Page 1
User's Guide
Notebook
Computer
i
Page 2
Page 3
1
Preface
Copyright 2003
All Rights Reserved. Document Number G733
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part of
the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or documentation,
even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or other
means in any form without prior written permission of the manufacturer.
Trademarks
AMI is a trademark of American Megatrends Inc. AutoCAD and Autoshade are trademarks
of Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International Business Machines
Corp. Lotus, 1-2-3, and Symphony are trademarks of Lotus Development Corp. Windows,
Word, MS-DOS, and Microsoft are trademarks of Microsoft Corp. VESA is a trademark of
Video Electronics Standards Association.
Other product names mentioned herein are used for identification purposes only and may be
trademarks and/or registered trademarks of their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this manual, the
manufacturer and distributor assume no liability resulting from errors or omissions in this
manual, or from the use of the information contained herein.
Page 4
Notices
Federal Communications Commission Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in
accordance with the instruction manual may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
2
Page 5
Notice:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. Shielded interface cables and a
non-shielded AC power cord must be used in order to comply with emission limits.
This equipment is to be used with power supply:
I/P: 100-240 Vac, 50-60Hz, 1.5A
O/P: 19Vdc, 4.74A
There is no internal power supply.
Canadian DOC Notice For Class B Computing Devices
This Class B digital apparatus meets all requirements of the Canadian Interference - Causing
Equipment Regulations.
Cet appareil numerique de la classe B repecte toutes les exigences du Règlement sur le
matèriel brouilleur du Canada.
3
Page 6
This page is intentionally blank
4
Page 7
Table of Contents
Chapter 1: Before you Start ................................................................................. 9
Conventions of This manual ...................................................................................................10
Things you must remember before working on your computer ...............................................17
Chapter 2: Introduction...................................................................................... 19
Welcome to the Notebook PC................................................................................................. 20
Unpacking the Notebook ........................................................................................................ 20
Features ..................................................................................................................................20
Getting to Know Your Computer............................................................................................ 24
Chapter 3: Getting Started................................................................................. 37
Connecting to a Power Source ................................................................................................38
Turning On Your Notebook Computer.................................................................................... 39
Operating on Battery Power.................................................................................................... 40
Chapter 4: Using the Notebook Computer........................................................ 43
Adjusting the LCD Screen Display ......................................................................................... 44
A Tour of the Notebook’s Keyboard....................................................................................... 45
The TouchPad......................................................................................................................... 46
Connecting an External Tracking Devices ..............................................................................47
The DVD-ROM/Combo.......................................................................................................... 48
PCMCIA Cards and Expansion Sockets.................................................................................. 49
Power Saving Modes ..............................................................................................................50
Chapter 5: Desktop Operation ........................................................................... 55
Audio...................................................................................................................................... 56
Connecting Peripheral Devices ............................................................................................... 57
5
Page 8
Chapter 6: Configuring & Maintaining Your System ...................................... 61
Introduction ............................................................................................................................62
Chapter 7: The Software Utilities Disks ............................................................ 71
AutoRun Installation............................................................................................................... 72
Manual Installation ................................................................................................................. 75
VGA Utilities.......................................................................................................................... 76
Chapter 8: Troubleshooting............................................................................... 83
Locating a Problem................................................................................................................. 84
Checking Cables and Connections .......................................................................................... 84
The Power-On Self Test..........................................................................................................85
General Hardware Problems ...................................................................................................86
Contacting Your Dealer ..........................................................................................................89
Chapter 9: How do I expand my Notebook ...................................................... 91
Upgrading your Memory......................................................................................................... 92
Easy to Upgrade HDD Module ...............................................................................................95
CPU Upgrade.......................................................................................................................... 96
Removing the DVD-ROM/Combo Drive ................................................................................ 98
Appendix A: Specification ................................................................................. 99
Detailed Notebook Specifications......................................................................................... 100
6
Page 9
Personal Inventory
This Notebook computer system is designed for years of productive and pleasurable
computing. Use this section to keep notes about details of your purchase. Update this
section when you add new options.
Date of Purchase:
Dealer’s Name:
Phone:
Address:
E-Mail Address:
WWW Site:
Serial Number:
CPU Type:
Hard Disk Capacity:
Memory Capacity:
Optional Equipment:
7
Page 10
8
Page 11
Before you Start
1
9
Page 12
Conventions of This manual
Use this manual will help you get the most from your notebook computer.
• If you are an experienced user of computers and/or Microsoft’s Windows operating
systems, you might find it useful to read the Quick Start Guide that comes along with your
accessories.
• If you are a less experienced user, you should through the manual carefully before using
your system.
Whether or not you are an experienced user, you should consult on the Troubleshooting
Chapter if you encounter any problems with your notebook.
The check mark symbol indicates that you should take note
on every detailed information when you encounter some
function that might be useful when you are using your
notebook.
The pencil symbol identifies information which is important
for you to read to avoid damage to the computer.
This warning cautions you against actions which might be
destructive to your data or might disrupt proper system
operation.
10
Page 13
Safety Precautions
This section is designed to assist you in identifying potentially unsafe conditions while
working with this product. Required safety features have been installed in the computer to
protect you from injury. However, you should use good judgment to identify potential safety
hazards:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Please read these safety instructions carefully.
Please keep this User's Manual for later reference.
Please disconnect this equipment from AC outlet before cleaning. Don't use liquid
or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
For pluggable equipment, that the socket-outlet shall be installed near the
equipment and shall be easily accessible.
Please keep this equipment from humidity.
Lay this equipment on a reliable surface when installed. A drop or fall could cause
injury.
Make sure to use the right voltage for the power source when connecting the
equipment to the power outlet.
Place the power cord in such a way that people can not step on it. Do not place
anything on top of the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not use for a long time, disconnect the equipment from the main
power outlet to avoid being damaged by transient overvoltage.
Never pour any liquid into the opening, this could cause fire or electrical shock.
Never open the equipment. For safety reason, the equipment should only be opened
by a qualified service personnel.
If on the following situations arises, get the equipment checked by a service
personnel:
11
Page 14
a.
b.
c.
d.
e.
f.
14.
15.
16.
17.
A.
B.
The Power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work according to the
user's manual.
The equipment has dropped and damaged.
If the equipment has obvious sign of breakage.
Do not leave this equipment in an environment unconditioned, storage temperature
above 60°C (140°f), it may damage the equipment.
The unit can be operated at an ambient temperature of max. 35°C.
The sound pressure level at the operators position according to IEC 704-1: 1982 is
equal or less than 70 dB(A).
Power Cord Requirements
The power cord set used with the AC adaptor must meet the requirements of the
country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The
following information explains the requirements for power cord set selection.
• The cord set must be approved for the country in which it is used.
• The appliance coupler must have a configuration for mating with a
CEE22/EN6032/IEC 320 appliance inlet.
For U.S. and Canada:
• The cord set must be UL Listed and CSA Certified.
• The minimum specifications for the flexible cord are No. 18 AWG.
For Japan:
• All components of the cord set must bear a “PSE” or “ T ” mark and
registration number in accordance with the Japanese Dentori Law.
12
Page 15
• The minimum specifications for the flexible cord are .75m㎡ conductors.
C.
18.
19.
20.
21.
For Other Countries:
• The cord set fittings must bear the certification mark of the agency
responsible for evaluation in a specific country.
• The flexible cord must be of a HAR (harmonized) type H05VV-F.
• The cord set must have a current capacity of a least 2.5 Amperes and
voltage rating of 125 or 250 Vac.
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons. These
precautions includes the following:
• Do not use this product near water, for example, near a bathtub, washbowl,
kitchen sink or laundry tub, in a wet basement or near a swimming pool.
• Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
• Use only the power cord indicated in this manual.
Do not use the AC adapter near open water or other liquids. Never spill liquid into
the AC adapter.
Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open
avoid exposure to beam.
Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer's instructions. Never remove the battery pack while
the power is on as this may result in data loss when the system loses power.
Wichtige Sicherheitshinweise
1. Bitte lesen Sie diese Hinweis sorgfältig durch.
13
Page 16
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
a.
b.
c.
d.
Heben Sie dirse Anleitung für den späteren Gebrauch auf.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine
Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.
Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und leicht zugänglich
sein.
Das Gerät ist vor Feuchtigkeit zu schützen.
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Beschädigungen hervorrufen.
Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.
Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es
sollte auch nichts auf der Leitun abgestellt werden.
Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das
Gerät gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen.
Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und
von einer qualifizierten Servicestelle zu Überprüfung.:
Netzlabel oder Netzstecker sind beschädigt.
Flüssigkeit ist in das Gerät eingedrungen.
Das Gerät war Feuchtigkeit ausgesetzt.
Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
14
Page 17
e.
f.
14.
15.
16.
17.
A.
B.
C.
Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie.
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC.
Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte
überschreiten.
Anforderungen an das Stromkabel
Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen
des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die
Netzspannung 100-120 oder 200-240V Wechselspannung beträgt.
• Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen
sein.
• Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320
Buchse passen.
Für die USA und Kanada:
• Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein.
• Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG.
Für Japan:
• Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori
Law mit einem „PSE“ or „T”-Symbol markiert sein
• Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter.
Für andere Länder:
15
Page 18
• Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle,
die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist,
tragen.
• Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein.
• Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere
haben und Spannungen von 125 oder 250 V Wechselstrom gestatten.
18.
19.
20.
21.
Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden
Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und
Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte:
• Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel
Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten Kellerräumen
oder in der Nähe von Schwimmbecken.
• Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während eines
Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages.
• Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der
Nähe des Lecks befindet.
• Benutzen Sie nur solch ein Stromkabel, wie in dieser Anleitung beschrieben.
Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen
Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil.
Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer Laserstrahl,
vermeiden Sie Kontakt mit dem Strahl bei offenem Gehäuse.
Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird.
Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der
vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den
Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei
eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten.
16
Page 19
Things you must remember before working on your computer
Let your computer acclimate itself
Your notebook can easily stand temperature extremes but it doesn’t like rapid changes in
temperature, like going from the cold outdoors to a warm office. Rapid changes in
temperature can cause water droplets to condense inside your case, threatening to damage the
electronic parts inside.
After receiving your notebook when it’s hot or cold outside, try not to power up the computer
immediately, let the computer adjust to the room temperature gradually at least for three to
four hours.
If your system arrives in cold weather, do not apply power to
the computer or monitor until they have been allowed to come
to room temperature.
Heat, Cold, Humidity, and Glare
Find a suitable place for your computer that’s not too hot, too cold, too dark, or too bright.
Glare can make it hard to read the screen.
• Try to avoid the computer components from being destroyed if it is over heated, so try to
allow plenty of room for air to circulate around the case.
• Do not block the ventilation opening.
• Do not place your computer in direct sunlight.
17
Page 20
Suitable place to work
Your computer will run well wherever you’re comfortable but extremes of temperature and
humidity can be challenging to your system’s parts.
There are some things you can tolerate that the computer can’t – things like static electricity,
dust, water, steam and oil. In case you decide to pull over for roadside computing, try to
choose a clean, comfortable work area for your system.
A lithium-ion battery pack will be available when you are traveling. If you are running your
system for the first time on battery power, remove the battery from the package, install it into
the system and recharge the battery to fully prepare for service.
18
Page 21
Introduction
2
19
Page 22
Welcome to the Notebook PC
Congratulations on your purchase of the Notebook PC. Your Notebook features the latest
advances in portable computing technology. The Notebook’s modular design provides
maximum expandability without compromising portability. The high-performance CPU and
enhanced IDE hard drive provides you with extra processing power for handling complex
graphics and running large programs.
One PCMCIA slot gives you the ability to use standard PCMCIA cards, such as a LAN
adapter or memory cards.
Unpacking the Notebook
The Notebook comes securely packaged in a sturdy cardboard shipping carton. Upon
receiving your Notebook, open the carton and carefully remove the contents. If anything is
missing or damaged, please contact your Notebook dealer immediately. The shipping carton
should contain the following items:
• The Notebook computer
• An AC adapter
• An AC power cord
• Software Drivers CD
Do not throw the packaging materials away. You may need them later if you have to ship the
computer for repairs.
Features
This section provides an overview of the Notebook’s features. For more detailed information
see the Specifications section in Appendix A.
20
Page 23
The Notebook’s hardware has the following features:
CPU
The microprocessor (CPU) is the key hardware feature; it is the brain of the computer,
performing all the computing functions and orchestrating the actions of the system.
Upgradeable System Memory
The Notebook has a 64-bit memory bus.
Display
The LCD assembly is field-interchangeable and comes with the following display
options: 14.1”/15.0” TFT XGA
Removable HDD Module
The Notebook comes with a 2.5" (9.5mm maximum height) hard disk installed. The
HDD supports PIO mode 4. The hard drive can also be easily removed and replaced
with a second hard drive for the purpose of data backup or expansion. The Notebook
supports HDDs with capacities of 1.44GB or above.
Removable CD-ROM
The high speed built-in CD-ROM drive allows you to take advantage of the wide array
of multimedia titles available, and can be swapped with a Digital Versatile Disk (DVD)
ROM drive, or a second HDD.
Windows 95 Enhanced Keyboard
The Notebook keyboard uses a standard QWERTY layout with the addition of special
function keys and an embedded numeric keypad for number intensive data entry. The
Notebook’s enhanced keyboard design emulates a full-size desktop keyboard and
supports multiple language formats.
Your keyboard supports Windows 95 by incorporating two Windows specific keys.
With the two Windows 95 keys you will be able to access and take advantage of the
many time-saving features of Windows 95 software.
21
Page 24
Pointing Device
The TouchPad is a pressure-sensitive pointing device. It allows you to move the cursor
around the screen and make selections just as with a conventional mouse. The
TouchPad can be used concurrently with an external PS/2 mouse.
Battery and AC Power System
The Notebook can operate on two power sources; an AC Adapter, or the rechargeable
battery module pack.
The AC Adapter has automatic 100-240V line switching which will automatically check
the power voltage coming out of the wall and adjust it to the voltage your computer
requires.
The system will automatically recharge the battery pack in the Notebook by using the
AC Adapter. By using the power management features and using batteries, the
Notebook can operate on battery power for approximately 2 to 2.5 hours.
PCMCIA Interface
Your Notebook’s PCMCIA interface supports multi-function (combo) cards and Zoomed
Video. PC cards accommodate a number of expansion options, including memory
cards, modems, hard disks, and network adapters.
Parallel Port
The Notebook has a 25-pin parallel port, which is most commonly used to connect a
printer or Pocket LAN to the computer. The parallel port supports both EPP and ECP
capabilities.
USB Ports
USB (Universal Serial Bus) connectors are available for you to connect USB devices.
The USB is a personal computer bus endorsed by Intel and others that has a total
bandwidth of 1.5MB per second, making it much faster than conventional serial ports.
Contact your dealer for details on purchasing a USB device.
22
Page 25
Audio System
The Notebook’s sound system includes amplified output, two built-in 1 watt stereo
speakers, a manual volume control and a built-in microphone.
Audio Port
The Notebook comes with a Line in for connecting audio equipment for use with the
multimedia system; and a Line out for connecting stereo speakers, a headphones jack,
and a microphone jack.
VGA Port
At the rear of the Notebook there is a 15-pin VGA connector for connecting an external
CRT monitor.
Keyboard Controls
The Notebook provides a host of hot key features that are a permanent part of the
computer’s operation. Some affect the LCD video display, while others control power
management.
Security
The password protection feature of your Notebook can prevent unauthorized people
from accessing important files and information on your computer
Because the Notebook computer is available in different
configurations, some of the features mentioned in this manual
might not be included on your computer or may differ slightly.
23
Page 26
Getting to Know Your Computer
Opening the LCD Panel
At the front of the Notebook you will find a retaining latch on the display panel that locks the
display in closed position when the Notebook is not in use.
1.
2.
3.
Locate the display latch on the front of the unit. Slide the latch until the display
panel releases.
Raise the LCD screen and the machine will go to incline position.
At any time you can tilt the display toward or away from you to a comfortable
viewing position.
To avoid damage to the display panel:
1. Try not to slam the display upon closing it.
24
Page 27
2.
3.
Try not to place any object on top when it is closed or open.
Be sure the system is turned off or in suspend mode before you close the display
panel.
With the LCD screen open, you will see several features important for operating your
Notebook computer. Each of these features is briefly described below:
25
Page 28
1.
2.
3.
LCD Cover Release Latch
Slide this latch to the right to open the LCD cover.
LCD Screen
Your Notebook computer is equipped with a replaceable color Liquid Crystal Display
(LCD) screen that supports up to 1024 x 768 or 1400 x 1050 x 16M LCD resolution
utilizing an AGP BUS. A built-in backlight allows you to comfortably view the screen
even when ambient lighting is low.
Short-cut Keys
These two short-cut keys are assigned as functions for: Explorer and mail respectively.
1. Internet Explorer Button - Use this key to open the Internet Explorer.
2. Outlook Express Button - Use this key to open Microsoft's Outlook to
send/receive your mail.
26
Page 29
4. System Status Indicator Panel
The system status indicator panel keeps you informed of the computer’s operating status.
There are also two system status indicators — Power and Charge LED — on the left
side of the notebook. (Please refer to "The Left Side" section description)
Indicates the computer is accessing the PCMCIA drive.
Indicates that the computer is accessing the DVD-ROM drive.
Indicates that the computer is accessing the hard disk drive.
Indicates that the keyboard is in Num Lock mode.
Indicates when the keyboard is in Caps Lock mode. In this mode, the
keyboard produces uppercase text when you press a key. When you
press the Caps Lock key again, the indicator goes off and the
keyboard produces lowercase text.
Indicates when the keyboard is in Scroll Lock mode. Some
applications will move information across the screen differently when
Scroll Lock is on.
5. Power/Resume Button
Pressing this button for 1-2 seconds will turn on the system or pressing this button when
the computer is in Suspend mode will resume normal operation. Pressing this button for
4-6 seconds will also turn off the system.
27
Page 30
6.
7.
8.
9.
10.
11.
Keyboard
Your computer has an 88-key enhanced keyboard that provides all the functions of a
standard 101/102 key keyboard.
TouchPad
The TouchPad is hardware-compatible with the IBM PS/2 mouse and softwarecompatible with the Microsoft mouse.
Scroll Button
Use this button to scroll up and down the scrolling bar.
TouchPad Buttons
The buttons below the TouchPad correspond to the left and right buttons on a standard
mouse. The PS/2 compatible mouse will work with the Notebook PC’s TouchPad
simultaneously.
The Built-in Microphone
The built-in microphone is located to the left of the TouchPad.
Stereo Speakers
The internal speakers provide true stereo sound.
28
Page 31
The Left Side
1.
2.
3.
Kensington Lock
Allows you to connect a special computer lock to secure your system. You can purchase
a lock at most computer retailers.
USB Ports
Your computer includes four Universal Serial Bus (USB) 2.0 ports. USB2.0 is the latest
development in Plug and Play technology.
It will eventually replace the need for separate connectors for external keyboards, serial
ports, and parallel (printer) port.
1394 Ports
A fast external bus standard that supports data transfer rates of up to 400 Mbps (400
million bits per second). Can be used to connect up 63 external devices, also supports
isochronous data -- delivering data at a guaranteed rate.
This makes it ideal for devices that need to transfer high levels of data in real-time, such
29
Page 32
as video devices. Also supports both Plug-and-Play and hot plugging, and also provides
power to peripheral devices.
4.
5.
6.
7.
PCMCIA Socket Cover
Open this cover to access the PCMCIA socket. The computer’s PCMCIA socket lets
you extend the capabilities of your computer by inserting PC cards.
PCMCIA Socket Button
The computer has one PCMCIA type II socket
External Microphone Jack
This mono microphone jack is used to connect an external microphone.
Audio Line Out/SPDIF Jack
You can plug an external speaker, headphone or connect the line out jack to an audio
device such as a cassette recorder to record the notebook's audio output.
S/PDIF engine receives the digital format data from DVD-ROM or Combo drive,
regroup the date to be synchronous signal and de-multiplexes audio and other digital data.
30
Page 33
LED Indicator
A. Battery Charge/Suspend
An orange color light indicates the battery is in charging status. When it turn to green
color light it indicates the system is in suspend mode. When the indicator light turn off,
it indicates the system is in full charge.
B. Power On
This indicator will lit when the notebook is powered on.
31
Page 34
The Right Side
1. The Modem Port
This jack is an internal 56K voice/fax/data modem. You will connect your computer to
your phone line through this port.
Always disconnect all telephone lines from the wall outlet
before servicing or disassembling this equipment. To
reduce the risk of fire use only No. 26 AWG or larger
telecommunication line cord.
2.
3.
The DVD-ROM or DVD Combo
Your Notebook comes with a swappable 5.25" IDE 8X DVD-ROM or 16X Combo drive.
Smart Fan
The Smart fan prevents the Notebook’s CPU and other internal components from
becoming overheated. Keep this fan unobstructed to allow proper ventilation to the
Notebook’s internal components.
32
Page 35
4. DC IN Connector
Plug the AC adapter into this connector.
The Rear
1.
2.
3.
4.
Parallel Port
This port allows you to easily connect a parallel printer or plotter using this 25-pin bidirectional female port.
External CRT Port
This port allows you to easily connect an external VGA/SVGA display monitor into your
Notebook using the 15-pin female connector.
Smart Fan
The Smart fan prevents the Notebook’s CPU and other internal components from
becoming overheated. Keep this fan unobstructed to allow proper ventilation to the
Notebook’s internal components.
TV Out Port
This 4-pin S-Video port allows you to view the Notebook's Video output on a television
monitor.
33
Page 36
5. The LAN Port
This jack provides a standard RJ-45 connection for integration with an existing network
or a high-speed (DSL or cable) connection via a network cable.
When using a LAN, please use an EMI Shielding Cable to
minimize an inteference when transmitting.
6.
7.
Infrared Data Port
The Infrared Data Port allows your Notebook to become truly wireless. You can use this
port to transfer large amounts of data very quickly to any other machine (Notebook
computers, printers, etc.) which is also equipped with an IrDA-compliant IR port.
This allows you to print documents without any inconvenient cable hookups.
Ventilation Opening
Please don’t block this opening during operation of the system.
34
Page 37
The Bottom Panel
1.
2.
The CD-ROM/DVD-ROM/Combo Drive
Your Notebook comes with a swappable 24X (or higher) 5.25" IDE CD-ROM or DVDROM drive.
Battery Release Latch
Lift up this latch to release the battery from its bay.
35
Page 38
3.
4.
5.
Battery
Your notebook comes equipped with a factory-installed battery pack module. After the
battery runs down, the module can be removed and replaced with a charged battery.
CPU Compartment
This compartment will serve as upgrading your system CPU.
Hard Disk Drive
Your computer includes a 2.5-inch IDE hard disk drive (9.5mm in height). The
notebook PC's BIOS automatically detects IDE drive types.
36
Page 39
Getting Started
3
37
Page 40
Connecting to a Power Source
Connecting the AC Adapter
A universal AC adapter is provided to supply your computer with power and also charge the
computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to
240 volts, covering the standard voltages available in almost every country.
The power cord for the AC adapter requires a three-hole grounded AC outlet. To connect the
computer to an external power source:
1.
2.
Plug the AC adapter’s connector into the DC-IN connector on the rear of the
computer.
Connect the power cord to the AC adapter and then to a wall outlet.
38
Page 41
The best kind of AC power source to connect your Notebook
to is a UPS (Uninterruptible Power Supply). Lacking this,
use a power strip with a built-in surge protector. Do not use
inferior extension cords as this may result in damage to
your Notebook. The Notebook comes with its own AC
adapter. Do not use a different adapter to power the
computer and other electrical devices.
Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet
to recharge the battery.
Never turn off or reset your Notebook while the hard disk is
in use and the HDD status icon is lit; doing so can result in
loss or destruction of your data. Always wait at least 5
seconds after turning off your Notebook before turning it
back on; turning the power on and off in rapid succession
can damage the Notebook’s electrical circuitry.
Turning On Your Notebook Computer
Turn on your Notebook by pressing the power button. Hold the button down for a second or
two and release. The Power-On Self Test (POST) runs automatically.
After the POST is completed, the computer reads the operating system from the hard disk
drive into computer memory (this is commonly referred to as “booting” a computer). If your
OS (Operating System such as Windows ME, Windows 2000…. etc) is installed, it should
start automatically.
To turn the Notebook off, save your work and close all open applications, click on Start, then
Shut Down and select Shut down the computer and click "Yes" or press the power button for
4-6 seconds.
39
Page 42
Operating on Battery Power
Your computer comes with a rechargeable battery pack that lets you operate the computer
without an external power source. When the battery pack is fully charged, you can operate
the computer for approximately 2 hours under the following conditions:
• The battery pack initially has a full charge.
• No peripheral devices are installed.
• The disk/DVD-ROM drives run no more than 10% of the time.
Only use batteries that are approved by an authorized dealer
that is used on for this model only. All batteries are not the
same and therefore should not be treated as such. Using the
wrong battery could cause serious damage to your computer
and yourself through toxic emissions.
When you are operating only on battery mode, your system
CPU (over 2.1GHz) speed will automatically reduce into a
suitable frequency in extending the battery life. This will
prevent system loading over battery power rating.
When you unplug the AC adapter from your system, this will
reduce the brightness of your LCD screen display. This
process will also extend the battery life.
Inserting and Removing the Battery Pack
The battery pack should already be inserted in your Notebook computer when you unpack it.
If not inserted, follow these directions:
40
Page 43
1. Turn over the notebook with the front of the unit facing you and place it on a solid,
flat surface.
2. Angle the battery into the bay. The front edge of the battery should slide into the
grooves in the system case.
3.
1.
2.
Gently lower the battery into the bay and push it until it clicks securely in the bay.
To remove the battery pack:
Turn off the notebook, and disconnect the AC adapter. Close the LCD panel and
turn it over and place it on a solid, flat surface.
Lift the release latch to release the battery from the bay. At this time the battery
will now be angled slightly out of the bay.
41
Page 44
3. Hold the battery at the finger grip and lift it out of the compartment.
Charging the Battery Pack
The installed battery pack charges automatically any time the computer is connected to the
AC adapter and an external power source.
If this is your first time to use the battery, be sure to fully discharge the battery and recharged
until it is fully charged.
42
Page 45
Using the Notebook
Computer
4
43
Page 46
Adjusting the LCD Screen Display
The LCD screen display can be adjusted by the following key combinations.
KEYS FUNCTIONS
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10] Use this key combination to expand your video screen or reset to its
original size.
[Fn] + [F12] This key combination toggles the display between the LCD display and
an external CRT or simultaneous.
LCD Care
LCD screens are delicate devices that need careful handling. Please pay attention to the
following precautions:
• When you are not using the computer, keep the LCD screen closed to protect it from dust.
• If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface.
• Do not put your fingers or sharp objects directly on the surface and never spray cleaner
directly onto the display.
• Do not press on, or store any objects on the cover when it is closed. Doing so may cause
the LCD to break.
External CRT Display
You can hook up an external monitor through the 15-pin CRT connector. Five
configurations are available:
• LCD only
• CRT only
• Simultaneous display of the LCD screen and CRT monitor
• TV only
44
Page 47
• Simultaneous display of the TV screen and CRT monitor
You can switch between these display configurations by pressing the key combination [Fn] +
[F12]. For information on connecting an external display, please refer to Chapter Four.
A Tour of the Notebook’s Keyboard
The Notebook’s keyboard uses a standard QWERTY layout with the addition of special
function keys and an embedded numeric keypad for number intensive data entry. Your
keyboard supports Windows by incorporating the two Windows specific keys. With the two
Windows keys you will be able to access and take advantage of many of the timesaving
features of Windows software.
The function keys (F1-F12) on the top row of the keyboard, serve different purposes and
carry out different tasks depending on the application you are running.
The cursor (arrow) keys (which are all located in the lower right corner of your keyboard)
and the [PgUp], [PgDn], [Home] and [End] keys (which are located along the right edge of
the keyboard) allow you to move the active cursor of the computer to various locations on
the screen or within the document.
The embedded numeric keypad consists of 15 keys that make number intensive input more
convenient. Like the [Num Lock] key, these keys are labeled in blue on the keycaps.
Numeric assignments are located at the upper right of each key.
When the numeric keypad is engaged, the NumLock icon will appear in the System Window.
The keypad is activated by pressing the [Fn] + [NumLk] key. If an external keyboard is
connected, pressing the NumLock key on either the Notebook or external keyboard will
enable/disable NumLock of both keyboards in unison.
To disable the Notebook numeric keypad while keeping the keypad on an external keyboard
activated, use the [Fn] + [NumLk] hot key on the Notebook keyboard.
45
Page 48
The Notebook’s Hot Key Controls
KEYS FUNCTION(S)
Power Button Press this button once to power on or enter the suspend/resume
mode.
Press this button for more than 4 seconds to power off the
system.
Internet Button Open Internet WWW Home short-cut key
Email Button Open Email Reader short-cut key
[Fn] + [F2] This key combination turns on/off the volume.
[Fn] + [F3] Decreases the speaker volume.
[Fn] + [F4] Increases the speaker volume.
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10] Use this key combination to expand your video screen or reset
to its original size.
[Fn] + [F12] This key combination toggles the display between the LCD
display and an external CRT or simultaneous.
The TouchPad
The touchpad is a rectangular electronic panel located just below your keyboard. You can
use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the
buttons below the touchpad as left and right mouse buttons.
46
Page 49
TouchPad Precautions
The TouchPad is a pressure sensitive device. Please take note of the following precautions.
• Make sure the TouchPad does not come into contact with dirt, liquids or grease.
• Do not touch the TouchPad if your fingers are dirty.
• Do not rest heavy objects on the TouchPad or the TouchPad buttons.
You can use the TouchPad with Microsoft Windows as well as non-Windows applications.
Connecting an External Tracking Devices
The system will only enable you to use one tracking device whether it is an internal or
external tracking device.
47
Page 50
Data Storage and Retrieval
Data storage and retrieval are two of the most fundamental tasks you will perform when
working with your computer. The Notebook is equipped with a hard disk drive (HDD). The
HDD is removable allowing for easy upgrades.
The DVD-ROM/Combo
Features of the DVD-ROM/Combo Module
The features of the DVD-ROM/Combo drive are listed below.
• The Audio Play feature allows you to play music CDs
• Front panel load/unload button
• Supports CD-DA, DVD-ROM mode 1 and mode 2, Multi-Session Photo CD™, CD-
I/Video CD (pcs.)
• Low power consumption
• 12.7mm height
Precautions for Handling DVD-ROM/Combo Discs
• Always hold the disc by the edges, avoid touching the surface.
• Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the center
outward.
• Do not write or place objects on the surface of the disc.
• Store discs in a cool dry place not to damage the disc.
• Do not use benzene, thinners, or cleaners with detergent. Only use DVD-ROM cleaning
kits.
• Do not bend or drop the discs.
48
Page 51
Loading a Disc
To play a CD disc, follow the instructions listed below.
1.
2.
3.
1.
2.
3.
Push the DVD-ROM/Combo eject button on the CD drive door. Gently pull the
tray all the way out.
Carefully lift the DVD-ROM/Combo by the edges and make sure the shiny surface
is face down (the side with no writing on it). Carefully insert the DVD-ROM onto
the tray. Push the DVD-ROM down gently so that it snaps onto the center ring.
Push the tray back into the drive.
To remove a disk, do the following:
Check the LED display and make sure that the computer is not accessing the DVDROM drive.
Push the eject button and pull the tray all the way out.
Carefully pick up the CD disk by the edges and – while pressing down on the center
ring – remove the DVD-ROM/Combo from the tray.
Do not insert any foreign objects into the disc tray. If you experience difficulty when
ejecting the CD disk tray, stretch a paper clip (or use a pin or a thin metal rod) and insert it
into the emergency eject hole located on the right side of the front panel. The CD disk tray
should eject immediately. This procedure can also be used to remove a CD from the drive
when the Notebook is powered off.
PCMCIA Cards and Expansion Sockets
The Notebook features one PCMCIA expansion socket design to interface with one Type II
card.
49
Page 52
Inserting a PCMCIA Card
The computer will emit a medium tone followed by a high tone when a PC card is inserted.
When you eject a card, the computer will emit a high tone followed by a medium tone. You
can insert and remove a PC card whether the computer is turned On or Off.
Follow these instructions to insert a PCMCIA card:
1.
2.
Hold the PCMCIA card with the arrow side up and the connector side toward the
socket.
Align the card connectors with the socket and carefully slide into the socket until it
locks into place. The system will beep once to indicate that it has detected the PC
card.
To remove a PC card push the eject button, the button will pop-out, push the button again to
eject the PCMCIA.
When inserting a Type II PC card, make sure the connector is inserted in the socket. Before
ejecting a PC card, ensure that it is not being accessed by the System.
For example, if the message “Write protect error writing Drive x” is displayed, the user has
to change the write protect switch setting on the memory card. To change the switch setting,
(a) eject the card, (b) change the switch setting, and (c) re-insert the card.
Always disconnect all telephone lines from the wall outlet before servicing or disassembling
this equipment. To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord.
Power Saving Modes
This section contains information on the Notebook’s power system, including the AC
Adapter, the battery system, recharging the battery, and tips for conserving battery power.
The power system is comprised of two parts, the AC Adapter and the battery system. The
AC Adapter converts AC power from a wall outlet to the DC power required by the computer.
50
Page 53
The Battery Power System
A fully charged pack will provide approximately 2 hours of battery life depending on your
system configuration application it runs.
Before using the computer on battery power for the first time, check the battery status icon
on the Windows Toolbar to make sure the battery is fully charged.
See Battery Status later in this section for a description and explanation of the Windows
Battery icon. Charging the battery takes about 3 hours to charge when the system is in off
state. If possible, always charge the battery completely.
Removing the Battery Pack
To remove the battery pack from its compartment, please refer to Chapter Two, Inserting and
Removing the Battery Pack.
Preparing the Battery Pack for Use
Before using the battery pack for the first time, the Smart Battery IC within the battery pack
should be calibrated in order to get accurate reporting of remaining battery life status.
To calibrate the battery pack follows the instructions below:
1.
2.
3.
Insert the battery into the battery compartment and turn on the Notebook. If the
battery is completely without power go to the next step.
Otherwise, let the battery run down until the battery low-low warning beeps are
heard.
The system will automatically enter Suspend mode.
Turn the Notebook off. Connect the AC adapter and let the battery fully recharge.
When the battery charge indicator turns off, the battery is fully charged.
Turn On the notebook, let the battery run down until the battery is in low-low state
and you hear a warning beeps. The system will automatically enter the Suspend
mode. You can now connect the AC adapter.
51
Page 54
4. The battery pack is now calibrated properly.
In general, using the battery until the low-low battery-warning indicator appears and fully
recharges the battery each time (full discharge/charge cycle) will ensure the accurate
reporting of the battery gauge status.
Automatic Battery Pack Charging Function
You can automatically charge the battery pack by using the AC Adapter. The charge time is
about three hours when the Notebook power is turned off. The following table summarizes
the charging modes:
Charge Mode Charge Time
Fast 3 hours with the system off or in Suspend mode. The temperature
must be 25°C or below room temperature.
Pre-Charge A pre-charge is supplied to the Li-Ion battery pack.
Battery Status
Windows 98/ME/2000/XP has an applet in the Control Panel that will display an icon in the
Windows taskbar indicating when the Notebook is running on battery power or is attached to
the AC adapter.
This applet also displays a meter that indicates how much charge is remaining in the battery.
Battery Low Warning
When the pack initially reaches the “Battery Low” state approximately 10 ~ 15 minutes of
the usable battery life is left.
You will hear an audible beep signal every 1.5 seconds alerting you to the “Battery Low”
status. When the battery power reaches the “Battery Low Low” status the beeping sound will
accelerate.
Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or
connect AC power immediately; otherwise, you may lose your data.
52
Page 55
Sound Meaning
Continuous beeping
every 1.5 seconds
Battery Low: Indicates that there is 7 to 10 minutes
charge remaining.
Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes
of battery charge remaining. Save your work and turn
off the Notebook, or connect the AC adapter.
When there is only one minute of battery charge remaining, the Notebook will suspend to the
HDD and power off. You should connect AC power and resume to save your work.
Small Battery for the Real Time Clock
There is a small built-in battery pack that supplies power to the system in order to maintain
certain system information while the power is off. If the Notebook is left without a power
source for long period of time, this battery will be exhausted and system information will be
lost.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer's instructions. Never remove the battery pack while the power is on as this
may result in data loss when the system loses power.
Resetting the System
After installing a software application package, you may be prompted to reset the system to
load the changed operating environment. To reset the system, or “reboot,” press the [Ctrl] +
[Alt] + [Delete] keys simultaneously. This is known as “warm boot.” This key combination
acts as “software” reset switch when you encounter hardware or software problems, which
lock up the Notebook.
If this key combination does not shut down the Notebook, you can reset the Notebook by
using the Notebook’s power button. Should the Notebook lock up for some reason, pressing
this button powers the Notebook off.
53
Page 56
Adjusting the Brightness
To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower
left hand corner of the keyboard and press the [F7] key to reduce the brightness or [F8] to
increase the brightness.
54
Page 57
Desktop Operation
5
55
Page 58
Your notebook is capable of providing you with efficient and productive mobile computing;
it also has the speed and capacity to service as a desktop system.
This chapter discusses those functions of your notebook that are typical of desktop systems.
Audio
The Multimedia Sound System
The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of
education and entertainment multimedia software. The Notebook is equipped with two
internal stereo speakers, a microphone, and input audio ports for external audio units.
An external microphone can be connected to the microphone jack. External speakers or
headphones can be connected to the Notebook’s audio-out jack.
External audio devices can be connected to the Line in jack. All audio features are software
controlled. The Notebook’s multimedia sound system includes the following features:
• Supports Windows Sound System compatibility
• Full Duplex operation
• Dynamic filtering reduces noise and distortion rate
• 16-bit digitized audio playback
• A built-in microphone for convenient recording
• Two built-in stereo speakers
• Digitized audio recording through the Notebook’s built-in microphone or any external
source
Audio Volume Control
The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key
combination decreases the audio output volume; press the [Fn] + [F4] hot-key combination
increases the audio output volume.
56
Page 59
Audio Software
Your notebook comes equipped with an integrated sound system capable of providing you
with quality audio sound through the built-in speakers or through external speakers
connected via the system ports.
Sound Recording
Your system allows you to record sounds and store them as files using the microphone via
the microphone jack on the rear of the notebook computer. Check the Windows Help and
Support Center in Windows for information on using the various elements in sound recording.
For a high-quality sound, click on the "Volume Control" at the lower right end of your screen.
From the Volume Control windows, click on the "Advanced" tab, click and select the
"Microphone Boost" item.
Playing Sound Files
Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check the
Help and Support Center in Windows for information on the functions of the Media Player.
External Speakers and Microphone
The sound system is capable in providing high-quality sound to external speakers and
receiving and processing sounds from an external microphone or external sound source.
Connecting Peripheral Devices
Installing the External monitor
This machine allows use of an external monitor. After you have finished installing it, press
[FN]+[F12] simultaneously to change the display
57
Page 60
Installing the Printer
The installation of the printer is very easy. Simply connect the enclosed cable to connect the
notebook computer printer port to the printer. You also have to install the printer driver.
Please follow the instructions in the printer manual for installation.
Installing USB Devices
USB devices are Plug & Play, just plug the USB device into any USB port on the notebook
computer to use it.
There are some exceptions. Some devices will not be supported by the OS. In these cases
you follow the instructions in the device’s manual to install the proper drivers in order use
the USB devices.
Installing 1394 Devices
1394 is a very common transfer interface widely used in many audiovisual devices. There
are different sizes for 1394 plugs. The installation of 1394 devices is very easy, just follow
the illustrations. If the OS you use does not support the 1394 devices you plan to use, please
follow the instructions in the manual to install the proper drivers or software applications to
make the devices work.
Connecting to the network
Unless you are a technician, we do not recommend that you install to the Ethernet all by
yourself. The illustration only shows how to connect the notebook to the network, the actual
application and setting should be done following the instructions in the OS manual, or you
should ask for a technician’s professional assistance.
Installing the modem
Using the modem to connect to the Internet is a common practice. Connect the modem to
this notebook according to the methods described on the right, and then use a phone cable to
connect the slot on the modem to the jack of the phone line. The hardware installation is
complete.
58
Page 61
Then follow the instructions from your ISP (Internet Service Provider), to make the proper
connection to the Internet.
Connect peripheral devices to the computer's interface ports as shown below:
59
Page 62
60
Page 63
Configuring &
Maintaining Your
System
6
61
Page 64
Introduction
The BIOS (Basic Input and Output System) Setup program is a menu driven utility that
enables you to make changes to the system configuration and tailor your system to reflect
installed hardware or alter system performance. When the notebook computer is turned back
on, the system is configured with the values stored in CMOS.
Navigating through BIOS Setup
The Setup program has been designed to make it as easy to use as possible. If you
accidentally make a setting and don’t know which one to switch back to, the Setup program
has a hot key that allows you to return to the previous value.
Accessing the BIOS Setup Program
To access the BIOS Setup program, press the Del key after the notebook computer has run
through its POST.
Item Specific Help
On the right side of the Setup screen is an area labeled Item Specific Help. This area will list
navigation key shortcuts and information that is specific for the item that you are currently
editing.
The Menu Bar
The top of the screen has a menu bar with the following selections:
Standard CMOS Setup
Set the time and date. Configure disk drives.
Advanced CMOS Setup
Configure basic system performance parameters.
62
Page 65
Peripheral Setup
Configure I/O support for the Notebook computer.
To access the menu bar items, press the up or down arrow key on the keyboard until the
desired item is highlighted.
The Legend Bar
At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar
allow you to navigate through the various setup menus.
The following table lists the keys found in the legend bar with their corresponding alternates
and functions.
Legend Key
Function
Esc Jumps to the Exit menu or returns to the Main menu from a
submenu.
↑ or ↓
Moves the cursor up and down between fields.
PgUp/PgDn Set to modify the field selected.
F2/F3 Set the color (8 colors) of the BIOS Setup screen.
F10 Save and Exit.
Enter Will select a sub menu or show a range of options for a field.
Save Changes and Exit the Setup Program
Refer to the "Save Settings and Exit" section of this chapter for detailed information on
saving changes and exiting the setup program.
The Standard CMOS Setup
When the Setup program is accessed, the following screen appears:
63
Page 66
Date/Time
The current values for each category are displayed. Enter new values through the
keyboard.
Pri Master, Sec Master
Select one of these hard disk drive icons to configure the hard disk drive named in the
option.
The Advanced CMOS Setup
When the Setup program is accessed, the following screen appears:
64
Page 67
Auto Detect CPUandDRAM Frequency
Set this option to auto detect the system CPU and DRAM frequency.
The settings are Disabled or Enabled (default value).
Quick Boot
Set this option to Enabled to instruct AMIBIOS to boot quickly when the computer is
powered on.
The settings are Disabled or Enabled (default value).
1st Boot Device
This option sets the type of device for the first boot drives that the AMIBIOS attempts to
boot from after AMIBIOS POST completes.
The settings are Disabled, IDE-0, CD/DVD (default value), and Intel UNDI.
65
Page 68
2
nd
Boot Device
This option sets the type of device for the second boot drives that AMIBIOS attempts to
boot from after AMIBIOS POST completes.
The settings are Disabled, IDE-0 (default value), CD/DVD, and Intel UNDI.
3rd Boot Device
This option sets the type of device for the third boot drives that the AMIBOOS attempts to
boot from after AMIBIOS POST completes.
The settings are Disabled, IDE-0, CD/DVD, and Intel UNDI (default value).
TouchPad Support
Set this option to enabled or disabled the touchpad. The default setting is Enabled.
Password Check
This option enables password checking every time the system boots or when you run
AMIBIOS Setup. If Always is chosen, a user password prompt appears every time the
computer is turned on. If Setup is chosen, the password prompt appears if AMIBIOS is
executed.
Share Memory Size
This field shows the share memory size available.
The settings are 16M/32M (default value)/64MB
Graphic Win Size
This field shows the graphic win size available.
The settings are 64M (default value)/128M/256M
66
Page 69
The Peripheral Setup
TV Display Type
This field allows you to choose the television display option when using the TV out port.
The settings are PAL, NTSC (default value).
TV PAL Display Type
This field allows you to choose the television PAL system type.
The settings are PAL (default value), PAL-M, PAL-N.
OnBoard IR Port
This option specifies the IR port address for the IR Port.
67
Page 70
The settings are Auto, Disabled, 3F8h/COM1, 2F8h/COM2 (default value),
3E8h/COM3, 2E8h/COM4
IR Mode Select
This option specifies the infrared transmission method.
OnBoard Parallel Port
This option specifies the base I/O port address of the parallel port on the motherboard.
The settings are Auto (default value), Disabled, 378h, 278h and 3Bch.
Parallel Port Mode
This option specifies the parallel port mode.
The settings are EPP+ECP (default value), SPP, EPP and ECP.
Change Supervisor Password
This field allows you to set the Supervisor password. To set the Supervisor password,
highlight this field and press the [Enter] key. The following dialog box appears:
Enter new supervisor password:
Auto Configuration with Optimal Settings
The optimal default settings are best-case values that should optimize system performance.
To set the configuration, highlight this field and press the [Enter] key. The following
dialog box appears:
Load high performance settings [Y/N] ?
Battery Calibration
This option helps execute the calibration of the system battery.
68
Page 71
Execute Battery Calibration [Y/N] ?
Save Settings and Exit
This option saves your selections and exit the Setup program.
Save current settings and exit [Y/N] ?
Exit Without Saving
This option should only be used if you do not want to save the changes you have made to
the Setup program.
Quit without saving [Y/N] ?
69
Page 72
70
Page 73
The Software
Utilities Disks
7
71
Page 74
There are two separate procedures on how to install the driver: AutoRun installation and
Manual installation.
AutoRun Installation
• Follow the step-by-step procedures on the DVD-ROM to execute the “AutoRun”
application by selecting the topic of “Driver Installation”.
• To re-run the “AutoRun” installation, please refer to the procedures on the “Manual
Installation” for a more detailed explanation.
If you encounter this message when executing the Auto Run
in Windows 2000, please perform the following procedures:
Click on the “Start” – “Setting” – “Control Panel” – “System” –
“Advanced” tab – “Performance” tab – “Change” tab – reduce
the maximum Virtual Memory setting to 200MB.
Installing VGA Display Drivers for Win2K\XP
This section describes the operation and installation of VGA display software drivers
supplied on the Driver Utility DVD-ROM that is shipped with your computer.
1.
2.
3.
4.
Insert the DVD-ROM Driver into your DVD-ROM drive.
Click “Start” and select “Run”.
Type the following: D:\Driver\VGA\ Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
Click on “Setup” to begin the Installation Wizard.
72
Page 75
5. Follow the Wizard’s on-screen instructions to complete the installation.
6. Restart the system.
Intalling the Audio Driver for Win2K\XP
1.
2.
3.
4.
5.
6.
Insert the DVD-ROM Driver into your DVD-ROM drive.
Click “Start” and Select “Run”.
Type the following: D:\Driver\Audio\Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
Click on “Setup” to begin the Installation Wizard.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Intalling the LAN Driver for Win2K\XP
To install the LAN driver you must first remove the currently installed driver.
1.
2.
3.
4.
5.
6.
Insert the DVD-ROM Driver into your DVD-ROM drive.
Click “Start” and Select “Run”.
Type the following: D:\Driver\LAN\Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
Click on “Setup” to begin the Installation Wizard.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Installing the USB20 Driver for WinXP
To install the USB20 driver you must first remove the currently installed driver.
1.
2.
Insert the DVD-ROM Driver into your DVD-ROM drive.
Click “Start” and Select “Run”.
73
Page 76
3. Type the following: D:\Driver\USB20\USB20.exe (If D is not your DVD-ROM
drive, substitute D with the correct drive letter).
4.
5.
6.
Click on “USB20” to begin the Installation Wizard.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Please note that Window XP Service Pack 1 provides built-in
driver for USB 2.0. Do not install USB 2.0 driver from driver
CD if you already have Windows XP Service Pack 1
Installing the TouchPad Driver for WinXP
To install the touchpad driver you must first remove the currently installed driver.
1.
2.
3.
4.
5.
6.
Insert the DVD-ROM Driver into your DVD-ROM drive.
Click “Start” and Select “Run”.
Type the following: D:\Driver\Touchpad\Setup.exe (If D is not your DVD-ROM
drive, substitute D with the correct drive letter).
Click on “Setup” to begin the Installation Wizard.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Intalling the Modem Driver for Win2K\XP
To install the Modem driver you must first remove the currently installed driver.
1.
2.
3.
Insert the DVD-ROM Driver into your DVD-ROM drive.
Click “Start” and Select “Run”.
Type the following: D:\Driver\Modem\Prewell\Setup.exe (If D is not your DVDROM drive, substitute D with the correct drive letter).
74
Page 77
4. Click on “Setup” to begin the Installation Wizard.
5.
6.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Manual Installation
To install the driver manually, follow the step-by-step procedures described on each
individual section for a more clear installation.
Installing the CardBus Driver for WinXP
Please follow these instructions to install the cardbus driver:
1.
2.
3.
4.
5.
6.
From Start, click on the "My Computer" icon and click the "View System
Information".
Click on the "Hardware" tab from the "System Properties" dialog window.
Click the "Device Manager" button.
Click on the "PCMCIA adapters" , double click the "Generic CardBus Controller"
and click on the "Driver" tab.
Click the "Update Driver" tab and select the "Install from a list or specific location
(Advanced)" item and click "Next".
Select the "Include this location in the search" item and click on the "Browse"
button and specify for the designate location of your CD driver
d:\Driver\Cardbus\WinXP to proceed with the installation.
Installing the CardBus Driver for Win2K
Please follow these instructions to install the cardbus driver:
1. From your screen, click on the "My Computer" icon and use your mouse or
touchpad right button to select the "Properties" item.
75
Page 78
2. Click on the "Hardware" tab from the "System Properties" dialog window.
3.
4.
5.
6.
7.
8.
Double click to enter the "Device Manager" window.
Click on the "PCMCIA adapters",select the "Generic CardBus Controller" and click
on the "Driver" tab.
Click the "Driver" tab then click the "Update Driver" item.
Select the "Search for a suitable driver for my device (recommended)" item and
click "Next".
Select the “Specify a location” item and click “Next”.
Click "Browse" button and specify for the designate location of your CD driver
D:\Driver\Cardbus\Win2K to proceed with the installation.
VGA Utilities
After you have restarted Windows, open the “Control Panel” and double click on the
“Display” icon. From the “Display Properties” window, select the “Settings” tab and click
on the “Advanced” tab to enter the "SiS 651 Properties" window.
You will notice three new entries have been made in the Display Properties window: Display
Mode Setting, Video Setting, and Gamma Correction.
76
Page 79
Driver Mode Setting
The SiS's driver allows five simultaneous outputs to LCD only, CRT only, TV only,
LCD/CRT and TV/CRT. Before proceeding, be sure the monitor is connected to the
computer.
77
Page 80
Driver Mode
This define the two status of Single, Mirror and Multi Monitor (when an external monitor
is connected to your notebook computer).
• When the "Single" is selected, the display can only be seen on the notebook
computer LCD panel or external monitor.
• When the "Mirror" is selected, you can toggle between the LCD and CRT
display. Both the LCD and CRT screen display the same image.
Display Combination
This applies to the display that you prefer to use. The options are VGA1 and LCD2.
REMINDER:
The "Auto" tab will serve as additional function of the "Mirror" and
"VGA1" respectively by removing the check mark under the "Display
Combination" selection field.
78
Page 81
• Select the "VGA1" if you want the picture to only display on the monitor
screen.
• Select "LCD2" if you want the picture to only display on the notebook
computer screen.
Use the [Fn] + [F12] hot keys to toggle between the
LCD and external monitor display. If you prefer to
use only one display in operating your system, press
the [Fn] + [F12] hot keys will shut down the LCD
display, external monitor display or both at this
random order.
Single
This function will only show one single display whether it be on your notebook computer
or external monitor.
Mirror (Simultaneous Display)
This function supports two asynchronous simultaneous display paths with the features of
LCD, LCD/CRT or CRT).
1. Click on the “Control Panel” and double click on the “Display” icon. Click
on the “Settings” tab to enter the “Display Properties” window. Click on the
“Advanced” button.
2. From the “SiS 651 Properties” window, click on the “Display Modes” tab.
Select the "VGA1" or "LCD2" tab by clicking on the button to enable and
connect the video display to the external CRT screen.
3. Click on the “Apply” tab and you will be ask to keep the new setting. The
notebook computer and external monitor/TV screen will now simultaneously
display the same image.
79
Page 82
Multi-Monitor
"Multi-Monitor" is only applicable when the function of "Dual View" is being access.
This function will only be available if an external monitor is connected to your notebook
computer.
Use this to achieve a large desktop display on a small size screen. To do this:
• Adjust the screen resolution by increasing the desktop area in the “Display Area”.
• Use your touch pad or mouse cursor to point at any area of the screen to move the
window screen to a larger view.
To achieve the “Dual View” function, follow the procedures below:
1. Click on the “Control Panel” and double click on the “Display” icon.
2. Click on the “Settings” tab to enter the “Display Properties” window.
3. Use the cursor to click on the Monitor “2” screen on the sub-screen of the
“Display Properties” window.
4. A message is shown on your screen to ask you whether to enable the monitor
that you have chosen.
5. Click “Yes” to accept the change. Click the “Apply” tab to run the function
and restart the computer.
6. After the system has restarted, your notebook computer LCD screen and the
external monitor screen are connected with each other. From the LCD
display, open the “Display Properties” and use the cursor to drag it to the
right thus moving the image to the external monitor screen.
80
Page 83
Video Setting
From the "Setting", you can also adjust the video of your display to overlay, contrast or
brightness.
81
Page 84
Gamma Correction
You can adjust the right color for your window screen by moving the “Brightness”
adjustment window to increase or decrease the right resolution for your screen display.
82
Page 85
Troubleshooting
8
83
Page 86
This chapter describes locating and solving problems that you may encounter while using
your computer.
Locating a Problem
Problems with your computer can be caused by something as minor as an unplugged power
cord – or as major as a damaged hard disk. The information in this chapter is designed to
help you find and solve minor problems. If you try all the suggested solutions and you still
have a problem, make a list of what steps you have taken to correct the problem and contact
your dealer.
Successful troubleshooting is the result of careful observation, deductive reasoning, and an
organized approach to solving the problem.
The problems that you will encounter can be divided into two basic categories: hardware
problems and software problems. Hardware problems can be further divided into electrical
and mechanical problems. You will know you have a hardware problem if the screen is dark,
the computer cannot read the disk drives, or you get an error message during the Power-On
Self Test (POST).
Software errors can occur at several levels. The ROM BIOS and the operating system can
give you a large number of error messages. On top of this, each application software
package has its own set of error messages. It is important to determine whether the software
error message you are getting is from the application or the operating system. Once you
know this, you can look in the respective manual for a solution to the problem.
Checking Cables and Connections
Start by performing a careful visual inspection of the exterior of the computer. If no LEDs
are illuminated, make sure that your computer and its peripherals are getting power and
communicating with each other properly.
To check the power cables, and connections:
1. If you have been using battery power, connect the Notebook to an external power
84
Page 87
source and make sure that the battery has a charge.
2.
3.
4.
If you are using the Notebook with the AC adapter, check the power outlet, the
power cord, and any power switches that may affect your computer.
• Check the wall outlet or power strip with an item that you know is functioning
properly. A lamp or radio is
• a convenient item for checking the power. You may also need to check the fuses
and breakers in your electric box.
• If the outlet is controlled by a wall switch, make sure that the switch is on.
• If the outlet is controlled by a dimmer switch, use a different outlet.
• If your computer is plugged into a power strip with an On/Off switch, make sure
the switch is on.
With the computer’s power switched off, check all cable connections. If the
computer is connected to any peripheral devices, look for loose or disconnected
cables.
• If the computer is too close to a wall, a cable connection may be loose or the
cables may be crimped.
• Do not substitute cables for different devices (other than the manufacturer
recommended cables) even if they look exactly alike. The wiring inside the cable
may be different.
When you are certain that you have power available and all connections are good,
turn the computer on again. If the computer still does not start, you may have a
hardware problem.
The Power-On Self Test
The Power-On Self Test (POST) runs every time you turn on or reset the Notebook. The
POST checks memory, the main system board, the display, the keyboard, the disk drives, and
other installed options.
85
Page 88
A few seconds after you turn on your computer, a copyright message appears on your display
screen. A memory test message appears next; as the test continues, memory size increases
until all installed memory is tested. Normally, the only test routine visible on the screen will
be the memory test.
Two classifications of malfunctions can be detected during the POST:
• Error messages that indicate a failure with either the hardware, the software, or the Basic
Input/Output System (BIOS). These critical malfunctions prevent the computer from
operating at all or could cause incorrect and apparent results. An example of a critical
error is microprocessor malfunction.
• Messages that furnish important information on the power-on and boot processes (such as
memory status). These non-critical malfunctions are those that cause incorrect results that
may not be readily apparent. An example of a non-critical error would be a memory chip
failure.
In general, if the POST detects a system board failure (a critical error), the computer halts
and generates a series of beeps. If failure is detected in an area other than the system board
(such as the display, keyboard, or an adapter card) an error message is displayed on the
screen and testing is stopped. It is important to remember that the POST does not test all
areas of the computer, only those that allow it to be operational enough to run diagnostic
programs.
If your system does not successfully complete the POST, but displays a blank screen, emits a
series of beeps, or displays an error code, consult your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented in the table below:
Problem:
Solution:
The capacity of the battery is between 95 to 99% but can not fully
charged.
Please discharged to less than 95% of its capacity then recharge the
battery.
86
Page 89
Problem: Failure in the installation of the Audio driver.
Solution:
Problem:
Solution:
Problem:
Solution:
Problem:
Solution:
Problem:
Solution:
Problem:
Solution:
Be sure to first remove the current audio device from your system.
Please follow the instruction on the installation of audio driver.
The display screen is dark
Make sure that the computer is not in Suspend mode. Check the
Brightness controls for the screen. If the controls are turned too far
down, the screen will be dark.
An incorrect date and time are displayed.
Correct the date and time using the DOS DATE and TIME commands
or the options in the Setup Utility. If the date and time become incorrect
after a short time, your CMOS battery may be depleted. Contact your
dealer to change the battery.
The message: “Invalid system disk, Replace the disk, and then
press any key” appears during boot.
Check and make sure that you do not have a non-bootable floppy
diskette inserted in your floppy drive. If your USB FDD is empty, you
may not have an operating system installed on your drive. Contact
technical support for assistance.
You hear irregular beeps during operation of the Notebook and the
system halts.
The problem is beyond the scope of this manual. Contact technical
support.
An unidentified message is displayed.
Reboot the computer and run the BIOS system setup. Confirm the
Setup parameters. If the same message is displayed after booting up
again, contact technical support for assistance.
87
Page 90
Problem: The system cannot access the DVD-ROM drive.
Solution:
Problem:
Solution:
Problem:
Solution:
Problem:
Solution:
Problem:
Solution:
Problem:
Solution:
Check that a CD is properly inserted in the drive. Make sure that you
are using the correct program for that kind of CD. For example, the
system cannot read a data CD using an audio program.
You cannot operate the printer.
Check the printer cable connection. Ensure that the printer power
switch is turned on. Confirm that the printer is on-line.
You can’t save data to disk.
Ensure that the disk has been formatted.
Consult your operating system manual for information on formatting
floppy diskettes.
The diskette is write-protected.
Eject the diskette, remove the write protection, and try again.
The diskette if full.
Try using another diskette or free up some space on the diskette. The
disk drive is not operating. Contact your dealer for support.
You cannot use the mouse.
Check the cable connection.
Check the mouse with another application to see if there is a software
incompatibility problem.
If possible, check the mouse with another computer to see if it works. If
it doesn’t operate on a different system, the mouse might be broken.
88
Page 91
Contacting Your Dealer
If you still have a problem after reading the preceding sections, the next step is to contact
your dealer. Your dealer can determine if the problem is something that requires the
computer to be taken to the shop. Before you call your dealer, however, prepare the
following information:
• How is your computer configured? Your dealer needs to know what peripheral devices
you are using.
• What messages, if any, are on the screen?
• What software were you running at the time?
• What have you done already to try to solve the problem? If you have overlooked a step,
your dealer may be able to solve the problem over the phone.
89
Page 92
90
Page 93
How do I expand
my Notebook
9
91
Page 94
Upgrading your Memory
Refer to the following instructions and illustration for information on upgrading your
notebook's memory.
1.
2.
Turn off the computer and disconnect the AC adapter and all peripherals.
Open your computer and locate on the 4 grip of the keyboard attaching to the slot.
3. Use any card to release the keyboard by inserting on the 4 grip attaching the
keyboard.
92
Page 95
4. Turn over the keyboard and locate for the RAM module compartment.
5. Remove the screws that secure the RAM module compartment cover and set it aside
in a safe place.
93
Page 96
6. Remove the compartment cover and then angling it up and out.
7.
8.
9.
10.
11.
12.
If you need to install a higher capacity module, gently push the edge clips on both
sides to release the module. Angle the card slightly upward and gently slide it from
its edge connector slot. Store the card in the anti-static bag that contains your new
module(s).
To install the new memory card, hold the card with its gold edge connector toward
the edge connector slot of the compartment. To help you orient the cards, the edge
connector has been made with two unequal-length sections. You will only be able
to insert the card in one direction.
Insert the edge connector into the slot. The gold edge connector of the card should
not be visible when the card is fully inserted.
Press the card downward where you should hear an audible click as the latches of
the connector secure the card in place.
Once the module is properly seated, you can replace the cover on this compartment.
Replace and tighten the screw.
94
Page 97
Easy to Upgrade HDD Module
The hard drive in your notebook computer is made to be easily swapped out for upgrading.
You should back up your hard drive before attempting o change the hard drive.
Make sure that before you install a new drive, all the files in your system should be backed
up.
How to upgrade your Hard Drive
1.
2.
3.
4.
5.
Power down the system completely. Turn the system over with the front of the unit
facing you.
Remove the two screws that secure the compartment cover and set them in a safe
place.
Slide the HDD cover away from the compartment.
The drive is attached to a special bracket that secures it to the notebook computer.
There are 2 screws that hold the bracket.
Push the HDD slightly in the direction of the arrow as shown in the illustration to
release it from the pins of the drive.
95
Page 98
6. Gently hold the grip of the HDD, lift it up to release from its compartment.
7.
8.
9.
To install the new HDD, you will need to align the tabs on the drive bracket with
the slots on the bay. Press down gently on the drive bracket until it engages with
the system. Do not force the drive into place this can bend the pins on the hard
drive.
Slide the compartment cover into place and be sure the screw holes on the cover
align completely with the screw holes in the case.
Secure the cover with the two screws.
CPU Upgrade
To upgrade your CPU, follow the procedures below:
1.
2.
Turn the notebook over so that the rear ports are facing you.
Locate for the expansion compartment.
96
Page 99
3.
4.
5.
Unscrew and remove the cover of the CPU compartment.
Remove all the screws attached to the heatsink.
Before removing the screws, there are certain measures to followed in removing the
heatsink.
97
Page 100
6. To remove the heatsink, first loosen the screw carefully.
7. After loosening one screw, be certain that the next to be loosen should be the screw
on its adjacent side as shown on the illustration.
Be sure to loosen all the screws first before removing it
totally to release the heatsink. Failure to do so will cause a
major damage to the heatsink.
8. Now you can totally remove all the screws also in that order when you first loosen
the screw.
Removing the DVD-ROM/Combo Drive
1. Remove the screws and push the drive into the direction of the arrow as described
in the illustration.
2. Pull out the DVD-ROM drive from the bay.
98
Loading...