Page 1
Label Picture Description QTY
A Chair Base 1
B Chair Backrest 1
C Seat Cushion 1
Assembly Instructions
Caution: You must read this before you proceed
Chair
Parts List
Page 1 OF 12
Page 2
D Left Arm Board 1
E Right Arm Board 1
F Arm Pillow 2
G Wooden Leg 4
Label Picture Description QTY
①
Bolt
(M6*60mm)
9
② Washer 10
③ Spring Washer 10
④
Double-threaded Bolt
(M8*60mm)
1
⑤ Wing Nut 1
⑥ Allen Key 1
Hardware List
Page 2 OF 12
Page 3
⑦ Gasket 7
Before Begining
Assembly:
Assembly Preparation
Page 3 OF 12
Page 4
Step 1
Assembly Steps
This Chair has multiple parts and may require about 30 minutes to assemble. To give you an
overview of the Chair parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the parts
and steps before assembly.
Take the Chair Base(A), Chair Backrest(B), Seat Cushion(C), Left Arm Board(D), Right Arm
Board(E), Arm Pillow(F) and Small Box out from the carton and place them on a clean, nonmarring surface.
Arm Pillow (F)
FRONT FACING
Chair Backrest (B)
Chair Base (A)
Left Arm (D)
Seat Cushion (C)
Wooden Leg (G)
Right Arm (D)
A
C
D
E
B
F
Small Box
Arm Pillow (F)
Page 4 OF 12
Page 5
Step 3
Step 2
Open the Small Carton Box to take out the Wooden Legs(G), Gaskets(⑦), Bolts(①),
Washers(②), Spring Washers(③), Double-threaded Bolts(④), Wing Nuts(⑤), and Allen
Key(⑥).
Carefully peel the back non-woven cover under the Chair Base(A) and to take out the other
Arm Pillow(F).
①
Small Box
③
④
⑥
⑤
⑦
G
②
A
F
Hardware and
Legs inside
Page 5 OF 12
Page 6
Step 4
Turn the Seat Base(A) facedown.
Carefully peel back the left and right non-woven cover under the Seat Base(A) to expose the
mounting positions.
A
Page 6 OF 12
Page 7
Step 5
5.1) Align Left Arm Board(D) with the left side of the Chair Base(A).
5.2) Attach Left Arm Board(D) to Sofa Base(A) using Bolts(①), Spring Washers(③), and
Washers(②) with Allen Key(⑥).
Tighten the Bolts fully in a sequential manner.
D
⑥
A
D
A
②
①
③
5.1
5.2
Page 7 OF 12
Page 8
Step 6
6.1) Align Right Arm Board(E) to the right side of the Chair Base(A).
6.2) Attach Right Arm Board(E) to Sofa Base(A) using Bolts(①), Spring Washers(③), and
Washers(②) with Allen Key(⑥).
Tighten the Bolts fully in a sequential manner.
⑥
A
E
E
D A
②
①
③
6.1
6.2
Page 8 OF 12
Page 9
Step 7
Step 8
Locate the mounting position under the Chair Backrest(B), then insert Double-threaded
Bolt(④) into the mounting position and tighten clockwise by hand.
With assistance from your adult partner, hold up the Chair Backrest(B), while standing behind
the Chair Base(A).
Align the mounting brackets on both sides of the Chair Backrest(B) with those on the Left
Arm Board(D) and Right Arm Board(E).
Then slide Chair Backrest(B) downward and while inserting the Double-threaded Bolt(④) into
the mounting position on Chair Base(A) by hand to make sure it locks into place as pictured
A
D
E
B
④
B
B
④
④
Page 9 OF 12
Page 10
Step 9
Open the back non-woven cover under Chair Base(A).
You will see one mounting position on the back panel of the Chair Base(A).
Then, place Washer(②) and Spring Washer(③) onto the Double-threaded Bolts(④), and
secure using Wing Nut(⑤).
Tighten the Wing Nut fully by turning it clockwise by hand.
②
③
⑤
④
A
A
B
D
E
Page 10 OF 12
Page 11
Step 10
Step 12
Install the Wood Legs(G) at the bottom of the Chair by placing one Gasket(⑦) on the
threaded stem.
Then insert threaded stem into the mounting postion at the corner of the Chair.
Tighten by turning the Leg clockwise.
Note: The use of Gaskets are OPTIONAL and are especially useful to help alleviate
slight wobbleness. Some Legs may need more than one Gasket whilst some Legs may
not need any.
Put the Seat Cushion(C) on the Chair Base(A).
Place Arm Pillows(F) against Left Arm Board(D) and Right Arm Board(E).
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Step 11
G
G
C
F
F
Page 11 OF 12
Page 12
Page 12 OF 12
Loading...