two parts, the AC Adapter and
the battery system. The AC Adapter converts AC power from a wall
outlet to the DC power required by the computer.

The Battery Power System

Before using the computer on battery power for the first time,
check the battery status icon on the Windows Toolbar to make
sure the battery is fully charged.

See Battery Status later in this section for a description and
explanation of the Windows Battery icon.

Charging the battery takes about 3 hours to charge when the
system is in off state. If possible, always charge the battery
completely.

If you use the battery so frequently that it
exceed more than 20 times by fully discharging/charging in a
single month alone, we recommend you to perform the
“Battery Calibration” process every 3 months to maintain the
battery life.
Please refer to the topic on “Battery Calibration” describing
how to calibrate your system battery discussed on the latter
part of this chapter.

If you discover the battery life is getting shorter, please
perform the “Battery Calibration” process immediately.

Removing the Battery Pack

To remove the battery pack from its compartment, please refer to
Chapter 3, Inserting and Removing the Battery Pack.

25

Preparing the Battery Pack for Use (Battery Calibration)

Before using the battery pack for the first time, the Smart Battery
IC within the battery pack should be calibrated in order to get
accurate reporting of remaining battery life status.

To calibrate the battery pack follows the instructions below:

1. Insert the battery into the battery compartment and turn on the

Notebook. If the battery is completely without power go to the
next step. Otherwise, let the battery run down until the battery
low-low warning beeps are heard. The system will
automatically enter Suspend mode.

2. Turn the Notebook off. Connect the AC adapter and let the

battery fully recharge. When the battery charge indicator turns
off, the battery is fully charged.

3. Turn On the notebook, let the battery run down until the

battery is in low-low state and you hear a warning beeps. The
system will automatically enter the Suspend mode. You can
now connect the AC adapter.

4. The battery pack is now calibrated properly.
In general, using the battery until the low-low battery-warning

indicator appears and fully recharges the battery each time (full
discharge/charge cycle) will ensure the accurate reporting of the
battery gauge status.

Automatic Battery Pack Charging Function

To charge the battery, while the battery pack is in the notebook,
plug the AC adapter into the notebook and an electrical outlet.

The charging time is approximately 4-6 hours when the notebook is
turned off and approximately 6-10 hours when the notebook is
turned on.

When the battery is fully charged, the battery charge indicator
becomes green.

If system runs at heavy loading or in a
high temperature environment, the battery may not be fully
charged. You need to continue to charge it with the AC
adapter plugged in until the charging LED turns green.

26

Battery Status

Windows Vista has an applet in the Control Panel that will display
an icon in the Windows taskbar indicating when the Notebook is
running on battery power or is attached to the AC adapter.

This applet also displays a meter that indicates how much charge
is remaining in the battery.

Battery Low Warning

When the pack initially reaches the “Battery Low” state
approximately 7 ~ 10 minutes of the usable battery life is left.

You will hear an audible beep signal every 15 seconds alerting you
to the “Battery Low” status. When the battery power reaches the
“Battery Low Low” status the beeping sound will accelerate.

Your battery now has 1 ~ 2 minutes of battery charge remaining.
You must save your data or connect AC power immediately;
otherwise, you may lose your data.

Sound Meaning

Continuous
beeping every 5
seconds

Battery Low: Indicates that there is 7 to 10 minutes
charge remaining.

Beeping
accelerates

Battery Low Low: Indicates that there is 1 to 2
minutes of battery charge remaining. Save your
work and turn off the Notebook, or connect the AC
adapter.

When there is only one minute of battery charge remaining, the
Notebook will suspend to the HDD and power off. You should
connect AC power and resume to save your work.

Small Battery for the Real Time Clock

There is a small built-in battery pack that supplies power to the
system in order to maintain certain system information while the
power is off.

27

If the Notebook is left without a power source for long period of
time, this battery will be exhausted and system information will be
lost.

Danger of explosion if battery is
incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer's instructions. Never
remove the battery pack while the power is on as this may
result in data loss when the system loses power.

Resetting the System

After installing a software application package, you may be
prompted to reset the system to load the changed operating
environment. To reset the system, or “reboot,” press the
[Ctrl]+[Alt]+[Delete] keys simultaneously.

This is known as “warm boot.” This key combination acts as
“software” reset switch when you encounter hardware or software
problems, which lock up the Notebook.

If this key combination does not shut down the Notebook, you can
reset the Notebook by using the Notebook’s power button. Should
the Notebook lock up for some reason, pressing this button powers
the Notebook off.

Adjusting the Brightness

To adjust the brightness on the LCD screen, press and hold down
the [Fn] key in the lower left hand corner of the keyboard and
press the [F8] key to reduce the brightness or [F9] to increase the
brightness.

28

Using the Windows

Help Windows

For Windows Vista help,
click Start ÎHelp and
Support icon will open
the dialog box.

Desktop

Desktop may vary differently on the software installed in your
notebook with different or additional shortcuts.

29

Recycle Bin

Used for storing deleted files in case you want to recover and save
it in your system. The files will only be deleted from the Recycle
Bin permanently only if you empty it by right clicking your mouse
and select the “Empty Recycle Bin”.

Start Button

Allows easy access to all Windows programs.

The Start menu allows you to adapt and show the programs used
most frequently. If you wish to keep an item, right click the item and
click Pin to Start menu.

Log Off will enable the current user to log off and allows a new
user to log on.

Turn Off Computer allows you to shut down, restart, and Stand by
modes for power saving purposes.

Taskbar

When you open a program, its icon is displayed at the taskbar for
you to conveniently move between programs by clicking the
relevant button.

To add or remove toolbars from the taskbar: right click an empty
spot on the taskbar, select Toolbars Î choose the toolbar you
want to a dd.

30

Notification

The icons that appear here are for quick access to some programs
and computer functions that you frequently used. For you to see
the hidden icons, simply click the

icon.

To prevent Windows Vista from hiding icons:
From an empty spot on the Taskbar, right click your mouse and

select the Properties, remove the checked mark on the Hide
inactive icons.

31

Control Panel

It is in this area that you can change how Windows looks and
works. Click Start Î Control Panel dialog box. There are two
interfaces – Classic View.

32

33

DDeesskkttoopp OOppeerraattiioonn

Your notebook is capable of providing you with efficient and
productive mobile computing, it also has the speed and capacity to
service as a desktop system.

This chapter discusses those functions of your notebook that are
typical of desktop systems.

Audio

The Multimedia Sound System

The Notebook’s built-in audio capabilities allow you to take
advantage of a wide range of education and entertainment
multimedia software. The Notebook is equipped with two internal
stereo speakers, a microphone, and input audio ports for external
audio units.

An external microphone can be connected to the microphone jack.
External speakers or headphones can be connected to the
Notebook’s audio-out jack.

External audio devices can be connected to the Line in jack. All
audio features are software controlled. The Notebook’s multimedia
sound system includes the following features:

• Supports Windows Sound System compatibility

• Full Duplex operation

• Dynamic filtering reduces noise and distortion rate

• 16-bit digitized audio playback

• Built-in stereo speakers

• Digitized audio recording through the Notebook’s built-in

microphone or any external source

34

Audio Volume Control

The Notebook is equipped with hot-key volume controls: Pressing
the [Fn]+[F4] hot-key combination decreases the audio output
volume, press the [Fn]+[F5] hot-key combination increases the
audio output volume.

Audio Software

Your notebook comes equipped with an integrated sound system
capable of providing you with quality audio sound through the built­in speakers or through external speakers connected via the system
ports.

Sound Recording

Your system allows you to record sounds and store them as files
using the microphone via the microphone jack on the rear of the
notebook computer. Check the Windows Help and Support Center
in Windows for information on using the various elements in sound
recording.

For a high-quality sound, click on the
"Volume Control" at the lower right end of your screen. From
the Volume Control windows, click on the "Advanced" tab,
click and select the "Microphone Boost" item.

Playing Sound Files

Your notebook can play audio files stored in MIDI, WAVE or MP3
file format. Check the Help and Support Center in Windows for
information on the functions of the Media Player.

External Speakers and Microphone

The sound system is capable in providing high-quality sound to
external speakers and receiving and processing sounds from an
external microphone or external sound source.

Connecting Peripheral Devices

To expand your computing capabilities, you can add a variety of
external devices to your computer.

35

IInntteerrnneett CCoonnnneeccttiioonn

There are numerous ways to connect to the Internet. This may vary
from the user’s working environment as well as system
specifications.

• Using a modem and a telephone line (Optional)

• Using a wired LAN

• Using a wireless LAN

Using a modem for Connection to Internet (Optional)

• Use a telephone line to connect to the modem port of your

computer. Do not use a digital telephone line.

• Please apply to an Internet Service Provider (ISP) for Internet

service in order for you to connect the modem to the Internet
and use e-mail.

For more detail on the Network key,
please refer to your local ISP provider and follow the
procedures describe in the “ISP Installation Guide” to
proceed with the installation.

36

Using a wired LAN for Connection to Internet

For you connect to the Internet, a wired LAN environment normally
uses the company’s LAN or a broadband modem.

37

Using Wireless LAN Network for Connection to Internet

Bluetooth Connection (Optional)

Bluetooth is a developing, world wide, open, short-range radio
specification focused on communication between the Internet and
Net devices, plus it defines communication protocols between
devices and computers.

It connect wirelessly to your world: In home, at work, in motion and
at play.

Access the internet or your e-mail account from anywhere, anytime.
Fast downloads.

Press on the Bluetooth icon to connect other devices that have

this application.

38

This will be the display that will appear on your screen.
If the system detects any other devices, it will be shown this way:

39

RRuunnnniinngg BBIIOOSS SSeettuupp

The Setup Utility is a hardware configuration program built into
your computer’s BIOS (Basic Input/Output System). It runs and
maintains a variety of hardware functions. It is menu-driven
software, which allows you to easily configure and change the
settings.

The BIOS contains manufacture’s default settings for the
computer’s standard operations. However, there are occasions
when you may be required to modify the default settings in the
BIOS.

The BIOS allows you to set up passwords to limit access to users.
This is an important feature because a great deal of vital
information is carried within the computer nowadays. Unauthorized
access can be prevented. Later in this chapter, you will learn how
to use this security feature.

Entering the BIOS Setup Screen

First turn on the power. When the BIOS performs the POST
(Power-On Self Test), press F2 key quickly to activate the AMI
BIOS Setup Utility.

You may need to press F2 key fairly
quickly. Once the system begins to load Windows, you may
have to retry by cycle-power on again

Leaving the BIOS Setup Screen

When you have finished modifying the BIOS settings, exit the
BIOS. It takes a few seconds to record changes in the CMOS.

40

BIOS Action Keys

Function

Key

Command Description

ESC Exit

Leaves a sub-menu to return to the
previous menu OR exits the BIOS setup

while saving changes.
Enter Go to Sub Screen Shows the Sub Menu
F1 General Help Shows the Help Screen
F9 Setup Default Load default configuration
F10 Save and Exit Saves changes and reboots the computer.
<Tab> Select a field Selects the next field.
Ï

Select an item Selects the next upper item.

Ð

Select an item Selects the next lower item.

Î

Select Menu Select the next Menu.

Í

Select Menu Select the previous Menu.

- Lower value Selects the next value within a field.
+ Higher value Selects the next value within a field.

Modifying the BIOS Settings

The BIOS setup main menu is subdivided into sub-menus. Each
menu item is described in this section.

Info

Main info of the manufacturer.

41

Main Setup

Under this menu, you may change time/date and view basic
processor and system memory information.

Advanced Setup

42

Security

Power

43

Boot Setup

Exit Setup

44

45

VVGGAA UUttiilliittiieess

You can also click the touchpad or mouse right button and select
the “ATI CATALYST® Control Center” item.

46

Display Manager

This feature allows you to connect external display devices.

47

Display Options

48

Notebook Panel Properties

49

Color

50

Video

51

52

PowerPlay

53

VViiddeeoo CCoonnffeerreenncciinngg ((OOppttiioonnaall))

This application offers video conferencing capabilities to work and
communicate in real-time with one or more participants through
streaming video, from any location.

Web Camera Application

Press the “Camera” icon or “Fn + F7” key to display the
“Web Camera” screen display. Your image will immediately display
on the small screen.

After a video appear on the “Camera Assistant Software Lite”
application window, press on the “Capture” button to capture the
picture.

54

Using Commands and Buttons

Snapshot Command

Click on the “Snapshot” button to capture the present
picture that appear in the “Camera Assistant Software Lite”
window.

Record Command

Click on the “Record” button to capture the video played in
the “Camera Assistant Software Lite” window.

55

Property Command

Press on the “Property” icon to display the “Property”
settings window.

This dialog box has the following scroll bars and buttons for
controlling the color components of the video image.

56

Setting Command

Press on the “Setting” icon to display the “Property”
properties window.

This dialog box has the following scroll bars for selecting the
default video format, color space, output size.

57

TTrroouubblleesshhoooottiinngg

Your computer has been fully tested and complies with the system
specifications before shipping. However, incorrect operations
and/or mishandling may cause problems.

This chapter provides a reference for identifying and correcting
common hardware and software problems that you may encounter.

When you encounter a problem, you should first try to go through
the recommendations in this chapter. Instead of returning the
computer and waiting for repair, you may easily solve the problems
by considering the following scenarios and possible solutions. If
the error continues, contact your reseller for service information.

Before taking further actions, consider the following suggestions:

• Check to see if the problem persists when all the external

devices are removed.

• Check to see that the green light indicator on the AC adapter is

lit.

• Check to see the power cord is properly plugged to the wall

outlet and to the computer.

• Check to see the power indicator of the computer is on.

• Check to see if your keyboard is operational by pressing and

holding any key.

• Check for any incorrect or loose cable connections. Make sure

the latches on the connectors latch securely on to the receptor
end.

• Be sure you have not performed an incorrect setting on the

hardware devices in the BIOS Setup utility. A faulty setting may
cause the system to misbehave. If you are not sure of the
changes you made, try to restore all the settings to factory
defaults.

58

• Be sure all the device drivers are installed properly. For

example, without the audio driver properly installed, the
speakers and microphone will not work.

• If external devices such as USB camera, scanner, printer do

not function correctly when connected to the system, it is
usually the device’s own problem. Consult the device’s
manufacturer first.

• Some software programs, which have not gone through

rigorous coding and testing, may cause problems during your
routine use. Consult the software vendor for problem solving.

• Legacy peripheral are not plug-and-play capable. You need to

restart the system with these devices powered up and
connected first.

• Be sure to go to BIOS SETUP and load DEFAULT SETTING

after BIOS re-flash.

• Be sure the Quick Key Lockout Switch on the bottom of the

computer is not engaged; otherwise the quick keys will not
work.

Audio Problems

No speaker output -

• Software volume control is turned down in Microsoft Sound

System or is muted. Double-click the speaker icon on the lower
right corner of the taskbar to see if the speaker has been
muted or turned down all the way.

• Most audio problems are software-related. If your computer

worked before, chances are software may have been set
incorrectly.

• Go to [Start > Settings > Control Panel] and double-click the

Sounds and Audio Devices icon. In the Audio page, make sure
that Realtek AC97 Audio is the default playback device.

Sound cannot be recorded -

• You will need to plug-in an external microphone to the

microphone connector to record sound.

• Double-click the speaker icon on the lower right corner of the

taskbar to see if the microphone has been muted.

¾ Click Options and select Properties.
¾ Select Recording and click the OK button.

59

¾ After Click OK button, the recording volume control

panel will appear.

• Go to [Start > Settings > Control Panel] and double-click the

Multimedia icon (or Sounds and Audio Devices icon). In the
Volume or Audio page, make sure that Realtek AC97 Audio is
the default recording device.

Hard Disk Problems

The hard disk drive does not work or is not recognizable

• If you had just performed a hard disk upgrade, make sure the

hard drive connector is not loose and the hard disk drive is also
correctly seated. Remove it and reinsert it firmly, and restart
your PC. (Refer to Chapter 4 for details.)

• The new HDD may need to be partitioned and reformatted. O/S

and drivers will need to be re-installed as well.

• Check the hard disk indicator LED. When you access a file, the

LED lamp should light up momentarily.

• The new HDD may be defective or is not compatible.

• If your computer has been subjected to static electricity or

physical shock, you may have damaged the disk drive.

The hard drive is making abnormal whining noises

• You should back up your files as soon as possible.

• Make sure the source of noise is indeed from the hard drive

and not the fan or other devices.

The hard disk drive has reached its capacity

• Run Disk Cleanup utility in Windows. [Start > All Programs >

Accessories > System Tools > Disk Cleanup] The system will
prompt you for what to do.

• Archive files or programs that you had no longer used by

moving them to an alternative storage medium (floppy disk,
optical record-able disk, etc.) or uninstall programs that no
longer use.

• Many browsers store files in the hard drive as a cache to speed

up the performance. Check the program’s Online Help for
instructions on decreasing the cache size or on removing
temporary Internet files.

• Empty the Recycle Bin to create more disk space. When you

delete files, Windows saves them to the Recycle Bin.

60

The hard disk takes longer to read a file

• If you have been using the drive for a period, the files may be

fragmented. Go to [Start > Programs > Accessories > System
Tools > Disk Defragmenter] to perform a disk defragmentation.
This operation may take a while.

• Interrupt requests or problems with other hardware devices

may have occupied the CPU and therefore slows down the
system performance.

The files are corrupted

• Run the Error-checking utility in Windows to check the HDD.

Double-click My Computer. Right-click C: and select Properties.
Click Check Now in Error-checking in Tools.

Optical Drive Problems

The optical drive does not work

• Try rebooting the system.

• The disk is damaged or files are not readable.

• After you have inserted a CD-ROM disk, it may take a moment

before you can access its content.

The drive dose not read any disks

• The CD may not be properly seated in the tray. Make sure the

disk is firmly seated onto the spindle.

• The disk is damaged or not readable.

The disk cannot be ejected

• Normally, it takes a few seconds to eject the disk.

• If the disk cannot be ejected, it may be mechanically jammed.

Straighten out a paper clip and insert it to a tiny hole next to the
eject button. This should reject the disk tray. If not, return the
unit for repair. Do not forcefully pull on the disk tray.

The Combo or DVD RW drive cannot record

• You need to purchase and install a burner utility program to

record files to a blank media.

61

Display Problems

The display panel is blank when the system is turned on

• Make sure the computer is not in the Standby or Hibernate

suspend modes. The display is turned off to conserve energy in
these modes.

The screen is difficult to read -

• The display resolution should at least be set to at

least1024x768 for optimal viewing.

¾ Go to [Start > Settings > Control Panel] and double-click

the Display icon.

¾ Under the Settings page, set screen resolution to at

least 1024x800 and choose at least 256 colors.

The screen flickers -

• It is normal if the display flickers a few times during shutting

down or powering up.

Keyboard and Mouse Problems

The built-in touch pad performs erratically -

• Make sure there is no excess perspiration or humidity on your

hand when using the touch pad. Keep the surface of the touch
pad clean and dry.

• Do not rest your palm or wrist on the surface of the touch pad

while typing or using the touch pad.

The built-in keyboard accepts no input -

• If you are connecting an external keyboard to the system, the

built-in keyboard may not work.

• Try restarting the system.

The characters on the screen repeat while I type.

• You may be holding the keys down too long while you’re typing.

• Keep the keyboard clean. Dust and dirt under the keys could

cause them to stick.

• Configure the keyboard to wait longer before the auto repeat

feature starts. To adjust this feature, Go to [Start > Settings >
Control Panel], and double-click the Keyboard icon. A dialogue

62

box shows up with the adjustable settings for the keyboard.

CMOS Battery Problem

A message “CMOS Checksum Failure” displays during the
booting process or the time (clock) resets when booting

• Try to reboot the system.

• If the message “CMOS Checksum Failure” appears during the

booting procedure even after rebooting, it may indicate failure
of the CMOS battery. If so, you need to replace the battery.
This battery normally lasts two to five years. The battery is of
type CR2032 (3V). You may replace it by yourself. The battery
is located under the System Device Cover on the bottom of the
notebook. See Chapter 4 for more details.

Memory Problems

The POST does not show an increased memory capacity
when you have already installed additional memory

• Certain brands of memory module may not be compatible with

your system. You should ask your vendor for a list of
compatible DIMM.

• The memory module may not be installed properly. Go back to

Chapter 4 to review the details of this operation.

• The memory module may be defective.

The O/S issues an insufficient memory error message during
operation

• This is often a software or Windows-related problem. A

program is draining the memory resources.

• Close the application programs you’re not using and restart the

system.

• You need to install additional memory module. For instructions,

go to Chapter 4 Upgrading Your Computer.

PC Card / PCMCIA Problems

Some system may not have the PC Card

Slot option.

PC Cards do not function-

• Make sure you have properly installed the driver for the card.

63

• Consult the card’s manual or contact the vendor for trouble-

shooting.

The PC card cannot be recognized -

• Windows NT4.0 does not support PCMCIA (PC Card) function.

You may need an external program for this.

• Make sure the card is fully inserted; the outer end of the card

should be even with the edge of the computer.

• Remove and insert the PC card again.

• Make sure there is no IRQ conflict with the card. See Windows

on-line help for solving IRQ conflicts.

• Reboot the computer and see if the problem persists.

• The card may be defective. Try the card on another system, if

possible.

Windows crashes or freezes when you remove the PC card-

• Make sure you have <Stop> the PC card before removing it.

Double-click the Safely Remove Hardware icon at the lower
right corner of the task bar and select the card you wish to stop.
When you click <Close>, in few seconds Windows will prompt
you to remove the card.

Performance Problems

The computer becomes hot -

• In a 35oC environment, the certain areas of the computer’s

back case are expected to reach 50 degrees.

• Make sure the air vents are not blocked.

• If the fan does not seem to be working at high temperature (50

degrees Celsius and up), contact the service center.

• Certain programs that are processor-intensive may increase

the computer temperature to a degree where the computer
automatically slows down its CPU clock to protect itself from
thermal damage.

The program appears stopped or runs very slowly -

• Press CTRL+ALT+DEL to see if an application is still

responding.

• Restart the computer.

• This may be normal for Windows when it is processing other

CPU-intensive programs in the background or when the

64

system is accessing slow-speed devices such the floppy disk
drive.

• You may be running too many applications. Try to close some

applications or increase system memory for higher
performance.

• The processor may have been overheated due to the system’s

inability to regulate its internal heat. Make sure the computer’s
ventilation grills are not blocked.

USB2.0 Problems

The USB device does not work -

• Windows NT 4.0 does not support USB protocols

• Check the settings in the Windows Control Panel.

• Make sure you have installed the necessary device drivers.

• Contact the device vendor for additional support.

65

SSppeecciiffiiccaattiioonn

Ｏperating System

• Supports Windows Vista Premium

• Linux Knoppix bootable

CPU

• Merom For Santa Rosa dual core processor, T7800, FSB 800

MHz, L2 cache 4MB, TDP 35W

• Celeron M / TJ85 CPU

Memory

• Supports dual channels DDR2 memory interface.

• Supports DDRII 533/667 SO-DIMM module per channel

Core Logic

• Crestline PM965 + ICH8M

VGA

• ATI M76 XT

Audio Codec

• Realtek_ALC883

Express Card

• Support New card type II

• Support both 34/54mm

• PCI-E interface

66

IEEE 1394

• Support IEEE 1394 and 1394a with Open HCI Compliance

• PCI V2.2 MAC/BIU supports

TV-Encoder

• Display on a PAL or NTSC TV

• Support for Macrovision 7.1 copy protection standard-a fully

programmable timing capability

LAN Controller

• Giga LAN

• PCI-E interface

Modem

• 56K MDC Modem card with Azalia standard support

• MDC 1.5 interface

Wireless LAN

• Mini-Card type

• PCI-E interface

• IEEE 802.11a/b/g, Wi-Fi compliant

• 3 Antenna supported

Keyboard

• 88 Keys K/B, KBD Dimension: 305mm

• Vista logo keyboard

Pointing Device

• Synaptics TM61PDZG300

LCD

• 15.4” WXGA, resolution 1280 x 800

• WXGA+, resolution 1440 x 900

• WSXGA+, resolution 1680X1050

• Glare/Non Wide view type

HDD

• 1 x 2.5” (9.5mm) HDD

• Support SATA 2.0 HDD

67

Optical Device

• DVD Dual (Double Layer) and BluRay and HD DVD support

• GBAS support

• Support PATA interface only

Card reader Controller

• Support SD/MMC/MS/MS Pro/XD Memory Card

• USB 2.0 Single interface

Battery Pack

• 8 Cells Battery Pack Support

AC-Adapter

• Automatics Voltage adjustment between 100 and 240VAC

50/60Hz 120 Watts (3pin)

Speaker/MIC

• Built-in 2 speakers

• Speaker: 2W and 4 ohm

• Internal Microphone support, with Microphone array support (2

MIC build in)

BIOS

• Support PnP, APM 1.2 & ACPI 3.0

• Support external USB flash memory card boot up.

• Phoenix trusted core BIOS support

Power Management

• “Smart Power II” Power Management

¾ Proprietary Technology of Battery Life and System

performance Extension

¾ The technology is including Long battery life mode,

Silent mode.

Physical Outline

• Dimension: 360mmX272mmX24~ 37.2mm (w/battery)

• Weight: 3.0Kg

Certification

• EMI: CE report, FCC, CCC

• RF: CE (EN 301 489-1 & 17, EN 300328-2), R&TTE report

68

• Telcom: CTR21 report

• Safery: CB report, UL