GE P&W PRO LA Series 50 Hz User Manual
Find a contact near you by visiting www.ge.com/water and clicking on “Contact Us”.
* Trademark of General Electric Company; may be registered in one or more countries.
©2013, General Electric Company. All rights reserved.
AM-FSpwPRO_LA_Series_50Hz_Br_EN.doc May-13
Fact Sheet
PRO LA Series 50 Hz
Reverse Osmosis Machines from 10 to 100 m3/h
Instrumentation
Flow Meters Permeate & Concentrate
Conductivity Permeate
Pressure Pre & Post Cartridge Filter
RO Feed , Pump Outlet, Interstage (x2)
Concentrate & Permeate
Pressure Switch Feed, Permeate, Concentrate
PH (optional) Feed
ORP (optional) Feed
Instrument Center GF Signet
Specific Basic Features (BAS)
AB PanelView 300
3.0-inch Monochrome Display
Touch Screen Controls
AB Micrologix PLC
Communication: RS232
4-20 mA Instruments Displayed on Instrument
Center
NR-10 Electrical Panel
Specific Premium Features (PRE)
AB PanelView Plus 700
7.0-inch Color Display
Text and Pictorial Operating Screens
Touch Screen Controls
AB CompactLogix PLC
Communication: Ethernet
4-20 mA Instruments on Touch Screen
Primary and final Pressure Transmitters
Conductivity Transmitter on Feed
RO permeate Flush on Shutdown
NR-10 Electrical Panel
NR-13 compliance
PH meter on RO Feed
Options Available
GE Fanuc PLC Control Package
Membrane Options:
400 Square Foot Elements
High Rejection Elements
Low Energy Elements
Motor Starter
Variable Frequency Drive
ORP meter
pH meter (basic)
PRO LA Accessories
PRO Multi-Media filters
PRO Activated Carbon and Softeners
PRO Clean-in-Place units
PRO Chemical Feed Systems
Transfer Pumps and Storage Tanks
Operating Parameters
Design Recovery1 75%
Design Temperature 20ºC
Operating Temperature Range 2-30 ºC
Nominal rejection 97-99%
System Inlet Pressure 2–4 bar
1
Recovery Rate can vary +/- 5%
MODEL
PRO-11-LA
PRO-23-LA
PRO-34-LA
PRO-45-LA
PRO-68-LA
PRO-102-LA
Permeate Rate
2
:
Concentrate Rate:
Concentrate Recycle:
Feed Rate:
11 m3/hr
4 m3/hr
2.3 m3/hr
15 m3/hr
23 m3/hr
7.5 m3/hr
2.3 m3/hr
30.5 m3/hr
34 m3/hr
11 m3/hr
NA
45 m3/hr
45 m3/hr
15 m3/hr
3.4 m3/hr
60 m3/hr
70 m3/hr
23 m3/hr
NA
93 m3/hr
100 m3/hr
34 m3/hr
NA
134 m3/hr
Pumps and Motors
Model:
Manufacturer:
Quantity:
Motor Power and type:
Installed Power:
Design Flow Rate:
Design boost pressure:
SS8520
Osmonics/Tonkaflo
1
14.9kW (20HP) TEFC
14.9 kW
17 m3/hr (75 gpm)
15.9 Bar (230 psig)
SS24011
Osmonics/Tonkaflo
1
37.3 kW (50 Hp) TEFC
37.3 kW
34 m3/hr (150 gpm)
15.9 Bar (230 psig)
SS24013
GE/Tonkaflo
1
37.3 KW (50 Hp) TEFC
37.3 KW
45.4 m3/hr (200 gpm)
15.9 Bar (230 psig)
AS40410
GE/Tonkaflo
1
37.3 KW (50 Hp) TEFC
37.3 KW
68.1 m3/hr (300 gpm)
13.8 Bar (200 psig)
SS24013
GE/Tonkaflo
2
37.3 KW (50 Hp) TEFC
37.3 KW
90 m3/hr (400 gpm)
15.9 Bar (230 psig)
AS40410
GE/Tonkaflo
2
37.3 KW (50 Hp) TEFC
37.3 KW
136 m3/hr (600 gpm)
13.8 Bar (200 psig)
Membrane Elements and Housings
Membranes Quantity:
Memb. Housing Style:
Banking Arrangement:
12
4 element long,
4 port
111
24
4 element long,
4 port
321
36
6 element long,
4 port
321
48
4 element long,
4 port
642
72
6 element long,
4 port
642
108
6 element long,
4 port
963
Cartridge Filtration
Housing Model:
Housing Quantity:
Cartridge Filter Model:
Cartridge Filter Length:
Cartridge Filter Qty:
HX-0740-3.0-V-316
1
RO.Zs01-40XK
102 cm (40”)
7 per housing,
7/change out
HX-0740-3.0-V-316
1
RO.Zs01-40XK
102 cm (40”)
7 per housing,
7/change out
HX-0740-3.0-V-316
2
RO.Zs01-40XK
102 cm (40”)
7 per housing,
14/change out
HX-0740-3.0-V-316
2
RO.Zs01-40XK
102 cm (40”)
7 per housing,
14/change out
HX-0740-3.0-V-316
3
RO.Zs01-40XK
102 cm (40”)
7 per housing,
21/change out
HX-0740-3.0-V-316
4
RO.Zs01-40XK
102 cm (40”)
7 per housing,
28/change out
Installation and Utility Requirements
Inlet:
Permeate:
Concentrate:
Inlet Water Pressure:
Air Pressure:
Drain to be Sized for:
Power:
Control Circuit
2.0” flange
1.5” flange
1.0” flange
2 bar, minimum
7 bar, oil-free
15 m3/hr (67 gpm)
380-400 VAC, 3-phase,
50Hz
220 VAC, 1-phase, 50Hz
3.0” flange
3.0” flange
1.5” flange
2 bar, minimum
7 bar, oil-free
30 m3/hr (133 gpm)
380-400 VAC, 3-phase,
50Hz
220 VAC, 1-phase, 50Hz
3.0” flange
3.0” flange
1.5” flange
2 bar, minimum
7 bar, oil-free
45.4 m3/hr (200 gpm)
380-400 VAC, 3-phase,
50Hz
220 VAC, 1-phase, 50Hz
4.0” flange
3.0” flange
2.0” flange
2 bar, minimum
7 bar, oil-free
60.6 m3/hr (267 gpm)
380-400 VAC, 3-phase,
50Hz
220 VAC, 1-phase, 50Hz
4.0” flange
4.0” flange
2.0” flange
2 bar, minimum
7 bar, oil-free
91 m3/hr (400 gpm)
380-400 VAC, 3-phase,
50Hz
220 VAC, 1-phase, 50Hz
6.0” flange
6.0” flange
3.0” flange
2 bar, minimum
7 bar, oil-free
136 m3/hr (600 gpm)
380-400 VAC, 3-phase,
50Hz
220 VAC, 1-phase, 50Hz
Skid
Height:
Width:
Depth:
Shipping Weight
Estimate:
193 cm (76”)
117 cm (46”)
493 cm (194”)
1542 kg (3400 lb)
193 cm (76”)
117 cm (46”)
493 cm (194”)
2040 kg (4500 lb)
193 cm (76”)
117 cm (46”)
696 cm (274”)
2720 kg (6000 lb )
193 cm (76”)
203 cm (80”)
493 cm (194”)
3175 kg (7000 lb)
193 cm (76”)
203 cm (80”)
696 cm (274”)
4305 kg (9500 lb)
193 cm (76”)
203 cm (80”)
696 cm (274”)
6350 kg (14,000 lb)
Materials of Construction
High-pressure piping 316 Stainless Steel, Sch. 10
Low-pressure piping PVC, Sch. 80
Frame Painted blue carbon steel
Enclosure Nema 12
Clamps/fittings Zinc-plated
Membrane Elements and Housings
Membrane Model AG8040F
Style Spiral-wound elements
Manufacturer GE
Membrane type TFC (Polyamide)
GE PRO Models
Membrane Elements and Housings continued
Average membrane flux 16-17 gfd
Membrane rejection 99.0-99.5 %
Manufacturer GE
Housing material 316 Stainless Steel or FRP
Housing Pressure Rating 31 Bar
1
Flux can be reduced by using 400-sqft membranes.
Cartridge Filtration
Housing model GE HX-0740-80-V316
Housing material 316 Stainless Steel
Cartridge filter 1-micron nominal, ROsave.Z*s
1
2
Maximum permeate rate listed at design temperature. Permeate rate can be reduced by up to 15%.
Fact Sheet Page 2
Loading...