Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice.
Information contained herein is for reference only and does not constitute a commitment on the part
of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any
errors or inaccuracies that may appear in this publication nor are they in anyway responsible for
any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor,
manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only
and are not intended as an endorsement of that product or its manufacturer.
©August, 2001
i
User’s Manual
Trademarks
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel and Pentium are registered trademarks of Intel Corporation.
MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation.
ii
Preface
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver .
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning:
[ A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be
used. ]
[ Use only shielded cables to connect I/O devices to this equipment. ]
Y ou are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
[ ]: depend on EUT condition.
iii
User’s Manual
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or
laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a
fire. They may explode. Check with local codes for possible special disposal instructions.
IMPORTANTES MESURES DE SÉCURITÉ
iv
Certaines mesures de sécurité doivent être prises pendant l’utilisation de matérial téléphonique afin
de réduire les risques d’incendie, de choc électrique et de blessures. En voici quelquesunes:
1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire, d’un lavabo, d’un évier de
cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.
2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans fil) pendant un orage électrique.
Ceci peut présenter un risque de choc électrique causé par la foudre.
3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la
fuite.
4. Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manuel. Ne pas
jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements pertinents quant
à l’émination des piles.
Instructions for Care and Operation
As with any other piece of precision electronic equipment, proper care and operation of your notebook computer will prolong its use. Help your notebook
computer last longer by following the advice in this section:
Handling the Computer
Preface
Do not expose it to excessive heat or
direct sunlight.
Do not expose your notebook computer to any shock or vibration.
v
User’s Manual
Do not expose it to strong magnetic
fields.
Do not turn off any peripheral
devices when the computer is on.
Do not leave it in a place where
foreign matter or moisture may
affect the system.
Do not turn off the power until you
properly shutdown all programs.
vi
Preface
Do not place the computer on an
unstable surface.
Don’t use or store the computer in
a humid environment.
Do not place the computer on any
surface which will block the vents.
Do not disassemble the computer
by yourself.
vii
User’s Manual
Do not place anything heavy on the
computer.
If there is an unusual odor, heat or
smoke coming from your computer,
When traveling by air, follow the
airline’s instructions for in-flight
use.
Perform routine maintenance on
your computer.
viii
unplug the cord.
Handling of the Power Cord & Battery
Preface
Do not plug in the power cord if you
are wet.
Do not place heavy objects on the
power cord.
Do not use the power cord if it is
broken.
Do not touch the battery contacts
with your hands or any metal
objects.
ix
User’s Manual
Keep the battery away from
metal appliances.
Handling Peripheral Devices
Use only approved brands of
peripheral devices.
Affix tape to the battery contacts
before diposing of the battery.
Unplug the power cord before
attaching any peripheral devices.
x
Other Reminders
Preface
Do not throw the computer or
accessories into a fire.
Remember to periodically save your
data. Data may be lost if the bat-
Do not touch the poisonous
liquid if the LCD panel breaks.
Take periodic breaks if you are
using the computer for long peri-
tery is depleted.
ods of time.
xi
User’s Manual
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the
computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
The following are some tips to reduce the strain:
– Adjust the height of the chair and/or desk so that the keyboard is at or
slightly below the level of your elbow. Keep your forearms, wrists, and
hands in a relaxed position.
– Your knees should be slightly higher than your hips. Place your feet flat
on the floor or on a footrest if necessary.
xii
– Use a chair with a back
and adjust it to support
your lower back comfortably.
– Sit straight so that your
knees, hips and elbows
form approximately 90
degree angles when you
are working.
Remember to:
– Alter your posture frequently.
– Stretch and exercise your body several times a day.
– Take periodic breaks when you work at the computer for long periods of
time. Frequent and short breaks are better than fewer and longer
breaks.
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain
and muscle fatigue in your neck and shoulders.
Preface
– Position the display to avoid glare or reflections from overhead lighting
or outside sources of light.
– Keep the display screen clean and set the brightness and contrast to
levels that allow you to see the screen clearly.
– Position the display directly in front of you at a comfortable viewing
distance.
– Adjust the display viewing angle to find the best position.
xiii
User’s Manual
Content s
Chapter 1. Getting to Know Your Computer
Quick Start Guide ............................................................................................... 1-2
Top View with LCD Display Closed................................................................... 1-3
Top View with Display Open.............................................................................. 1-4
LCD Display.................................................................................................. 1-5
Microphone ................................................................................................... 1-5
LED Status Indicators ................................................................................. 1-5
Three Hot-key Buttons................................................................................. 1-5
Power Button ................................................................................................ 1-5
Keyboard ....................................................................................................... 1-6
xiv
Stereo Speakers ............................................................................................ 1-6
TouchPad and Buttons ................................................................................. 1-6
LED Power Indicators.................................................................................. 1-6
Right Side View .................................................................................................. 1-7
5.25" CD Device ............................................................................................ 1-7
Vent............................................................................................................... 1-7
Security Slot.................................................................................................. 1-7
Attaching a Security Lock...................................................................... 1-8
Rear View............................................................................................................ 1-9
DC-in Jack..................................................................................................... 1-9
PS/2 Type Port .............................................................................................. 1-9
Parallel Port .................................................................................................. 1-9
Phone Jack.................................................................................................. 1-10
Vent............................................................................................................. 1-10
External Monitor (CRT) Port ..................................................................... 1-10
Dual USB Ports .......................................................................................... 1-10
S-Video Connector ...................................................................................... 1-10
IEEE 1394 Port .......................................................................................... 1-11
LAN Jack .................................................................................................... 1-11
Left Side View................................................................................................... 1-12
Microphone-in Jack .................................................................................... 1-12
Speaker-out Jack ........................................................................................ 1-12
Audio Volume Control................................................................................ 1-13
PC Card Slot ............................................................................................... 1-13
Infrared Port............................................................................................... 1-13
3.5" FDD (Floppy Disk Drive)..................................................................... 1-13
Bottom View...................................................................................................... 1-14
Preface
RAM Cover ................................................................................................. 1-14
Battery Pack Cover .................................................................................... 1-14
Chapter 2. Using the Computer
The Power Sources ............................................................................................. 2-2
AC Adapter ................................................................................................... 2-2
Battery .......................................................................................................... 2-3
Recharging by AC Power....................................................................... 2-4
Proper Handling of the Battery Pack.................................................... 2-4
Turning on the Computer .................................................................................. 2-5
LED Indicators ............................................................................................. 2-5
LED Power Indicators............................................................................ 2-6
xv
User’s Manual
LED Status Indicators ........................................................................... 2-7
The Hard Di sk Drive ( HDD)............................................................................... 2-8
Removing the HDD Module ......................................................................... 2-8
Inserting the HDD Module ........................................................................ 2-10
Replacing the HDD..................................................................................... 2-11
The Floppy Disk Drive (FDD) .......................................................................... 2-13
Inserting and Removing Diskettes............................................................ 2-13
The CD Device .................................................................................................. 2-14
Loading CDs or DVDs ...................................................................................... 2-14
Handling CDs or DVDs .............................................................................. 2-15
The PC Card Slot.............................................................................................. 2-16
Inserting PC Cards .................................................................................... 2-16
Removing PC Cards ................................................................................... 2-16
PC Card Problem in Windows 98 .............................................................. 2-17
Hot Keys ............................................................................................................ 2-18
xvi
Three Hot-Key Buttons .............................................................................. 2-18
Programming the Hot Keys ....................................................................... 2-19
Function Keys................................................................................................... 2-20
The Numeric Keypad........................................................................................ 2-21
Chapter 3. Power and Battery Information
Power Management ............................................................................................ 3-1
Advanced Configuration and Power Interface (ACPI) ............................... 3-1
Advanced Power Management (APM 1.2) .................................................. 3-1
Conserving Power through Individual Components: ................................. 3-2
Hard Disk Standby ................................................................................. 3-2
Monitor Standby..................................................................................... 3-2
Conserving Power throughout the Whole System:..................................... 3-2
Suspend and Resume ................................................................................... 3-2
A: Standby ............................................................................................... 3-2
B: Hibernate............................................................................................ 3-3
Setting the Power Management Functions ................................................ 3-4
Creating a Partition on Your Hard Drive ............................................. 3-5
Battery Information ........................................................................................... 3-6
New Battery:................................................................................................. 3-6
Battery Life:.................................................................................................. 3-6
Battery FAQ ................................................................................................. 3-6
Conserving Battery Power ........................................................................... 3-7
Removing the Battery........................................................................................ 3-8
Chapter 4. Upgrading the Computer
Upgrading the Memory...................................................................................... 4-2
Preface
A: Removing a Memory Module .................................................................. 4-3
B: Installing a Memory Module................................................................... 4-5
C: Setting the SW6 Jumper Switch ............................................................. 4-6
Upgrading the Processor.................................................................................... 4-8
Upgrading the Hard Disk................................................................................... 4-8
Chapter 5. BIOS Utilities
Power On Self Test (POST) ................................................................................ 5-2
POST Message: Normal Operation.............................................................. 5-2
POST Message: Error Detected ................................................................... 5-3
System Configuration Utility ............................................................................ 5-4
xvii
User’s Manual
Information in the System
Configuration Utility (SCU) ........................................................................ 5-4
Initiating the System Configuration Utility............................................... 5-5
Working with the Menu Bar........................................................................ 5-6
Working with the Pull-down Menu ....................................................... 5-7
System Configuration Utility Options ........................................................ 5-8
Startup Menu .......................................................................................... 5-8
Memory Menu ....................................................................................... 5-11
Disks Menu ........................................................................................... 5-12
Components Menu ................................................................................ 5-13
Power Menu .......................................................................................... 5-16
Exit Menu ............................................................................................. 5-18
SCU Screen Samples .................................................................................. 5-19
Startup Screen...................................................................................... 5-19
Memory Screen ..................................................................................... 5-19
xviii
Disks Screen.......................................................................................... 5-20
Components Screen .............................................................................. 5-20
Power Screen ........................................................................................ 5-21
Exit Screen ............................................................................................ 5-21
Chapter 6. Driver Installation
Before Installing Windows................................................................................. 6-2
Partitioning the HDD............................................................................. 6-2
Formatting the HDD .............................................................................. 6-2
Installing Windows 98 SE (for reference only) ................................................. 6-3
Installing Windows Me (for reference only) ...................................................... 6-4
Installing Windows 2000 (for reference only) ................................................... 6-5
Installing Drivers in Windows 98 SE ................................................................ 6-7
Step 1: Installing the Audio Driver ............................................................. 6-7
Step 2: Installing the Video Driver.............................................................. 6-8
Step 3: Installing the Hot Key Driver.......................................................... 6-8
Step 4: Installing the LAN Driver ............................................................... 6-9
Step 5: Installing the PCMCIA Driver (Optional)...................................... 6-9
Step 6: Installing the Modem Driver (Optional) ....................................... 6-10
Installing Drivers in Windows Me................................................................... 6-12
Step 1: Installing the Audio Driver ........................................................... 6-12
Step 2: Installing the Video Driver............................................................ 6-13
Step 3: Installing the Hot Key Driver........................................................ 6-13
Step 4: Installing the LAN Driver ............................................................. 6-14
Step 5: Installing the Modem Driver (Optional) ....................................... 6-14
Installing Drivers in Windows 2000................................................................ 6-16
Step 1: Installing the SiSIDE Utility ........................................................ 6-16
Preface
Step 2: Installing the Audio Driver ........................................................... 6-16
Step 3: Installing the Video Driver............................................................ 6-16
Step 4: Installing the Hot Key Driver........................................................ 6-17
Step 5: Installing the LAN Driver ............................................................. 6-17
Step 6: Installing the Modem Driver (Optional) ....................................... 6-18
Installing Drivers in Windows NT4.0 ............................................................. 6-20
Step 1: Installing the Audio Driver ........................................................... 6-20
Step 2: Installing the Video Driver............................................................ 6-20
Step 3: Installing the Hot Key Driver........................................................ 6-21
Step 4: Installing the LAN Driver ............................................................. 6-21
Step 5: Installing the Modem Driver (Optional) ....................................... 6-22
xix
User’s Manual
Chapter 7. Troubleshooting
Audio ............................................................................................................. 7-2
Battery .......................................................................................................... 7-2
Boot Password............................................................................................... 7-4
CD.................................................................................................................. 7-4
Floppy Disk Drive (FDD).............................................................................. 7-6
Hard Disk Drive (HDD) ................................................................................ 7-7
Hardware Installation.................................................................................. 7-7
LCD Panel ..................................................................................................... 7-8
Microphone-in Jack ...................................................................................... 7-8
Memory Module............................................................................................ 7-9
PC Card ....................................................................................................... 7-10
Power........................................................................................................... 7-10
Printer......................................................................................................... 7-11
xx
Appendix A. Specifications
Glossary
Getting to Know Your Computer
Chapter 1. Getting to Know Your Computer
In this chapter you will become familiar with the basic functions and components of your notebook computer and possibilities for expansion.
This chapter includes:
• Quick start guide
• Views
!!
!
!!
Note
This manual
refers to the two
notebook models pictured on
this page.
The models
vary slightly in
external design.
Photos used
throughout this
manual are of
Model A.
1
Model A Model B
1 - 1
User’s Manual
1
!!
!
!!
Note
Be sure to keep
the packing
materials in a
safe place in
case you need
them for shipping or longterm storage.
!!
!
!!
Note
Devices which
connect to the
USB and
IEEE 1394
ports can be
connected after
Windows is up
and running.
All other devices must be
connected
before you turn
on the system.
Quick Start Guide
This quick start guide assumes that you’re already familiar with notebook computers and can tell at a glance what and where all the key components are.
If you’re not that comfortable with this sort of device, take a look at the following
pages for an overview of the system.
In any case, you should review these steps, before you take any action. If you
aren’t sure about one of the procedures, check the relevant chapter before continuing.
Unless you have to install an operating system, your computer is ready to work
right out of the box.
But, before you begin, follow the safety instructions in the Preface, especially
the instruction on placement.
1. Remove all packing materials, CDs/DVDs, floppy disks and any PC Cards.
2. Securely attach any peripherals you want to use with the notebook (e.g.
mouse and keyboard) to their ports.
3. Attach the AC adapter to the DC-in jack on the computer’s rear, plug the
AC power cord into an outlet and then connect the AC power cord to the AC
adapter.
4. Raise the lid/LCD to a comfortable viewing angle (page 1-3).
5. Push the power button to turn “on”.
1 - 2
Getting to Know Your Computer
Top View with LCD Display Closed
To open the LCD display:
1) Place the computer on a stable surface.
2) Move the cover latch to the right to release the top cover.
3) Lift the top cover to reveal the LCD panel and keyboard.
4) Adjust the LCD panel to a comfortable viewing angle.
1
1. Cover Latch
1
figure 1-1
1 - 3
User’s Manual
1
Top View with Display Open
1. LCD Display
2. Microphone (built-in)
3. LED Status Indicators
4. Three Hot-Key Buttons
5. Power Button
6. Keyboard
7. Stereo Speakers
8. TouchPad and Buttons
9. LED Power Indicators
1
3
4
2
5
1 - 4
figure 1-2
6
7
8
9
7
Getting to Know Your Computer
LCD Display
The Notebook comes with a TFT LCD (Liquid Crystal Display) display.
Depending on the model and configuration you have purchased, the display can be either a 13.3” or 14.1” XGA TFT color panel.
Microphone
Record on your notebook computer with this built-in microphone.
LED Status Indicators
Display the system's operational status. Refer to Chapter 2 for more
information.
Three Hot-key Buttons
!!
!
!!
Note
After turning
the computer off
wait at least 5
seconds before
turning it on
again.
1
Three hot keys give you easy access to the Internet, e-mail and an application of your choice. To learn how to set the buttons refer to Chapter 2.
Power Button
Press this button to turn your notebook computer on or off. The Power
Button can also be used as a Suspend/Resume button when pressed less
than four seconds (if configured appropriately in the System Configuration Utility, refer to Chapter 5 for more details).
1 - 5
User’s Manual
1
Keyboard
An A4-Size Win98 keyboard with an embedded numeric keypad. It has
many of the same features as a full-sized desktop keyboard and can easily
be replaced with a non-English keyboard should you desire.
Stereo Speakers
Two built-in speakers provide rich, stereo sound.
TouchPad and Buttons
The pointing device features a sensitive glide pad for precise movements.
It functions the same way as a two-button mouse: the right TouchPad
button is the same as the right mouse button; the left TouchPad button is
the same as the left mouse button.
1 - 6
LED Power Indicators
Display the current power source and power source status of the computer.
For more information please refer to Chapter 2.
Getting to Know Your Computer
Right Side View
1
1. 5.25” CD Device 2. Vent 3. Security Slot
5.25" CD Device
Depending on the configuration you purchased, your notebook may come
with one of the following 12.7mm CD devices: 24X-speed CD-ROM drive,
8X-speed DVD-ROM drive, CD-RW drive (20X Read, 8X Write) or DVD-
1
3
2
figure 1-3
!!
!
!!
ROM+CD-RW combo drive.
Vent
Enables airflow to prevent the notebook from overheating.
Security Slot
To prevent possible theft a lock can be attached to this slot. Locks can be
purchased at any computer store.
Warning
To prevent your
computer from
overheating,
make sure
nothing blocks
the vent while
the computer is
in use.
1 - 7
User’s Manual
1
Attaching a Security Lock
To install the security lock, wrap the cable around a desk or other immovable
object, then insert the locking device into the slot located on the right side of the
computer.
1 - 8
Security Lock Cable
Security Lock
figure 1-4
Getting to Know Your Computer
Rear View
2
1
1. DC-in Jack
2. PS/2 Type Port
3. Parallel Port
4. Phone Jack
DC-in Jack
Plug the supplied AC adapter into this jack to power your notebook.
1
4
3
5
6
5. Vent
6. External Monitor
(CRT) Port
7. Dual USB Ports
7
8
10
9
figure 1-5
8. S-Video Connector
9. IEEE 1394 Port
10. LAN Jack
PS/2 Type Port
To connect an external PS/2 type mouse or keyboard.
Parallel Port
This parallel port supports ECP (Extended Capabilities Port) and EPP
(Enhanced Parallel Port) 1.7/1.9 modes.
1 - 9
User’s Manual
1
!!
!
!!
Warning
To prevent your
computer from
overheating,
make sure
nothing blocks
the vent while
the computer is
in use.
Phone Jack
Supports the optional modem module.
Vent
Enables airflow to prevent the notebook from overheating.
External Monitor (CRT) Port
Connect an external CRT monitor to this port to allow simultaneous display on the LCD display and external CRT monitor.
Dual USB Ports
A hardware interface for low-speed peripherals such as the keyboard,
mouse, joystick, scanner, printer and telephony devices. It allows every-
1 - 10
thing to be plugged in and unplugged without turning the system off
S-Video Connector
Connect your television to your computer and view DVD’s, VCD’s or anything else your computer can display. You will need an S-Video cable to
make the connection which is easily found at any audio or computer store.
Getting to Know Your Computer
IEEE 1394 Port
Allows high speed connection to various peripheral devices, such as an
external disk drive or a digital camera.
LAN Jack
Supports the integrated LAN function.
!!
!
!!
Note
Your notebook
will only accept
IEEE 1394
devices which
have their own
power source.
1
1 - 11
User’s Manual
1
!!
!
!!
Note
The S/PDIF
output feature
is available only
in Windows 98
and Windows
Me.
Refer to Chapter 6 for installation instructions and settings.
Left Side View
1 2
3
1. Microphone-in Jack
2. Speaker-out Jack
3. Audio Volume Control
Microphone-in Jack
A microphone can be connected to your notebook via this jack. You can
also use this for S/PDIF (Sony/Philips Digital Interface Format) output,
which allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver giving you surround sound. To switch from microphonein to S/PDIF output or S/PDIF output to microphone-in, you will need to
use the SCU. Refer to the Startup Menu in Chapter 5 for information.
Speaker-out Jack
Headphones or speakers can be connected through this jack.
5
6
4
figure 1-6
4. PC Card Slot
5. Infrared Port
6. 3.5” FDD (Floppy Disk Drive)
1 - 12
Getting to Know Your Computer
Audio Volume Control
Adjust the audio volume with this knob. Audio volume can also be adjusted in the operating system.
PC Card Slot
A Type-II PC card slot which also supports CardBus mode. Refer to
Chapter 2 for more information on the PC Card slot.
Infrared Port
Allows wireless communications with an infrared-compatible device. The
Infrared port supports IrDA (HPSIR) 1.1, FIR and ASKIR (Sharp standard) modes. For further information, please refer to the manual of the
infrared device you wish to connect.
1
3.5" FDD (Floppy Disk Drive)
A 3.5”, 3-mode, 1.44 MB fixed floppy disk drive. For more information on
using the floppy disk drive, please refer to Chapter 2.
1 - 13
User’s Manual
1
Bottom View
1
2
1 - 14
figure 1-7
1. RAM Cover 2. Battery Cover
RAM Cover
The cover secures the installed RAM modules. For further information on
removing or inserting the RAM modules, please refer to Chapter 4.
Battery Pack Cover
The cover secures the battery pack in its bay.
Chapter 2. Using the Computer
Your notebook computer can be used almost anywhere, in the home, office, or on
Using the Computer
the road. To learn more about your computer, please read this chapter.
This chapter includes:
– The Power Sources
– Turning on the Computer
– The Hard Disk Drive
– The Floppy Disk Drive
– The CD Device
– The PC Card Slot
– The Hot Keys
– The Numeric Keypad
2
2 - 1
User’s Manual
The Power Sources
The computer can be powered by either an AC adapter or a battery pack de-
2
pending on where you want to use it.
AC Adapter
Use only the AC adapter that comes with your computer. An incorrect type of
AC adapter will cause damage to the computer and its components.
1) Plug the AC adapter cord into the DC-in jack on the rear panel of the computer.
2) Plug the power cord into a
properly grounded
outlet.
3) Connect the AC
adapter with the
2 - 2
power cord.
figure 2-1
Battery
The battery allows you to use your notebook computer while you are on the
Using the Computer
road or an electrical outlet is unavailable. Battery life varies depending on the
applications and the configuration you're using. To increase battery life, let the
battery discharge completely before recharging.
We recommend leaving the battery inside the notebook at all times. For more
information on the battery, please refer to Chapter 3.
1. Battery Cover
!!
!
!!
Note
Don’t remove
the battery pack
from the computer unless it
is damaged and
needs to be
replaced.
2
figure 2-2
1
2 - 3
User’s Manual
2
Recharging by AC Power
The battery pack automatically recharges when plugged into an electrical outlet. If the computer is powered on and in use it will take several hours to fully
recharge the battery. When the computer is turned off but plugged into an
electrical outlet, battery charge time is less. (Refer to LED Power Indicators in
this chapter for information on the battery charge status.)
Proper Handling of the Battery Pack
- DO NOT disassemble the battery pack under any circumstances.
- DO NOT expose the battery to fire or high temperatures, it may explode.
- D O NOT connect the metal terminals (+, -) together . (For more information on how
to maintain the battery pack, refer to Chapter 3.)
2 - 4
Turning on the Computer
Now you are ready to begin using your new notebook computer. To turn it on
Using the Computer
simply press the power button on the top right of the front panel (figure 2-3) .
The power button can also be used as a Suspend/Resume hot-key button if
pressed less than four seconds and appropriately configured in the SCU.
(Please refer to Chapter 5, BIOS Utilities, for
more information.)
Power
Button
2
figure 2-3
LED Indicators
There are two sets of LED indicators (LED Power Indicators and LED Sta-
tus Indicators) on your computer that will display helpful information about
the current status of the computer.
2 - 5
User’s Manual
LED Power Indicators
2
!!
!
!!
Note
When the battery is critically
low, immediately connect
the AC adapter
to the computer
or save your
work; otherwise,
the unsaved
data will be lost
when power is
depleted.
LED Power Indicatorsfigure 2-4
nocI
roloC noitpircseD
neerG.nodenrutsiretupmocehT
neerGgniknilB
wolleY.llufsirewopyrettabronideggulpsirewopCA
.edom
dnepsusderugifnocehtderetnesahmetsysehT
2 - 6
thgiloN
wolleYgniknilB.degrahcgniebsiyrettabehT
sirewopyrettabrodesugniebsirewopCA
.lamron
wolleYgniknilBwolyllacitircsirewoPyrettaB
table 2-1
LED Status Indicators
Once your computer is on and in use, the
Using the Computer
LED status indicators will display the
system's operational status.
nocI roloC noitpircseD
neerG.desseccagniebsievirdksidyppolF
neerG.desseccagniebsiecivedDC/ksiddrahehT
figure 2-5
!!
!
!!
Note
To enable/
disable the
Scroll Lock
feature, press
the Fn and Scr
Lk key simultaneously.
2
neerG.detavitcasikcoLmuN
neerG.detavitcasikcoLspaC
neerG.detavitcasikcoLllorcS
table 2-2
2 - 7
User’s Manual
The Hard Disk Drive (HDD)
The hard disk drive is used to store your data internally in the notebook com-
2
!!
!
!!
Warning
Before remov-
ing the HDD,
please check
with your
dealer to find
out if this will
VOID your
warranty.
puter. It is mounted in a removable case and can be taken out to accommodate
other 2.5” IDE hard disk drives with a height of 9.5 mm or 12.7 mm. The system supports DMA mode 2, PIO mode 4, and ATA-33/ATA-66/ATA-100 IDE
HDDs.
Removing the HDD Module
1) Turn off the computer.
2) Press the four keyboard latches at the top of
the keyboard to elevate the
keyboard from its normal
position (figure 2-6)
2 - 8
figure 2-6
""
""
"
3) Carefully raise and set the keyboard aside and
locate the HDD module (figure 2-7a).
4) Unscrew the 3 screws (A, B, C) holding the
HDD module on the mainboard (figure 2-7b) .
5) Lift the HDD module out of the computer by
pulling on the HDD tab (figure 2-8).
B
Using the Computer
2
A
C
figure 2-7b
1. HDD
2. HDD Tab
3. HDD Connector
""
"
""
figure 2-7a
2
3
1
figure 2-8
2 - 9
User’s Manual
Inserting the HDD Module
(with no HDD module currently installed)
2
1) Place the HDD module into the computer in its appropriate spot, making
sure to align the HDD connector with the socket on the mainboard (figure
2-9).
2) Connect the HDD connector securely to the mainboard by gently pressing
the HDD module on to the mainboard.
3) Insert and tighten the 3 screws which hold the HDD module on the
mainboard.
4) Reinstall the keyboard.
2
1
3
2 - 10
4
1. HDD
2. HDD Tab
3. HDD Connector
figure 2-9
4. HDD Socket on Mainboard.
Replacing the HDD
1) Remove the HDD module (refer to Removing the HDD Module on
pages 2-8 to 2-9 for details).
2) Remove the two screws on the HDD connector board.
3) Gently disconnect the HDD connector board from the HDD being careful
not to bend any pins.
4) Remove the two screws on each
side of the case.
5) Slowly remove the HDD from
the case.
6) Place a new HDD into the
case.
Connector Board
Using the Computer
!!
!
!!
2
Warning
Before remov-
ing the HDD,
please check
with your
dealer to find
out if this will
VOID your
warranty.
7) Hold the HDD firmly in
place with two screws on
each side.
HDD Case
HDD
figure 2-10
2 - 11
User’s Manual
2
8) Attach the HDD connector board to the HDD being careful not to bend any
pins.
9) Screw the HDD connector board on to the HDD.
10) Place the HDD module into the computer (refer to Inserting the HDD
Module on page 2-10 for details).
2 - 12
The Floppy Disk Drive (FDD)
The computer is equipped with a fixed 1.44 MB, 3.5” floppy disk drive module.
Using the Computer
It is usually designated drive A by default and can be used as a boot device if
properly set in the SCU (please refer to Chapter 5, BIOS Utilities).
Inserting and Removing Diskettes
When using the floppy drive, always insert your
floppy diskette with the label-side facing up. To
remove the inserted diskette, press the eject
button on the top-right corner of the floppy
drive.
2
figure 2-11
Eject Button
2 - 13
User’s Manual
!!
!
!!
The CD Device
The CD device can be a CD-ROM, DVD-ROM, CD-RW or DVD-ROM+CD-RW
2
Warning
When manually
ejecting a CD/
DVD, DO NOT
use a sharpened
pencil or similar object that
may break and
become lodged
in the hole.
combo module depending on the configuration you purchased. It is usually
labeled drive D and may be used as a boot device if properly set in the SCU
(please refer to Chapter 5, BIOS Utilities).
Loading CDs or DVDs
To insert a CD/DVD, press the open button and carefully place a disc onto the
disc tray with label-side facing up (see below). Push the disc tray in and you are
ready to start. The busy indicator will light up while data is being accessed or
while an audio CD is playing. If power is unexpectedly interrupted, insert an
object such as a straightened paper clip into the emergency eject hole to open
the tray.
2 - 14
figure 2-12
1
DVD Tray
1. Disc Tray
2. Busy Indicator
3
2
4
3. Open Button
4. Emergency Eject Hole
CD Tray
3
2
4
Handling CDs or DVDs
Proper handling of your CDs/DVDs will prevent them from being damaged.
Using the Computer
Please follow the advice listed below to make sure that the data stored on your
CDs/DVDs can be accessed.
Remember to:
- Hold the disc by the edges; do not touch the surface of the disc.
- Use a clean, soft, dry cloth to remove dust or fingerprints.
- Do not write on the surface with a pen.
- Do not attach paper or other materials to the surface of the disc.
- Do not store or place the disc in high-temperature areas.
- Do not use benzene, thinner, or other cleaners to clean the disc.
- Do not bend the disc.
- Do not drop or subject the disc to shock.
2
2 - 15
User’s Manual
The PC Card Slot
The computer is equipped with one PC card slot (previously referred to as
2
PCMCIA). The slot can support either one 3.3V/5V type II PC card or one 3.3V
CardBus card (PC Card 95).
Inserting PC Cards
Align the PC card with the slot and push the card in until it locks into place.
Removing PC Cards
To remove a PC card, simply press the eject button next to the slot.
1. Eject Button
2 - 16
2. PC Card Partially
Inserted in Slot
1
2
figure 2-13
PC Card Problem in Windows 98
Using the Computer
After installation of Windows 98 or Windows 98 Second Edition,
you may find that the PC cards are not working normally and you
may have noticed one or more of the following:
- An exclamation mark appears in the PC card driver in
Device Manager
- PC cards don’t work at all
- PC card controllers are not enumerated
- PC card controllers are disabled on power-up
- PC card controllers are disabled when you resume the
computer from Suspend mode
This is a problem caused by Microsoft Windows 98 (Second Edition). To resolve the problem, immediately after installing Windows 98SE install the program file PCI.vxd to update your sys-
2
tem driver. The PCI.vxd driver is supplied by your computer
dealer.
For more information on this, refer to the Microsoft article
“CardBus Device Not Enumerated with TI 14xx or 44xx CardBus
Controllers” (Article ID Q233017) which can be found on
Microsoft’s web site.
2 - 17
User’s Manual
Hot Keys
The computer provides you
2
with two sets of hot keys: three
hot-key buttons on the computer and the function key
combinations on the keyboard.
figure 2-14
Three Hot-Key Buttons
The computer offers three hot-key buttons for quick one button access to the
Internet, e-mail or a user-defined application. To use the user-defined hot key,
you need to install the Hot-Key driver. Refer to Chapter 6 for driver installation steps.
yeKtoH noitcnuF
.xobliam-eehtetavitcA
2 - 18
.resworbtenretniehtetavitcA
rof,noitacilppadeificeps-resuehtetavitcA
.lecxErodroWtfosorciMeht,elpmaxe
table 2-3
Programming the Hot Keys
After installing the hot key driver, you may have to configure or change the
Using the Computer
driver settings. To configure the driver, right click the Hot key driver icon on
the task bar and the following menu will appear.
Hot-key Driver Menu
To program the user-defined hot key, you must configure “Application 1.”
To configure and specify an application for Application 1, you must:
2
1) Select Application 1 and press Enter. A dialog box will appear on the
screen.
2) Go to the directory where the desirable application program exists
3) Click on the program file.
4) Choose Open.
The hot key is now set to execute that program.
2 - 19
User’s Manual
2
Function Keys
syeK noitpircseD
On the bottom-left of
the keyboard is the
Fn key or Function
key. The Fn key
allows you to change
operational features
instantly. To use the
following functions,
press and hold the Fn key; then press the appropriate function key
(Esc, F3, F5, etc....) located at the top of your keyboard.
csE+nFetatsemuser/dnepsusneewtebelggoT
3F+nFyalpsidDCLdnapxE
5F+nFffo/nooiduanruT
6F+nFTRCdnaDCL/DCL/TRCneewtebelggoT
9F+nFssenthgirbDCLesaerceD
01F+nFssenthgirbDCLesaercnI
table 2-4
2 - 20
figure 2-15
The Numeric Keypad
The keyboard has an embedded numerical keypad for easy numeric data input.
Using the Computer
The keypad stands out by its blue typeface.
To use the keypad simply:
• Activate the Num Lock feature by pressing the Num Lock key.
• Press Fn + the desired number keys.
2
figure 2-16
2 - 21
Notes:
Power and Battery Information
Chapter 3. Power and Battery Information
Power Management
To conserve power, especially when using the battery, your notebook computer
has two types of power management available; ACPI and APM.
Advanced Configuration and Power Interface (ACPI)
The ACPI interface provides the computer with enhanced power saving techniques and gives the operating system (OS) direct control over the power and
thermal states of devices and processors. For example, it enables the OS to set
devices into low-power states based on user settings and information from applications. ACPI is available in Windows 98, Windows 98SE, Windows Me and
Windows 2000. ACPI is the more recent of the two power management types
!!
!
!!
Note
Power management functions
will vary
slightly depending on your
operating system. For more
information it
is best to refer
to the user’s
manual of your
operating system.
3
available and the one you use with a Windows operating system.
Advanced Power Management (APM 1.2)
APM is an older type of power management which is set in the system BIOS,
currently APM is available on this machine for users who are interested in
running DOS or Linux.
Power management conserves power by controlling individual components of
the computer (the monitor and hard disk drive) or the whole system.
!!
!
!!
Note
Information on
setting the
APM options
can be found in
Chapter 5,
Power Menu.
3 - 1
User’s Manual
!!
!
!!
Conserving Power through Individual Components:
Hard Disk Standby
3
Note
Hard Disk
Standby can be
set in the SCU
and the operating system you
are using. The
SCU settings
will override the
operating system settings.
!!
!
!!
Note
To learn more
about power
management
settings in the
SCU, refer to
Chapter 5,
Power Menu.
The computer's hard disk drive motor will be turned off if the hard disk drive
has not been accessed for a specified period of time. If the system reads or
writes data, the hard disk motor will be turned back on. You can set this in the
control panel of your OS or in the SCU.
Monitor Standby
To conserve power, you can set the monitor to turn off after a specified time.
This is done in the operating system.
Conserving Power throughout the Whole System:
Suspend and Resume
With this function you can stop the notebook’s operation and restart where you
left off. This system features two suspend mode levels:
A: Standby
B: Hibernate
A: Standby
3 - 2
Standby saves the least amount of power, but takes the shortest time to return
Power and Battery Information
to full operation. During Standby the hard disk is turned off, and the CPU is
made to idle at its slowest speed. All open applications are retained in memory.
When you are not using your computer for a certain length of time, which you
specify in the operating system, it will enter Standby mode to save power.
The system can resume from Standby mode by:
· Pressing any keyboard key
3
· Pressing the power button
· An incoming call to your modem
· Alarm resume is enabled and expires
B: Hibernate *
Hibernate uses no power and saves all of your information on a part of the
HDD. It saves the maximum power but takes the longest time to return to full
operation. You can set your notebook to automatically enter Hibernate mode
when the battery power is almost depleted. This prevents losing any data due
to loss of power.
The system will resume from Hibernate mode by:
· Pressing the power button
*
If you are using
Windows 98 or
Windows 98SE
you must first
create a parti-
tion on your
hard drive in
order to use this
power manage-
ment function.
Information is
available in
table 3-1 on
page 3-5.
· Alarm resume (month/day/hour/minute)
3 - 3
User’s Manual
Setting the Power Management Functions
You can set the power management functions either in the SCU (for APM and
hard disk standby), or the operating system (for ACPI). To learn more about
what power management settings are available and how to configure them it is
3
best that you refer to your operating system’s user guide.
For more information on setting the hard disk standby or any other power
management functions in the SCU (for users of APM), please refer to the Power
Menu in Chapter 5.
If both the Windows OS power management settings and the SCU power management settings are configured, The Windows OS power management
settings will override those set in the SCU EXCEPT for hard disk
standby.
3 - 4
Power and Battery Information
Creating a Partition on Y our Hard Drive
To use Suspend to Disk or Hibernate with Windows 98 or Windows
98SE , you must create a partition on your hard disk drive (HDD). The
instructions are as follows:
Attention: You must partition your hard drive prior to installing the operating system.
While in DOS mode:
1) Use the FDISK program to delete all hard disk partitions if any already exist on the drive.
2) Go to Drive A: or the CD-ROM drive depending on the location of the
0VMAKFIL file (the file comes with the enclosed utilities CD but you
can copy it to a floppy disk if you prefer working with the floppy
drive).
3) Execute the file as follows
:\>0VMAKFIL -Pn
n must be the amount of RAM you already have or intend to
have.
table 3-1
!!
!
!!
Warning
If you increase
the system
memory to a
value larger
than your
partition you
must
repartition the
HDD.
!!
!
!!
Note
3rd Party software may be
available which
allows you to
partition or
increase the
partition size of
your HDD after
the operating
system has been
installed. Check
the documentation carefully.
3
3 - 5
User’s Manual
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
New Battery:
3
Always use a new battery before recharging it.
Battery Life:
Battery life may be shortened through improper maintenance. To optimize the life and improve the performance of your battery, fully discharge
and recharge the battery at least once every 30 days.
Battery FAQ
How do I completely discharge the battery ?
Use the computer with battery power until it shuts down due to a low
battery. Don’t turn off the computer by yourself even when you see a
message or hear beeps that indicate the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
3 - 6
How do I fully charge the battery ?
When charging the battery, don’t stop until the LED charging indicator
light stops flashing.
How do I maintain the battery ?
Completely discharge and charge the battery at least once every 30 days
or after about 20 partial discharges.
Power and Battery Information
Conserving Battery Power
Display brightness
The LCD display consumes a lot of power, so setting the brightness level
to low will save power.
Applications and external devices
Different applications and external devices consume battery power even
when they are not being used.
To conserve battery power we recommend:
· Closing modem or communication applications when they are not
being used.
· Removing any unused PC Cards from the computer. PC Cards quickly
use up battery power even if the system enters Suspend mode.
3
· Removing any unnecessary external devices from the computer.
3 - 7
User’s Manual
Removing the Battery
We recommend that you don’t
3
!!
!
!!
Caution
Danger of explosion if battery is
incorrectly
replaced. Re-
place only with
the same or
equivalent type
recommended
by the manufacturer. Dispose of
used batteries
according to the
manufacturer’s
instructions.
remove the battery, but if it is
necessary, please contact your
service representative for assistance. The removal procedure is
as follows:
1) Remove the two screws holding the battery lock in place.
2) Remove the battery cover.
3) Disconnect the battery from
the main computer.
4) Slide the battery out.
3
1
2
figure 3-1
1
3 - 8
1. Screw Holes
2. Battery Cover
3. Battery Connector Socket
4. Battery Connector
5. Battery
4
5
figure 3-2
Chapter 4. Upgrading the Computer
This chapter contains the information on upgrading the computer. Follow the
steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your dealer for further help. Before you begin you will
need:
- A small crosshead or Philips screwdriver
Upgrading the Computer
- A small regular screw driver
- An antistatic wrist strap
Before working with or repairing the internal components you will need to wear
an antistatic wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
– Upgrading the Memory
– Upgrading the Processor
– Upgrading the Hard Disk
4
4 - 1
User’s Manual
!!
!
!!
Upgrading the Memory
The computer has two memory sockets for 144-pin Small Outline Dual In-line
4
Note
If you are using
two memory
modules in your
computer we
strongly recommend using
memory modules of the same
size.
!!
!
!!
Note
If you are using
2 memory modules, they must
be of the same
type, either both
must be PC-100
or both must be
PC-133.
Memory Modules (SO-DIMM) and supports both PC-100/PC-133 SDRAM. The
main memory can be expanded up to 1 GB with one or two memory modules
using the different combinations listed below:
1knaB
)tib46(
BM23ytpme
BM23BM23BM46
BM46ytpmeBM46
BM46BM46BM821
BM821ytpmeBM821
BM821BM821BM652
BM652ytpmeBM652
BM652BM652BM215
BM215ytpmeBM215
BM215BM215BG1
2knaB
rewoP eziSlatoT
)tib46(
BM23
V3.3
table 4-1
4 - 2
The total memory size is automatically detected by the POST routine once you
turn on your computer.
To upgrade the memory in your notebook please perform the following steps:
A: Removing a memory module (if present).
B: Inserting a new memory module.
C: Setting the SW6 jumper switch.
– Removing the keyboard.
– Locating and setting the SW6 jumper switch.
Upgrading the Computer
– Replacing the keyboard.
A: Removing a Memory Module
1) Turn off the computer.
2) Turn the computer over.
3) Unscrew and remove the RAM
cover (figure 4-1).
4
1
figure 4-1
1. RAM Cover
4 - 3
User’s Manual
4) Locate the memory sockets.
5) Gently pull the two latches outward
on the sides of the memory socket
(figure 4-2).
2
4
1. Memory Module
2. Memory Socket
3. Latches
6) The module will pop up.
7) Remove the memory module as
shown (figure 4-3)..
3 3
1
figure 4-2
4 - 4
figure 4-3
B: Installing a Memory Module
1) Turn off the computer.
Upgrading the Computer
!!
!
!!
2) Turn the computer over.
3) Unscrew and remove the RAM cover (fig-
ure 4-1).
4) Insert the memory module at a slight angle
about 45° and fit its connectors firmly into
the memory slot (figure 4-5).
2
1
figure 4-4
1. Memory Connectors
2. Memory Socket
Note
Make sure the
memory connectors go into the
memory socket
when you are
installing the
memory modules.
4
figure 4-5
5) Press down on the two edges of the
memory module and lock it into place
(figure 4-6).
6) Reinstall the RAM cover.
figure 4-6
4 - 5
User’s Manual
!!
!
!!
C: Setting the SW6 Jumper Switch
1) Turn off the computer.
4
Note
Step C is only
necessary if
your new
memory module
is a different
type than your
previous one.
If the previous
memory module
was a PC-100
and the new
module is a PC133 or viceversa, then you
must proceed
with Step C.
Otherwise skip
this Step.
2) Remove the keyboard by pressing the 4 latches at the top (figure 4-7) and
gently lifting it out of the notebook.
3) Place the keyboard as shown
(figure 4-8).
1
figure 4-7
4 - 6
figure 4-8
1. SW6 Jumper Switch
4) Locate the SW6 jumper switch
(figure 4-8) or (figure 4-9).
5) Set the SW6 jumper switch according to table 4-2.
SW6 Jumper Switch Settings
UPC MARDS 1-6WS 2-6WS 3-6WS 4-6WS 5-6WS 6-6WS
1
1. SW6 Jumper Switch
Upgrading the Computer
4
figure 4- 9
66331-CPFFOFFOFFOFFONONO
66001-CPFFOFFOFFOFFONOFFO
001001-CPNOFFOFFOFFONOFFO
001331-CPNOFFONOFFONOFFO
331331-CPNONONOFFONOFFO
6) Reinstall the keyboard.
table 4-2
4 - 7
User’s Manual
Upgrading the Processor
If you want to upgrade your computer by replacing the existing processor with
a faster one you will need to contact your customer service representative. We
recommend that you do not attempt to do this yourself since if done incorrectly
you may damage the processor or mainboard.
4
Upgrading the Hard Disk
Please refer to pages 2-8 ~ 2-12 for instructions on upgrading the hard disk.
4 - 8
Chapter 5. BIOS Utilities
In this chapter you will learn about the Power On Self Test (POST) and how to
configure the system parameters using the System Configuration Utility (SCU).
The chapter includes:
– Power On Self Test (POST)
– System Configuration Utilities
– Features of the SCU
- Startup Menu
- Memory Menu
- Disks Menu
- Components Menu
BIOS Utilities
5
- Power Menu
- Exit Menu
– SCU Screen samples
5 - 1
User’s Guide
Power On Self Test (POST)
5
The system BIOS (Basic Input/Output System)
performs a series of tests on the system memory
and key computer components every time the
computer is powered on. These tests are called
the Power On Self Test (POST). Should an
error exist, the POST routine may halt execution (depending on the problem). If no error
exists, the POST will initialize the BIOS configuration, and boot (start) the operating system.
POST Message: Normal Operation
You will see the following screen if no error
exists after the POST is performed:
SystemSoft MobilePRO BIOS Version 1.01
(2482-00)-(R1.XX.prXX)
Copyright 1983-1996 SystemSoft Corp. All
Rights Reserved
500 MHz Celeron with MMX CPU
CPU Microcode Update Rev 007h Complete
L2 Cache: 128 KB Installed
8 MB Video RAM
SystemSoft Plug-n-Play BIOS ver 1.17.01
Base Memory 000640 KB
Extended Memory 056320 KB
Total Memory 057344 KB
Shared Memory 008192 KB
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration
Utility
5 - 2
INITIALIZING BOOT CD-ROM - CD-224E
INITIALIZING 2nd ATAPI - None
(Sample Screen)
POST Message: Error Detected
BIOS Utilities
If an error is detected, you will see the following
WARNING message. You may press the F1 key
to continue, or press the Ctrl-Alt-S keys simultaneously to enter the System Configuration Utility.
SystemSoft MobilePRO BIOS Version 1.01
(2482-00)-(R1.XX.prXX)
Copyright 1983-1996 SystemSoft Corp. All
Rights Reserved
500 MHz Celeron with MMX CPU
CPU Microcode Update Rev 007h Complete
L2 Cache: 128 KB Installed
8 MB Video RAM
SystemSoft Plug-n-Play BIOS ver 1.17.01
Base Memory 000640 KB
Extended Memory 056320 KB
Total Memory 057344 KB
Shared Memory 008192 KB
WARNING - FLOPPY DISK TRACK 0 FAILED
Auto Detecting IDE Devices[Done]
5
(Sample Screen)
<CTRL-ALT-S> to enter System Configuration
Utility
INITIALIZING BOOT CD-ROM - CD-224E
INITIALIZING 2nd ATAPI - None
<CTRL-ALT-S> to enter System Configuration
Utility
Press F1 to Continue
5 - 3
User’s Guide
System Configuration Utility
The System Configuration Utility (SCU) can be used to set your notebook’s
system parameters. The system date and time, power settings and other functions are set in the SCU. The settings are stored in a nonvolatile battery-backed
CMOS RAM. This simply means that your settings are saved even when the
notebook is turned off.
Information in the System Configuration Utility (SCU)
5
Here is a list of the system settings which may be changed within the SCU.
table 5-1
uneM smetIuneM
putratS
yromeM.yromeMderahSAGV
sksiD.sgnitteSEDI,sevirDetteksiD
stnenopmoC
rewoP
tixE
.ofnInoisreV
edoMVT,taepeRdraobyeK
yrettaBelbanE,yalpsiD,eciveDtooB,tooBtsaF,emiTdnaetaD
,peeBnOrewoPelbanE,edoMdnapxeDCLelbanE,peeBwoL
latigidFIDP/SelbanE,ogolMEOyalpsiD,troppuSSOPNPelbanE
.drowssaPUCS,drowssaPtooB,tuptuo
,kcolmuNdraobyeK,troPesuoM2/SP,troPTPL,stroPMOC
,gnivaSrewoPmuideM,gnivaSrewoPwoL,gnivaSrewoPelbanE
,remiTemuseR,slortnoCdnepsuS,ezimotsuC,gnivaSrewoPhgiH
.dnepsuSwoLyrettaBelbanE,emuseRgniRMEDOMelbanE
,sgnitteSerotseR,sgnitteStluafeD,)evaSoN(tixE,tixEdnaevaS
5 - 4
Initiating the System Configuration Utility
The System Configuration Utility (SCU) can be accessed by pressing the Ctrl,
Alt, and S keys simultaneously when you turn on your computer and see this
message:
<CTRL-ALT-S> to enter System Configuration Utility
This message lasts only a few seconds and if you don’t respond in time, the
computer will initiate the boot process. If you were unable to enter the SCU,
you must reboot the system and try again.
BIOS Utilities
!!
!
!!
Note
During startup,
if your computer has a logo
screen or picture appear
instead of the
POST screen,
wait until a
cursor appears
in the top right
corner before
hitting <CTRLALT-S> to
enter the SCU.
5
Notebook screen as it appears when you enter the SCU.
5 - 5
User’s Guide
Working with the Menu Bar
Use these keys to begin working in the SCU.
syeK noitcA
tlA.rabunemehtsthgilhgiH
(worratfeL !)
5
(worrathgiR ")
sretteldethgilhgiH
nottubesuomtfeL
(worranwoD #)
rabecapS
retnE
nottubesuomthgiR
csE
.noitporabunemastceleS
.noitporabunemehtsnepO
.noitcatnerrucslecnaC
table 5-2
5 - 6
Working with the Pull-down Menu
Once your desired menu bar item is highlighted, press Enter or the down arrow
(#) to see the pull-
BIOS Utilities
down menu items.
You move about the
pull-down menu
syeK noitcA
baT.rehtonaotdrocerenomorfsevoM
(sworrapU/nwoD # () $).dleifafoeulavehtsegnahC
with these keys:
rabecapS.dleifastceleS
:esoohcotuoyswollA
retnE
csE.neercstnerrucehtstiuQ
.segnahcynaevasot>KO<
.segnahcynaerongiot>lecnaC<
table 5-3
Some pull-down menu options have an arrow to the right of the entry.
Choose these options by pressing Enter and another screen will be displayed.
Navigate the new
screen with the
syeK noitcA
5
following keys:
table 5-4
(sworrapU/nwoD # () $)
.metiunemnwodllupastceleS
sretteldethgilhgiH
.noitcnufdeificepsehtselbasiD/selbanE
retnE
(A % .delbanesinoitcnufehtsetacidni)
sevasdnaunemnwodllupehtsesolC
csE
.segnahceht
5 - 7
User’s Guide
System Configuration Utility Options
5
Startup Menu
!!
!
!!
Note
Sample screens
of the various
SCU options
are shown on
pages 5-19 to 5-
21.
metI noitpO/gnitteS noitcnuF
dnaetaD
emiT
tooBtsaF
tooBts1
eciveD
eciveDtooB
tooBdn2
eciveD
raeY/htnoM/yaD
dnoceS/etuniM/ruoH
elbanE
elbasiD.tooBtsaFehtelbasiD
CksiDdraH
MOR-DC
evirD
AetteksiD
CksiDdraH
MOR-DC
evirD
.emitdnaetadehtteS
ehttoobylkciuqdnaezilaitinI
niatrecgnippiksybmetsys
.stsetcitsongaid
rofeciohcts1s’metsysehtyficepS
.evirdtoobeht
rofeciohcdn2s’metsysehtyficepS
.evirdtoobeht
5 - 8
table 5-5a
AetteksiD
CksiDdraH
tooBdr3
eciveD
MOR-DC
evirD
AetteksiD
.evirdtoobeht
rofeciohcdr3s’metsysehtyficepS
Startup Menu (continued)
metI noitpO/gnitteS noitcnuF
BIOS Utilities
DCL.lenapDCLs’metsysehtetavitcA
yalpsiD
elbanE
woLyrettaB
peeB
DCLelbanE
edoMdnapxE
elbanE
nOrewoP
peeB
TRC.rotinomlanretxenaetavitcA
TRC+DCL
elbanE
elbasiD.evobaehtelbasiD
elbanE
elbasiD.evobaehtelbasiD
elbanEpeeBnOrewoPelbanE
elbasiDpeeBnOrewoPelbasiD
ehtdnaDCLehthtobetavitcA
.TRC
lliwspeebgninrawfoseiresA
sirewopyrettabehtnehwdnuos
.wol
eritneehtllifotyalpsidehthctertS
.lenapDCLehtfoneercs
5
PNPelbanE
troppuSSO
elbanEtroppuSSOPNPelbanE
elbasiDtroppuSSOPNPelbasiD
table 5-5b
5 - 9
User’s Guide
Startup Menu (continued)
metI noitpO/gnitteS noitcnuF
5
&&
&
&&
Warning
If you choose to
set a boot pass-
word, NEVER
forget your
password, the
consequences
could be seri-
ous. If you
cannot remem-
ber your boot
password you
must contact
your vendor
and you may
lose all of the
information on
your HDD.
elbanE
MEOyalpsiD
ogol
elbasiD
elbanE
latigidFIDP/S
tuptuo
tooB
drowssaP
elbanE.tuptuolatigidFIDP/SelbanE
elbasiD.tuptuolatigidFIDP/SelbasiD
nO-rewoPdloretnE
drowssaP
nO-rewoPwenretnE
drowssaP
nO-rewoPwenyfireV
drowssaP
-rewoPotdrowssaPelbanE
nO
.metsys
ehtyalpsidoterutaefehtelbanE
.toobmetsysgnirudogolMEO
ehtyalpsidoterutaefehtelbasiD
.toobmetsysgnirudogolMEO
ehtgnitoobrofdrowssapateS
aretneohwsresuylnO.retupmoc
ehttoobnacdrowssaptcerroc
5 - 10
table 5-5c
drowssaPpU-teSdloretnE
ehtgniyfidomrofdrowssapateS
UCS
drowssaP
drowssaPpU-teSwenretnE
drowssaPpU-teSwenyfireV
pU-teSotdrowssaPelbanE
.UCS
ehtretneohwsresuylnO.UCS
ehtegnahcnacdrowssaptcerroc
Memory Menu
metI snoitpO/sgnitteS noitcnuF
BIOS Utilities
BM8
derahSAGV
yromeM
Important: The value for VGA shared memory must be less than the
amount of RAM in your computer!
In the SCU utility you are able to set the value for the VGA Shared Memory.
The default is 8MB. If you choose to set the VGA Shared Memory to the maxi-
mum of 64MB YOU MUST have more than 64MB of RAM in your computer. If
the VGA Shared Memory equals the amount of RAM you will be unable to boot
your computer. The only way to correct this error and be able to boot your
computer again would be to add more RAM.
BM61
ezisyromemderahsAGVehttceleS
BM23
BM46
table 5-6
5
5 - 11
User’s Guide
Disks Menu
metI noitpO/gnitteS noitcnuF
5
sevirDetteksiDAevirD
sgnitteSEDI
enoN
BM44.1
delbanEevirD
DDHyramirP
edoM
-DVD/MOR-DC
MOR
AMDUEDI
001/66/33
noitcnuF
rotceSelpitluM
edoMOIP
delbanEevirD
edoMOIP
elbanE
elbasiD
.sgnittes
rofepytevirdehtyficepS
.Aevirdetteksideht
EDIdecnahneelbanE
EDIelbasiDroelbanE
001/66/33-AMDartlU
.noitcnuf)001/66/33-ATA(
5 - 12
elbanE
O/ItiB23EDI
elbasiD
table 5-7
tib-23elbasiDroelbanE
neewtebsnoitacinummoc
.rellortnocEDIdnaUPC
Components Menu
metI noitpO/gnitteS noitcnuF
BIOS Utilities
enoN
O/IBMOC
sgnittes
4QRI,8F3,1MOC
3QRI,8F2,2MOC
01QRI,8E3,3MOC
11QRI,8E2,4MOC
&3MOC(.noitarugifnocBMOCehtyficepS
.)SOPnP-nondnaedomSODrofylno4MOC
5
)05561(lamroN
stroPMOC
gnittesedoM
BMOCrof
gnittesAMD
RITSAFrof
)RISPH(ADrI
RIKSA
RITSAF
0AMD
1AMD
3AMD
.erawdrahBMOCehtenifeD
.noitarugifnocAMDRItsaFehtyficepS
table 5-8a
5 - 13
User’s Guide
Components Menu (cont’d)
5
metI noitpO/gnitteS noitcnuF
enoN
,873rddA,1TPL
troP
sserddA
7QRI
,872rddA,2TPL
5QRI
,CB3rddA,3TPL
7QRI
.noitarugifnoctropTPLehtyficepS
)scinortneC(TAdradnatS
5 - 14
table 5-8b
troPTPL
2/SP
troPesuoM
troP
noitinifeD
gnittesAMD
PCErof
edom
epyTPPE
elbanE
elbasiD
1AMD
3AMD
7.1PPE
9.1PPE
.esuom2/SP
)2/SP(lanoitcerid-iB
)PPE(lellaraPdecnahcnE
)PCE(seitilibapaCdednetxE
.noitarugifnocAMDPCEehtyficepS
.epytPPEehtyficepS
lanretxenarodapkcarts'metsysehtelbanE
nafiesuom2/SProdapkcartehtelbasiD
.tropAMOCotdetcennocsiesuomlanretxe
Components Menu (cont’d)
metI noitpO/gnitteS noitcnuF
BIOS Utilities
draobyeK
kcolmuN
taepeRyeK
etaR
draobyeK
taepeR
yaleDyeK
elbanE
.emittoobmetsys
elbasiD
spc2
spc6
spc01
.desserpelihwstaeperyek
spc51
spc02
spc03
ces4/1
ces2/1
ces4/3
tafforonosikcoLmuNrehtehwyficepS
ahcihwta)dnocesrepsretcarahc(etarehT
ssaplliwtaht)sdnoces(emitfotnuomaehT
.taeperotstratsyekdesserparetfa
5
ces1
edoMVT
sedoMVT
noitceleS
CSTN
.troptuo-VTehthtiwesu
LAP
otdnetniuoydradnatsnoisiveletehttceleS
table 5-8c
5 - 15
User’s Guide
Power Menu
metI noitpO/gnitteS noitcnuF
elbanE
gnivaSrewoPelbanE
elbasiD
.serutaefgnivasrewopllaelbasiD/elbanE
5
elbanE
gnivaSrewoPwoL
elbasiD
rewoPmuideM
gnivaS
gnivaSrewoPhgiH
ezimotsuC
ksiD
ybdnatS
elbanE
elbasiD
elbanE
elbasiD
ceS5
ceS01
ceS02
ceS03
niM1
.efilyrettab
.dessecca
.efilyrettabtsetrohseht
.efilyrettabtsegnoleht
dnaecnamrofrepmumixamnistlusergnittessihT
dnaecnamrofrepetaredomnistlusergnittessihT
dnaecnamrofrepmuminimnistlusergnittessihT
tonsitifiedomybdnatsretnelliwksiddrahehT
ksiddraH.doirepdeificepsehtnihtiwdessecca
sievirdksidehtnehwderotsereblliwrewop
5 - 16
niM5
niM01
nOsyawlA
table 5-9a
Power menu (cont’d)
metI noitpO/gnitteS noitcnuF
slortnoCdnepsuS
BIOS Utilities
*
rewoP
ffO/nO
rewoP
nottuB
*noitcnuF
dnepsuS
epyT
/dnepsuS
emuseR
otdnepsuS
ksiD
derewoP
no
dnepsuS
.fforono
.UCSehtni
.tnemeganam
metsysehtnrutotdesusinottubrewopehT
The power
nahteromrofnottubrewopehtsserpuoyfI
ehtretnelliwretupmocehtsdnocesruof
rewopehtsserpuoyfI.etats**ffolacinahcem
retupmocehtsdnocesruofnahtsselrofnottub
deificepsevahuoyepytdnepsusehtretnelliw
button acts as a
suspend/re-
sume button for
switching the
system between
a working state
and the sus-
rewoprofedomdnepsusehtyficepS
pend mode.
5
mralA
emuseR
remiTemuseR
emuseR
elbanE
elbasiD.evobaehtelbasiD
etuniM/ruoH/yaD/htnoM
.)etunimdnaruoh,yad,htnom(
dnepsusderugifnocehtmorfsemusermetsyS
.seripxeremitmralaemuserehtnehwedom
**
emitdeificepsehttaemuserlliwmetsysehT
In the mechani-
cal-off state the
system can only
edomSOProRTSmorfmetsysehtemuseR
gniRMEDOMelbanE
emuseR
elbanE
.)trop
hcihw(detcetedsignirmedomanehw
lairesehtotdetcennocebdluohsmedom
resume from
suspend mode
by pressing the
power button.
elbasiD.evobaehtelbasiD
ksidotmetsysehtdnepsusyllacitamotuA
woLyrettaBelbanE
dnepsuS
elbanE
elbasiD.evobaehtelbasiD
.noitidnocyrettabwolanopu
table 5-9b
5 - 17
User’s Guide
Exit Menu
metI noitcnuF
tixEdnaevaS.metsysehttooberdnasgnittestnerrucehtevaS
)evaSoN(tixE.segnahcynagnivastuohtiwtixE
5
tluafeD
.)MORnidnuofsenolanigiroeht(sgnittestluafedehterotseR
sgnitteS
erotseR
.senosuoiverpehtotputestnerrucehterotseR
sgnitteS
ofnInoisreV.noitamrofninoisrevSOIBtnerrucehtwohS
table 5-10
5 - 18
SCU Screen samples
Startup Screen
BIOS Utilities
5
Memory Screen
5 - 19
User’s Guide
5
Disks Screen
Components Screen
5 - 20
Power Screen
Exit Screen
BIOS Utilities
5
5 - 21
Notes:
Chapter 6. Driver Installation
This chapter deals with installing drivers and utilities essential to the operation
or improvement of some of the notebook’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most
available operating systems haven’t built in drivers and utilities. Thus, some of
the system components won’t be auto-configured with an appropriate driver or
utility during operating system installation. Instead, you need to manually
install some system-required drivers and utilities. The information here has
been designed for users with basic computer knowledge though inexperienced
users may also find this section helpful. This chapter includes:
– Before installing Windows
Driver Installation
6
– Installing Windows 98 SE (For reference only)
– Installing Windows Me (For reference only)
– Installing Windows 2000 (For reference only)
– Installing Drivers in Windows 98 SE
– Installing Drivers in Windows Me
– Installing Drivers in Windows 2000
– Installing Drivers in Windows NT4.0
In this chapter, we assume that you will install all drivers and utilities from the
CD device and it is assigned to Drive D:.
6 - 1
User’s Manual
Before Installing Windows
6
55
5
55
Note
Before installing Windows
98SE or Windows Me you
will need to
partition and
format your
HDD (hard disk
drive).
Partitioning the HDD
1. Insert the Windows Boot Disk in the FDD before you turn on the system.
2. Choose the “Start computer with CD-ROM support” option.
3. When the “A:\” prompt appears, type fdisk [Enter] and
a. Type Y for large disk support.
b. Choose 1 to “Create DOS partition...”.
c. Choose 1 (again) to “Create a Primary DOS partition”.
d. Confirm (Y) for “...maximum size...” and “...active...”.
e. When fdisk is finished, press Esc, shut-down and restart.
4. Turn off your computer.
Formatting the HDD
5. Restart your computer with the Boot Disk still in the FDD
6 - 2
6. When the “A:\” prompt appears, type format c: /s and proceed (Y).
(When asked, you don’t have to give it a label.)
Now your HDD is partitioned and formatted and an operating system can
be installed on it.
7. Go to the following pages depending on the system you are installing:
Windows 98 - page 6-3
Windows Me - page 6-4
Installing Windows 98 SE (for reference only)
1. Insert the Windows Boot Disk in the FDD and turn on your computer.
2. Choose option 1 “Start computer with CD-ROM support.”
3. Place the Windows 98 CD into the CD-ROM drive.
4. Type D:setup. (this will start the setup process for Windows 98 CD)
5. Press Enter (your drives will be scanned for errors.)
6. Select Exit (the Windows 98 setup will now begin)
7. When the “Windows 98 Setup” program initializes, click Continue.
8. The “License Agreement” dialog box appears. Select “I accept the Agreement” and click Next.
9. For “Windows Product key”, enter the product’s ID number and press
Driver Installation
55
5
55
Note
If your Windows CD-ROM
is bootable, you
can change the
SCU to boot
from the CDROM and
install the OS
accordingly.
00
0
00
6
Next.
10.The “Select Directory” dialog box appears. Select the path of
“C:\Windows”, or type another path if you prefer. Then click Next.
11.When you see “Setup Options”, select “Portable” and click Next.
12.Follow the on-screen instructions and choose the recommended options.
13. Restart your computer.
Windows is now installed on your computer.
Windows Setup Notes:
- During the setup process, the system will restart several times. When it
shuts down for the first time, remove the Boot Disk.
- Allow Windows to install its default drivers.
Warning
If you intend to
use the Sus-
pend to Disk
power management function
available with
your computer
you must also
create an additional partition
prior to installing Windows 98
or 98SE. (See
page 3-5.)
6 - 3
User’s Manual
6
Installing Windows Me (for reference only)
1. Insert the Windows Boot Disk in the FDD and turn on your computer.
2. Choose option 1 “Start computer with CD-ROM support.”
3. Place the Windows Me CD into the CD-ROM drive.
4. Type D:setup. (this will start the setup process for Windows Me CD)
5. Press Enter (your drives will be scanned for errors.)
6. Select Exit (the Windows Me setup will now begin)
7. When the “Windows Me Setup” program initializes, click Continue.
8. The “License Agreement” dialog box appears. Select “I accept the Agreement” and click Next.
9. For “Windows Product key”, enter the product’s ID number and press
Next.
6 - 4
10.The “Select Directory” dialog box appears. Select the path of
“C:\Windows”, or type another path if you prefer. Then click Next.
11.When you see “Setup Options”, select “Portable” and click Next.
12.Follow the on-screen instructions and choose the recommended options.
13. Restart your computer.
Windows is now installed on your computer.
Windows Setup Notes:
- During the setup process, the system will restart several times. When it
shuts down for the first time, remove the Boot Disk.
- Allow Windows to install its default drivers.
Installing Windows 2000 (for reference only)
1. Insert the Windows 2000 Installation CD disk and start your computer.
Driver Installation
55
5
55
2. Press any key to start the installation immediately after the message
“Press any key to boot from CD.” appears.
3. When “Windows 2000 Setup” appears, press Enter to continue.
4. “Windows 2000 Professional Setup” starts copying files to your HDD.
5. After copying, press Enter to restart your computer.
6. After entering “Windows 2000 Professional Setup”, press Enter to “set up
Windows 2000 now”.
7. Press F8 for “Windows 2000 Licensing Agreement”.
8. Select the partition (drive) where you want to install Windows 2000, and
press Enter.
9. Choose the file system you want and press Enter. (Usually choose the
“FAT” file system.)
10.To format the drive (partition), press F. (Please note all data on the formatted drive will be lost.)
11.Setup will proceed with formatting, file-copying, and will reboot the system.
12.When the system enters Windows 2000, follow the on-screen instructions
and press Next.
13.When Windows asks for Your Product Key, type the product’s ID number
and then press Next.
Note
To insert the
disk:
1) open the CD
drive using the
emergency eject
hole page2-14
or
2) turn on the
computer, open
the drive, insert
the CD, then
restart the
computer.
55
5
55
Note
The installation
steps may be
different depending on
your system’s
status. For
details, refer to
your Windows
2000 manual.
6
6 - 5
Loading...