GE Profile PFQ97HSPVDS Accessory Guide

Accessories Guide

& Installation Instructions

GE Profile™

UltraFast
Combo

Pub. No. 14-D0026-23

Pub. No. 14-D0026-23

THANK YOU FOR MAKING GE PROFILE A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first,

we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every
GE Profile product, and we think you will too. Among other things, registration

of your appliance ensures that we can deliver important product information

and warranty details when you need them.

These parts and accessories, which are not exclusive for use with the

GE Profile UltraFast Combo, can be ordered on-line through

GEApplianceparts.com today, 24 hours a day or by phone at

877.959.8688 during normal business hours.

This Accessories Guide is not intended to be a replacement for the instructions

that may accompany these items. Please review those instructions before

proceeding with any installations.

TABLE OF
CONTENTS

STANDARD ITEMS

o RISER IN CARBON GRAPHITE - GFR0728PTDS 2
o 6’ STEEL WASHER HOSES 90° ELBOWS; 2-pack - WX14X10011 4
o HOSE FILTER SCREEN (1) - WH1X2267 4

o 4’ RUBBER HOSES - PM14X10002 5

o FILTER FOAM PAD - WH01X35719 5
o 4" DUCT VENT CAP - WX08X10070 6
o APPLIANCE BRUSH SET - PM14X10056 6
o SMART HQ APP - geappliances.com/connect 7

SPECIAL INSTALLATION NEEDS

o UNICOUPLE WASHER HOSE ASM - WH41X36697 8

o DRAIN HOSE EXTENSION KIT - WH49X316 10

o UNIVERSAL FLOOR PAN/DRAIN - PM7X2 11
o TOUCH-UP PAINT CARBON GRAPHITE - WR97X27706 11

TWO COMBO INSTALLATION

o 1’ HOSE SPLITTER - 2 WAY (2 NEEDED) - WX14X10014 12
o 4-PRONG 240V TO 110V PLUG ADAPTER - GFAPC120V or equivalent 13

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 1

RISER GFR0728PTDS

7" RightHeight™ Riser / Carbon Graphite

x 22

1. INSTALL REAR RISER BRACKETS

▪ Align rear riser bracket as shown on both

sides.

2. INSTALL FRONT RISER BRACKETS

▪ Install front brackets on both sides.

RISER BRACKETS

COMBO BRACKETS

3. INSTALL COMBO BRACKETS

▪ Lay the Combo on its back on a protective

surface. Ensure leveling legs are threaded

to the minimum height.

▪ Install front brackets on the bottom of the

Combo as shown. Use the 2 holes closest
to the front and the 2 outermost holes on
the bracket. The bracket should not go
beyond the edge of the appliance.

▪ Install the rear brackets on the bottom of

the Combo. Use the top 2 holes on the
bottom of the Combo with the tab on the
bracket facing the outside.

2 | GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com

TOOLS YOU WILL NEED

o Safety Glasses

o 9/16” open-end wrench

o ¼” Socket & Nut Driver

o Level

o Gloves

RISER (continued)

4. JOIN REAR BRACKETS

▪ Lift riser and hook front brackets of the

riser to front brackets of the Combo.

▪ Align front and rear brackets on Combo

with front and rear brackets on the riser
and loosely fasten the screws. Make sure
the bracket from the Combo is to the
INSIDE of the riser bracket and not the
outside.

5. LEVEL THE COMBO

▪ Locate the 4 legs from the parts package

and install TO MINIMUM HEIGHT.

▪ Stand the Combo upright.
▪ Securely tighten all screws in all brackets.
▪ Make sure the Combo is level by placing a

spirit level on top. Check side to side and
front to back.

▪ Use a 9/16” open

ended wrench to
adjust the legs in

and out. Tighten

the lock nut
against the bottom
of the riser.

NOTE: To minimize vibration the locking
nuts must be tight.

6. ADJUST COMBO LEGS

▪ Snug the feet of the Combo to the top of

the riser to minimize vibration.

7. REMOVE SHIPPING BOLTS & BRACE

▪ Remove the 4 shipping bolts on the back

side of the Combo and the top brace.

8. FINALIZE THE INSTALLATION

▪ Refer to the Combo installation

instructions to complete the installation.

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 3

WASHER HOSES - 90° WX14X10011

6’ STAINLESS STEEL HOSES 90° ELBOWS; 2-pack

WASHER HOSES FILTERS WH1X2267

FILTER INSERT FOR HOSES (1)

1. Insert in the end of the hose that is connected
directly to the faucet

2. The filter screen should be inserted so that the
parabolic shape is inside the hose and pointed

away from the faucet.

3. Use a standard hose rubber washer in the end of
the hose that is connected to hot or cold valves of
the Combo.

1. Insert the rubber washers (if not already

installed) into the ends of the hoses.

2. Attach the 90 degree elbow end of each of the
hoses to the faucets – one to the HOT and the
other to the COLD.

3. Attach the other (straight) end of the hoses to
the HOT valve and the other to the COLD valve
making sure that the lines are properly matched.

4. Tighten, but do not overtighten, the hose fittings
using a pair of pliers.

5. Turn on the faucets and check for leaks.

x 2

4 | GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com

WASHER HOSES PM14X10002

4’ RUBBER WASHER HOSES (2 PACK)

FILTER FOAM PAD WH01X35719

SPONGE PAD FOR COMBO FOAM FILTER

1. Remove the dual-stage lint filter from the Combo.

2. Open the filter frame and remove the old foam

filter pad and discard.

3. Insert the new foam pad into the filter frame,
ensuring proper alignment using the locating tabs.

4. Snap the frame back into place and return the
dual stage lint filter back to the Combo.

1. Insert the rubber washers (if not already

installed) into the ends of the hoses.

2. Attach one end of each of the hoses to the
faucets – one to the HOT and the other to the
COLD.

3. Attach the other end of the hoses to the HOT
valve and the other to the COLD valve making
sure that the lines are properly matched.

4. Tighten, but do not overtighten, the hose fittings
using a pair of pliers.

5. Turn on the faucets and check for leaks.

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 5

DUCT VENT CAP WX08X10070

4" DUCT VENT CAP

APPLIANCE BRUSH SET PM14X10056

FOR CLEANING INSIDE THE FILTER AREA

• Maintain efficiency with a set of brushes that
make cleaning hard-to-reach areas easy

• Designed for the Combo and conventional dryer
venting and more.

Watch this video to see how

these brushes are used in
the cleaning of the Combo
filter area.

• Durable bump & heat resistant PVC construction

• Used to terminate a round 4” duct previously used

by a vented dryer.

• Readily fits a 4” duct pipe and can be fastened with

a flat head screwdriver with the included hose
clamp.

1. Clean any debris that is in the duct line and discard
the old ducting from your previous dryer, if
applicable.

2. Install the PVC cap onto the open duct protruding
from the wall.

3. Using a flathead screwdriver, tighten the hose
clamp to secure it to the duct.

6 | GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com

SmartHQ APP geappliances.com/connect

UNLOCK FEATURES, UPDATES & NOTIFICATIONS

1. Download the app and sign in or create a new
account. (Note: When you create an account, fill in

the required information and register. You’ll get an

email asking you to verify your account. After
verifying, sign-in to the app.)

2. After signing in, you’ll go to the welcome screen.
From here, select your brand of appliance, the

appliance category and the type of appliance

you’re connecting.

3. The instructions for proceeding are different

depending on the appliance you’re connecting.

Follow the links below for each individual
appliance you want to connect.

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 7

Download the SmartHQ App

To get started, download the free SmartHQ™ App

for your Apple or Android phone.

SmartHQ is your key to connection.

Use the app to connect, control and manage your

GE Profile UltraFast Combo.

UNICOUPLER WH41X36697

UNICOUPLE WASHER HOSE ASM

8 | GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com

The Unicoupler must be assembled
before it is connected to the Combo.

1. ASSEMBLE THE UNICOUPLER

▪ Loosen & insert a clamp over the end of the

blue drain hose from the Combo and press
the hose with clamp onto the Unicoupler’s
drain connector.

▪ Turn the clamp key clockwise and tighten the

hose to secure it to the UniCoupler.

TOOLS YOU WILL NEED

o Safety Glasses o Pliers

o Levelo Gloves

o Phillips-Head

Screwdriver

NOTE: Some parts shown may come
preassembled.

2. CONNECT TO WATER LINE

▪ Remove the aerator from the sink faucet and

screw on the faucet adapter, using pliers to
unscrew it is too tight to unscrew by hand.

▪ Attach the hose connector to the faucet

adapter by pulling down on the locking collar
while lifting up on the connector until it snaps
into place. Ensure the water filter is in place.

8. CONFIRM OPERATION WITH COMBO

▪ Try running a quick RINSE & SPIN to

confirm that water is being supplied to
the Combo at the temperature you
selected at the faucet.

9. SET THE WASHER CONTROLS

▪ Select your desired cycle and options.

Regardless of whether you select
Tap Cold, Cold or Warm, the Combo
will use the water at the temperature
supplied by the faucet.

▪ For cycles requiring

Hot or Ex. Hot
water like the
Sanitize cycle, the
Combo will alert
you that you must
adjust the water
temp at the sink.

UNICOUPLER (continued)

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 9

4. CONNECT TO COLD VALVE INLET

Note: Unplug electrical cord before
installing water hose.

▪ If not installed, install rubber washer in

one end of cold water.

▪ Thread COLD

water hose onto
the BLUE
connection

(right side).

NOTE: Only the
cold valve will be
connected for this
installation.
Hot valve should NOT be connected.

▪ Hand tighten and use pliers to tighten

hoses between 1/8 and 1/4 turn beyond
hand tight.

5. INSTALL CAP ON HOT VALVE

▪ Install and

tighten
cap on hot
water valve
inlet to
prevent
water from
leaking
from this

connection.

7. SLOWLY TURN ON THE WATER AT THE
FAUCET ALL THE WAY TO THE DESIRED
WASH TEMPERATURE

ERROR

Confirm H2O Supply is

ON

Fault Code: 8

Dismiss

DRAIN HOSE EXTENSION WH49X316

DRAIN HOSE EXTENSION KIT FOR COMBO

• Flex tubing adapter to extend drain hose from Combo to
standpipe. Use to extend the drain hose for discharge

heights between 60” and 90”.

• Parts in Kit: Extension Hose, screw clamp, hose adapter,
sleeve, instruction sheet

• Dimensions: 66" long by 1” diameter.

1. Unplug and move washer to gain access to drain hose.

2. With the washer moved out and hose still attached to
the washer, insert

the sleeve at the

rubber end of the
drain hose.

3. Insert the hose adapter into one end of the extension
hose and slide
the hose clamp
onto the
extension hose.

4. Insert existing drain hose with sleeve inserted into it
inside the drain hose extension adapter that has been
inserted into the drain hose extension.

NOTE: Liquid soap may be applied to the existing
drain hose for ease of insertion.

5. Slide the clamp into
the position as shown.

6. Tighten the hose clamp so that it secures the sleeve
and the hose adapter in place.

7. Reinstall drain hose into stand pipe. Drain hose should
be no more than 5 inches into the stand pipe. Test to
ensure there are no leaks.

NOTE: DO NOT use more than 1 extension drain hose kit.

Position Clamp

Between Lines

10 | GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com

FLOOR PAN PM7X2

LOW PROFILE FLOOR PAN WITH DRAIN / WHITE

• Low profile tray perfectly fits the Combo with or
without riser attached.

• PVC connector included and easily attaches to

floor drain for added protection

• Dimensions: 29" x 33" interior (31" x 35" exterior)

1.64" deep

• Drain location is 1.75” from edge of tray. Drain

exit fitting mates to a 1-1.5” PVC pipe.

1. Remove the floor pan from the packaging.

2. Place it in the final installation location and attach
the drain fittings if so desired.

3. Install the Combo onto the pan being careful not
to damage the unit r tray. It may help to tip the
unit slightly to slide it over the pan lip and slide
into the final location.

TOUCH-UP PAINT WR97X27706

0.6OZ. BLACK SLATE / CARBON GRAPHITE

• Precision Color wet paint designed specifically to
match your appliance appearance surfaces.

• WR97X27706 Color has been formulated to

hide / fill scratches on the Combo’s metal and

plastic panels.

• Applicator brush integrated into the cap.

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 11

1’ HOSE SPLITTER 2 WAY WX14X10014

SHORT HOSE with Y-ADAPTER (2 NEEDED)

• Provides ability to split either the HOT or COLD
water supplies. Two kits requires for this installation.

• Kit includes: 1’ stainless steel hose, y-adapter with
male threaded connections, two rubber washers.
Compatible with rubber or stainless steel hoses.

1. Remove the hose from the pack and install the
rubber washers in each end. Install the top end of
the y-adapter onto one end of the hose.

2. Assemble the open end of the hose onto either the
HOT or COLD water faucet. It may help to label this
hose to recall if HOT or COLD is the input.

3. Tighten, but do not overtighten, the fitting at the
faucet.

4. Repeat steps 1-4 for the second kit.

5. Using 2 sets of supply hoses – total of 4 four (sold

separately) for the Combos, attach the hoses to the

y-adapters, making sure to separate one set of HOT
and COLD for each Combo.

6. Connect hoses to each Combo, ensuring to attach
HOT to HOT (red) and COLD to COLD (blue).

7. Tighten, but do not overtighten, all the fittings.

8. Turn on the faucets slowly, checking for leaks. If
needed, reinstall any hoses/fittings.

9. Next, check the sizing of your standpipe and

confirm that the diameter is at least 2.0” and that

the opening is between 24 - 96” off the floor.

10. Install the first drain tube into the standpipe,
inserting it between 4 – 7” into the pipe.

11. Install the second Combo’s drain tube 4-7” into the
standpipe next to the other drain tube. If the ID of

the pipe is at least 2” , they should pass each
easily. If the ID is closer to 1.5”, you may need to

initially squeeze one tube to get the rubber end

into the pipe to get it started.

12. Secure each drain tube properly using zip-ties so
that they do not move during usage.

x 2

12 | GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com

240V PLUG CONVERTER GFAPC120V

4-PRONG 240V TO 110V PLUG ADAPTER

• 4 prong 240V plug converter for two 110V outlets

• 14-30P plug, with QVNU2 supplementary

protection

• Intended for use with electric 110V 15 A Combo

• One alternative to the GFAPC120V part (available

late 2023) is:

1. Confirm that your 240V outlet is functioning
properly and is compatible with a 4 prong
NEMA plug.

2. Install the adapter into the 240V outlet and make
sure it is firmly in place. Based on the orientation
of the outlet, the extensions of the converter may
point to any direction.

3. Install the Combo’s 110V cord into one of the two
extension outlets.

4. If desired, a second Combo unit can be installed
using the second dedicated outlet.

5. When moving the Combos into their final

location, ensure that you do not unplug or
interfere with these cords.

Watch the installation
video if you need further
assistance.

ONETAC 1.5FT NEMA 14-30P 4-PRONG

240V TO 120V 20AMP POWER CORD

ADAPTER W/ CURRENT PROTECTOR

GE PROFILE UltraFast Combo Accessories Guide | www.geappliances.com | 13

For more information

www.geappliances.com/ge/connected-appliances/ultrafast-2-in-1-washer-dryer-combo

GE Appliances

4000 Buechel Bank Road
Louisville, KY 40225
800-GE-CARES

www.geappliances.com

NO load transfer

2 jobs in 1

Wash + Dry

in 1 machine

50% More Energy
Efficient Drying**

w/ Ventless Heat Pump

GE Profile UltraFast Combo with Ventless
Heat Pump Technology Washer/Dryer

PFQ97HSPVDS