Georg Fischer 9900-1BC Specifications

T

Signet 9900-1BC Batch Controller System

Member of the SmartPro™ Family of Instruments

The Signet 9900-1BC Batch Controller system
provides control capability and process fine­tuning in a familiar package. The programming
interface uses a four-button keypad and an intuitive
menu for adjusting a batching system to the best
performance possible. Choose between simple or
advanced modes. In simple mode, relay outputs
can be used for batching, external counter, missing
signal alarm and 4 to 20 mA output can be used
to indicate batch status. In advanced mode relays
can also be used for end of batch pulse, two-stage
shutdown, overrun alarm, high flow detection, total
volume or source volume alarm.

Features

• Store up to 10 batch sizes for batching or
blending a variety of liquid volumes

• Customize 10 batch names for easy
distinction between batches

• Modular Design - Can be purchased as a
complete system or add a Batch Module and
Relay Module to an existing 9900 Transmitter
(Generation II)

• Remote control wiring with start, stop &
resume terminals for remote batch control

• 3 programmable relays

• Two-stage control to prevent overfilling or
to minimize water hammer

• Confirmation START/RESUME – Can prompt
user prior to starting each batch with a Yes/No
or password to prevent inadvertently starting
a batch

• Enter 10 different K-Factors - one per batch
for when different liquids are batched

MEASURING EQUIPMEN

77CJ

Designed for a variety of batch applications, the
9900-1BC can save up to 10 batch sizes for batching
or blending a variety of liquid volumes. Customize
batch names for easy distinction between batches.
One K-Factor can be used for all batches, or
use a different K-Factor for each batch for when
different liquids are batched. User can choose to be
prompted prior to starting a batch with a Yes/No or
with a password to prevent inadvertently starting a
batch.

The 9900-1BC operates on 10.8 to 35.2 VDC,
regulated. Connect a remote start or stop switch for
remote batch control. Use the end-of-batch pulse
to trigger the next step in the process.

Applications

• Batch Process

• Filter Backwash Initiation

• Chemical Addition

• Canning and Bottling

U.S. Patent No.: D662,844 S
Taiwan Patent No.: D147,150

Specifications

General

Input Channels One
Accuracy ±0.2%
Terminal Blocks Pluggable screw type 14 AWG max wire gauge

Enclosure and Display

Case Material PBT
Window Shatter-Resistant Glass
Keypad 4 buttons, injection-molded silicone rubber seal
Display Backlit, 7- and 14-segment
Indicators Dial-type digital bar graph
Update Rate 1 s
LCD Contrast 5 settings
Enclosure Size ¼ DIN
Mounting Panel ¼ DIN, ribbed on four sides for use with mounting bracket for panel mount installations

Wall Large enclosure (sold as an accessory) that encases the panel mount transmitter

Environmental

Ambient Operating Temperature
Backlit LCD -10 °C to 70 °C 14 °F to 158 °F
Storage Temperature -15 °C to 70 °C 5 °F to 158 °F
Operating Temperature -10 °C to 70 °C 14 °F to 158 °F
Relative Humidity 0 to 100% condensing for front only; 0 to 95% non-condensing for back side
Maximum Altitude 4,000 m (13,123 ft)
Enclosure Rating Designed to meet NEMA 4X/IP65 (front face only)

Input Power

DC 24 VDC input; range: 10.8 to 35.2 VDC regulated 300 mA maximum
Overvoltage Protection 48 Volt transient protection device
Current limiting for circuit protection
Reverse-Voltage Protection

Input Specifications

Digital (S
Accuracy Determined by sensor
Frequency

Power to Sensors

Power Supply

3

L) Serial ASCII, TTL level, 9600 bps

Sensitivity
Range
Accuracy

80 mV @ 5 Hz, mV threshold gradually increasing with frequency

0.5 Hz to 1500 Hz @ TTL level input for open collector
± 0.5% of reading max error @ 25 °C

Repeatability ± 0.2% of reading
Resolution 1 μs
Update Rate 150 ms nominal

Voltage +4.9 to 5.5 VDC

@ 25 °C, regulated

Current 20 mA max.
Short Circuit Protected

Reverse Polarity Protected

www.gfsignet.com

Specifications continued

Output Specifications
Relay Specifications

Dry-Contact Relays (2) Open Collector (1)
Type SPDT NPN
Form C N/A
Max. Voltage Rating 30 VDC or 250 VAC 30 VDC
Max. Current Rating 5 A 50 mA

Hysteresis Adjustable (absolute in Engineering Units)
Latch Reset in test screen or view mode
Delay 9999.9 seconds (maximum)
Test Mode Set On or Off
Maximum Pulse Rate 400 pulses/minute
Volumetric Pulse Width 0.1 s to 3200 s

4 to 20 mA

ANSI-ISA 50.00.01 Class H (passive)

Current Loop Output

Output 1
Span 3.8 to 21 mA
Zero 4.0 mA factory set; user programmable from 3.8 to 4.2 mA
Full Scale 20.00 mA factory set; user programmable 19.0 to 21.0 mA
Accuracy

± 32 μA max. error @ 25 °C @ 24 VDC

Resolution 6 μA or better
Temperature Drift ± 1 μA per °C
Power Supply Rejection ± 1 μA per V
Isolation

Low voltage (< 48 VAC/DC)

Voltage 10.8 to 35.2 VDC
Max. Impedance

250 Ω @ 12 VDC 500 Ω @ 18 VDC 750 Ω @ 24 VDC

Update Rate 150 ms nominal
Short circuit and reverse polarity protected
Adjustable span Reversible
Error Condition Selectable error condition 3.6 or 22 mA or NONE
Actual update rate determined by sensor type
Test Mode Increment to desired current (range 3.6 to 21.00 mA)

Shipping Weights

Base Unit 0.63 kg (1.38 lb)
Batch Module 0.16 kg (0.35 lb)
Relay Module 0.19 kg (0.41 lb)

Standards and Approvals

CE, UL, CUL, FCC

RoHS compliant, China RoHS

Manufactured under ISO 9001 for Quality, ISO 14001 for Environmental Management

and OHSAS 18001 for Occupational Health and Safety

Dimensions

99.06 mm
(3.90 in.)

29.97 mm
(1.18 in.)

www.gfsignet.com

99.06 mm
(3.90 in.)

8.13 mm
(0.32 in.)

91.44 mm
(3.60 in.)

54.10 mm
(2.13 in.)

Signet Model 9900-1BC Batch Controller System

(Includes mounting bracket and panel gasket)

Signet Sensors - Flow

FLOW

System Overview

525

2000

515

2536

Panel Mount - Tank, Wall

Signet Model 9900-1BC Batch Controller System

with Wall Mount Accessory

2100

2507

2537

2540

+

3-9900.392

2551 2552

Signet Fittings - See individual sensor data sheets

Ordering Information

Mfr. Part No. Code Description

3-9900-1BC 159 001 770 Batch Controller System

3-9900-1P

159 001 695 9900 Panel Mount Transmitter

3-9900.393 159 001 698 Relay Module - 2 DCR (dry-contact relays)
3-9900.397 159 310 163 Batch Module

Accessories and Replacement Parts

Mfr. Part No Code Description

6682-1102 159 001 710 DC Power Plug, 2 Pos, Right Angle
6682-1103 159 001 711 Relay Module Plug, 3 Pos, Right Angle
6682-1104 159 001 712 Loop Power Plug, 4 Pos, Right Angle

3

6682-3004 159 001 725 Freq/S
6682-3104 159 001 713 Freq/S
7300-7524 159 000 687 24 VDC power supply 7.5 W, 300 mA
7300-1524 159 000 688 24 VDC power supply 15 W, 600 mA
7300-3024 159 000 689 24 VDC power supply 30 W, 1.3 A
7300-5024 159 000 690 24 VDC power supply 50 W, 2.1 A
7300-1024 159 000 691 24 VDC power supply 100 W, 4.2 A
3-9900.390 159 001 714 Standard Connector Kit, Right Angle
3-9900.391 159 001 715 Connector Kit, In-Line
3-9900.392 159 001 700 Wall Mount Accessory
3-9000.392-1 159 000 839 Liquid Tight Connector Kit, NPT (1 pc.)

L Plug, 4 Pos, In-Line

3

L Plug, 4 Pos, Right Angle

All sold separately

3-9900-1BC.099 Rev A (02/13)

© Georg Fischer Signet LLC
3401 Aero Jet Avenue, El Monte, CA 91731-2882 U.S.A. • Tel. [phone] • Fax [phone] • www.gfsignet.com • e-mail: [e-mail]
Specifications subject to change without notice. All rights reserved. All corporate names and trademarks stated herein are the property of their respective companies.