Gericom M510C User Manual

I

M510C Notebook PCM510C Notebook PC

M510C Notebook PCM510C Notebook PC

M510C Notebook PC

User’s GuideUser’s Guide

User’s GuideUser’s Guide

User’s Guide

G52-B1003X2

II

Regulations Information

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

z Reorient or relocate the receiving antenna.

z Increase the separation between the equipment and receiver.

z Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

z Consult the dealer or an experienced radio/TV technician for help.

Note

1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

2. Shield interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference
that may cause undesired operation.

III

Safety Guideline for Using Lithium Battery

(Danish) ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig
håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.

(Deutsch) VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch
der Batterie. Ersatz nur durch denselben oder einen vom Hersteller
empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.

(English) CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the equip­ment manufacturer. Discard used batteries according to manufacturer’s
instructions.

(Finnish) VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden mukaisesti.

(French) ATTENTION: II y a danger d’explosion s’il y a remplacement in­correct de la batterie. Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le constructeur. Mettre au
rebut les batteries usagées conformément aux instructions du fabricant.

(Norwegian) ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende type anbefalt av
apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens
instruksjoner.

(Swedish) VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma
batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.

IV

Caution on Using Modem

1. Never install telephone wiring during a lightning storm.

2. Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.

3. Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.

4. Use caution when installing or modifying telephone lines.

5. Avoid using the telephone function (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from lightning.

6. Do not use the telephone function to report a gas leak in the vicinity of the
leak.

CD-ROM Drive Notice

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1

LASER PRODUCT.” To use this model properly, read the instruction manual carefully
and keep this manual for your future reference. In case of any trouble with this model,
please contact your nearest “AUTHORIZED service station.” To prevent direct
exposure to the laser beam, do not try to open the enclosure.

V

Safety Instructions

1. Read the safety instructions carefully and thoroughly.

2. Save this User’s Guide for possible use later.

3. Keep this equipment away from humidity and high temperature.

4. Lay this equipment on a stable surface before setting it up.

5. The openings on the enclosure are used for air convection and to prevent the
equipment from overheating. Do not cover the openings.

6. Make sure that the power voltage is within its safety range and has been
adjusted properly to the value of 100~240V before connecting the equipment
to the power inlet.

7. Place the power cord in a way that people are unlikely to step on it. Do not
place anything on the power cord.

8. Always unplug the power cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage the equipment or
cause an electrical shock.

11. If any of the following situations arises, get the equipment checked by a
service personnel:

z the power cord or plug is damaged.
z liquid has penetrated into the equipment.
z the equipment has been exposed to moisture.
z the equipment has not work well or you can not get it work according to

User’s Guide.

z the equipment was dropped and damaged.
z the equipment has obvious signs of breakage.

12. Do not leave the equipment in an unconditioned environment with a storage
temperature of 60OC (140OF) or above, which may damage the equipment.

13. To prevent explosion caused by improper battery replacement, use the same or
equivalent type of battery recommended by the manufacturer only.

VI

Notice

Please note that the setting diagrams or values in this guide are FOR YOUR REFER­ENCE ONLY. The model you bought may be slightly different from the illustrations

and descriptions in this guide. If you are not sure about these information, such as the
computer’s specification and equipment, please ask your local vendor for help.

Trademarks

* All trademarks are the properties of their respective owners.

* Microsoft is a registered trademark of Microsoft Corporation. Windows® 98/ME
2000/XP are registered trademarks of Microsoft Corporation.

* AMI® is a registered trademark of American Megatrends Inc.

* PCMCIA and CardBus are registered trademarks of the Personal Computer
Memory Card International Association.

Release History

Version Revision Note Date

2.0 First release February 2004

VII

Getting Started

Basics of Using Notebook PC

Table of Contents

1.1 Before You Begin .................................................................1-2

zz

zz

z Unpacking ..............................................................................1-2

zz

zz

z Features and Benefits ............................................................1-3

1.2 Quick Components Guide .................................................. 1-4

zz

zz

z Top-open View.......................................................................1-4

zz

zz

z Right-side View .....................................................................1-6

zz

zz

z Left-side View .......................................................................1-7

zz

zz

z Rear View .............................................................................. 1-8

zz

zz

z Bottom View .......................................................................... 1-10

1.3 Preparing to Operate ..........................................................1-12

zz

zz

z Connecting the Power ...........................................................1-12

zz

zz

z Turning On/Off the Notebook PC .........................................1-14

2.1 Safety and Comfort Tips .....................................................2-2

zz

zz

z Set Up Your Work Environment ............................................2-2

zz

zz

z Have a Good Work Habit ......................................................2-3

2.2 Knowing the Keyboard ....................................................... 2-4

zz

zz

z Typewriter Keys .................................................................... 2-5

zz

zz

z Cursor Keys ........................................................................... 2-6

zz

zz

z Numeric Keys ........................................................................ 2-7

zz

zz

z Function Keys ........................................................................2-8

2.3 Quick Launch Buttons ........................................................ 2-9

VIII

2.4 Knowing the Touchpad ....................................................... 2-11

zz

zz

z Using the Touchpad ............................................................... 2-12

zz

zz

z Configuring the Touchpad ......................................................2-14

2.5 The Hard Disk Drive ..........................................................2-15

2.6 Using the Optical Storage Device .....................................2-16

zz

zz

z Inserting the CD ....................................................................2-17

zz

zz

z Removing the CD .................................................................. 2-18

zz

zz

z Releasing the CD Manually ...................................................2-19

2.7 Using the Video Function ................................................... 2-20

zz

zz

z Powerful Video Controller .....................................................2-20

zz

zz

z Display Modes .......................................................................2-21

zz

zz

z Configuring the Display Settings ............................................2-22

2.8 Using the Audio Function ...................................................2-24

zz

zz

z Connecting Audio Devices ..................................................... 2-24

zz

zz

z Volume Control ...................................................................... 2-25

Using the Software Applications

3.1 Using the Driver CD ........................................................... 3-2

zz

zz

z When do I Need the Driver CD? .......................................... 3-2

zz

zz

z How to Use the Driver CD? ................................................. 3-2

3.2 Advanced Features ..............................................................3-4

zz

zz

z Search Key ............................................................................3-4

Power Management

4.1 Introduction to the Power Source ..................................... 4-2

zz

zz

z The AC Adapter ....................................................................4-2

IX

zz

zz

z The Battery Pack ..................................................................4-3

4.2 Managing the Power ...........................................................4-7

zz

zz

z Power Options .......................................................................4-7

zz

zz

z Intel® SpeedStep

TM

Technology ............................................4-11

BIOS Setup

5.1 Using BIOS Setup Utility.................................................... 5-2

zz

zz

z When to Use BIOS Setup? ...................................................5-2

zz

zz

z How to Run BIOS Setup? .....................................................5-2

zz

zz

z Control Keys .......................................................................... 5-3

5.2 Main Menu ...........................................................................5-4

5.3 Advanced Menu ...................................................................5-6

5.4 Security Menu ......................................................................5-8

5.5 Peripheral Menu .................................................................. 5-11

5.6 Boot Menu ............................................................................ 5-12

5.7 Exit Menu ............................................................................. 5-14

6.1 Connecting the External Devices .....................................6-2

zz

zz

z Connecting the Peripheral Devices .......................................6-2

zz

zz

z Connecting the Communication Devices ...............................6-5

zz

zz

z Installing the PC Card ............................................................6-7

6.2 Safely Remove Hardware ...................................................6-9

6.3 Upgrading Your System ....................................................... 6-10

Expanding and Upgrading

X

Caring Your Notebook PC

7.1 Protecting Your Notebook PC ...........................................7-2

zz

zz

z Locking Your Computer .........................................................7-2

zz

zz

z Setting Up Password ............................................................. 7-3

zz

zz

z Using the Anti-Virus Protection .............................................7-4

7.2 Tips for Traveling ................................................................7-5

7.3 Taking Care of Your Computer ..........................................7-6

zz

zz

z Placing and Operating Your Computer .................................. 7-6

zz

zz

z Cleaning Your Computer ........................................................7-7

zz

zz

z Using the Battery Pack .........................................................7-7

2 - 1

Congratulations on purchasing your M510C Notebook PC!

This chapter first provides a general introduction on your

Notebook PC, to let you know the hardware components

well and start to work easily. Why wait? Read on to learn

more about the powerful features and multimedia function

of your Notebook PC.

Getting Started

1 - 2

M510C Series Notebook PC

1.1 Before You Begin

First, unpack the shipping carton and check all items carefully. If any item
contained is damaged or missing, please contact your local dealer immediately.
Also, keep the box and packing materials in case you need to ship the unit in
the future.

The package should contain the following items:

One M510C Notebook PC.

One Software CD containing the drivers and utilities.

One User’s Manual and one Quick Guide.

One Warranty Card.

Accessories:

- High-capacity Li-ion battery pack.

- AC adapter and power cord.

- Phone cable/Phone jack (optional).

- Notebook PC carry bag (optional).

Unpacking

1 - 3

Features and Benefits

Next Generation CPU Support. Your Notebook PC is equipped with one of

the latest CPU (central processing unit) that supports Intel® Centrino™
technology for excellent system performance and ultimate mobile function.

Integrated Wireless LAN Solution. The computer is pre-installed with the
Intel PRO/Wireless networking solution that allows you to roam between
different rooms in the office or at home, without being disconnected the
LAN cable. In addition, sharing files and printers can be easy tasks.

USB 2.0 Support. The computer has three USB 2.0 ports that support data
transfer rate up to 480Mb/s. The USB standard allows you to connect up to
127 devices through the single interface, including mouse, keyboard, printer,
hard disk drive, digital camera, and more.

IEEE 1394 Support. IEEE 1394 is a high-speed bus that allows you to
connect up to 63 high-end devices on a single computer.

Memory. The computer provides two memory slots that allows you to
expand the memory size up to 2GB.

Integrated 4-in-1 Card Reader. The integrated 4-in-1 card reader supports
MMC (multi-media card), SD (secure digital), SM (smart media), and MS
(memory stick) cards. Without additional cost of purchasing an external
card reader.

Ultimate Graphic System. The integrated ATI Mobility Radeon-M10P Video
controller with 64MB DDR SDRAM empowers your Notebook PC to become
a multimedia center at home, displaying the vivid and rich-color images.

1 - 4

M510C Series Notebook PC

Top-open View

This section provides the multi-views of your Notebook PC, and briefly
introduces the function of each component.

Press the Cover Button to open the top cover (see page 1-6), and you can find
the main operating area of your computer.

1.2 Quick Components Guide

1 - 5

Display Panel

The 15-inch XGA/SXGA+/14.1-inch XGA TFT color LCD screen displays the output
of the computer.

Quick Launch Buttons and Power Button

- Power Button: to turn the computer power ON and OFF.

- Quick Launch Buttons: one-touch buttons, allowing you to launch
specific software application easily (see Quick Launch Buttons in Chapter
2 for more information).

Status LEDs

- Num Lock: glows Green to indicate the Num Lock function is activated.

- Caps Lock: glows Green to indicate the Caps Lock function is activated.

- Scroll Lock: glows Green to indicate the Scroll Lock function is activated.

- Hard Disk In-use: blinks Green to indicate the computer is accessing the
hard disk drive.

Keyboard

The built-in keyboard provides all the functions of a full-sized 87/88-key keyboard
(see Using Keyboard in Chapter 2 for more information).

Touchpad

The pointing device of the computer (see Using Touchpad in Chapter 2 for more
information).

Stereo Speakers

The next-generation high quality speakers send out the sound and voice from the
computer.

Cover Latch

This Cover Latch is used to lock the top cover.

1 - 6

M510C Series Notebook PC

Right-side View

Cover Button

Press this button to open the top cover.

System LEDs

- Wireless LAN: glows Green to indicate the wireless LAN function
of the computer is enabled.

- Power On/Off/Suspend: glows Green to indicate the computer is
turned on; blinks Green to indicate the system is in suspend mode.

- Battery Status: glows Green to indicate the battery is being charged
(with AC adapter connected); glows Orange to indicate low battery
power (less than 5%); blinks Orange to indicate the battery failed.

USB Port

The USB 2.0 port allows you to connect USB-interface peripheral devices,
such as the mouse, keyboard, modem, external hard disk module, printer, and
more.

Ventilator

The ventilator is designed to cool the system. Do not block the ventilator for
air circulation.

Knowing the components on the right side of your computer.

1 - 7

Left-side View

4-in-1 Card Reader

The built-in card reader supports MMC (multi-media card), SD (secure digital),
SM (smart media), and MS (memory stick) cards.

PC Card Slot

The computer provides a PC card slot to support one Type-II PC card for
expansion functions, such as LAN/WLAN card, modem card, memory card,
etc.

Optical Storage Device

A slim CD-ROM/DVD-ROM/CD-RW/DVD Combo/DVD Dual drive is available
in the computer, depending on the model you purchased. The optical device
allows you to use the CD/DVD disc for installing software, accessing data, and
playing music/movie on the computer.

Knowing the components on the left side of your computer.

1 - 8

M510C Series Notebook PC

Rear View

Kensington Lock

This port is used to lock the computer to a location for security (see Caring
Your Notebook PC in Chapter 7 for more information).

Ventilator

The ventilator is designed to cool the system. DO NOT block the ventilator for
air circulation.

Power Connector

To connect the AC adapter and supply power for the computer.

S-Video Connector

By using a Super VHS (S-Video) cable, this connector allows you to connect a
television (NTSC/PAL system) for a great view of the computer display.

VGA Port

The 15-pin D-sub VGA port allows you to connect an external monitor or other
standard VGA-compatible device (such as a projector) for a great view of the
computer display.

Your Notebook PC provides many I/O ports on the rear panel.

1 - 9

Parallel Port

The 25-pin D-sub parallel port allows you to connect a parallel device, such as the
printer and scanner.

USB Ports

The USB 2.0 ports allow you to connect USB-interface peripheral devices, such as the
mouse, keyboard, modem, external hard disk module, printer, and more.

IEEE 1394 Port

The IEEE 1394 port is a high-speed bus that allows you to connect high-end digital
devices such as the DV (digital video camera).

RJ-45 Connector

The 100/10 Ethernet connector is used to connect a LAN cable for network connection.

RJ-11 Connector

The computer provides a built-in modem that allows you to connect an RJ-11 telephone
line through this connector. With the 56K V.90 modem, you can make a dial-up
connection.

Microphone Jack

This connector is used to connect an external microphone.

Audio-out Jack

This connector is used to connect a headphone or external speakers.

1 - 10

M510C Series Notebook PC

Bottom View

Carefully put the computer upside down, and you can find the core components
of the computer.

1 - 11

Battery Unlock Button

If you want to replace a battery, press and slide the button to remove the battery pack.

Battery Pack

To supply power to your computer when the AC adapter is not connected (see
Introduction to the Power Source in Chapter 4 for more information).

Memory Compartment

The computer provides two SO-DIMM slots for expanding the memory size up to 2GB.
Please note that the memory installation/replacement must be done by an authorized
retailer.

Hard Disk Drive Compartment

This compartment contains a holder to secure the hard disk drive of the computer.
Please note that the hard disk drive installation/replacement must be done by an
authorized retailer.

Mini PCI Compartment

The computer provides a built-in wireless LAN card that is installed in this compartment.

CPU Compartment

Inside this compartment is the CPU (central processing unit) and thermal module of
the computer.

1 - 12

M510C Series Notebook PC

Connecting the Power

Your Notebook PC is equipped with a high-capacity 8-cell Li-ion battery pack,
and it can operate either on the battery’s power or AC power. However, for the
first time to use your Notebook PC, it is recommended to connect the AC
adapter and use the AC power. When the AC adapter is connected, the battery
is charged immediately.

Connecting the AC Power

1. Unpack the package to find the AC adapter and power cord.

2. Attach the power cord to the connector of the AC adapter ().

3. Plug the DC end of the adapter to the computer (), and the male end

of the power cord to the electrical outlet ().

4. When the AC adapter is connected, the green LED on the AC adapter

will light up () to indicate that the computer is powered from the
electrical outlet.

Connecting the AC power

1.3 Preparing to Operate

1 - 13

Disconnecting the AC Power

When you disconnect the AC adapter, you should unplug the power cord from
the electrical outlet first, and then unplug the connector from the computer.

Remind you...

1. The AC adapter included in the package is correct for
your Notebook PC; using other adapter model may
damage the computer or other devices on the computer.

2. When unplugging the power cord, always hold the
connector part of the cord

(), never pull the cord ().

Disconnecting the AC power

1 - 14

M510C Series Notebook PC

Turning On/Off the Notebook PC

Now, when the AC adapter is connected, you are ready to use your computer.

Opening the Top Cover

First, open the top cover by pressing the cover button on the right side of the
computer (), and then lifting the top cover gently (). You can tilt the top
cover forward/backward to the optimal viewing position.

Opening the top cover

1 - 15

Turning On the Computer

1. Make sure that the computer
is connected to the AC power.

2. Press the power button .

Once pressed, the power button
will light Blue to indicate that
the computer is turned on; meanwhile, the Power LED on the right side
of computer lights Green.

3. When the computer is turned on, it will first perform a series of
diagnostic tests that is called Power-On Self Test (POST). Then, the
operating system (such as Microsoft Windows XP in this manual)
should start, and you can start to work with your Notebook PC!

Remind you...

Power-On Self Test

The POST (Power-On Self Test) is a software controlled diagnostic
test tool, which is a set of routines stored in a computer’s ROM
(read-only memory) that tests various system components such
as the memory, disk drives, and the keyboard to see whether
they are properly connected and operating. If problems are found
during booting, these routines alert the user by sounding a series
of beeps or displaying a message on the screen.

Pressing the power button

1 - 16

M510C Series Notebook PC

Turning Off the Computer

In Windows operating system, always use the “Shut Down” command of the
system to turn off the computer. This is the normal operating procedure that
can prevent the system problems.

1. Click Start () from the taskbar, and then select the Turn Off
Computer option ().

2. Click Turn Off () to turn off the system.

Turning off the computer

1 - 17

Remind you...

1. If you are working on a program, such as Microsoft Word,
you should save the data and close the program first, and
then turn off the computer. Otherwise, you may lose your
data.

2. Confirm that the Hard Disk In-use LED is OFF before
turning off the computer. Also, remember to remove any
CD disk from the drive.

3. Gently tilt down the top cover when you are closing the
cover, and make sure that the cover latches click into
place securely.

1 - 18

MS-XXXX Notebook

2 - 1

This chapter introduces the operating basics for your

Notebook PC, including the use of keyboard, touchpad, LCD

panel, hard disk drive, and optical storage device. It also

includes the advanced features such as audio and

communication functions.

Basics of Using

Notebook PC

2 - 2

M510C Series Notebook PC

2.1 Safety and Comfort Tips

The Notebook PC is a portable platform that allows you to work anywhere.
However, choosing a good workspace is important if you have to work with
your Notebook PC for long periods of time.

Your work area should have enough illumination.

Choose the proper desk and chair, and adjust their height to fit your
posture when operating.

When sitting on the chair, adjust the chair’s back (if available) to support
your back comfortably.

Place your feet flat and naturally on the floor, so that your knees and
elbows have the proper position (about 90-degree) when operating.

Put your hands on the desk naturally to support your wrists.

Adjust the angle/position of the LCD panel, so that you can have the
optimal view.

Avoid using your Notebook PC in the space where may cause your
discomfort (such as on the bed).

The Notebook PC is an electrical device, please treat it with great care to
avoid personal injury.

Set Up Your Work Environment

If you are a beginner to the Notebook PC, please read the following tips to make
yourself safe and comfortable during the operation.

2 - 3

Have a Good Work Habit

Have a good work habit is important if you have to work with your Notebook
PC for long periods of time; otherwise, it may cause discomfort or injury to you.
Please keep the following tips in mind when operating.

Change your posture frequently.

Stretch and exercise you body regularly.

Remember to take breaks after working for a period of time.

Adjust the angle
and position of
LCD panel.

Adjust the
desk’s height.

Keep your hands
and feet with
optimal comfort.

Setting up your work environment

Sit straight and keep
a good posture.

Adjust the
chair’s height.

2 - 4

M510C Series Notebook PC

2.2 Knowing the Keyboard

The Notebook PC’s keyboard provides all the functions of a full-sized 87/88­key keyboard, and an additional [Fn] key for specific functions on the computer.
The use of the keyboard can be divided into four categories: Typewriter keys,
Cursor keys, Numeric keys, and Function keys.

The Keyboard

2 - 5

The function of these Typewriter keys is the major function of the keyboard,
which is similar to the keys on a typewriter. It also provides several keys for
special purposes, such as the [Ctrl], [Alt], and [Esc] keys.

When the lock keys are pressed, the corresponding LEDs will light up to
indicate their status:

Typewriter Keys

Num Lock: Press and hold the [Fn] key, and then press this key to toggle

the Num Lock on and off. When this function is activated, you can use the
numeric keys that are embedded in the typewriter keys.

Caps Lock: Press this key to toggle the Caps Lock on and off. When
this function is activated, the letters you type are in uppercase always.

Scroll Lock: Press and hold the [Fn] key, and then press this key to toggle
the Scroll Lock on and off. This function is defined by individual programs.

The Typewriter Keys

2 - 6

M510C Series Notebook PC

The keyboard provides four cursor (arrow)
keys and [Home], [PgUp], [PgDn], [End] keys
at the lower right corner, which are used to
control the cursor movement.

Cursor Keys

The Backspace key, [Ins] and [Del] keys at the upper right corner are use for
editing purpose.

Move the cursor left for one space.

Move the cursor right for one space.

Move the cursor up for one line.

Move the cursor down for one line.

Move to the previous page.

Move to the next page.

Move to the beginning of the line (or document).

Move to the end of the line (or document).

The Cursor Keys

2 - 7

The keyboard provides a 15-key
numeric keypad, which is embedded in
the typewriter keys.

When the Num Lock is activated, you
can use these numeric keys to enter
numbers and calculations.

Numeric Keys

Remind you...

The numeric keys may lose function in some specific software
applications. If so, you may use the typewriter keys to input the
numbers, or connect an external numeric keypad.

This key is used to switch the typing mode between “insert”
and “overtype“ modes.

Press this key to delete one character to the right of the cursor,
and move the following text left for one space.

Press this key to delete one character to the left of the cursor,
and move the following text left for one space.

The Numeric Keys

2 - 8

M510C Series Notebook PC

Function Keys

Windows Keys

You can find the Windows Logo key ( ) and one Application Logo key ( )
on the keyboard, which are used to perform Windows-specific functions, such
as opening the Start menu and launching the shortcut menu. For more
information of the two keys, please refer to your Windows manual or online
help.

[Fn] Key

The keyboard provides a [Fn] key ( ) at the lower left corner, which is to be
used with another key to perform the alternative function of a key. This
combination of keys can be called “hot key” in operating your Notebook PC,
which allows you to perform some special functions easily and quickly. The
hot keys includes:

Switch the display output mode between the LCD, external
monitor, and Both.

Increase the LCD brightness.

Decrease the LCD brightness.

Decrease the built-in speaker’s volume.

Increase the built-in speaker’s volume.

Disable the computer’s audio function.

Force the computer into suspend mode (depending on the
system configuration).

+

+

+

+

+

+

+

2 - 9

2.3 Quick Launch Buttons

With these four Quick Launch Buttons, you can easily access the Internet, read
your E-mail, or launch your frequently used software application.

Email: to launch the E-mail application (such as Outlook
Express) to receive and send your E-mail.

Internet: to launch the web browser (such as Internet
Explorer) to surf the Internet.

Wireless LAN: to enable or disable the wireless LAN
function of your computer.

User-defined: allows you to define a software application
to launch.

Customizing the User-defined Button

You can customize this button to launch a specific software application.

1. If the button is not pre-defined, you can see the Search Key window as
pressing the button. In this window, click

Add

to define a program.

2 - 10

M510C Series Notebook PC

2. Enter a name for the defined button and click OK.

3. The desired program’s icon appears in the Search Key window,
indicating that the program is defined to the button. Click

Close

.

Now, you can use it to launch the defined software application. You can use
the Search Key utility to change the defined program of the button (see
Advanced Features in Chapter 3).

Input a name

2 - 11

2.4 Knowing the Touchpad

The touchpad integrated in your computer is a pointing device that compatible
with the standard mouse, allowing you to control the computer by pointing the
location of the cursor on the screen and making selection with its two buttons.

Cursor Movement Area

The pressure-sensitive area of the touchpad, allows you to place your finger
on it and control the cursor on the screen by moving your finger.

Left Button

Acts as the mouse’s left button.

Right Button

Acts as the mouse’s right button.

The Touchpad

2 - 12

M510C Series Notebook PC

The following table and diagrams provide some tips that you should know
when using the touchpad:

Using the Touchpad

Positioning and Moving: Place your finger on the touchpad (usually using

the forefinger), and the rectangular pad will act as a miniature duplicate of
your display. When you move your fingertip across the pad, the cursor on
the screen will move simultaneously in the same direction. When your
finger reaches the edge of the pad, lift your finger and replace it on a proper
location of the touchpad.

Point and Click: When you have moved and placed the cursor over an
icon, a menu item or a command that you want to execute, simply tap slightly
on the touchpad or press the left button to select. This procedure, called as
“point and click”, is the basics of operating your Notebook PC. Unlike the
traditional pointing device such as the mouse, the whole touchpad can act
as a left button, so that your each tap on the touchpad is equivalent to
pressing the left button. Tapping twice more rapidly on the touchpad is to
execute a “double-click”.

Drag and Drop: You can move files or objects in your computer by using
“drag-and-drop”. To do so, place the cursor on the desired item and slightly
tap twice on the touchpad, and then keep your fingertip in contact with the
touchpad on the second tap. Now, you can drag the selected item to the
desired location by moving your finger on the touchpad, and then lift your
finger from the touchpad to drop the item into place. Alternately, you can
press and hold the left button when you select a item, and then move your
finger to the desired location; finally, release the left button to finish the
drag-and-drop operation.

2 - 13

Remind you...

1. Do not place heavy/sharp objects on the touchpad; do
not scratch the surface of touchpad.

2. Clean the touchpad with soft dry cloth regularly to
prevent the dust and liquids on it.

3. When using the touchpad, keep your fingers and the
touchpad clean and dry for optimal performance. Do not
use excessive force when tapping on the touchpad.

Using the Touchpad

Put your wrist
on the desk
comfortably.

Move the cursor by
sliding your fingertip.

2 - 14

M510C Series Notebook PC

You can customize the pointing device to meet your personal needs. For
example, if your are a left-hand user, you may want to swap the functions of the
two buttons. In addition, you can change the size, shape, moving speed, and
other advanced features of the cursor on the screen.

To configure the touchpad, you can use the standard Microsoft or IBM PS/2
driver in your Windows operating system. The Mouse Properties in Control
Panel allows you to change the configuration.

Mouse Properties window

Configuring the Touchpad

2 - 15

2.5 The Hard Disk Drive

Your computer is equipped with a 2.5-inch IDE (Integrated Drive Electronics)
hard disk drive. The hard disk drive is a storage device with much higher speed
and larger capacity than other storage devices, such as the floppy disk drive
and optical storage devices. Therefore, it is usually used to install the operating
system and software applications.

The hard disk drive is a non-removable storage device in your computer.
However, you can upgrade it by replacing a lager capacity hard disk drive. To
do so, please refer to Upgrading Your System in Chapter 6.

Remind you...

1. To avoid unexpected data loss in your system, please
backup your critical files regularly.

2. Do not turn off the computer when the Hard Disk In-use
LED is on.

3. Do not remove or install the hard disk drive when the
computer is turned on. The replacement of hard disk
drive should be done by an authorized retailer or
service representative.

2 - 16

M510C Series Notebook PC

2.6 Using the Optical Storage Device

Your computer is equipped with an optical storage device, which is know as the
CD/DVD-ROM, CD-RW, DVD Combo and DVD Dual drive. The actual device
installed in your computer depends on the model you purchased.

Remind you...

1. The optical storage devices are classified as a Class 1
Laser products. Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.

2. Do not touch the lens inside the drive.

CD-ROM Drive: allows you to read CD disks, including audio CDs, and
CD-R/RW disks.

DVD-ROM Drive: allows you to read DVD disks and CD disks, including
movie DVDs, audio CDs, and CD-R/RW disks.

CD-RW Drive: allows you to create the CD-R/RW disks containing your
own contents.

DVD Combo Drive: a cost-effective solution that can work both as a DVD­ROM drive and a CD-RW drive.

DVD Dual Drive: a dual format recorder, allowing you to record both the

-R/RW and +R/RW formats.

2 - 17

The following instruction describes the general procedure when operating the
optical storage device, including the DVD-ROM drive.

1. Confirm that the computer is turned on.

2. Press the Eject Button on the drive’s panel (), and the CD tray will
slide out partially. Then, gently pull the tray out until fully extended
().

3. Place your CD in the tray with its label facing up. Slightly press the
center of the CD to secure it into place ().

4. Push the tray back into the drive.

Inserting the CD

Inserting the CD

2 - 18

M510C Series Notebook PC

1. Confirm that the computer is turned on.

2. Press the Eject Button on the drive’s panel, and the CD tray will
slide out partially. Then, gently pull the tray out until fully extended.

3. Hold the CD by its edge with your fingers, and then lift it up from the
tray.

4. Push the tray back into the drive.

Removing the CD

Remind you...

1. Confirm that the CD is placed correctly and securely in
the tray before closing the tray.

2. Do not leave the CD tray open.

2 - 19

If unfortunately you can not release the CD tray by pressing the Eject Button,
you can release it manually:

1. Confirm that the computer is turned off.

2. Insert a pointed object (e.g. a straightened clip) into the Emergency
Eject Hole (), and the CD tray will slide out partially. Then, gently
pull the tray out until fully extended ().

3. Remove the CD, and then push the tray back into the drive.

Releasing the CD Manually

Releasing the CD Manually

2 - 20

M510C Series Notebook PC

2.7 Using the Video Function

Your Notebook PC provides an outstanding video subsystem, including:

1. ATI Mobility Radeon 9600 video controller with 64MB SDRAM, and

2. 15-inch XGA/SXGA+/14.1-inch XGA TFT color LCD screen.

The power features of the ATI Mobility video controller include:

Powerful Video Controller

64-bit memory bus, with 64MB DDR SDRAM installed.

Integrated dual-channel LVDS interface, up to 85Hz per channel.

Integrated enhanced TV encoder with 10-bit DAC frequency.

Supports Dual independent displays (LCD/CRT, LCD/TV, TV/CRT).

Motion compensation and iDCT for MPEG2 playback acceleration.

Hardware-based DirectX 9 supported for 3D acceleration.

Remind you...

1. You are strongly recommended to install the video driver
included in the software CD of your computer to take full
advantage of the video subsystem.

2. When using the external CRT monitor as the display
output device, the resolution depends on the specification
of the connected CRT monitor.

2 - 21

Display Modes

The following table describes the resolution/color support of your Notebook
PC:

When connecting an external CRT monitor, the CRT monitor’s refresh rate
could be:

Mode CRT monitor (Hz) Simulscan

640 * 480 60, 72, 75, 80 60

800 * 600 60, 72, 75, 80 60

1024 * 768 60, 70, 75, 80 60

1280 * 1024 60, 75 60

1400 * 1050 60, 75 60

Mode CRT monitor only LCD Simulscan

640 * 480 8, 16, 32-bit color 8, 16, 32-bit color 8, 16, 32-bit color

800 * 600 8, 16, 32-bit color 8, 16, 32-bit color 8, 16, 32-bit color

1024 * 768 8, 16, 32-bit color 8, 16, 32-bit color 8, 16, 32-bit color

1280 * 1024 8, 16, 32-bit color 8, 16, 32-bit color 8, 16, 32-bit color

1400 * 1050 8, 16, 32-bit color 8, 16, 32-bit color 8, 16, 32-bit color

2 - 22

M510C Series Notebook PC

Configuring the Display Settings

Your Notebook PC has been set to a default resolution and colors when shipping:
Now, you can change the settings to meet your needs through the operating
system.

Changing the Resolution and Colors Quality

1. Click Start from the taskbar, and select Control Panel to open the
Control Panel window.

2. In the Control Panel, double-click the Display item to open the
Display Properties window.

3. In the Screen Resolution field, move the slide bar to adjust the
screen resolution; in the Color Quality field, select the desired colors
setting from the pull-down menu.

Adjust the
colors quality.

Adjust the screen
resolution.

2 - 23

Changing the Display Output Device

1. Click Start from the taskbar, and select Control Panel to open the

Control Panel window.

2. Double-click the Display item to open the Display Properties window.

3. Click the

Advanced

button to bring up the following window that

contains more settings.

4. Under the Displays tab, if you have connected the external display

device, such as the CRT monitor or TV, simply select the one you
want to use and click OK. (You can also use the hot key [Fn]+[F2] on
the keyboard to switch the display output device.)

2 - 24

M510C Series Notebook PC

2.8 Using the Audio Function

Connecting Audio Devices

Your Notebook PC is equipped with a audio subsystem. However, you can
also connect the external audio devices for a better audio quality when enjoying
your music and movie on the computer. The audio-out jack () allows you to
connect the speakers and headphones; the microphone jack () allows you to
connect the external microphone.

Remind you...

1. You are strongly recommended to install the audio driver
included in the software CD of your computer to take full
advantage of the audio subsystem.

2. When you connect the external speakers or microphone
and use them as your audio subsystem, the built-in
audio device will be disabled.

Connecting the Audio Devices

2 - 25

Volume Control

Double-click the Volume Control icon on the taskbar, and the Master Volume
dialog box will appear as shown below. You can move the slide bar to adjust the
volume.

If the Volume Control icon does not appear on the taskbar, click Start and
select Control Panel to open the Control Panel window. In the Control Panel
window, select the Sounds, Speech and Audio Devices item, and then the Sounds
and Audio Devices item to open the Sounds and Audio Devices Properties
window (as shown below).

Check the Place Volume icon in the
taskbar option and click OK. Now,
you can see the Volume Control icon
on the taskbar.

Check this option

1 - 26

MS-XXXX Notebook

2 - 1

Your Notebook PC provides you with the useful software

applications, as well as the required drivers for the system.

Using the Software

Applications

3 - 2

M510C Series Notebook PC

3.1 Using the Software CD

The Software CD is a compact disk which provides the necessary drivers and
software applications for your Notebook PC.

You want to install the operating system from your Windows Setup CD,
but not from the Recovery CD that included in the package.

You want to install the drivers and software applications manually.

When do I Need the Software CD?

Insert the Software CD into your CD/DVD-ROM drive, and the Setup program
should start automatically as shown below. Then, click the item you want to
install, and follow the on-screen instructions to complete the installation.

How to Use the Software CD?

Autorun Screen of the Software CD

3 - 3

Remind you...

1. If your computer is pre-installed with the Windows operating
system when purchased, the required drivers should be
installed in the system already. If not, you may need to
install the drivers manually from the Software CD included
in the package.

2. Please contact your local dealer for driver update
information.

3 - 4

M510C Series Notebook PC

To change the defined application:

1. Double-click the Search Key icon on Windows desktop to bring up
the Search Key window. In this window, click

Add

to re-define a program.

Search Key

2. Enter a name for the defined button and click OK.

Input a name

3.2 Advanced Feature

Your Notebook PC provides you with a practical utility: Search Key. Click the
Searchkey Utility item in the Autorun screen to install the program. The
Search Key utility allows you to define/re-define the application to be launched
when pressing the User-defined Quick Launch button. Once the button is
defined to launch some specific application, you can use this utility to change
the defined application of the button.

3 - 5

3. The desired program’s icon appears in the Search Key window,

indicating that the program is defined to the button. Click

Close

.

2 - 1

This chapter tells you how to manage the power effectively,

in order to maintain the longest battery life and increase the

productivity when you are using the computer.

Power Management

4 - 2

M510C Series Notebook PC

4.1 Introduction to the Power Source

The AC adapter included in your Notebook PC is a universal AC adapter that
can operate on any voltage ranging from 100 ~ 240V AC. This allows you to use
your computer at any place when traveling. The AC adapter is used as a
converter that transfers the alternating current (AC) to direct current (DC), to
supply power to your computer. Also, it can charge the battery pack when
connected.

The AC adapter consists of two parts: the adapter (n) and the power cord (o).

The AC Adapter

Your Notebook PC provides a universal AC adapter and a high-performance
Li-ion battery in the package, and it can operate either on the battery’s power or
AC power.

Remind you...

1. The AC adapter included in the package is correct for
your Notebook PC; using other adapter model may
damage the computer or other devices on the computer.

2. When unplugging the power cord, always hold the
connector part of the cord, never pull the cord.

The AC Adapter

4 - 3

The Battery Pack

The rechargeable Li-ion battery pack is an internal power source of the computer.
A fully charged battery pack can supply power to the computer up to 6.5 ~ 7
hours, depending on the actual use of your computer.

Charging the Battery

The battery pack can be charged while it is installed in the Notebook PC.
Connect the AC adapter to the computer, and it starts to charge the battery
automatically. Please charge your battery in a normal temperature environment,
ranging from 0OC (32OF) to 50OC (122OF). If the temperature is higher than 60OC
(140OF), it will stop charging to protect the battery pack. After the temperature
is down to 50OC (122OF), it resumes charging automatically.

During charging, the Battery Status LED ( ) on the right side of computer
glows Green. When the battery is fully charged (about 2.5 hours in power off
mode), the LED becomes OFF.

Alternately, you can check the charging status through the Power Meter in
Windows. The Power Meter icon is displayed on the taskbar as or ,
depending on the current power source. Double-click the icon to bring up the
Power Meter window, which contains the related information for your reference.

4 - 4

M510C Series Notebook PC

If the Power Meter icon does not appear on the taskbar, you can configure the
setting through Start menu.

1. Click Start and select Control Panel to open the Control Panel
window. Then, click the Performance and Maintenance item.

3. In the Performance and Maintenance window, click the Power
Options item to open the Power Option Properties window.

4. Under the Advanced tab, check
the Always show icon on the
taskbar option and click OK.

Check this option

Remind you...

1. The charging time depends on the system mode.
When the computer is turned on, it will take a longer
time (3~4 hours) to have the battery fully charged.

2. The Power Meter only provides an estimated value of
the battery power. The operating time allowed depends
on the actual use of your computer.

3. For more instructions on using and caring the battery
pack, please refer to Taking Care of Your Computer in
Chapter 7.

4 - 5

Changing the Battery Pack

You can purchase an additional battery pack from your local dealer, so that you
can use it as a spare when traveling.

To remove the battery pack:

1. Confirm that the computer is turned off.

2. Place the computer upside down gently.

3. Locate the Battery Unlock Button on the bottom side of the
computer.

4. Press and hold the button, and then push it outwards (n). The
battery pack will bound upwards slightly (o).

5. Remove the battery pack from the compartment.

Removing the Battery Pack

4 - 6

M510C Series Notebook PC

Replacing the battery pack:

1. Place the battery pack into the compartment.

2. Press down the battery pack until a “click” sound. The battery pack
will be locked automatically.

Remind you...

1. Do not try to disassemble the battery pack.

2. Please follow your local laws and regulations to dump
your used battery pack.

Replacing the Battery Pack

4 - 7

4.2 Managing the Power

The Windows XP operating system supports ACPI (Advanced Configuration
and Power Interface), which allows you to manage the computer power easily
and efficiently. With the ACPI function, the power can be distributed to different
components individually according to their needs. This is helpful to provide
you with the maximum battery usage or optimal system performance.

Power Options

In order to maintain sufficient power for optimal system operation, please set
up the most appropriate configuration for your computer. The following
instructions describe the Power Options setup procedures:

1. Click Start from the taskbar, and then select Control Panel to open
the Control Panel window.

2. Click Performance and Maintenance.

3. In Performance and Maintenance window, click the Power Options
item to open the Power Option Properties window.

4. Under the Power Schemes
tab, you can set up the most
appropriate configuration
for your computer.

Select one Power Scheme that
is best fit to your computer
(see the table in page 4-11 for
more instructions).

Set up the related
settings in these field.

4 - 8

M510C Series Notebook PC

5. Under the Alarms tab, you can activate the battery alarm function by
checking the options in Low battery alarm and Critical battery
alarm fields. Once activated, adjust the slide bar to set up the low or
critical power level (the default setting is 10%).

Click Alarm Action within the
fields to set up the actions
when the power has reached
the preset low or critical level.

Set up the actions:
Stand by, Hibernate,
or Shut down.

Check this option

Check this option

4 - 9

6. Under the Advanced tab, you can set up the actions when pressing
the power button, sleep button, and closing the LCD panel.

Set up the Power
buttons’ function:
Stand by, Hibernate,
or Shut down.

Remind you...

1. Pressing [Fn]+[

F12

] allows your computer to enter suspend

mode immediately.

2. When you are alarmed for the low battery power, please
save your data as soon as possible. Also, if available,
connect the AC adapter before you continue operating.

3. Do not use the card reader or other storage devices when
the battery power is low. The access time may be longer
than the time you can operate. Otherwise, you may lose
your critical data or files.

4 - 10

M510C Series Notebook PC

7. Under the Hibernate tab, you can activate Hibernation function by
checking the Enable hibernation option.

Check this option

Hibernation is a very useful function of the Windows operating system. When
you activate this function, the current and programs are saved to the hard disk
drive. Therefore, you do not need to close the current applications when you
are going to exit the operating system temporarily. The next time you press the
Power button, you can resume the previous status when you left off.

To enter the Hibernation mode, click Start and select Turn off Computer.
Press and hold the [Shift] key(n), so that the Stand By option changes to
Hibernate. Click Hibernate (o) to enter the Hibernation mode.

4 - 11

Intel® SpeedStep™ Technology

You Notebook PC is equipped with an Intel Mobile Processors with Intel
SpeedStep technology, which allows you to customize high performance
computing on your computer. When the computer is connected to the AC
adapter, it can run the most complex business and Internet applications with
maximum speed of processor. When the computer is powered by a battery, the
processor drops to a lower frequency (such as degrading to 600MHz by
changing the bus ratios and voltage), conserving battery life while maintaining
a high level of performance. Manual override allows you to boost the frequency
back to the high frequency when on battery, so that you can customize the
system performance to meet your needs.

Using Intel SpeedStep Technology

Since Windows XP has the Intel SpeedStep technology driver built into the
system, the processor performance is controlled under the Power Scheme setting
in the standard power options (see page 4-7). No additional program or interface
is employed to set the policy. The following table describes the policy used in
Windows XP.

Adaptive: Performance state chosen based on CPU demand.
Degrade: Starts at lowest performance state, then uses linear performance reduction

(stop clock throttling) as battery discharges.

None: Always runs at highest performance state.

Power Scheme AC Power Battery Power

Home/Office Desk None Adaptive

Portable/Laptop Adaptive Adaptive

Presentation Adaptive Degrade

Always On None None

Minimal Power Management Adaptive Adaptive

Max Battery Adaptive Degrade

1 - 12

MS-XXXX Notebook

2 - 1

BIOS (Basic Input/Output System) is a program for setting

up the configuration of the computer. To take full advantage

of your computer and connected peripheral devices, you

should configure the system through BIOS Setup. This

chapter provides the information of BIOS Setup Utility, and

guides you to configure the system for optimal use.

BIOS Setup

5 - 2

M510C Series Notebook PC

5.1 Using BIOS Setup Utility

You may need to run the BIOS Setup when:

An error message appears on the screen during the system booting up,
and requests you to run SETUP.

You want to change the default settings for customized features.

You want to reload the default BIOS settings.

When to Use BIOS Setup?

To run the BIOS Setup Utility, turn on the computer and press the [Del] key
during the POST procedure.

If the message disappears before you respond and you still wish to enter
Setup, restart the system by turning it OFF and On, or simultaneously pressing
[Ctrl]+[Alt]+[Delete] keys to restart.

How to Run BIOS Setup?

Remind you...

The screen snaps and setting options in this chapter are for
your references only. The actual setting screens and options
on your computer may be different because of BIOS update.

5 - 3

You can use only the keyboard to control the cursor in the BIOS Setup Utility.

Control Keys

Move the cursor left to select one menu title.

Move the cursor right to select one menu title.

Move the cursor up to select one item under the menu title.

Move the cursor down to select one item under the menu title.

Increase the setting value or make changes.

Decrease the setting value or make changes.

1) Open the selected item to change setting options.

2) Bring up a sub-menu when available.

In some items, press this key to change setting fields.

Bring up help screen providing the information of control keys.

1) Exit the BIOS Setup Utility.

2) Return to the previous screen when in a sub-menu.

+

5 - 4

M510C Series Notebook PC

Once you enter the BIOS Setup Utility, the Main menu will appear on the
screen. The Main menu displays the system information, including the basic
configuration.

5.2 Main Menu

AMI BIOS

This item displays the BIOS version and ID.

Processor

This item displays the information of CPU, including the type and speed.

System Memory

This item displays the information of memory.

5 - 5

System Time

This item allows you to set the system time. The time format is <hour> <minute>
<second>.

System Date

This item allows you to set the system date. The date format is <day> <month>
<date> <year>.

Day Day of the week, from Sun to Sat, which is

determined by BIOS (read-only).

Month The month from 01 (January) to 12 (December).

Date The date from 01 to 31.

Year The year can be adjusted by users.

Primary/Secondary IDE Master

The two items display the types of the primary and secondary IDE devices
installed in the computer. Press [Enter] to bring up a window showing the
detailed information of the device, including the device name, vendor, LBA
mode, PIO mode, and more.

5 - 6

M510C Series Notebook PC

The Advanced menu contains the I/O configuration of the system.

5.3 Advanced Menu

Legacy USB Support

Set to Enabled if your need to use any USB 1.1/2.0 device in the operating
system that does not support or have any USB 1.1/2.0 driver installed, such as
DOS. Set to Disabled only if you want to use any USB device other than the
USB mouse. Setting options: Disabled, Enabled, and Auto.

USB 2.0

Set to Enabled if you need to use any USB 2.0 device in the operating system
that does not support or have any USB 2.0 driver installed, such as DOS.
Setting options: Disabled and Enabled.

5 - 7

Intel(R) SpeedStep(tm) tech.

This item allows you to enable or disable Intel SpeedStep technology. When
set to Disabled, the system always operates in a conserve power mode (the
processor works at 600MHz). If you want optimize the processor, set this item
to Enabled, so that the processor’s speed will be controlled by the use of your
operating system and applications.

Remote Power On

When set to Enabled, you can boot up the system through onboard LAN
function.

5 - 8

M510C Series Notebook PC

The Security menu contains the security settings, which protects your system
against unauthorized use.

Security Settings

This field displays the status of security settings, including Supervisor Pass­word and User Password.

Change Supervisor/User Password

When you select the function, a message box will appear on the screen as
below:

5.4 Security Menu

Enter New Password

5 - 9

Type the password you want, up to six characters in length, and then press
[Enter]. The password typed now will replace any previously set password
from CMOS memory. You will be prompted to confirm the password. Retype
the password and press [Enter]. You may also press [Esc] to abort the selection
and not enter a password.

When the Supervisor Password is set, the new item User Access Level and
Password Check will be added in the menu. You can make further settings of
access right in the User Access Level item. Setting options: No Access, View
Only, Limited, and Full Access. The Password Check item is used to specify
the type of BIOS password protection that is implemented. Settings are de­scribed below:

Setup The password prompt appears only when end

users try to run Setup.

Always A password prompt appears every time when

the computer is powered on or when end users
try to run Setup.

To clear a set password, just press [Enter] when you are prompted to enter the
password. A message box will show up confirming the password will be disabled.
Once the password is disabled, the system will boot and you can enter Setup
without entering any password.

Remind you...

About Supervisor Password and User Password

Supervisor Password allows the user to enter and change the
settings of the setup menu; User Password only allows the
user to enter the setup menu, but do not have the right to
make changes.

5 - 10

M510C Series Notebook PC

Clear User Password

If you have set the User Password, select this item to disable the User Password.

Boot Sector Virus Protection

The item is used to set the virus warning feature for IDE Hard Disk boot sector
protection. If the function is enabled and any attempt to write data into this
area is made, BIOS will display a warning message on screen and beep. Set­tings options: Disabled and Enabled.

Hard Disk Security

This item allows you to set the Primary Master HDD User Password to protect
your hard disk drive.

5 - 11

The Peripheral menu contains the settings for your peripheral devices.

Parallel Port Address

This item is used to set the parallel port address. Setting options: Disabled,
378, 278, and 3BC.

Parallel Port Mode

This item allows you to select the operation mode for the onboard parallel port:
Normal, Bi-Directional, EPP, and ECP.

5.5 Peripheral Menu

5 - 12

M510C Series Notebook PC

The Boot menu allows you to set the boot-up configuration.

Quiet Boot

This item enables you to show the vendor logo on the boot-up screen. Set­tings options: Disabled and Enabled.

Network Boot Support

This item allows you to enable or disable the network boot-up function.

1st /2nd Boot Device

The two items allow you to set the sequence of boot devices where BIOS
attempts to load the disk operating system.

5.6 Boot Menu

5 - 13

RTC Power On Timer

When set to Enabled, you can set the date and time at which the RTC (real-
time clock) alarm awakens the system from suspend mode.

5 - 14

M510C Series Notebook PC

The Exit menu contains options of exiting BIOS Setup Utility.

Save Changes and Exit

Save the changes you have made and exit the utility.

Discard Changes and Exit

Exit the utility without saving the changes you have made.

Discard Changes

Abandon your changes and reload the previous configuration before running
the utility.

Load Optimal Defaults

Select this item to load the default settings for optimal system performance.

5.7 Exit Menu

2 - 1

You can expand the capabilities of your Notebook PC and

upgrade your system for your necessary. This chapter

introduces the installation of optional devices/components

for your Notebook PC.

Expanding and

Upgrading

6 - 2

M510C Series Notebook PC

6.1 Connecting the External Devices

The I/O (input/output) ports on the rear panel of the computer allow you to
connect peripheral devices. For the information of these I/O ports, please refer
to Quick Components Guide in Chapter 1.

Connecting the Peripheral Devices

Connecting the Peripheral Devices

6 - 3

Connecting the External Monitor

You can connect an external monitor to your computer through the VGA port
for a larger view with higher resolution. To connect the monitor:

1. Confirm that the computer is turned off.

2. Plug the monitor’s D-type connector into the computer’s VGA port.

3. Connect the monitor’s power cord, and then turn on the monitor.

4. Turn on the computer, and the monitor should respond by default. If

not, you can switch the display mode by pressing [Fn]+[F2].
Alternately, you can change the display mode by configuring the
settings in Display Properties of Windows operating system.

Connecting the TV

The S-Video connector of your computer allows you to use a TV to display the
computer images for your specific purpose, such as enjoying your DVD movies.
To connect a TV, you will need the S-Video cable (not included). Then, you can
configure the display settings as described in the section Using the Video
Function of Chapter 2.

Connecting the USB Devices

The USB 2.0 ports of your computer allow you to connect many peripheral
devices, such as the mouse, keyboard, speakers, modem, external hard disk
module, printer, and more. The USB-standard interface supports “plug-and-
play” technology, so that you can connect and remove the USB devices without
turning off the computer.

To connect the USB device, simply connect the cable of the device to the USB
port of your computer.

6 - 4

M510C Series Notebook PC

Connecting the IEEE 1394 Devices

The IEEE 1394 port of your computer is a next-generation serial bus that features
a high-speed transfer rate and the connection of up to 63 devices, allowing you
to connect many high-end peripheral devices and consumer electronic
appliances, such as the DV (digital video camera). The IEEE 1394 standard
interface supports “plug-and-play” technology, so that you can connect and
remove the IEEE 1394 devices without turning off the computer.

To connect the IEEE 1394 device, simply connect the cable of the device to the
IEEE 1394 port of your computer.

Connecting the Printer

If your printer has a parallel interface, you can then use the 25-pin D-sub
parallel port on the computer to connect the printer. The following instruction
describes the general procedure to connect a printer:

1. Turn off the computer.

2. Connect one end of the printer cable to the computer’s parallel port,
and the other end to the printer.

3. Connect the power cord and turn on the printer.

4. Turn on the computer, and the system will detect a new device.
Install the required driver.

For further instructions, please refer to your printer’s manual.

6 - 5

Using the LAN

The RJ-45 connector of the computer allows you to connect the LAN (local
area network) devices, such as a hub, switch, and gateway, to build a network
connection. This built-in 10/100 Base-T LAN module supports data transfer
rate up to 100Mbps.

The following diagram describes the basic connection in a network environment.
For more instructions or detailed steps on connecting to the LAN, please ask
your MIS staff or network manager for help.

Connecting the Communication Devices

Remind you...

You are strongly recommended to install the LAN driver included
in the software CD of your computer to take full advantage of the
LAN feature.

Connecting the LAN Device

6 - 6

M510C Series Notebook PC

Using the Modem

The built-in 56Kbps fax/data modem allows you to use a telephone line to
communicate with others, or to dial-up to connect the Internet.

The following diagram provides the basic connection of modem. For more
instructions or detailed steps on dialing-up through the modem, please ask
your MIS staff or Internet service provider (ISP) for help.

Connecting the Modem

Remind you...

1. To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord.

2. You are strongly recommended to install the modem
driver included in the software CD of your computer to
take full advantage of the modem feature.

6 - 7

The PC card slot of your computer allows you to install comprehensive Type­II PC cards that support various functions for your necessary, including the
LAN/WLAN card, modem card, and memory card.

The following instruction provides you with a basic installation for the PC
card, including how to install and remove it. For more information, please refer
to the manual of your PC card.

Installing the PC card

1. Locate the PC card slot on your notebook computer. If there is the
dummy card in the slot, remove it first.

2. Insert the PC card into the slot (usually with its label facing up) and
push it until it is firmly seated.

Installing the PC Card

PC card slot

Installing the PC card

6 - 8

M510C Series Notebook PC

Remind you...

1. Do not hold the “golden finger” when installing the PC
card; otherwise, it may cause interference or damage to
the PC card.

2. Before removing the PC card, you should stop the device
in Windows operating system.

Removing the PC card

1. Press the Eject Button to make it stretch out.

2. Push the Eject Button (n) and the PC card will slide out slightly.
Then, pull it out of the slot (o).

Eject button

Removing the PC card

6 - 9

If you connect any peripheral device to your system, the Safely Remove
Hardware icon ( ) will appear on the taskbar. Double-click the icon to bring

up the Safely Remove Hardware dialog box. You can see all connected peripheral
devices here. If you want to remove any of the devices, move the cursor to the
device and then click

Stop

.

6.2 Safely Remove Hardware

Select

The following dialog box is to confirm
the device to be removed. Click

OK

to

continue.

You have successfully removed the device. Click

Close

to exit.

6 - 10

M510C Series Notebook PC

You can upgrade your Notebook PC through the following ways:

1) adding memory to a maximum of 2GB.

2) replacing the hard disk drive.

3) replacing the CPU.

Please NOTE that system upgrade should be done by an authorized retailer or
service representative; otherwise, it will void your warranty.

6.3 Upgrading your System

2 - 1

To ensure a trouble-free operation and reduce the risk when

working, you should take good care of your computer. This

chapter provides the basic guidelines to protect your

computer and critical data.

Caring Your

Notebook PC

7 - 2

M510C Series Notebook PC

7.1 Protecting Your Notebook PC

We understand that the Notebook PC is a valuable investment and how
important the data stored in your system meant to you. Therefore, we provide
the following suggestions to protect your system.

Locking Your Computer

When you use the computer in the public area, you can secure your computer
on the immovable object (such as a desk) by connecting a Kensington­compatible lock.

1. Loop the cable around the immovable object.

2. Plug the lock into the Kensington Lock hole of the computer, and
lock it up with the key.

3. Keep the key in a safe and personal location.

The Kensington lock is not included in your package; however, it is available
in the computer store. It can protect your computer from being stolen.

Locking Your Computer

7 - 3

Setting Up Password

Power-on Password

You can protect your computer from
unauthorized use by setting up a boot
password. Once the boot password
is set, it will bring up a dialog box
requesting for the password whenever
the computer is turned on.

The boot password is stored in the
BIOS. To set up the password, please
refer to the instruction in Chapter 5.

Operating System Password

In addition to the boot password, you can also set up the password in the
operating system, such as the login password and screen saver password.
Once the login password is set, it will ask you to enter the user name and
password when logging in Windows.

For more information on setting the system password, please refer to the manual
or online help of your operating system.

Remind you...

1. Remember the passwords once they are set. If,
unfortunately, you forgot the passwords, please contact
your local dealer for assistance.

2. You are recommended to set up the password; it can
protect your computer from being used by unauthorized
users.

7 - 4

M510C Series Notebook PC

Using the Anti-Virus Protection

About Computer Virus

In one word, the computer virus is a program that replicates; therefore, it will
need to attach itself to other program files, such as .exe, .com, .dll files. The
virus start to wreak havoc within the computer whenever these executable
programs execute. The destructive portion of a virus can range from overwriting
critical information stored on your hard disk’s partition table to scrambling the
numbers in your spreadsheets to just taunting you with sounds, pictures, or
obnoxious effects.

Remind you...

To know more about the computer virus and anti-virus
application, please refer to the document or online help of
the software.

7 - 5

With your Notebook PC, you can use the computer with more versatility, and
in more situations than ever before. Empowered by its light weight design and
optimized battery life, you can bring it to presentation and meetings whenever
and wherever you want.

To better help our frequent-flying users work with their Notebook PCs, we
have put up some tips for them to take care of the units.

Bring the fully charged Notebook PC to meetings for long-time use. If
the meeting time is longer than 4 hours, you are recommended to prepare
a second battery pack or an AC adapter.

Store your Notebook PC in a cool and dry place if you can not bring it
with you. Long-time exposure to temperature and humidity fluctuation
may cause malfunction of the system.

Carry your Notebook PC as a carry-on luggage. The airport X-ray
detector is OK but the handheld metal detector is not acceptable.

Use power cord and connector that are appropriate for the country to
which you are traveling.

7.2 Tips for Traveling