GE P&W GE Series User Manual
Fact Sheet
Find a contact near you by visiting www.gewater.com and clicking on “Contact Us”.
* Trademark of General Electric Company; may be registered in one or more countries.
©2013, General Electric Company. All rights reserved.
AM-FSpwGESeries_EN.doc Nov-13
Membrane
G-Series, Thin-Film Membrane (TFM*)
Model
Average permeate flow
gpd (m3/day)
1
MWCO (Dalton)
GE2540F30
740 (2.8)
1,000
GE2540F50
500 (1.9)
1,000
GE4040C50
2,000 (7.6)
1,000
GE4040F30
2,600 (9.8)
1,000
GE8040F30
10,000 (37.8)
1,000
GE8040F50
7,300 (27.6)
1,000
Model
Spacer
mil (mm)
Active area
ft2 (m2)
Outer wrap
Part
number
GE2540F30
30 (0.76)
27 (2.5)
Fiberglass
1207086
GE2540F50
50 (1.27)
18 (1.7)
Fiberglass
1207087
GE4040C50
50 (1.27)
70 (6.5)
Cage
1207091
GE4040F30
30 (0.76)
91 (8.5)
Fiberglass
3050063
GE8040F30
30 (0.76)
358 (33.2)
Fiberglass
1207098
GE8040F50
50 (1.27)
260 (24.2)
Fiberglass
1207096
Model1
Dimensions, inches (cm)
Boxed
A
B2
C3
Weight
lbs (kg)
GE2540F30
40.0
(101.6)
0.75
1.90 (OD)
2.4
(6.1) 4 (1.8)
GE2540F50
40.0
(101.6)
0.75
1.90 (OD)
2.4
(6.1) 4 (1.8)
GE4040C50
40.0
(101.6)
0.625
(1.59)
3.9
(9.9) 9 (4.1)
GE4040F30
40.0
(101.6)
0.75
(1.90) OD
3.9
(9.9) 9 (4.1)
GE8040F30
40.0
(101.6)
1.125
(2.86)
7.9
(20.1)
29
(13.2)
GE8040F50
40.0
(101.6)
1.125
(2.86)
7.9
(20.1)
29
(13.2)
Typical Operating Flux
5-20 GFD (8-34 LMH)
Maximum Operating Pressure
400psi (2,760kPa)
Maximum Temperature
Continuous Operation: 122°F (50°C)
Clean-In-Place (CIP): 122°F (50°C)
pH Range
Continuous Operation: 2.0-10.0
Clean-In-Place (CIP): 1.0-11.5
Maximum Pressure Drop
Over an element: 15psi (103kPa)
Per housing: 60psi (414kPa)
Chlorine Tolerance
20-50ppm days
GE Series
Industrial Ultrafiltration Elements – TFM* 1,000 MWCO
The G-Series GE family of proprietary thin-film ultrafiltration membrane elements is characterized by a
molecular weight cutoff of 1,000 on polyethylene
glycol and a smooth, fouling resistant membrane
surface.
GE Elements are used for surface water pretreatment, color/TOC reduction, and chemical purification.
Table 1: Element Specification
1
Flux specifications are based on fouling free water at 410psi operating pressure
(2,827kPa), 77°F (25°C), and 10% recovery.
Individual element flux may vary ± 25%.
Figure 2: Element Dimensions Diagram – Male
Table 2: Dimensions and Weight
1
These elements are dried and bagged before shipping.
2
Internal diameter unless specified OD (outside diameter).
3
The element diameter (dimension C) is designed for optimum performance in GE
pressure vessels. Other pressure vessel dimension and tolerance may result in
excessive bypass and loss of capacity.
Table 3: Operating and CIP parameters
Figure 1: Element Dimensions Diagram – Female
Loading...