Page 1
Notice
The company reserves the right to make any updating, revisions or
changes to the information contained herein as and when deemed
necessary. The company is under no obligation to notify any purchaser or
end-user of such actions in advance or afterwards.
1998
User’s Manual
Page 2
Trademarks
IBM PC, OS/2, PS/2, EGA, and VGA are registered trademarks of
International Business Machines Corporation.
Intel, Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft Windows, Windows NT and Microsoft Mouse are
registered trademarks of Microsoft Corporation.
Sound Blaster Pro is a trademark of Creative Labs, Inc.
SystemSoft is a registered trademark of SystemSoft Corp.
Other brand and product names are trademarks of their respective
companies.
User’s Manual
Page 3
Warranty Provisions
Keep the product’s bar code legible to protect your right for warranty
services.
The manufacturer warrants this personal computer to be in working order
for a period of one year from the date of shipment. If this product fails
within the one year warranty period the manufacturer will, at its option,
repair or replace the product at no charge except as set forth below.
Warranty service will be furnished on an exchange basis. The
manufacturer may repair or replace your product with a new or
reconditioned one. Any replaced components or parts become the
property of the manufacturer.
No warranty is expressed or implied for products damaged by accident,
abuse, misuse, acts of god, or un-authorized modification. No warranties
apply after the one year warranty period.
To obtain warranty service described herein, deliver the product along with
proof of purchase date, to any of the manufacturer’s authorized distributors
during the warranty period. The owner agrees to insure the product and
assume the risk of damage or loss in transit, to pay in advance all shipping
charges, and to use the original shipping container (or the equivalent).
The manufacturer is not liable to any purchaser or end-user for any
damages including, but not limited to, lost revenue, lost wages, lost savings,
or any other incidental or consequential damages arising from the
purchase, use, or inability
to use this product.
User’s Manual
Page 4
Safety Notice
The computer is a delicate device that requires careful handling.
Negligence or mistaken use may cause serious damage. Before you learn
to operate or use this computer, you need to understand the instruction
regarding safety handling.
The following mentions the incorrect handling that is seriously inhibited.
To keep the computer from being damaged, please keep these precautions
in your mind.
Do not turn off power in operation.
Do not turn off the peripheral
device when the light is on.
Do not place the computer on unstable
surface.
Do not touch the poisonous liquid
when the LCD panel is broken.
User’s Manual
Page 5
Do not disassemble the computer
yourself.
Do not touch power cord by wet
hand.
Do not place anything heavy on the
computer.
Do not use broken power cord.
Keep the computer away from any
metal appliance.
User’s Manual
Do not throw the computer or
accessories into fire.
Page 6
The following mentions the actions that are important for your computer.
To keep your computer in the most excellent condition, please follow the
instruction as much as possible.
If there is unusual odor, heat or
smoke, plug out the power cord.
Plug out the power cord in
attaching peripheral devices.
Follow the use instruction in taking
airplane.
User’s Manual
Use the same brand of peripheral
devices.
Page 7
Maintain your computer regularly. Do not place heavy thing on the
power cord.
Affix tape to the contact plate while
putting the battery into keeping
box.
The data is easy to lose in low
power status.
Take a rest after a long term of
work.
Please keep the computer away
from humid environment.
User’s Manual
Page 8
Conventions
This manual uses the following conventions to describe, identify, and
highlight terms and operating procedures.
Text Conventions
Text in boldface contains messages that are important for safe operation.
Please read.
Characters in boldface represent specific items or keys, e.g. CardBus, Fn
key.
File names are presented in bold capitals, e.g. A:\>0VMAKFIL /Pn.
Abbreviations
For the purpose of clarity, abbreviations are enclosed in parentheses
following their definition; for example, Enhanced Parallel Port (EPP) mode.
Icons
Icons identify ports and jacks of the notebook computer. The system
status indicators are also identified with their relative icons.
Keys
Keys appear in boldface. A plus sign (+) between two keys indicates that
they should be pressed simultaneously.
Messages
Note: A note is an advice that helps you to make the best
use of the computer. Please read it.
Caution: A caution is a reminding that reminds you
something important for your computer. Please keep it in
your mind.
User’s Manual
Page 9
Ergonomics
Developing good work habits are important if you need to work in front of
the computer for long periods of time. Improper work habits can result in
discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
Adjust the height of the chair and/or desk so that the keyboard is
at or slightly below the level of your elbow. Keep your forearms,
wrists, and hands in a relaxed position.
Your knees should be slightly higher than your hips. Place your
feet flat on the floor or on a footrest if necessary.
Use a chair with a back and adjust it to support your lower back
comfortably.
Sit straight so that your knees, hips and elbows form
approximately 90° angles when you are working.
User’s Manual
Page 10
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain
and muscle fatigue in your neck and shoulders.
Position the display to avoid glare or reflections from overhead lighting
or outside sources of light.
Keep the display screen clean and set the brightness and contrast to
levels that allow you to see the screen clearly.
Position the display directly in front of you at a comfortable viewing
distance.
Adjust the display viewing angle to find the best position.
In addition, continuous concentration on computing work can result in
discomfort and injury. Remember to:
Alter your posture frequently.
Stretch and exercise your body several times a day.
Take periodic breaks when you work at the computer for long periods of
time. Frequent and short breaks are of greater benefit than fewer and
longer breaks.
User’s Manual
Page 11
Table of Contents
Chapter 1 : Getting Started 1-1
Unpacking ..................................................................................... 1-2
Operating Environment ................................................................. 1-3
Powering the System .................................................................... 1-4
AC Power Adapter .................................................................... 1-4
Battery Pack ............................................................................. 1-5
Opening the LCD Cover ............................................................... 1-7
LED Indicators on the LCD Cover ............................................ 1-8
Top-Front View .............................................................................. 1-9
LCD Panel ................................................................................ 1-9
Stereo Speakers ....................................................................... 1-9
Trackpad and Buttons .............................................................. 1-9
Keyboard .................................................................................. 1-9
Microphone ............................................................................... 1-9
System Status LED Indicators ................................................ 1-10
Power Button .......................................................................... 1-10
Rear View ................................................................................... 1-12
Right-Side View .......................................................................... 1-14
Left-Side View ............................................................................. 1-16
5.25” CD-ROM Drive .............................................................. 1-16
Infrared ................................................................................... 1-16
Left-side Stand ........................................................................ 1-16
Chapter 2 : Operation 2-1
Upgrading Processor Module ....................................................... 2-2
Replacing Processor Module ................................................... 2-3
Setting DIP Switch ........................................................................ 2-4
Accessing DIP Switch (SW1) ................................................... 2-4
Expanding Memory ....................................................................... 2-6
Accessing the Memory Sockets ............................................... 2-7
Installing Memory Module ........................................................ 2-8
Removing Memory Module ...................................................... 2-9
Using Hard Disk Drive ................................................................ 2-10
Removing ............................................................................... 2-10
Replacing Hard Disk Drive ..................................................... 2-11
Using Floppy Disk Drive ............................................................. 2-12
Inserting/Removing Diskettes ................................................. 2-12
User’s Manual
Page 12
Replacing Floppy Disk Drive .................................................. 2-13
Using CD-ROM ........................................................................... 2-14
Removing CD-ROM Module ................................................... 2-15
Loading Compact Discs ......................................................... 2-16
Handling of Compact Discs .................................................... 2-17
Using PC Card Sockets .............................................................. 2-18
Inserting PC Cards ................................................................. 2-19
Removing PC Cards ............................................................... 2-19
Using Hot Keys ........................................................................... 2-20
Windows 95 Special Keys ...................................................... 2-21
Using Numeric Keypad ............................................................... 2-22
Using Power Management ......................................................... 2-23
Advanced Power Management (APM 1.2) ............................. 2-23
Advanced Configuration and Power Interface (ACPI) ............ 2-23
Global Standby ....................................................................... 2-23
Hard Disk Standby .................................................................. 2-23
Suspend and Resume ............................................................ 2-24
Attaching Peripheral Devices ...................................................... 2-26
Attaching a Security Lock ....................................................... 2-26
Attaching a Parallel Printer ..................................................... 2-27
Attaching a TV Set .................................................................. 2-28
Attaching a Video Input Device .............................................. 2-29
Attaching a USB-compatible Device ...................................... 2-30
Attaching a Serial Mouse ....................................................... 2-31
Attaching an External Monitor (CRT) ..................................... 2-32
Attaching a PS/2 Keyboard or Mouse .................................... 2-33
Attaching a Digital Camera ..................................................... 2-34
Chapter 3 : BIOS Utilities 3-1
Power on Self Test (POST)........................................................... 3-2
POST Message: Normal Operation .......................................... 3-2
POST Message: Error Detected ............................................... 3-3
System Configuration Utility ......................................................... 3-4
Information in the System Configuration Utility ........................ 3-4
Initiating the System Configuration Utility ................................. 3-5
Working with the Menu Bar ...................................................... 3-6
Working with the Pull-down Menu ............................................ 3-7
Features of the System Configuration Utility ............................ 3-8
Chapter 4 : Troubleshooting 4-1
Battery........................................................................................... 4-2
Power ............................................................................................ 4-3
User’s Manual
Page 13
Hard Disk Drive ............................................................................. 4-3
Floppy Disk Drive .......................................................................... 4-4
Hardware Installation .................................................................... 4-4
LCD Panel .................................................................................... 4-5
Memory Module ............................................................................ 4-6
PC Card ........................................................................................ 4-6
Boot Password .............................................................................. 4-7
Audio ............................................................................................. 4-7
CD ................................................................................................. 4-8
Printer ........................................................................................... 4-9
Chapter 5 : Installing Drivers 5-1
Installing Windows 95 ................................................................... 5-2
Installing Windows 98 ................................................................... 5-4
Installing Drivers in Windows 95 ................................................... 5-5
Step 1: Installing USB Driver .................................................... 5-5
Step 2: Installing TXPATCH Driver ........................................... 5-5
Step 3: Installing VGA Driver .................................................... 5-5
Step 4: Installing Audio Driver (1978S M2E) ............................ 5-6
Step 5: Installing PCMCIA driver .............................................. 5-6
Step 6: Installing Video-in Driver .............................................. 5-7
Step 7: Installing ATI DVD Play Driver ...................................... 5-7
Installing Drivers in Windows NT 4.0 ............................................ 5-8
Step 1: Installing VGA Driver .................................................... 5-8
Step 2: Installing Audio Driver (1978S M2E) ............................ 5-8
Installing Drivers in Windows 98 ................................................... 5-9
Step 1: Installing VGA Driver .................................................... 5-9
Step 2: Installing Audio Driver (1978S M2E) ............................ 5-9
Step 3: Installing PCMCIA Driver ............................................ 5-10
Step 4: Installing Video-in Driver ............................................ 5-10
Appendix A: Specifications 1
Appendix B: I/0 Port Pin Assignments 1
Index 1
User’s Manual
Page 14
User’s Manual
Page 15
Chapter 1: Getting Started 1-1
’s Manual
Chapter 1 : Getting Started
This chapter provides you with the short instruction of notebook computer
system that will help you to get the basic understanding about the
computer.
Unpacking
Operating Environment
Powering the System
AC Power Adapter
Battery Pack
Opening the LCD Cover
Top-Front View
Rear View
Right-side View
Left-side View
User
Page 16
Chapter 1: Getting Started 1-2
’s Manual
Figure 1
-1
Unpacking
Carefully unpack the notebook computer and the included accessories
(Figure 1-1). Check the items one by one. If there is something wrong,
contact your dealer immediately.
Notebook Computer.
Carrying Bag.
Power Adapter.
Power Cord.
User Manual.
PS/2 Transfer Cable.
Battery Pack.
Utilities Diskette(s)
.
User
Page 17
Chapter 1: Getting Started 1-3
’s Manual
Operating Environment
As with any other precision electronic equipment, proper care and
operation of your computer will prolong the use period. Make sure the
computer is not:
Exposed to excessively heat or direct sunlight.
Shocked or vibrated.
Exposed to strong magnetic fields.
Left in a place where foreign matter or moisture may affect the
system.
Figure 1-2
User
Page 18
Chapter 1: Getting Started 1-4
’s Manual
Figure 1
-3
Powering the System
You can use the AC power adapter or battery pack to power the computer
system.
AC Power Adapter
Use only the power adapter that comes with your computer. An incorrect
type of power adapter will cause damage to the computer and its
components.
1.
Plug the power adapter cord into the AC-in socket on the rear panel of
the computer.
2.
Connect the power adapter with the power cord.
3.
Plug the power cord into a properly grounded outlet (Figure 1-3).
4.
Refer to Chapter 1, System Status LED Indicators for more information
on system power status.
User
Page 19
Chapter 1: Getting Started 1-5
’s Manual
Battery Pack
The battery pack provides power for continuous portable operation of the
computer. When using the battery no external power source is required.
The actual operation time is related to the application and the
configuration you’re using.
Inserting
1.
Turn the computer over.
2.
Fit the battery pack firmly at a slight angle into the computer.
3.
Install the four screws to fasten the battery pack (Figure 1-4).
Removing
1.
Turn the computer over.
2.
Remove the four screws that fasten the battery pack.
3.
Carefully lift the battery pack from the computer.
User
Figure 1-4
Page 20
Chapter 1: Getting Started 1-6
’s Manual
Recharging by AC Power
The battery pack can be recharged when the computer is connected with
the AC power supply, no matter the system is in operation or not.
•
Connect the computer with the AC power supply to begin recharging
the system’s battery pack. You do not need to turn off the system’s
power.
•
Hours may be needed to recharge the battery pack.
•
Please refer to Chapter 1, System Status LED Indicators for more
information on battery charge status.
Proper Handling of the Battery Pack
•
Do not attempt to disassemble the battery under any circumstances.
•
The battery may explode if exposed to fire or high temperatures.
•
Avoid battery short circuit by preventing contact from the metal
terminals (+, -).
User
Page 21
Chapter 1: Getting Started 1-7
’s Manual
Opening the LCD Cover
1.
Move the latch to the right to release the top cover. (Figure 1-5).
2.
Lift the top cover to reveal the LCD panel and keyboard (Figure 1-6).
3.
Adjust the LCD panel to a comfortable viewing angle.
4.
Press the power button to turn the system on or off (refer to Chapter 1,
Top-Front View for more information of the power button).
Figure 1-5
User
Figure 1-6
Page 22
Chapter 1: Getting Started 1-8
’s Manual
Battery power is used with system turning
LED Indicators on the LCD Cover
Icon Color Description
Green
on.
Red AC power is used with system turning
on.
Green Battery is fully charged.
Red Battery is being charged.
Blinking Red Battery power is critically low.
User
Figure 1-7
Page 23
Chapter 1: Getting Started 1-9
’s Manual
Top-Front View
LCD Panel
The computer provides you with a large LCD panel. Depending on
the model you have purchased, it can either be a 15.1” or 15.0” TFT
flat panel The LCD panel is driven by a AGP bus video controller
with 8 MB video memory.
Stereo Speakers
Two built-in speakers provide clear stereo sound.
Trackpad and Buttons
The pointing device features a sensitive glide pad for precise
movements. It functions like a two-button mouse does. The right
trackpad button is equivalent to the right mouse button; the left
trackpad button is equivalent to the left mouse button.
Keyboard
The computer features a 102-key Windows 95 keyboard that is
integrated with the numeric keypad. It is detachable for various
language versions. You may refer to Chapter 2: Operation for more
information.
Microphone
This is the built-in microphone.
User
Page 24
Chapter 1: Getting Started
’s Manual
1-10
System Status LED Indicators
The LED indicators display the system’s operation status.
Icon Color Description
Green Battery power is used with system turned
on.
Red AC power is used with system turned on.
Green Battery is fully charged.
Red Battery is being charged.
Blinking Red Battery power is critically low.
Green The system has entered the configured
suspend mode (either POS or STR mode).
Green The hard disk is being accessed.
Power Button
Use this button to turn the system on or off.
Note: After turning off the system, wait for a few seconds to power it on
again.
After proper configuration under SCU, this button can be
used as suspend/resume hot button (refer to Chapter 3:
BIOS Utilities, Power Menu for more information).
User
Page 25
Chapter 1: Getting Started
’s Manual
Keyboard
Trackpad and Buttons
Status LED Indicators
1-11
Microphone
LCD Panel
Stereo Speakers
Power Button
Figure 1-8
User
Page 26
Chapter 1: Getting Started
’s Manual
1-12
Rear View
AC-in Socket
Plug the AC adapter into this socket for power supply. To
disconnect, pull the plug (not the cord) directly back.
Security Connector
The Security Connector is used to protect your computer from
being stolen. Wrap the steel cable around your desk. Then,
insert the locking device into this security connector.
Parallel Port
This parallel port supports EPP (Enhanced Parallel Port) and
ECP (Extended Capabilities Port) modes.
S-Video Jack
Use this jack to transmit video signal to a TV set. You may
need to select the video standard (NTSC/PAL) for video display
(please refer to Chapter 3, Components Menu for more
information).
RCA Jack
This jack accepts analog composite signals from external video
devices, e.g. camera, CD.
Expansion Port
This port is used to connect the proprietary Port Replicator.
Dual USB Ports
The dual Universal Serial Bus (USB) ports simplify the
expansion capability for peripheral devices.
Serial Port
This port is UART 16C550 compatible. It features a 9-pin
connector for the addition of an external mouse for example.
User
Page 27
Chapter 1: Getting Started
’s Manual
USB Ports
S-
Video Jack
CRT Port
Parallel Port
RCA JacK
Serial Port
1394 Port
1-13
External Monitor (CRT) Port
This port is used for transmission of the display to an external
monitor. Simultaneous display with the LCD panel is available.
Dual PS/2 Type Ports
A PS/2 type mouse and keyboard can be connected to the
system using these ports. However, you cannot connect the
same type of PS/2 devices to both ports simultaneously.
1394 Port
A newly developed port which connects with the digital camera.
Figure 1-9
AC-in socket
User
Security connector
Figure 1-10
PS/2 type ports Expansion port
Page 28
Chapter 1: Getting Started
’s Manual
1-14
Right-Side View
PC Card Sockets
One Type III or two Type II PC cards can be used. Both
sockets will expand the system capabilities when a PC card is
inserted. To eject the PC card, press the appropriate eject
button (Figure 2-15).
2.5” Hard Disk Drive
The 2.5” hard disk drive is removable. It accepts any 2.5”
IDE hard disk drive with a height of 12.7mm or less. Refer
to Chapter 2: “Operation” for more information.
3.5” Floppy Disk Drive
The computer comes standard with a 1.44MB floppy drive
installed. Press the button on its top-right side to eject the
diskette. The floppy disk module can be replaced with
additional drive units, such as a secondary 2.5”/3.0” hard disk
drive or Zip drive (Refer to Chapter 2: Operation for more
information).
Speaker-out Jack
Headphone and speakers can be attached to the system
through this jack.
Line-in Jack
External audio source can be fed into the computer through
this jack.
Microphone-in Jack
Use this jack to connect a microphone to the system.
User
Page 29
Chapter 1: Getting Started
’s Manual
Ventilation
Microphone
-in
Line-in
Speaker
-
out
3.5” Floppy Disk Drive
PC Card Socket
2.5” Hard Disk Drive
Right
-
side stand
1-15
Ventilation
The computer provides ventilation to dissipate the system’s
operation heat. Do not block or obstruct it during operation.
Right-side Stand
Move this stand (together with the left one) to adjust the typing
angle. If a high speed CPU is installed, erecting the stands on
both sides will be necessary for heat dissipation during operation
(Figure 1-12).
Figure 1-12
User
Page 30
Chapter 1: Getting Started
’s Manual
1-16
Left-Side View
5.25” CD-ROM Drive
The 5.25” IDE CD-ROM module is designed to be removable. The
eject button is located in the middle of the front cover of the CD-ROM
drive. Pressing it will release the CD tray.
Infrared
The system adopts infrared technology as the interface for simple,
fast and convenient data exchange from the computer to an
infrared-compatible device. It implements IrDA (HPSIR), Amplitude
Shifted Keyed IR (ASKIR), and Fast IR (FIR). No object should be
blocking the line of sight between the computer and the
infrared-equipped device. For further information, please refer to
the manual of the wireless device you wish to connect on how to use
the point-and-shoot operation.
Left-side Stand
Move this stand (together with the right one) to adjust the typing
angle. If a high speed CPU is installed on the system, erecting the
stands on both sides will be necessary for heat dissipation during
operation (Figure 1-14).
User
Page 31
Chapter 1: Getting Started
’s Manual
CD-ROM Drive
Infrared
Left-side Stand
1-17
Figure 1-13
Figure 1-14
User
Page 32
Chapter 1: Getting Started
’s Manual
1-18
User
Page 33
Chapter 2: Operation 2-1
’s Manual
Chapter 2 : Operation
The notebook computer has many advanced features to help you with your
computer work. This chapter describes each of the computer’s hardware
features and shows you how to use them.
Before you begin working with the internal components of the computer,
remove the battery and disconnect the AC power adapter.
Make sure you wear an anti-static wrist strap to ground yourself before
working with or repair the internal components. Static electricity may
damage the components.
Upgrading Processor Module
Setting DIP Switch
Expanding Memory
Using Hard Disk Drive
Using Floppy Disk Drive
Using CD-ROM
Using PC Card Sockets
Using Hot Keys
Using Numeric Keypad
Using Power Management
Attaching Peripheral Devices
User
Page 34
Chapter 2: Operation 2-2
’s Manual
Upgrading Processor Module
The notebook computer features the structure of Intel’s Mobile Module
(MMC2). The Processor Module incorporates an Intel Pentium Mobile
processor, secondary cache, and the Intel PCIset “Northbridge” system
controller, voltage regulator, and thermal sensor on a single printed circuit
board.
The Processor Module is connected to the mainboard through a connector.
This design facilitates users to easily upgrade their system by simply
replacing the Processor Module.
View from Top
Connector
User
View from Bottom
Figure 2-1
Page 35
Chapter 2: Operation 2-3
’s Manual
Replacing Processor Module
1.
Remove all power sources (AC power and battery).
2.
Turn the computer over.
3.
Remove the CPU cover.
4.
Remove the screws that fasten the heat sink mounted on the
Processor Module.
5.
Carefully detach the Processor Module from the mainboard (Figure
2-2).
CPU Cover
Heat Sink and Fan
Processor Module
User
Figure 2-2
Page 36
Chapter 2: Operation 2-4
’s Manual
DIP Switch (SW1)
Purpose
SW1
-1
SW1
-2
Flash ROM BIOS
Setting DIP Switch
Remove the keyboard to reveal the system’s mainboard. Locate the DIP
Switch (SW1) to set the correct configuration for the following purpose:
Flash ROM BIOS update
To upgrade your computer, you need to keep up with the latest system
BIOS. Consult your dealer for further information. The DIP Switch needs
to be set in the On position when updating the existing system BIOS. The
DIP Switches should be reset to the Off position after BIOS updating is
complete.
Off Off Existing BIOS
On On Updating BIOS
Accessing DIP Switch (SW1)
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its normal
position (Figure 2-3).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the DIP Switch SW1 to set the configuration (Figure 2-4).
User
Page 37
Chapter 2: Operation 2-5
’s Manual
Figure 2-3
SW1
Figure 2-4
User
Page 38
Chapter 2: Operation 2-6
’s Manual
Expanding Memory
The system has three memory sockets for different RAM modules to
expand the memory up to 384MB. The RAM modules should be 144-pin
SODIMM (Small Outline Dual In-line Memory Module) type. The computer
supports EDO, and SDRAM operation. The total memory size is
automatically detected by the POST routines. To expend the memory, you
have the following choice with different DRAM combinations:
Bank 0 Bank 1 Bank 2 Total Size
32 0 0 32
32 32 0 64
32 32 32 96
64 0 0 64
64 32 0 96
64 32 32 128
64 64 0 128
64 64 32 160
64 64 64 192
128 0 0 128
128 32 0 160
128 32 32 192
128 64 0 192
128 64 32 224
128 64 64 256
128 128 0 256
128 128 32 288
128 128 64 320
128 128 128 384
User
Page 39
Chapter 2: Operation 2-7
’s Manual
Non-component area
31.75mm
Figure 2
-
5.1
Bank 0
Bank 1
Bank 2
Accessing the Memory Sockets
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its
normal position (Figure 2-3).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the memory sockets (Figure 2-5).
Note:
The memory socket Bank 1 is a reverse type, make sure you
install the memory module with reverse side to fit its connector.
Please ensure that each edge of the memory module (SDRAM)
has no component mounted on (see Figure 2-5.1). It is
recommended to use the RAM module that complies with Intel
unbuffered SO-DIMM (67.6mmX31.75mm). Please consult your
dealer for detailed information.
67.6mm
Figure 2-5
(The edges of the memory module
are the non-component area.)
User
Page 40
Chapter 2: Operation 2-8
’s Manual
Installing Memory Module
Follow the steps below to install the memory module:
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its
normal position (Figure 2-3).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the memory sockets (Figure 2-5).
4.
Insert the memory module at a slight angle (45∘∘∘∘ ) and fit its
connectors into the socket firmly.
5.
Press two edges of the memory module (as the arrows indicated)
to make it locked into place (Figure 2-6).
6.
Reinstall the keyboard assembly.
Note:
Make sure you install the memory module in the order of Bank 0, Bank
1, Bank 2 (see Figure 2-5). Please refer to the table of DRAM
combinations or consult your dealer for a proper installation.
Figure 2-6
User
Page 41
Chapter 2: Operation 2-9
’s Manual
Figure 2
-7
Removing Memory Module
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its
normal position (Figure 2-3).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the memory sockets (Figure 2-5).
4.
Gently pull the two latches outward on both ends of the module. The
module will pop up (Figure 2-7).
5.
Remove the memory module.
6.
Reinstall the keyboard assembly.
User
Page 42
Chapter 2: Operation
’s Manual
2-10
Using Hard Disk Drive
The hard disk drive is mounted in a removable case and can be taken out
to accommodate other 2.5” IDE hard disk drives with a height of 12.7mm.
The system supports drives with 2.0 GB capacities through the Logical
Block Addressing (LBA) mode. It also supports Programmed I/O (PIO)
mode 4, Bus Master IDE and provides a high performance data transfer
rate at speeds up to 33 MBytes/second (ATA-33).
Removing
1.
Turn the system power off.
2.
Turn the computer over.
3.
Locate the Hard Disk Drive latch.
4.
Press the latch in the direction indicated and take the hard disk drive
out of the computer (Figure 2-8).
Figure 2-8
Note:
When inserting the hard disk drive, Insert it firmly into the computer. Make
sure you feel the drive click into the position when it is seated properly.
User
Page 43
Chapter 2: Operation 2-11
’s Manual
Replacing Hard Disk Drive
The hard disk drive is contained in a case. To take the hard disk drive out
of the case and replace with another one, you need to remove the two
screws on each side of the case (Figure 2-9). The location of the two
screws may be varied depending on different types of hard disk model.
Gently disconnect the cable from the hard disk drive when taking it out of
the case. Be careful not to bend any pins or crimp the cable.
Figure 2-9
User
Page 44
Chapter 2: Operation
’s Manual
2-12
Using Floppy Disk Drive
The notebook computer comes standard with a 1.44MB, 3.5” floppy disk
drive module. It is labeled drive A: and may be used as a boot device if
properly set.
You may replace the floppy disk module with the following options: a 2.5”
secondary hard disk drive (of 12.7mm or 17mm high), a 3.0” secondary
hard disk drive (of 12.5mm high), a 100MB Zip drive (of 15mm high), or a
LS-120 device (of 12.7mm high). Contact your dealer for details about
these options.
Inserting/Removing Diskettes
When using the floppy drive, always insert your floppy diskette label-side
up (Figure 2-10). To remove your diskette, press the eject button on the
top-right corner of the floppy drive.
Figure 2-10
User
Page 45
Chapter 2: Operation
’s Manual
2-13
Replacing Floppy Disk Drive
1.
Turn the system power off.
2.
Turn the computer over.
3.
Locate the Floppy Disk Drive latch.
4.
Press the latch in the direction indicated and take the floppy disk drive
out of the computer (Figure 2-11).
5.
Insert the replacement drive (2.5”/3.0” secondary HDD or 100MB Zip
drive) firmly into the computer.
Figure 2-11
User
Page 46
Chapter 2: Operation
’s Manual
2-14
Using CD-ROM
The notebook computer comes standard with a removable 5.25” CD-ROM
module. It is labeled drive D: and may be used as a boot device if
properly set.
To insert a CD, press the Eject Button and place the CD into the Disc
Tray with label-side facing up. Push the CD tray in and you are ready to
start. The Busy Indicator will light up while data is being accessed or
while an audio CD is playing. When the power is unexpectedly interrupted,
insert an instrument such as a straightened paper clip into the Emergency
Eject Hole to eject the tray (Figure 2-12).
Figure 2-12
Disc Tray
Eject Button
Busy Indicator
Emergency Eject
User
Page 47
Chapter 2: Operation
’s Manual
2-15
Removing CD-ROM Module
1.
Turn the system power off.
2.
Turn the computer over.
3.
Locate the CD-ROM latch.
4.
Press the latch in the direction indicated and take the CD-ROM
module out of the computer (Figure 2-13).
Figure 2-13
User
Page 48
Chapter 2: Operation
’s Manual
2-16
Loading Compact Discs
1.
Turn on the power.
2.
Press the CD-ROM eject button; the disc tray will pop out partially.
3.
Pull the disc tray out.
4.
Carefully load the CD into the disc tray with label-side facing up.
Press it gently to ensure it fits into the place (Figure 2-14).
5.
Push the tray into the computer.
Figure 2-14
User
Page 49
Chapter 2: Operation
’s Manual
2-17
Handling of Compact Discs
Proper handling of your CDs will prevent them from being damaged and
ensure the accessibility of data stored in them.
Hold the CD by the edges; do not touch the surface of the disc.
Use clean, soft, and dry cloth to remove dust or fingerprints.
Do not use pen to write on the surface.
Do not attach any paper or other materials to the surface of the disk.
Do not store or place the CD in the high-temperature areas.
Do not use benzine, thinners, or other cleaners to clean the CD.
Do not bend the compact disc.
Do not drop or subject the CDs to shock.
User
Page 50
Chapter 2: Operation
’s Manual
Socket B
Eject button for socket A
Socket A
Eject button for socket B
2-18
Using PC Card Sockets
The computer provides system expansion capabilities with two PC card
sockets (previously referred to as PCMCIA). PC cards to be inserted can
be LAN, fax/modem, communication devices, or expanded memory. Both
sockets support 5V/3.3V 16-bit PC cards and 3.3V 32-bit PC cards
(referred to as CardBus).
The PC card sockets on the right-side panel support one Type III card
(equivalent to two Type II cards). The lower socket (socket A) is capable
of ZV (Zoomed Video) (Figure 2-15).
Figure 2-15
Note: There are three types of PC cards. Type 1 measures 3.3 mm thick;
Type II 5.0 mm; and Type III 10.5 mm.
User
Page 51
Chapter 2: Operation
’s Manual
2-19
Inserting PC Cards
1. Open the access door (Figure 2-16).
2. Align the PC card with the slot and push it in firmly until it locks into the
place (Figure 2-17).
.
Figure 2-16
Figure 2-17
Removing PC Cards
To remove a PC card, press the appropriate eject button to eject the card
from its slot. (Figure 2-15).
User
Page 52
Chapter 2: Operation
’s Manual
Put the system in a suspend state for power
2-20
Using Hot Keys
Located on the bottom-left edge of the keyboard layout is a colored Fn key.
The Fn key function allows you to change operational features instantly.
When you use the following functions, press and hold the Fn key; then
press the appropriate function key (Figure 2-18).
Hot Keys System Features
Fn + F3
Fn + F6
Fn + F9
Fn + F10
Fn + F11
Fn + F12
Fn + Z
Fn + Esc
Expand LCD display.
Toggle CRT/LCD/LCD+CRT/TV/CRT+TV.
Decrease LCD brightness.
Increase LCD brightness.
Decrease audio volume.
Increase audio volume.
Turn audio mute on/off.
management.
User
Page 53
Chapter 2: Operation
’s Manual
2-21
Windows 95 Special Keys
The keyboard provides two keys that have special functions in Windows
95:
This key has the same functions as the secondary mouse does.
This key activates the Windows 95 Start menu.
Figure 2-18
User
Page 54
Chapter 2: Operation
’s Manual
2-22
Using Numeric Keypad
The computer features a 102-key keyboard with an integrated numeric
keypad for easy numeric data input (Figure 2-19).
Figure 2-19
User
Page 55
Chapter 2: Operation
’s Manual
2-23
Using Power Management
The system provides you with various modes to manage its power
consumption while maintaining system performance. Please refer to
Chapter 3: BIOS Utilities, System Configuration Utility, Power Menu for
more information.
Advanced Power Management (APM 1.2)
The system provides built-in Advanced Power Management (APM 1.2)
support to reduce power consumption. APM function varies depending on
the operation system you are using. Some operation systems do not
support APM, such as Windows NT, and therefore, cannot take
advantage of the system’s capabilities in this area.
Advanced Configuration and Power Interface
(ACPI)
The ACPI interface gives the operation system (OS) direct control over the
power management and Plug and Play functions of a computer. The
operation system can perform the functions covered by the ACPI
specification, such as system power management, device power
management, and thermal management.
Global Standby
In Global Standby mode, the CPU clock will be stopped and most
controllable peripheral devices will be power off. If the idle timer expires
before any system activity is detected, the system will change from Standby
mode into Suspend mode.
Hard Disk Standby
The system will turn off the computer’s hard disk drive motor if it has not
been accessed after a specified period of time. The motor will be turned
back on if the system attempts to read or write data to it.
User
Page 56
Chapter 2: Operation
’s Manual
2-24
Suspend and Resume
When at extremely low power, you can enter suspend mode to save power.
In suspend mode, all tasks are stopped and stored in memory to save
power. The system features two levels of suspend mode:
Powered-On-Suspend (POS) mode and Suspend-To-Disk (STD) mode.
Another useful feature is resume mode. This feature allows you to turn
the computer’s power off without exiting your software application. When
you turn the power on again, you can resume work where you left off,
because the screen display is restored as you left it. This saves time and
battery power.
Caution: Do not enter suspend mode when you are
1. Accessing any of the disk drives, such as HDD, FDD or CD-ROM drives.
2. Using the audio features or playing back video.
3. Playing a DOS game.
Powered On Suspend (POS)
Of the suspend modes, Powered-On-Suspend saves the least amount of
power. However, it takes the shortest time to return to full operation.
Resume from POS Mode
The system can resume from Powered-On-Suspend mode by:
Alarm resume (month/day/hour/minute)
Modem ring
Pressing any keyboard key.
Pressing the power button (if configured as Suspend/Resume function
under SCU)
Opening the display lid (only if the suspend mode is initiated by closing
the display lid)
User
Page 57
Chapter 2: Operation
’s Manual
2-25
Suspend To Disk (STD)
Suspend to Disk is a 0-volt suspend mode for system power management.
STD mode saves the maximum power but takes the longest time to return
to full operation.
1.
Use your operation system’s FDISK program to delete all partitions of
the hard disk if any already exist on the target drive.
2.
Boot the system and run the 0VMAKFIL.EXE Utility to create the
Suspend to Disk partition on the hard disk. The size of Suspend to Disk
partition will be the installed DRAM (n) plus 8MB integrated video RAM.
:\>0VMAKFIL –Pn
For example, if the system DRAM is 32MB, 0VMAKFIL will create a
partiton size of approximately 40MB.
:\>0VMAKFIL –P32
Resume from STD Mode
The system will resume from Suspend-To-Disk mode by:
•
Power back on
•
Alarm resume (month/day/hour/minute)
•
Opening the display lid (only if the suspend mode is initiated by
closing the display lid)
User
Page 58
Chapter 2: Operation
’s Manual
2-26
Attaching Peripheral Devices
To extend the computer’s functions, you can attach the following peripheral
devices to the computer through the ports or jacks on the rear panel of
computer.
Attaching a Security Lock
The security lock is equipped to protect your computer from being stolen.
To install the security lock, wrap the cable around a desk or other
immovable object, then insert the locking device into the connector (Figure
2-20).
Figure 2-20
User
Page 59
Chapter 2: Operation
’s Manual
2-27
Attaching a Parallel Printer
You may connect any standard Centronics parallel printer to your computer
through the parallel port.
1.
Turn the system power off.
2.
Connect the cable to the parallel port on the rear of the computer.
3.
Tighten the screws that fasten the cable to the parallel port (Figure
2-21).
4.
Insert the other end of the cable to the printer’s connector. Fasten
the cable’s connector.
5.
Turn on the printer and computer.
In addition, you also need to install the manufacturer-supplied driver for the
printer. Refer to the device’s user’s guide for more information. If the
connected printer supports EPP (Enhanced Parallel Port) or ECP
(Extended Capabilities Port) mode, please enter System Configuration
Utility (SCU) to configure the required setting.
Figure 2-21
User
Page 60
Chapter 2: Operation
’s Manual
2-28
Attaching a TV Set
The S-Video jack on the rear panel of the computer is used for transmitting
video signals to a TV set. You may need to select the video standard for
video display. Enter the System Configuration Utility (SCU), Components
Menu to specify the appropriate TV mode. Simultaneous display on
external monitor (CRT) and TV is available. You can enter the SCU to
select the appropriate parameters or use the Fn + F6 keys (refer to Chapter
2, Using Hot Keys).
Attach the TV set as shown below (Figure 2-22).
Figure 2-22
User
Page 61
Chapter 2: Operation
’s Manual
2-29
Attaching a Video Input Device
The RCA jack on the rear panel of the computer allows analog composite
signal input from external video devices. Attach the device as shown
below (Figure 2-23).
Figure 2-23
User
Page 62
Chapter 2: Operation
’s Manual
2-30
Attaching a USB-compatible Device
The computer provides dual USB ports for connection of a USB-compatible
keyboard, mouse, or other devices. Attach the device as shown below
(Figure 2-24).
Figure 2-24
User
Page 63
Chapter 2: Operation
’s Manual
2-31
Attaching a Serial Mouse
The serial port features a 9-pin connector. You can connect any serial
device such as a mouse to this port.
1.
Turn the system power off.
2.
Connect the cable to the serial port on the rear of the computer.
3.
Tighten the screws that fasten the cable to the serial port (Figure
2-25).
4.
Turn on the computer.
In addition, you may need to install the manufacturer-supplied driver for the
serial mouse. Refer to the device’s user’s guide for more information.
Figure 2-25
User
Page 64
Chapter 2: Operation
’s Manual
2-32
Attaching an External Monitor (CRT)
The computer is capable of displaying not only on the LCD, but also on the
XGA compatible displays attached to the computer. Information can be
displayed on both the LCD and the external monitor simultaneously. Enter
the System Configuration Utility (SCU) to select the appropriate parameters
or use the Fn + F6 keys (refer to Chapter 2, Using Hot Keys).
1.
Turn the system power off.
2.
Connect the cable to the CRT port on the rear of the computer.
3.
Tighten the screws that fasten the cable to the CRT port (Figure 2-26).
4.
Insert the other end of the cable to the external monitor.
5.
Turn on the computer.
Figure 2-26
User
Page 65
Chapter 2: Operation
’s Manual
2-33
Attaching a PS/2 Keyboard or Mouse
The computer can be operated with a PS/2 keyboard or mouse attached by
means of the PS/2 transfer cable. Attach the external keyboard or mouse
as shown below (Figure 2-27).
Both PS/2 type ports on the rear panel of the computer can be used for the
connection of a PS/2 keyboard and mouse.
Figure 2-27
User
Page 66
Chapter 2: Operation
’s Manual
2-34
Attaching a Digital Camera
A digital camera can be connected to the computer through the 1394 port.
However, not every type or brand of digital camera can be connected to the
computer. Choose the camera that comes with a specially designed
plug for 1394 port (Figure 2-28).
Figure 2-28
User
Page 67
Chapter 2: Operation
’s Manual
2-35
User
Page 68
Chapter 3: BIOS Utilities 3-1
’s Manual
Chapter 3 : BIOS Utilities
This chapter provides you with the information of Power On Self Test
(POST) and shows you how to configure the system parameters using the
System Configuration Utility (SCU).
Power on Self Test (POST)
POST Message: Normal Operation
POST Message: Error Detected
System Configuration Utility (SCU)
Information in the SCU
Initiating the SCU
Working with the Menu Bar of the SCU
Working with the Pull-Down Menu of the SCU
Features of the SCU
Startup Menu
Memory Menu
Disks Menu
Components Menu
Power Menu
Exit Menu
User
Page 69
Chapter 3: BIOS Utilities 3-2
’s Manual
Power on Self Test (POST)
The system BIOS (Basic Input/Output System) performs a series of Power
On Self Test (POST) on system memory and key computer components
every time the computer is turned on. If an error exists, the POST routine
may halt execution (depending on the problem). If no error exists, the
POST will initializes BIOS configuration, then boots the operating system.
POST Message: Normal Operation
You will see the following message if no error exists after the POST is
performed.
SystemSoft MobilePRO BIOS Version 1.01 (2482-00)
Copyright 1983-1996 SystemSoft Corp. All Rights Reserved
233 MHz Pentium with MMX CPU
External Cache: 512KB installed
8 MB Video RAM
SystemSoft Plug-n-Play BIOS Ver.1.17.01
Base Memory 000640 Kb
Extended Memory 064512 Kb
Total Memory 065536 Kb
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration Utility
Note:
You may press the Spacebar key to skip the memory test.
User
Page 70
Chapter 3: BIOS Utilities 3-3
’s Manual
POST Message: Error Detected
If an error is detected, you will see the following WARNING message. You
may press F1 key to continue, or press the Ctrl-Alt-S keys simultaneously
to enter the System Configuration Utility.
SystemSoft MobilePRO BIOS Version 1.01 (2482-00)
Copyright 1983-1996 SystemSoft Corp. All Rights Reserved
233 MHz Pentium with MMX CPU
External Cache: 512KB installed
8 MB Video RAM
SystemSoft Plug-n-Play BIOS Ver.1.17.01
Base Memory 000640 Kb
Extended Memory 064512 Kb
Total Memory 065536 Kb
WARNING – HARD DISK CONTROLLER 1 FAILURE
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration Utility
Press F1 to Continue
User
Page 71
Chapter 3: BIOS Utilities 3-4
’s Manual
Menu Bar Items
Pull-down Menu Items
System Configuration Utility
The System Configuration Utility (SCU) is a ROM-based configuration utility
that displays the system’s configuration status and provides users with a
tool to set their system parameters. The settings are stored in non-volatile
battery-backed CMOS RAM which saves the information even when the
power is turned off, and retains it when the system is turned on again
Information in the System Configuration Utility
The following shows the system settings that may be changed within the
System Configuration Utility.
Startup Date and Time, Fast Boot, Boot Device, Display,
Enable Battery Low Beep, Enable LCD Expand
Mode, Enable Power On Beep, Boot Password,
SCU Password.
Memory Cache Systems.
Disks Enable LS120/ZIP 100 Drive, Diskette Drives, IDE
Settings.
Components COM Ports, MODEM Port, LPT Port, PS/2 Mouse
Port, Microsoft IntelliMouse Support, Keyboard
Numlock, Keyboard Repeat, TV Mode, Video in
Mode, ZV Port Enabled
Power Enable Power Saving, Low Power Saving, Medium
Power Saving, High Power Saving, Customize,
Suspend Controls, Resume Timer, Enable MODEM
Ring Resume, Enable Battery Low Suspend,
Advance CPU Controls.
Exit Save and Exit, Exit (No Save), Default Settings,
Restore Settings, Version Info.
.
User
Page 72
Chapter 3: BIOS Utilities 3-5
’s Manual
Initiating the System Configuration Utility
The System Configuration Utility (SCU) can be accessed when pressing
the Ctrl, Alt, and S keys simultaneously.
<CTRL-ALT-S> to enter System Configuration Utility
The above message only lasts seconds. If you miss it, the computer will
initiate the boot process. You must reboot the system and try again within
the time limit if you want to enter the System Configuration Utility.
Figure 3-1
System Configuration Utility (SCU)
User
Page 73
Chapter 3: BIOS Utilities 3-6
’s Manual
Keys
Action
Description
Working with the Menu Bar
After entering the SCU, you may use the following keys to work with the
menu bar.
Alt Activate menus Activate the System
Configuration Utility.
Left arrow (←)
Right arrow (→)
The highlighted letter
key
Mouse left button
Spacebar
Enter
Mouse right button
Esc
Select menu bar
item.
Accept menu bar
item
Cancel current action Undo the current
Move to a menu bar
item on the left.
Move to a menu bar
item on the right.
Move to the
corresponding menu
bar item.
Enter the selected
menu bar item to
configure settings.
command.
User
Page 74
Chapter 3: BIOS Utilities 3-7
’s Manual
Keys
Action
Description
Working with the Pull-down Menu
When the desired menu bar item is highlighted, press the Enter key to
enter the pull-down menu for values setting. You may use the following
keys to work with the pull-down menu.
Down arrow (↓)
Up arrow (↑)
The highlighted
letter key
Tab
Down/Up arrows
(↓)(↑)
Spacebar Accept entries Enable/disable the
Enter Choose <OK> from a
Esc Reject entries Undo the current
Enter Choose <Cancel>
Alt Activate accelerators Initiate all the
Esc Quit Press the Esc key to
Select pull-down menu
item.
Select a control Move between the
Change values Modify the settings.
Move to the next
pull-down menu item.
Move to the previous
pull-down menu item.
Move to the
corresponding
pull-down menu item.
options.
specified function.
When a check mark
(√) appears, the
function is on.
list of options.
setting.
from a list of options.
highlighted letters
corresponding to their
respective options.
close the pull-down
menu.
User
Page 75
Chapter 3: BIOS Utilities 3-8
’s Manual
Item
Setting/Option
Function
Features of the System Configuration Utility
Startup Menu
Date and Time Day/Month/Year
Hour/Minute/Second
Fast Boot Enable Initialize and quickly
Disable Disable the above.
Boot Device Diskette A Specify where the
Hard Disk C
CD-ROM Drive
Display LCD Activate the system’s
CRT Activate an external
LCD + CRT Activate both the LCD
TV Activate an external TV.
LCD + TV Activate both the LCD
CRT + TV Activate both the CRT
LCD + CRT + TV Activate the LCD, CRT
Enable Battery Low
Beep
Enable LCD Expand
Mode
Enable The system emits a
Disable Disable the above.
Enable Stretch the display to fill
Disable Disable the above.
Set the current date
and time.
boot the system in a
few seconds by
skipping certain
diagnostic tests.
system boots from.
LCD panel.
monitor.
and the CRT.
and the TV.
and the TV.
and TV.
series of warning
beeps sound when the
battery power becomes
low.
the entire viewing area
of the LCD panel.
User
Page 76
Chapter 3: BIOS Utilities 3-9
’s Manual
User
Page 77
Chapter 3: BIOS Utilities 3-10
’s Manual
Item
Setting/Option
Function
Enable Power Enable Enable or Disable Power
On Beep Disable On Beep.
Boot Password Enter old Power-On
Password
Enter new Power-On
Password
Verify new Power-On
Set password for booting
computer. Users are
authorized to start the
system after entering
correct password.
Password
Enable Password to
Power-On
SCU Password Enter old Setup
Password
Enter new Setup
Password
Verify new Setup
Password
Set password for
modifying SCU. Users
are authorized to change
the SCU setting after
entering correct
password.
Enable Setup Password
Figure 3-2
Startup Menu
User
Page 78
Chapter 3: BIOS Utilities 3-11
’s Manual
Item
Setting/Option
Function
Figure 3
-3
Memory Menu
Cache
Systems
L1
Cache
L2
Cache
BIOS
Shadow
Video
Shadow
Disabled Disable the processor’s internal
cache.
Write Back Enable the Processor’s internal
write-back cache.
Disabled Disable the L2 cache controller.
Write Back Enable the LS write-back cache.
Cached
The process of shadowing copies
instructions from system BIOS into
RAM to improve system
performance.
Not
Disable the above.
Cached
Cached
The process of shadowing copies
instructions from video BIOS into
RAM to improve system
performance.
Not
Disable the above.
Cached
Memory Menu
User
Page 79
Chapter 3: BIOS Utilities 3-12
’s Manual
Item
Setting/Option
Function
Figure 3
-4
Disks Menu
Diskette
Drives
Drive A None Specify the drive types
1.44 Mb
2.88 Mb
IDE
Settings
Enable
Primary HDD Drive Enabled Enable enhanced IDE
PIO Mode
CD-ROM /
DVD-ROM /
3th HDD
LS120 /ZIP/
2nd HDD
Drive Enabled
PIO Mode
Drive Enabled
PIO Mode
Enable Enable the LS120 or ZIP
LS120/ZIP
Drive
Disable Disable the LS 120 or
for the diskette drive A.
settings.
drive.
ZIP drive.
Disks Menu
User
Page 80
Chapter 3: BIOS Utilities 3-13
’s Manual
Item
Setting/Option
Function
Components Menu
COM
Ports
LPT Port Port
COM A I/O
Settings
COM B I/O
Settings
Mode
Setting for
COM B
None Specify the COM A
COM1, 3F8, IRQ4
COM2, 2F8, IRQ3
COM3, 3E8, IRQ10
COM4, 2E8, IRQ11
configuration. (COM3
& COM4 Only for DOS
mode and Non-PnP
OS.)
None Specify the COM B
COM1, 3F8, IRQ4
COM2, 2F8, IRQ3
COM3, 3E8, IRQ10
COM4, 2E8, IRQ11
configuration. (COM3
& COM4 Only for DOS
mode and Non-PnP
OS.)
Normal (16550) Define the COM B
IrDA (HPSIR)
hardware.
ASK IR
FAST IR
DMA
Setting for
Fast IR
DMA 0 Specify the Fast IR
DMA 1
DMA configuration.
DMA 3
None Specify the LPT port
Address
LPT1, Addr 378,
and IRQ configuration.
IRQ7
LPT2, Addr 278,
IRQ5
LPT3, Addr 3BC,
IRQ7
Port
Definition
Standard AT (Centronics)
Bidirectional (PS-2)
Enhanced Parallel (EPP)
Extended Capabilities (ECP)
DMA
Setting For
ECP Mode
DMA 1 Specify the
DMA 3
ECP DMA
configuration.
EPP Type EPP 1.7 Specify the
EPP 1.9
EPP type.
User
Page 81
Chapter 3: BIOS Utilities 3-14
’s Manual
Item
Setting/Option
Function
PS/2 Mouse
Port
Enable Enable the system’s
trackpad or an external
PS/2 mouse.
Disable Disable the trackpad or
PS/2 mouse if an
external mouse is
connected to COM A
port.
Microsoft
Intellimouse
Support
Enable Support PS/2 mouse
with the wheel button.
Disable Do not support PS/2
mouse with the wheel
button.
Keyboard
Numlock
Enable Specify whether Num
Disable
Lock is on or off at
system boot time.
Keyboard
Repeat
Key Repeat
Rate
2 cps Define the rate
6 cps
10 cps
15 cps
20 cps
(characters per second)
at which the keyboard
repeats while a key is
depressed.
30 cps
Key Delay 1/4 sec Specify the amount of
1/2 sec
3/4 sec
1 sec
time (second) that will
pass after a key is
depressed before the
key starts to repeat.
TV Mode NTSC Specify the TV mode
PAL
selection
NTSC-Japan
Video in
Mode
Disabled Disable or enable the
Enabled
video in mode.
ZV Port
Enabled
User
Enable Enable or disable the
Disable
ZV port.
Page 82
Chapter 3: BIOS Utilities 3-15
’s Manual
Item
Setting/Option
Function
Figure 3
-5
Modem Port None Specify the Modem Port
Port 3E8, IRQ 11
settings.
Port 2E8, IRQ 11
Port 3F8, IRQ 11
Port 3E8, IRQ 9
Port 2E8, IRQ 9
Port 3F8, IRQ 9
Port 2F8, IRQ 9
Port 2F8, IRQ 11
Components Menu
User
Page 83
Chapter 3: BIOS Utilities 3-16
’s Manual
Item
Setting/Option
Function
Power Menu
Enable Power
Saving
Low Power
Saving
Enable Enable/Disable all
Disable
Enable
Disable
power saving features.
Enable/Disable the
power saving to its
lowest which results in
max. performance but
shortest battery life.
Medium Power
Saving
Enable
Disable
Enable/Disable the
power saving to its
medium which results
in both moderate
performance and
battery life.
High Power
Saving
Enable
Disable
Enable/Disable the
power saving to its
highest which results
in min. performance
but longest battery life.
Customize Disk Standby 5 sec The hard disk will be
10 sec
15 sec
20 sec
30 sec
Always on
put on standby if it is
not accessed within
the specified period.
Hard disk power will
be restored when the
disk drive is accessed
again.
Global Timeout 1 min The system power will
2 min
4 min
6 min
8 min
12 min
16 min
Always on
be reduced if the
system has been idle
over the specified
period. System
power will be restored
when any system
activity is detected.
User
Page 84
Chapter 3: BIOS Utilities 3-17
’s Manual
Item
Setting/Option
Function
Suspend
Controls
Resume Timer Alarm
Enable
MODEM Ring
Resume
Enable Battery
Low Suspend
Advance CPU
Controls
Doze Mode
Suspend
Type
Suspend
Timeout
Resume
Month/Day/Hour/Minute
Enable Resume the system
Disable Disable the above.
Enable Automatically
Disable Disable the above.
Clock Control
Mechanism
Suspend to Disk Specify the suspend
mode for power
Powered on
Suspend
1 min If the system has
5 min
10 min
20 min
30 min
Never
Enable
Disable
Full Mode Specify the type of
management.
been idle for the
specified period, the
system will enter
user-defined
suspend.
Resume the system
from the configured
suspend mode when
resume alarm timer
expires.
The system will
resume at the
specified time
(month, day, hour
and minute).
from STR or POS
mode when a modem
ring is detected
(which modem
should be connected
to the serial port).
suspend the system
to disk upon a low
battery condition.
Processor Clock
Control.
User
Page 85
Chapter 3: BIOS Utilities 3-18
’s Manual
Figure 3
-6
Power Menu
User
Page 86
Chapter 3: BIOS Utilities 3-19
’s Manual
Item
Function
Exit Menu
Save and Exit Save the current settings and reboot the
system.
Exit (No Save) Exit without saving any current changes.
Default Settings Restore the default settings (the original ones
found in ROM).
Restore Settings Restore the current setup settings to the
original custom ones.
Version Info Show current BIOS version information.
Figure 3-7
Exit Menu
User
Page 87
Chapter 4: Troubleshooting 4-1
’s Manual
Chapter 4 : Troubleshooting
Sometimes your computer has some problems. Before you consult the
computer vendor, you can try to solve problems yourself. This chapter
provides you with a list of some commonly experienced problems and their
possible solutions.
Battery
Power
Hard Disk Drive
Floppy Disk Drive
Hardware Installation
LCD Panel
Memory Module
PC Card
Boot Password
Audio
CD
Printer
User
Page 88
Chapter 4: Troubleshooting 4-2
’s Manual
Battery
Problem: The battery pack can not be charged.
Solution 1: The battery pack is exposed to excessively hot and cold
environment. Let it restore to normal condition before you
use it.
Solution 2: The power might be used up.
Problem: The battery pack can not be charged and the charge
indicator turns off.
Solution 1: The battery has been fully charged.
Solution 2: he battery pack is exposed to excessively hot or cold
environment. Let it restore to normal condition before you
use it.
Solution 3: The power is used up.
Problem: The beep sound is heard and the low-battery indicator
turns on.
Solution: The computer is in low-battery status. Please connect
your computer with AC adapter, or press Fn + Esc key
combination to enter suspend mode.
Problem: The beep sound isn’t heard whereas the low-battery
indicator turns on, or the gauge indicates power is less
than 10%.
Solution: The computer is in low battery status. Please adjust the
volume control and connect the computer with AC adapter.
Problem: The actual battery operation time is shorter than
expected.
Solution1: The battery is exposed to excessively high or low
temperature. The ideal temperature for battery operation
is between 50°F and 95°F (10°C and 35°C) whereas
keeping is between 32°F and 113°F (0°C and 45°C).
Solution 2: The battery has released some power. Please recharge
it.
Solution 3: The power management has been turned off.
Solution 4: Some peripheral device or PC card is consuming power.
Turn off the unused device to save power.
Solution 5: The battery has been given a partial charge. When
charging, always fully charge after fully discharge.
User
Page 89
Chapter 4: Troubleshooting 4-3
’s Manual
Power
Problem: The computer can not boot when the battery pack is
not inserted.
Solution 1: The power cord is not correctly connected with AC adapter.
Make sure the power cord is firmly plugged into grounded
outlet and computer.
Solution 2: The grounded outlet is not in normal operation. Check the
outlet’s function or use other outlet.
Problem: The system has automatically entered suspend mode.
Solution 1: The system’s temperature is too high. Let it cool before
you use it.
Solution 2: The system has entered suspend mode after a specified
period of time. Please press any key or touch the
trackpad to wake up the computer.
Hard Disk Drive
Problem: The message “Nonsystem disk” appears.
Solution: The computer is trying to boot from the floppy including no
software. Please take the floppy out and restart the
computer.
Problem: It needs a longer time to read the hard disk drive after
restarting the computer.
Solution 1: The data saved on hard disk drive may be lost. Please
operate the “disk defragmenter” to check the lost unit.
Solution 2: As in low battery status, the computer is waking up from
the suspend mode.
User
Page 90
Chapter 4: Troubleshooting 4-4
’s Manual
Floppy Disk Drive
Problem: The floppy disk drive can not write data to disk.
Solution 1: The floppy is not formatted.
Solution 2: The floppy is write-protected. Please cancel the
protection.
Solution 3: The data is written to incorrect disk drive.
Solution 4: The space left on disk is not enough. Please use a new
disk or delete the unneeded data.
Problem: The disk drive can not read the disk.
Solution 1: The disk is not formatted.
Solution 2: The disk is damaged.
Solution 3: An incorrect disk type is used.
Hardware Installation
Problem: The computer can not recognize the device as part of
the system.
Solution 1: The power switch of new device is not turned on. Please
turn on the power switch, then restart the computer.
Solution 2: You do not rearrange the computer after the device is
installed.
Solution 3: The power cord or the connector between device and
computer is plugged out. Please make sure the device is
firmly connected with the computer.
Solution 4: You do not follow the system configuration as the computer
suggested. Please follow the suggestion.
User
Page 91
Chapter 4: Troubleshooting 4-5
’s Manual
LCD Panel
Problem: The font is too dark.
Solution: The brightness or contrast is not correctly set. Please
press Fn+F7 or Fn+F8 key combination (only limited to
DSTN panel) to adjust the contrast control, and use Fn+F9
or Fn+F10 to adjust the brightness control.
Problem: The screen is blank.
Solution 1: The panel blank application might be set.
Solution 2: The system operates the screen saver after a specified
period of time. Please press any key or touch the
trackpad.
Solution 3: The brightness or contrast needs to be adjusted. Please
press Fn+F7 or Fn+F8 key combination (only limited to
DSTN panel) to adjust the contrast control, and use Fn+F9
or Fn+F10 to adjust the brightness control.
Solution 4: The system has entered suspend mode. Please press
any key or touch the trackpad to wake up the computer.
Problem: The LCD panel displays incorrect font or blinks when
the computer is connected with an external monitor.
Solution: The resolution you use for the monitor exceeds that the
LCD panel can support whereas you have switched to the
LCD panel. Please restart the computer.
User
Page 92
Chapter 4: Troubleshooting 4-6
’s Manual
Memory Module
Problem: The computer can not boot.
Solution: The incorrect type of memory module is installed.
Problem: The memory capacity is not enough.
Solution: The memory is not correctly configurated for the
application.
Problem: The detected memory capacity is not correct.
Solution: Some memory module is not correctly installed or not
compatible with your computer.
Problem: The message “out of memory” is displayed.
Solution: The memory configuration is not correctly set or the
memory is not enough to run the application.
Problem: The message “insufficient memory” is displayed.
Solution: The application can not be operated as the memory is
used up.
PC Card
Problem: The PC card can not be configured.
Solution: The PC card is not supported.
Problem: The system can not recognize the PC card.
Solution 1: The PC card is not inserted into the socket or reversely
inserted.
Solution 2: The PC card driver is not installed.
Solution 3: The PC card or card driver is not compatible with the
computer.
Problem: The beep sound is not heard while the PC card is
inserted.
Solution: The beep sound control is closed.
User
Page 93
Chapter 4: Troubleshooting 4-7
’s Manual
Boot Password
Problem: You forget the boot password.
Solution: While forgetting the password, you must unpack the
computer and delete the memory. Please ask the vendor
for help
Audio
Problem: The audio speaker can not be heard.
Solution: The volume might be set too low. Please check your
volume control.
Problem: The volume is too high (or too low).
Solution: The volume is not correctly set. Please check your
volume control.
Problem: The headphone can not be heard.
Solution 1: The volume is not correctly set. Please check the volume
control.
Solution 2: The volume source is not chosen.
Solution 3: The headphone is plugged into the wrong jack.
User
Page 94
Chapter 4: Troubleshooting 4-8
’s Manual
CD
Problem: The compact disk can not be exited.
Solution: The compact disk is not correctly placed in the tray.
Problem: The compact disk can not be read.
Solution 1: The compact disk is not correctly placed in the tray.
Solution 2: The compact disk is dirty. Please clean it with a CD-ROM
cleaner kit.
Problem: The musical compact disk can be read while the data
disk can not.
Solution: The compact disk hardware for reading data needs to be
checked.
Problem: All compact disks can not be read.
Solution 1: The Windows system can not recognize the CD-ROM drive
or the CD-ROM drive is not compatible with other devices.
Solution 2: The compact disk is dirty. Please clean it with a CD-ROM
cleaner kit.
Solution 3: The compact disk hardware for reading data needs to be
checked.
User
Page 95
Chapter 4: Troubleshooting 4-9
’s Manual
Printer
Problem: The printer can not be set up.
Solution: The printer power cord is not plugged into or the connector
is not correctly connected.
Problem: The printer can not work.
Solution 1: The printer is not power on. Please turn on the printer.
Solution 2: The printer is not in “connected” status. Please set the
printer in “connected” status.
Solution 3: The printer paper is used up. Please add the paper.
Solution 4: The printer driver is not installed or correctly chosen.
Please check the system.
Solution 5: The printer for network is not connected with the network.
Problem: The printer prints incorrect data.
Solution 1: The printer driver is not installed or correctly chosen.
Solution 2: The printer power cord is not plugged into or the connector
is not correctly connected.
User
Page 96
Chapter 4: Troubleshooting
’s Manual
4-10
User
Page 97
Chapter 5: Installing Drivers 5-1
’s Manual
Chapter 5 : Installing Drivers
This chapter provides users the step-by-step instructions of installing
device drivers and utilities. Information has been designed to suit for the
users who has the basic computer knowledge. However, the
unexperienced users also can get good help from the instruction.
Installing Windows 95
Installing Windows 98
Installing Drivers in Windows 95
Installing Drivers in Windows NT4.0
Installing Drivers in Windows 98
User
Page 98
Chapter 5: Installing Drivers 5-2
’s Manual
Installing Windows 95
Preparation for installing Windows 95:
1. Use a bootable floppy disk to start the system.
2. Run FDISK utility from DOS to create a bootable partition.
(See DOS manual for the operation detail.)
3. Format hard disk. Follow the command “Format C:/S” to create a
bootable hard disk and make the boot system file.
(C;/S copies system files to the formatted disk)
4. Run CDINST.COM program from the “CD-ROM Drive Installation
Diskette” that will help you to install CD-ROM driver device
automatically. See the driver manual for detail.
5. Restart the system.
1. Start DOS.
2. Insert the Windows 95 CD-ROM.
3. Go to the “setup” directory, type “setup”, then press [Enter].
4. After the Windows 95 setup program performs a routine check on your
system, press [enter] to continue.
5. When the “Welcome to Windows 95 Setup” screen appears, click
“Continue”.
6. Click “Yes” on the “License Agreement” screen.
7. Click “Next” to select “Collecting Information About your PC”.
8. Click “Next” to select the default of “C:\Windows”, or enter a different
directory.
9. On the screen of “Setup Options”, select “Typical”, then click “Next”.
10. On the screen of “Certificate of Authenticity”, enter the Product
Identification Number, then click “Next”.
11. On the screen of “User Information”, enter your name and company,
then click “Next”.
12. Select “Install The Most Common Components (recommended)”, then
click “Next”.
13. On the screen of “Startup Disk”, insert a blank diskette into the A drive
to create a startup diskette.
14. The Setup Wizard is now copying files. After the copying is finished,
User
Page 99
Chapter 5: Installing Drivers 5-3
’s Manual
remove the disk, then click “OK”.
15. Click “Next” to start copying Windows 95 files to your computer.
16. Click “Finish” to restart Windows 95.
17. On the screen of “Set Up a Printer”, click “Cancel”.
Note:
Do not install a printer at this time. You will not be able to access
the Windows 95 Installation CD until you reboot.
18. Click “OK” to restart the computer.
User
Page 100
Chapter 5: Installing Drivers 5-4
’s Manual
Installing Windows 98
1. Start DOS.
2. Insert the Windows 98 CD-ROM.
3. Type “setup”, then press [Enter].
4. Follow the instructions on the screen and choose the recommended
option.
5. The Windows 98 setup program will check the hard disk drive
automatically.
6. When the setup initializes, click “Continue”.
7. Choose “License Agreement” to agree the contrast.
8. Click “Next” to type the product ID number.
9. Click “Next” . The program will automatically check the system.
10. Choose the directory for your computer. Select the path of
“C:\Windows”, or type another path.
11. For reinstallation, choose “Yes” (recommended) to keep the files.
12. Select your location.
13. To create a Win98 Startup disk, insert a floppy disk into drive A. To
create the startup disk later, choose “cancel”.
14. Press “Next”. The program will copy files to your computer’s hard
disk.
15. At the same time, the screen will show the Win98 concerned
information and the setup items one by one.
16. After the automotive setup stops, restart the computer.
User
Loading...