Page 1
Table of Contents
Chapter 1 : Getting Started 1-1
Unpacking ..................................................................................... 1-2
Operating Environment ................................................................. 1-3
Powering the System .................................................................... 1-4
By AC Power Adapter ............................................................... 1-4
By Battery Pack ........................................................................ 1-5
Opening the LCD Cover ............................................................... 1-6
LED Indicators on the LCD Cover ............................................ 1-7
Top-Front View .............................................................................. 1-8
LCD Panel ................................................................................ 1-8
Stereo Speakers ....................................................................... 1-8
Trackpad and Buttons .............................................................. 1-8
Keyboard .................................................................................. 1-8
Microphone ............................................................................... 1-8
System Status LED Indicators ................................................ 1-10
Power Button .......................................................................... 1-10
Rear View ................................................................................... 1-12
Left-Side View ............................................................................. 1-14
Infrared ................................................................................... 1-15
Right-Side View .......................................................................... 1-16
5.25” CD-ROM Drive .............................................................. 1-16
Ventilation ............................................................................... 1-16
Chapter 2 : Operation 2-1
Replacing the Processor .......................................................... 2-2
Reinstalling Heat Sink .............................................................. 2-3
Setting DIP Switch ........................................................................ 2-4
Accessing DIP Switch............................................................... 2-5
Accessing the Memory Sockets ............................................... 2-7
Installing Memory Module ........................................................ 2-8
Removing Memory Module ...................................................... 2-9
Using Hard Disk Drive ................................................................ 2-10
Removing ............................................................................... 2-10
Replacing Hard Disk Drive ..................................................... 2-11
Using Floppy Disk Drive ............................................................. 2-12
Inserting/Removing Diskettes ................................................. 2-12
Replacing Floppy Disk Drive .................................................. 2-13
Page 2
Using CD-ROM ........................................................................... 2-14
Removing CD-ROM Module ................................................... 2-15
Loading Compact Discs ......................................................... 2-17
Handling Compact Discs ........................................................ 2-18
Using PC Card Sockets .............................................................. 2-19
Inserting PC Cards ................................................................. 2-19
Removing PC Cards ............................................................... 2-19
Using Hot Keys ........................................................................... 2-21
Windows 95 Special Keys ...................................................... 2-22
Using Numeric Keypad ............................................................... 2-23
Using Power Management ......................................................... 2-24
Advanced Power Management (APM 1.2) ............................. 2-24
Advanced Configuration and Power Interface (ACPI) ............ 2-24
Global Standby ....................................................................... 2-24
Hard Disk Standby .................................................................. 2-24
Suspend and Resume ............................................................ 2-25
Attaching Peripheral Devices ...................................................... 2-27
Attaching a Security Lock ....................................................... 2-27
Attaching a Parallel Printer ..................................................... 2-28
Attaching a TV Set .................................................................. 2-29
Attaching a USB-compatible Device ...................................... 2-30
Attaching a Serial Mouse ....................................................... 2-31
Attaching an External Monitor (CRT) ..................................... 2-33
Attaching a PS/2 Keyboard or Mouse .................................... 2-34
Chapter 3 : BIOS Utilities 3-1
Power on Self Test (POST)........................................................... 3-2
POST Message: Normal Operation .......................................... 3-2
POST Message: Error Detected ............................................... 3-3
System Configuration Utility ......................................................... 3-4
Information in the System Configuration Utility ........................ 3-4
Initiating the System Configuration Utility ................................. 3-5
Working with the Menu Bar ...................................................... 3-6
Working with the Pull-down Menu ............................................ 3-7
Features of the System Configuration Utility ............................ 3-8
Appendix A: Specifications I
Page 3
1-1
Chapter 1 : Getting Started
This chapter provides you with the short instruction of notebook computer
system that will help you to get the basic understanding about the
computer.
Unpacking
Operating Environment
Powering the System
By AC Power Adapter
By Battery Pack
Opening the LCD Cover
Top-Front View
Rear View
Left-side View
Right-side View
Chapter 1: Getting
Started
Page 4
1-2
Unpacking
Carefully unpack the notebook computer and the included accessories
(Figure 1-1). Check the items one by one. If there is something wrong,
contact your dealer immediately.
Notebook Computer.
Carrying Bag.
Power Adapter.
Power Cord.
User Manual.
PS/2 Transfer Cable.
Battery Pack.
Utilities Diskette(s).
User’s Manual
Figure 1-1
Page 5
1-3
Operating Environment
As with any other precision electronic equipment, proper care and
operation of your computer will prolong the use period. Make sure that the
computer is not:
Exposed to excessively heat or direct sunlight.
Shocked or vibrated.
Exposed to strong magnetic fields.
Left in a place where foreign matter or moisture may affect the
system.
Figure 1-2
Chapter 1: Getting
Started
Page 6
1-4
Powering the System
You can use the AC power adapter or battery pack to power the computer
system.
By AC Power Adapter
Use only the power adapter that comes with your computer. An incorrect
type of power adapter will cause damage to the computer and its
components.
1.
Plug the power adapter cord into the AC-in socket on the rear panel of
the computer.
2.
Connect the power adapter with the power cord.
3.
Plug the power cord into a properly grounded outlet (Figure 1-3).
4.
Refer to Chapter 1, LED Indicators for more information on system
power status.
User’s Manual
Figure 1-3
Page 7
1-5
By Battery Pack
The battery pack provides power for continuous portable operation of the
computer. When using the battery no external power source is required.
The actual operation time is related to the application and the
configuration you’re using.
Inserting
1. Turn the computer over.
2. Fit the battery pack firmly into the computer.
3. The latch will click into the place when it is seated.
Removing
1. Turn the computer over.
2. Press the latch in the indicated direction to release the battery pack
(Figure 1-4).
3. Carefully lift the battery pack from the computer (Figure 1-5).
Chapter 1: Getting
Started
Figure 1-4
Figure 1-5
Page 8
1-6
Figure 1
-7
Opening the LCD Cover
1. Move the latch to the right to release the top cover. (Figure 1-6).
2. Lift the top cover to reveal the LCD panel and keyboard (Figure 1-7).
3. Adjust the LCD panel to a comfortable viewing angle.
4. Press the power button to turn the system on or off (refer to Chapter1,
Top-Front View for more information on the power button).
Figure 1-6
User’s Manual
Page 9
1-7
LED Indicators on the LCD Cover
Icon Color Description
Green Battery power is used while the system is
turned on.
Red AC power is used while the system is
turned on.
Green Battery is fully charged.
Red Battery is being charged.
Blinking Red Battery power is critically low.
Note:
The light of the indicator will blink when the battery is overheated.
Chapter 1: Getting
Started
Figure 1-8
Page 10
1-8
Top-Front View
LCD Panel
The computer provides you with a SVGA, LCD panel. Depending
on the model you purchased, it can either be a 12.1” or 12.0” TFT flat
panel. The LCD panel is driven by a AGP bus video controller with
4MB video memory.
Stereo Speakers
Two built-in speakers provide 3D stereo sound system.
Trackpad and Buttons
The pointing device features a sensitive glide pad for precise
movements. It functions like a two-button mouse does. The right
trackpad button is equivalent to the right mouse button; the left
trackpad button is equivalent to the left mouse button.
Keyboard
The 84-key Windows 95 keyboard is integrated with the numeric
keypad.
Microphone
The built-in microphone provides clear sound effect.
User’s Manual
Page 11
1-9
LCD Panel
Microphone
Keyboard
Trackpad and Button
Stereo Speakers
Figure 1-9
Chapter 1: Getting
Started
Page 12
1-10
System Status LED Indicators
The LED indicators display the system’s operation status.
Icon Color Description
Green Battery power is used while the system is
Red AC power is used while the system is
Green Battery is fully charged.
Red Battery is being charged.
Blinking Red Battery power is critically low.
Green The system has entered the configured
Green The embedded numeric keypad feature is
Green The Caps Lock feature is activated.
Green The Scroll Lock feature is activated.
Green The hard disk is being accessed.
Power Button
turned on.
turned on.
suspend mode.
activated
Use this button to turn the system on or off.
After proper configuration under SCU, this button can be
used as suspend/resume hot button (refer to Chapter 3:
BIOS Utilities, Power Menu for more information).
User’s Manual
Page 13
1-11
Note: After turning off the system, wait for a few seconds to power it on
again.
Power Button
Figure 1-10
LED Indicators
Figure 1-11
Chapter 1: Getting
Started
Page 14
1-12
Rear View
AC-in Socket
Plug the AC adapter into this socket for power supply. To
disconnect, pull the plug (not the cord) directly back.
Parallel Port
This parallel port supports EPP (Enhanced Parallel Port) and
ECP (Extended Capabilities Port) modes.
S-Video Jack
Use this jack to transmit video signal to a TV set. You may
need to select the video standard (NTSC/PAL) for video display
(please refer to Chapter 3, Components Menu for more
information).
USB Port
The Universal Serial Bus (USB) port simplifies the expansion
capability for peripheral devices.
Serial Port
The serial port features a 9-pin connector for the external
addition, such as mouse or fax/modem.
External Monitor (CRT) Port
This port is used for transmission of the display to an external
monitor. Simultaneous display in LCD screen and external
CRT monitor is available.
PS/2 Type Port
This port is used to connect with a PS/2 type keyboard or
mouse.
User’s Manual
Page 15
1-13
Phone Jack
The phone jack is used to support the built-in modem. To use
the function, attach a phone line to the jack and insert a modem
card (optional) into the modem socket on the mainboard.
USB Port
Serial Port
Parallel Port
AC-in Socket
CRT Port
S-Video Jack
Figure 1-12
Chapter 1: Getting
Started
PS/2 Type Port
Phone Jack
Page 16
1-14
Left-Side View
PC Card Sockets
There are two PC card sockets on the right side and left side.
Two type II PCMCIA 3.3V/5V cards can be used to expand
the system’s capability. The sockets support Zoom Video
Mode and CardBus. To eject the PC card, press the
appropriate eject button.
2.5” Hard Disk Drive
The 2.5” hard disk drive is removable. It accepts any 2.5”
hard disk drive with a height of 12.7mm or less. The system
supports Master mode IDE and PIO mode 4/ATA-33 (Ultra
DMA).
3.5” Floppy Disk Drive
The computer provides a built-in 3.5”, 3-mode, 1.44MB floppy
disk drive. To eject the disk, press the button on the top-right
side. The floppy disk module can be replaced with a
12.7mm(h) LS-120 drive. (Refer to Chapter 2: Operation for
more information).
Headphone Jack
Headphone and speakers can be attached to the system
through this jack.
Microphone-in Jack
Use this jack to connect a microphone to the system.
User’s Manual
Page 17
1-15
Infrared
The system adopts infrared technology as the interface for simple,
fast and convenient data exchange from the computer to an
infrared-compatible device. The infrared port supports IrDA
(HPSIR) 1.0 mode and Amplitude Shifted Keyed IR (ASKIR) mode.
For further information, please refer to the manual of the wireless
device you wish to connect on how to use the point-and-shoot
operation.
Microphone-in Jack
PC Card Socket
Infrared
Headphone Jack
3.5” Floppy Disk Drive
2.5” Hard Disk Drive
Figure 1-13
Chapter 1: Getting
Started
Page 18
1-16
Right-Side View
5.25” CD-ROM Drive
The 5.25” IDE CD-ROM module is designed to be removable. The
eject button is located in the middle of the front cover of the CD-ROM
drive. Pressing it will release the CD tray.
Ventilation
The computer provides ventilation to dissipate the system’s operation
heat. Do not block or obstruct it during operation.
PC Card Socket
User’s Manual
5.25” CD-ROM Drive
Figure 1-14
Ventilation
Page 19
2-1
Chapter 2 : Operation
The notebook computer has many advanced features to help you with your
computer work. This chapter describes each of the computer’s hardware
features and shows you how to use them.
Before you begin working with the internal components of the computer,
remove the battery and disconnect the AC power adapter.
Make sure you wear an anti-static wrist strap to ground yourself before
working with or repair the internal components. Static electricity may
damage the components.
Upgrading Processor Module
Setting DIP Switch
Expanding Memory
Using Hard Disk Drive
Using Floppy Disk Drive
Using CD-ROM
Using PC Card Sockets
Using Hot Keys
Using Numeric Keypad
Using Power Management
Attaching Peripheral Devices
Chapter 2:
Operation
Page 20
2-2
Upgrading Processor Module
The notebook supports Intel Celeron processor at 300MHz, 333MHz,
366MHz, 400MHz and 433MHz Core frequencies.
The Intel Celeron processor provides good performance for applications
running on advanced operating systems, such as Window 95/98,
Window NT, and UNIX.
Replacing the Processor
1. Remove all the power sources (AC power and battery).
2. Turn the computer over.
3. Remove the CPU cover.
4. Remove the screws that fasten the heat sink mounted on the
processor.
5. Carefully detach the processor from the mainboard (Figure 2-1).
CPU Cover
Heat Sink and Fan
Processor Module
User's Manual
Figure 2-1
Page 21
2-3
Reinstalling Heat Sink
Reinstall the CPU in the reverse order of removal. Make sure that the
heat sink cable is properly installed (Figure 2-2 & 2-3).
Figure 2-2
Figure 2-3
Chapter 2:
Operation
Page 22
2-4
BGA1 Processor
CPU Frequency
SW1-1 SW1
-2
SW1
-3
SW1
-4
Celeron & Dixon Processor VTT Select
CPU Frequency
S3-1 S3-2
Setting DIP Switch
You need to set the following DIP switches for correct system configuration:
❍
4-pole & 2-pole DIP switches for CPU core frequency
The correct configuration is listed as below:
233MHZ OFF OFF OFF ON
266MHZ ON ON ON OFF
300MHZ OFF ON ON OFF
333MHZ ON OFF OFF OFF
366MHZ OFF OFF OFF OFF
*Only for BGA1 CPU
1.5V (Socket 370) ON ON
1.6V (BGA1) OFF OFF
User's Manual
Page 23
2-5
Accessing DIP Switch
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its normal
position (Figure 2-4).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the DIP switches to set the configuration (Figure 2-5).
Figure 2-4
Figure 2-5
Chapter 2:
Operation
Page 24
2-6
Bank 0
Bank 1
Power
Total Size
( 64 Bits)
( 64 Bits)
Expanding Memory
The system has two memory sockets for different RAM modules to expand
the memory up to 256MB. The RAM modules should be 144-pin SODIMM
(Small Outline Dual In-line Memory Module) type. The computer supports
EDO, and SDRAM operation. The total memory size is automatically
detected by the POST routines. To expend the memory, you have the
following choice with different DRAM combination
8 0 8
8 8 16
16 8 24
32 0 32
16 16 32
32 16 48
64 8 72
64 16 3.3V 80
32 32 64
64 32 96
128 0 128
64 64 128
128 8 136
128 16 144
128 32 160
128 64 192
128 128 256
User's Manual
Page 25
2-7
Non-component area
Accessing the Memory Sockets
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its
normal position (Figure 2-4).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the memory sockets (Figure 2-6 & Figure 2-7).
67.6mm
31.75mm
(The edges of the memory module
are the non-component area.)
Chapter 2:
Operation
Figure 2-6
Bank 1
Bank 0
Figure 2-7
Page 26
2-8
Installing Memory Module
Follow the steps below to install the memory module:
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its
normal position (Figure 2-4).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the memory sockets (Figure 2-7).
4.
Insert the memory module at a slight angle (45 ∘ ) and fit its
connectors into the socket firmly (Figure 2-8).
Note:
Insert Bank o first, then Bank 1.
5.
Press the two edges of the memory module to make it locked into the
place.
6.
Reinstall the keyboard assembly.
User's Manual
Figure 2-8
Page 27
2-9
Removing Memory Module
1.
Turn the system power off.
2.
Press the two keyboard latches to elevate the keyboard from its
normal position (Figure 2-4).
3.
Carefully lift the keyboard assembly out to expose the mainboard.
Locate the memory sockets (Figure 2-7).
4.
Gently pull the two latches outward on both ends of the module. The
module will pop up (Figure 2-9).
5.
Remove the memory module.
6.
Reinstall the keyboard assembly.
Chapter 2:
Operation
Figure 2-9
Page 28
2-10
Using Hard Disk Drive
The hard disk drive is mounted in a removable case and can be taken out
to accommodate other 2.5” IDE hard disk drives with a height of 12.7mm.
The system supports PIO mode 4, Master mode IDE, LBA mode and
provides a high performance data transfer rate at speeds up to 33
MBytes/second (ATA-33).
Removing
1.
Turn the system power off.
2.
Turn the computer over.
3.
Locate the Hard Disk Drive latch.
4.
Press the latch in the indicated direction and take the hard disk drive
out of the computer (Figure 2-10).
Note:
When inserting the hard disk drive, Insert it firmly into the computer. Make
sure you feel the drive click into the position when it is seated properly.
User's Manual
Figure 2-10
Page 29
2-11
Replacing Hard Disk Drive
The hard disk drive is contained in a case. To take the hard disk drive out
of the case and replace with another one, you need to remove the two
screws on each side of the case (Figure 2-11). The location of the two
screws may be varied depending on different types of hard disk model.
Gently disconnect the cable from the hard disk drive when taking it out of
the case. Be careful not to bend any pins or crimp the cable.
Figure 2-11
Chapter 2:
Operation
Page 30
2-12
Using Floppy Disk Drive
The computer is equipped with a removable 1.44MB, 3.5” floppy disk drive
module. It is usually designated as drive A: by default and can be used as
a boot device if properly set in SCU (please refer to Chapter 3: BIOS
Utilities). You may replace the floppy disk drive module with a 120MB
LS-120 drive (of 12.7mm high). Contact your dealer for the detail.
Inserting/Removing Diskettes
When using the floppy drive, always insert your floppy diskette label-side
up (Figure 2-12). To remove your diskette, press the eject button on the
top-right corner of the floppy drive.
User's Manual
Figure 2-12
Page 31
2-13
Replacing Floppy Disk Drive
Note:
Before replacing floppy disk drive and CD-ROM module, you need to
remove the cover between the two modules.
1.
Turn the system power off.
2.
Turn the computer over.
3.
Locate the cover between the floppy disk drive and the CD-ROM
module.
4.
Remove the two screws to release the cover (Figure 2-13).
5.
Locate the floppy disk drive latch.
6.
Push the latch in the indicated direction and pull the floppy disk drive
module out of the tray (Figure 2-14).
7.
Insert the replacement module into the bay.
Figure 2-13
Chapter 2:
Operation
Figure 2-14
Page 32
2-14
Using CD-ROM
The notebook computer comes standard with a removable 5.25” CD-ROM
module. It is labeled drive D: and may be used as a boot device if
properly set.
To insert a CD, press the Eject Button and place the CD into the Disc
Tray with label-side facing up. Push the CD tray in and you are ready to
start. The Busy Indicator will light up while data is being accessed or
while an audio CD is playing. When the power is unexpectedly interrupted,
insert an instrument such as a straightened paper clip into the Emergency
Eject Hole to eject the tray (Figure 2-15).
Busy Indicator
Eject Button
Disc Tray
Emergency Eject
User's Manual
Figure 2-15
Page 33
2-15
Removing CD-ROM Module
Note:
Before replacing floppy disk drive and CD-ROM module, you need to
remove the cover between the two modules.
1. Turn the system power off.
2. Turn the computer over.
3. Locate the cover between the floppy disk drive and the CD-ROM
module.
4. Remove the two screws to release the cover (Figure 2-13).
5. Locate the CD-ROM latch.
6. Push the latch in the indicated direction and pull the CD-ROM module
out of the tray (Figure 2-16).
7. Insert the replacement module into the bay.
Figure 2-16
Chapter 2:
Operation
Page 34
2-16
User's Manual
Page 35
2-17
Loading Compact Discs
1.
Turn on the power.
2.
Press the CD-ROM eject button; the disc tray will pop out partially.
3.
Pull the disc tray out.
4.
Carefully load the CD into the disc tray with label-side facing up.
Press it gently to ensure it fits into the place (Figure 2-17).
5.
Push the tray into the computer.
Figure 2-17
Chapter 2:
Operation
Page 36
2-18
Handling Compact Discs
Proper handling of your CDs will prevent them from being damaged and
ensure the accessibility of data stored in them.
❍
Hold the CD by the edges; do not touch the surface of the disc.
❍
Use clean, soft, and dry cloth to remove dust or fingerprints.
❍
Do not use pen to write on the surface.
❍
Do not attach any paper or other materials to the surface of the disk.
❍
Do not store or place the CD in the high-temperature areas.
❍
Do not use benzine, thinners, or other cleaners to clean the CD.
❍
Do not bend the compact disc.
❍
Do not drop or subject the CDs to shock.
User's Manual
Page 37
2-19
Using PC Card Sockets
The computer is equipped with two PC card sockets (previously referred to
as PCMCIA). Both sockets support two 3.3V/5V typeII PC cards or two
3.3V CardBus cards
The PC card sockets are located on the computer’s right side and left side.
The socket on left side is named socket A which supports Zoom Video Port.
Inserting PC Cards
1. Open the access door
2. Align the PC card with the slot and push it in firmly until it locks into the
place (Figure 2-18 & 2-19).
Removing PC Cards
To remove a PC card, press the appropriate eject button to eject the card
from its slot.
Chapter 2:
Operation
Page 38
2-20
Figure 2-18
Eject Button
Socket A
User's Manual
Socket B
Eject Button
Figure 2-19
Page 39
Put the system in a suspend state for power
2-21
Using Hot Keys
Located on the bottom-left edge of the keyboard layout is a colored Fn key.
The Fn key function allows you to change operational features instantly.
When you use the following functions, press and hold the Fn key; then
press the appropriate function key (Figure 2-20).
Hot Keys System Features
Fn + F3
Fn + F4
Fn + F6
Fn + F9
Fn + F10
Fn + F11
Fn + F12
Fn + Z
Fn + Esc
Expand LCD display.
Control display top/center position.
Toggle CRT/LCD/LCD+CRT/TV/CRT+TV.
Decrease LCD brightness.
Increase LCD brightness.
Decrease audio volume.
Increase audio volume.
Turn audio mute on/off.
management.
Chapter 2:
Operation
Page 40
2-22
Windows 95 Special Keys
he keyboard provides two keys that have special functions in Windows 95:
This key has the same functions as the secondary mouse does.
This key activates the Windows 95 Start menu.
Figure 2-20
User's Manual
Page 41
2-23
Using Numeric Keypad
The computer features a 102-key keyboard with an integrated numeric
keypad for easy numeric data input (Figure 2-21).
Figure 2-21
Chapter 2:
Operation
Page 42
2-24
Using Power Management
The system provides you with various modes to manage its power
consumption while maintaining system performance. Please refer to
Chapter 3: BIOS Utilities, System Configuration Utility, Power Menu for
more information.
Advanced Power Management (APM 1.2)
The system provides built-in Advanced Power Management (APM 1.2)
support to reduce power consumption. APM function varies depending on
the operation system you are using. Some operation systems do not
support APM, such as Windows NT, and therefore, cannot take
advantage of the system’s capabilities in this area.
Advanced Configuration and Power Interface
(ACPI)
The ACPI interface gives the operation system (OS) direct control over the
power management and Plug and Play functions of a computer. The
operation system can perform the functions covered by the ACPI
specification, such as system power management, device power
management, and thermal management.
Global Standby
In Global Standby mode, the CPU clock will be stopped and most
controllable peripheral devices will be power off. If the idle timer expires
before any system activity is detected, the system will change from Standby
mode into Suspend mode.
Hard Disk Standby
The system will turn off the computer’s hard disk drive motor if it has not
been accessed after a specified period of time. The motor will be turned
back on if the system attempts to read or write data to it.
User's Manual
Page 43
2-25
Suspend and Resume
When at extremely low power, you can enter suspend mode to save power.
In suspend mode, all tasks are stopped and stored in memory to save
power. The system features two levels of suspend mode:
Powered-On-Suspend (POS) mode and Suspend-To-Disk (STD) mode.
Another useful feature is resume mode. This feature allows you to turn
the computer’s power off without exiting your software application. When
you turn the power on again, you can resume work where you left off,
because the screen display is restored as you left it. This saves time and
battery power.
Caution: Do not enter suspend mode when you are
1. Accessing any of the disk drives, such as HDD, FDD or CD-ROM drives.
2. Using the audio features or playing back video.
3. Playing a DOS game.
Powered On Suspend (POS)
Of the suspend modes, Powered-On-Suspend saves the least amount of
power. However, it takes the shortest time to return to full operation.
Resume from POS Mode
The system can resume from Powered-On-Suspend mode by:
Alarm resume (month/day/hour/minute)
Modem ring
Pressing any keyboard key.
Pressing the power button (if configured as Suspend/Resume function
under SCU)
Opening the display lid (only if the suspend mode is initiated by closing
the display lid)
Chapter 2:
Operation
Page 44
2-26
Suspend To Disk (STD)
Suspend to Disk is a 0-volt suspend mode for system power management.
STD mode saves the maximum power but takes the longest time to return
to full operation.
1.
Use your operation system’s FDISK program to delete all partitions of
the hard disk if any already exist on the target drive.
2.
Boot the system and run the 0VMAKFIL.EXE Utility to create the
Suspend to Disk partition on the hard disk. The size of Suspend to Disk
partition will be the installed DRAM (n) plus 4MB integrated video RAM.
:\>0VMAKFIL –Pn
For example, if the system DRAM is 32MB, 0VMAKFIL will create a
partiton size of approximately 36MB.
:\>0VMAKFIL –P32
Resume from STD Mode
The system will resume from Suspend-To-Disk mode by:
Power back on
Alarm resume (month/day/hour/minute)
Suspend To RAM (STR)
Suspend-To-RAM mode is the medium level of system power management.
Resume from STR Mode
The system will resume from Suspend-To RAM mode by:
Alarm resume (month/day/hour/minute)
Modem ring
Pressing the power button (if configured as Suspend/Resume
function under SCU)
Opening the display lid (only if the suspend mode is initiated by
closing the display lid)
User's Manual
Page 45
2-27
Attaching Peripheral Devices
To extend the computer’s functions, you can attach the following peripheral
devices to the computer through the ports or jacks on the rear panel of
computer.
Attaching a Security Lock
The security lock is equipped to protect your computer from being stolen.
To install the security lock, wrap the cable around a desk or other
immovable object, then insert the locking device into the connector (Figure
2-22).
Figure 2-22
Chapter 2:
Operation
Page 46
2-28
Attaching a Parallel Printer
You may connect any standard Centronics parallel printer to your computer
through the parallel port.
1.
Turn the system power off.
2.
Connect the cable to the parallel port on the rear of the computer.
3.
Tighten the screws that fasten the cable to the parallel port (Figure
2-23).
4.
Insert the other end of the cable to the printer’s connector. Fasten
the cable’s connector.
5.
Turn on the printer and computer.
In addition, you also need to install the manufacturer-supplied driver for the
printer. Refer to the device’s user’s guide for more information. If the
connected printer supports EPP (Enhanced Parallel Port) or ECP
(Extended Capabilities Port) mode, please enter System Configuration
Utility (SCU) to configure the required setting.
User's Manual
Figure 2-23
Page 47
2-29
Attaching a TV Set
The S-Video jack on the rear panel of the computer is used for transmitting
video signals to a TV set. You may need to select the video standard for
video display. Enter the System Configuration Utility (SCU), Components
Menu to specify the appropriate TV mode. Simultaneous display on
external monitor (CRT) and TV is available. You can enter the SCU to
select the appropriate parameters or use the Fn + F6 keys (refer to Chapter
2, Using Hot Keys).
Attach the TV set as shown below (Figure 2-24).
Figure 2-24
Chapter 2:
Operation
Page 48
2-30
Attaching a USB-compatible Device
The computer provides a USB port for the connection of a USB-compatible
keyboard, mouse, or other devices. Attach the device as shown below
(Figure 2-25).
User's Manual
Figure 2-25
Page 49
2-31
Attaching a Serial Mouse
The serial port features a 9-pin connector. You can connect any serial
device such as a mouse to this port.
1.
Turn the system power off.
2.
Connect the cable to the serial port on the rear of the computer.
3.
Tighten the screws that fasten the cable to the serial port (Figure
2-26).
4.
Turn on the computer.
In addition, you may need to install the manufacturer-supplied driver for the
serial mouse. Refer to the device’s user’s guide for more information.
Chapter 2:
Operation
Figure 2-26
Page 50
2-32
Figure 2-25
User's Manual
Page 51
2-33
Attaching an External Monitor (CRT)
The computer is capable of displaying not only on the LCD, but also on the
XGA compatible displays attached to the computer. Information can be
displayed on both the LCD and the external monitor simultaneously. Enter
the System Configuration Utility (SCU) to select the appropriate parameters
or use the Fn + F6 keys (refer to Chapter 2, Using Hot Keys).
1.
Turn the system power off.
2.
Connect the cable to the CRT port on the rear of the computer.
3.
Tighten the screws that fasten the cable to the CRT port (Figure 2-27).
4.
Insert the other end of the cable to the external monitor.
5.
Turn on the computer.
Chapter 2:
Operation
Figure 2-27
Page 52
2-34
Attaching a PS/2 Keyboard or Mouse
The computer can be operated with a PS/2 keyboard or mouse attached by
means of the PS/2 transfer cable. Attach the external keyboard or mouse
as shown below (Figure 2-28).
Both PS/2 type ports on the rear panel of the computer can be used for the
connection of a PS/2 keyboard and mouse.
User's Manual
Figure 2-28
Page 53
3-1
Chapter 3 : BIOS Utilities
This chapter provides you with the information of Power On Self Test
(POST) and shows you how to configure the system parameters using the
System Configuration Utility (SCU).
Power on Self Test (POST)
POST Message: Normal Operation
POST Message: Error Detected
System Configuration Utility (SCU)
Information in the SCU
Initiating the SCU
Working with the Menu Bar of the SCU
Working with the Pull-Down Menu of the SCU
Features of the SCU
Startup Menu
Memory Menu
Disks Menu
Components Menu
Power Menu
Exit Menu
Chapter 5: Installing
Drivers
Page 54
3-2
Power on Self Test (POST)
The system BIOS (Basic Input/Output System) performs a series of Power
On Self Test (POST) on system memory and key computer components
every time the computer is turned on. If an error exists, the POST routine
may halt execution (depending on the problem). If no error exists, the
POST will initializes BIOS configuration, then boots the operating system.
POST Message: Normal Operation
You will see the following message if no error exists after the POST is
performed.
SystemSoft BIOS MobilePRO BIOS Version 1.01 (2482-00)-(R1.00.tr02)
Copyright 1983-1996 SystemSoft Corp. All Rights Reserved
300 MHz Celeron with MMX CPU
L2 Cache: 128KB Installed
4 MB Video RAM
SystemSoft Plug-n-Play BIOS ver1.17.01
Base Memory 000640 Kb
Extended Memory 130048 Kb
Total Memory 131072 Kb
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration Utility
Note:
You may press the Spacebar key to skip the memory test.
User's Manual
Page 55
3-3
POST Message: Error Detected
If an error is detected, you will see the following WARNING message. You
may press F1 key to continue, or press the Ctrl-Alt-S keys simultaneously
to enter the System Configuration Utility.
SystemSoft BIOS MobilePRO BIOS Version 1.01 (2482-00)-(R1.00.tr02)
Copyright 1983-1996 SystemSoft Corp. All Rights Reserved
300 MHz Celeron with MMX CPU
L2 Cache: 128KB Installed
4 MB Video RAM
SystemSoft Plug-n-Play BIOS ver1.17.01
Base Memory 000640 Kb
Extended Memory 130048 Kb
Total Memory 131072 Kb
WARNING – HARD DISK CONTROLLER 1 FAILURE
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration Utility
Press F1 to Continue
Chapter 5: Installing
Drivers
Page 56
3-4
Menu Bar Items
Pull-down Menu Items
System Configuration Utility
The System Configuration Utility (SCU) is a ROM-based configuration utility
that displays the system’s configuration status and provides users with a
tool to set their system parameters. The settings are stored in non-volatile
battery-backed CMOS RAM which saves the information even when the
power is turned off, and retains it when the system is turned on again
Information in the System Configuration Utility
The following shows the system settings that may be changed within the
System Configuration Utility.
Startup Date and Time, Fast Boot, Boot Device, Display,
Enable Battery Low Beep, Enable LCD expand
Mode, Enable Power On Beep, Enable PNP OS
Support, Boot Password, SCU Password.
Memory Cache Systems.
Disks Enable LS120/ZIP 100 Drive, Diskette Drives, IDE
Settings.
Components COM Ports, LPT Port, PS/2 Mouse Port, Microsoft
IntelliMouse Support, Keyboard Numlock, Keyboard
Repeat, TV Mode
Power Enable Power Saving, Low Power Saving, Medium
Power Saving, High Power Saving, Customize,
Suspend Controls, Resume Timer, Enable MODEM
Ring Resume, Enable Battery Low Suspend,
Advance CPU Controls.
Exit Save and Exit, Exit (No Save), Default Settings,
Restore Settings, Version Info.
.
User's Manual
Page 57
3-5
Initiating the System Configuration Utility
The System Configuration Utility (SCU) can be accessed when pressing
the Ctrl, Alt, and S keys simultaneously.
<CTRL-ALT-S> to enter System Configuration Utility
The above message only lasts seconds. If you miss it, the computer will
initiate the boot process. You must reboot the system and try again within
the time limit if you want to enter the System Configuration Utility.
Figure 3-1
System Configuration Utility (SCU)
Chapter 5: Installing
Drivers
Page 58
3-6
Keys
Action
Description
Working with the Menu Bar
After entering the SCU, you may use the following keys to work with the
menu bar.
Alt Activate menus Activate the System
Configuration Utility.
Left arrow (←)
Right arrow (→)
The highlighted letter
key
Mouse left button
Spacebar
Enter
Mouse right button
Esc
Select menu bar
item.
Accept menu bar
item
Cancel current action Undo the current
Move to a menu bar
item on the left.
Move to a menu bar
item on the right.
Move to the
corresponding menu
bar item.
Enter the selected
menu bar item to
configure settings.
command.
User's Manual
Page 59
3-7
Keys
Action
Description
Working with the Pull-down Menu
When the desired menu bar item is highlighted, press the Enter key to
enter the pull-down menu for values setting. You may use the following
keys to work with the pull-down menu.
Down arrow (↓)
Up arrow (↑)
The highlighted
letter key
Tab
Down/Up arrows
(↓)(↑)
Spacebar Accept entries Enable/disable the
Enter Choose <OK> from a
Esc Reject entries Undo the current
Enter Choose <Cancel>
Alt Activate accelerators Initiate all the
Esc Quit Press the Esc key to
Select pull-down menu
item.
Select a control Move between the
Change values Modify the settings.
Move to the next
pull-down menu item.
Move to the previous
pull-down menu item.
Move to the
corresponding
pull-down menu item.
options.
specified function.
When a check mark
(√) appears, the
function is on.
list of options.
setting.
from a list of options.
highlighted letters
corresponding to their
respective options.
close the pull-down
menu.
Chapter 5: Installing
Drivers
Page 60
3-8
Item
Setting/Option
Function
Features of the System Configuration Utility
Startup Menu
Date and Time Day/Month/Year
Hour/Minute/Second
Fast Boot Enable Initialize and quickly
Disable Disable the above.
Boot Device Diskette A Specify where the
Hard Disk C
CD-ROM Drive
Display LCD Activate the system’s
CRT Activate an external
LCD + CRT Activate both the LCD
TV Activate an external TV.
CRT + TV Activate both the CRT
Enable Battery Low
Beep
Enable LCD Expand
Mode
Enable The system emits a
Disable Disable the above.
Enable Stretch the display to fill
Disable Disable the above.
Set the current date
and time.
boot the system in a
few seconds by
skipping certain
diagnostic tests.
system boots from.
LCD panel.
monitor.
and the CRT.
and the TV.
series of warning
beeps sound when the
battery power becomes
low.
the entire viewing area
of the LCD panel.
User's Manual
Page 61
3-9
Item
Setting/Option
Function
Enable Power
on Beep
Enable PNP
OS Support
Enable Enable or disable Power
Disable
Enable Enable or disable PNP
Disable
Boot Password Enter old Power-On
Password
Enter new Power-On
Password
Verify new Power-On
Password
Enable Password to
Power-On
SCU Password Enter old Setup
Password
Enter new Setup
Password
Verify new Setup
Password
Enable Setup Password
on Beep.
OS Support.
Set password for booting
computer. Users are
authorized to start the
system after entering
correct password.
Set password for
modifying SCU. Users
are authorized to change
the SCU setting after
entering correct
password.
Figure 3-2
Startup Menu
Chapter 5: Installing
Drivers
Page 62
3-10
Item
Setting/Option
Function
Figure 3
-3
Memory Menu
Cache
Systems
L1
Cache
L2
Cache
BIOS
Shadow
Video
Shadow
Disabled Disable the processor’s internal
cache.
Write Back Enable the Processor’s internal
write-back cache.
Disabled Disable the L2 cache controller.
Write Back Enable the LS write-back cache.
Cached
The process of shadowing copies
instructions from system BIOS into
RAM to improve system
performance.
Not
Disable the above.
Cached
Cached
The process of shadowing copies
instructions from video BIOS into
RAM to improve system
performance.
Not
Disable the above.
Cached
User's Manual
Memory Menu
Page 63
3-11
Chapter 5: Installing
Drivers
Page 64
3-12
Item
Setting/Option
Function
Figure 3
-4
Disks Menu
Diskette
Drives
Drive A None Specify the drive types
1.44 Mb
2.88 Mb
IDE
Settings
Enable
LS120/
ZIP100
Primary HDD Drive Enabled Enable enhanced IDE
PIO Mode
CD-ROM /
DVD-ROM
LS120 /ZIP/
2nd HDD
Drive Enabled
PIO Mode
Drive Enabled
PIO Mode
Enable Enable the LS120 drive.
Disable Disable the LS 120 drive.
Drive
for the diskette drive A.
settings.
User's Manual
Disks Menu
Page 65
Item
Setting/Option
Function
3-13
Components Menu
COM
Ports
LPT Port Port
COM A I/O
Settings
COM B I/O
Settings
Mode
Setting for
COM B
None Specify the COM A
COM1, 3F8, IRQ4
COM2, 2F8, IRQ3
COM3, 3E8, IRQ10
COM4, 2E8, IRQ11
configuration. (COM3
& COM4 Only for DOS
mode and Non-PnP
OS.)
None Specify the COM B
COM1, 3F8, IRQ4
COM2, 2F8, IRQ3
COM3, 3E8, IRQ10
COM4, 2E8, IRQ11
configuration. (COM3
& COM4 Only for DOS
mode and Non-PnP
OS.)
Normal (16550) Define the COM B
IrDA (HPSIR)
hardware.
ASK IR
FAST IR
DMA
Setting for
Fast IR
DMA 0 Specify the Fast IR
DMA 1
DMA configuration.
DMA 3
None Specify the LPT port
Address
LPT1, Addr 378,
and IRQ configuration.
IRQ7
LPT2, Addr 278,
IRQ5
LPT3, Addr 3BC,
IRQ7
Port
Definition
Standard AT (Centronics)
Bidirectional (PS-2)
Enhanced Parallel (EPP)
Extended Capabilities (ECP)
DMA
Setting For
ECP Mode
DMA 1 Specify the
DMA 3
ECP DMA
configuration.
EPP Type EPP 1.9 Specify the
EPP type.
Chapter 5: Installing
Drivers
Page 66
3-14
Item
Setting/Option
Function
PS/2 Mouse
Port
Enable Enable the system’s
trackpad or an external
PS/2 mouse.
Disable Disable the trackpad or
PS/2 mouse if an
external mouse is
connected to COM A
port.
Microsoft
Intellimouse
Support
Enable Support PS/2 mouse
with the wheel button.
Disable Do not support PS/2
mouse with the wheel
button.
Keyboard
Numlock
Enable Specify whether Num
Disable
Lock is on or off at
system boot time.
Keyboard
Repeat
Key Repeat
Rate
2 cps Define the rate
6 cps
10 cps
15 cps
20 cps
(characters per second)
at which the keyboard
repeats while a key is
depressed.
30 cps
Key Delay 1/4 sec Specify the amount of
1/2 sec
3/4 sec
1 sec
time (second) that will
pass after a key is
depressed before the
key starts to repeat.
TV Mode Japanese NTSC Specify the TV mode
US NTSC
selection
PAL
User's Manual
Page 67
Figure 3
-5
3-15
Components Menu
Chapter 5: Installing
Drivers
Page 68
3-16
Item
Setting/Option
Function
Power Menu
Enable Power
Saving
Low Power
Saving
Medium Power
Saving
High Power
Saving
Customize Disk Standby 5 sec The hard disk will be
Enable Enable/Disable all
Disable
Enable
Disable
Enable
Disable
Enable
Disable
10 sec
15 sec
20 sec
30 sec
Always on
power saving features.
Enable/Disable the
power saving to its
lowest which results in
max. performance but
shortest battery life.
Enable/Disable the
power saving to its
medium which results
in both moderate
performance and
battery life.
Enable/Disable the
power saving to its
highest which results
in min. performance
but longest battery life.
put on standby if it is
not accessed within
the specified period.
Hard disk power will
be restored when the
disk drive is accessed
again.
User's Manual
Global Timeout 1 min The system power will
2 min
4 min
6 min
8 min
12 min
16 min
Always on
be reduced if the
system has been idle
over the specified
period. System
power will be restored
when any system
activity is detected.
Page 69
Item
Setting/Option
Function
3-17
Suspend
Controls
Resume
Timer
Disable
Power
Button
Function
Power
On/Off
Suspend/
Resume
Suspend
Type
Suspend
to Disk
Suspend
to RAM
Powered
on
Suspend
Suspend
Timeout
1 min If the system has been idle for the
5 min
10 min
20 min
30 min
Never
Alarm
Enable Resume the system from the
Resume
Resume
Month/Day/Hour/
Minute
The power button is switched to
turn the system on or off.
The power button acts as a
suspend/resume button for
switching the system between a
working state and the suspend
mode.
Pressing the power button for
more than four seconds will
generate a power button over-ride
event to switch the system from a
working state to the Soft-Off state.
Specify the suspend mode for
power management.
specified period, the system will
enter user-defined suspend.
configured suspend mode when
resume alarm timer expires.
The system will resume at the
specified time (month, day, hour
and minute).
Chapter 5: Installing
Drivers
Page 70
3-18
Item
Setting/Option
Function
Figure 3
-6
Enable
MODEM
Ring
Resume
Enable
Battery
Low
Suspend
Advance
CPU
Controls
Doze
Enable Resume the system from STR or
Disable Disable the above.
Enable Automatically suspend the system
Disable Disable the above.
Clock
Control
Full
Mode
Mechanism
Mode
POS mode when a modem ring is
detected (which modem should
be connected to the serial port).
to disk upon a low battery
condition.
Specify the type of Processor
Clock Control.
User's Manual
Power Menu
Page 71
Item
Function
3-19
Exit Menu
Save and Exit Save the current settings and reboot the
system.
Exit (No Save) Exit without saving any current changes.
Default Settings Restore the default settings (the original ones
found in ROM).
Restore Settings Restore the current setup settings to the
original custom ones.
Version Info Show current BIOS version information.
Figure 3-7
Exit Menu
Chapter 5: Installing
Drivers
Page 72
3-20
User's Manual
Page 73
I
Appendix A: Specifications
This following are the features and specifications of the notebook computer.
Processor
− Intel® Celeron™ processors 300A/333/366/400/433 MHz
− Intel® Mobile Pentium® II / Celeron™ processors
266/300/333/366 MHz
Memory
− Two 144pins SODIMM sockets
− Supports EDO/Sync DRAM SODIMM (3.3V)
− 8/16/32/64/128 MB module (optional)
− Expendable memory up to 256MB.
System BIOS
− 256KB Flash ROM
− Systemsoft, Plug and Play 1.0a, ACPI (1.0)
Display
− SVGA flat panel 12.1” TFT
− AGP 1X
− 64-bit hardware 2D/3D Accelerator Graphics Engine
− TV-out with Marco Vision® V7.1 anti-copy technology
− 4MB display memory SGRAM type
− CRT resolution up to 1280x1024x16M
− DuoView™ display capability under Windows 98
− Support Zoomed Video Port
− Support Software MPEG II playback (option).
Storage
− 3.5” 3-mode FDD/12.7mm(h) LS-120
− DVD-ROM (12.7mm)/CD-ROM (24X speed, 12.7mmH or
9.5mmH)/CD-RW (12.7mm)
− 2.5” 12.7mm(h) HDD, support LBA mode
− Support Master mode IDE, PIO mode 4/ATA-33 (Ultra DMA)
Appendix B: I/O Port
Assignment
Page 74
II
User’s Manual
Page 75
III
Audio
− 3D stereo sound system
− Compatible Sound-Blaster PRO™ version 3.01
− IIS interface for external ZV port or MPEG audio
− Built-in microphone
− Built-in 2 speakers
− Software Wavetable
− FM music synthesizer 16 bits stereo sound system
PC Card Sockets
− Two type II (PCI) PCMCIA 3.3V/5V sockets
− Support Zoom Video Port (Socket A)/CardBus (PC Card95)
Interface
− Built-in trackpad (PS/2)
− One USB port
− One serial port
− One parallel port (LPT1), support ECP/EPP 1.7a and 1.9
− Infrared file transfer, IrDA 1.0/ASKIR
− External CRT monitor
− One S-Video jack for TV output
− One External keyboard/mouse (PS/2 type) port
− One headphone jack
− One microphone jack
− One RJ-11 jack for Plug & Play Modem Accessory (option)
− DC-in jack
Communication
− Wireless Infrared transfer, IrDA 1.0 compliant
− 56K Plug & Play Modem v.90 compliant (option)
Power Management
− Support APM v1.2
− Support ACPI v1.0
− Soft Off by system Power button
− Support suspend to disk
− Battery low suspend
− Resume from alarm time
Appendix B: I/O Port
Assignment
Page 76
IV
− Resume from modem ring (COM port only)
User’s Manual
Page 77
V
Power
− Full range AC adapter – AC in 100-240V, 47-63Hz
− Support one removable Ni-MH/Li-Ion Battery
Size & Weight
− 280mm(w)x240mm(d)x39.5mm(h)
− 2.8kg (with Lithium-Ion battery)
Keyboard
− 84 keys Win95 keyboard include numeric keypad.
Environment
− Temperature:
Operating: 5∘C~35∘C, Non-Operating: 20∘C~60∘C
− Humidity
Operating: 20%~80%, Non-Operating: 10%~90%
Optional
− 5001 Ni-MH Battery
− 5002 Li-Ion Battery
− 5002S Smart Li-Ion Battery
− 5003 DVD-ROM Drive Kit
− 5005 LS-120 MB Floppy Drive Kit
− 1008 MPEG playback kit
− 2005 Car Adapter
− 5008 56K v.90 Modem
Appendix B: I/O Port
Assignment
Page 78
VI
User’s Manual
Loading...