Page 1
Label Picture Description QTY
A Leg 1
Assembly Instructions
Caution : You must read this before you proceed
DINING CHAIR
Part List
WARNING: These chairs are intended only for normal use with all four chair
legs on the ground. These consumer chairs have relatively thin legs and are
not designed to be sat in with only two chair legs on the ground (as from
tipping back, forward, or to the side), and such can cause stress and failure
of one or more chair legs. Any misuse of the chairs voids any warranties,
express or implied.
Page 1 of 8
Page 2
B Leg 1
C Backrest 1
D Seat 1
E Corner Block 2
Label Picture Description QTY
① Short Bolt Set 4
② Long Bolt Set 4
③ Screw (M7 x 40mm) 1
④ Screw 8
⑤ Allen Key 1
⑥ Screwdriver
(Not
Provided)
Hardware
Assembly Preparation
Page 2 of 8
Page 3
Before
Beginning
Assembly:
Assembly Steps
Overview
This Dining Chair has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Dining Chair parts, the above
picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and
steps before assembly.
Assembly Steps
Backrest (C)
Leg (B)
Seat (D)
Leg (A)
Page 3 of 8
Page 4
Step 1
Step 2
Thread together Leg(A) into Leg(B) as shown in the picture.
Place the Legs(A & B) onto the Seat(D) as shown.
Attach Legs(A & B) to Seat(D) using Long Bolt Sets(②) with Allen Key(⑤).
Do not fully tighten the Bolts.
Page 4 of 8
Page 5
Step 3
Step 4
Fix the Legs(A & B) to Seat(D) using Screw(③) with Allen Key(⑤).
Do not fully tighten the Screw.
Attach Backrest(C) to Legs(A & B) using Short Bolt Sets(①) with Allen
Key(⑤).
Do not fully tighten the Bolts.
Upper
Down
(BACKREST POSITION)
Page 5 of 8
Page 6
Step 5
Step 6
Place the Corner Block(E) at the center of Legs(A & B) as shown.
Then, attach the Corner Block(E) to Legs(A & B) using Screws(④) with
Screwdriver(⑥).
Repeat this process with the three remaining Corner Blocks.
Do not fully tighten the Screws.
① If wobble
③ Test again
②
30-50mm
Page 6 of 8
Page 7
Step 7
Place the Dining Chair on a Level Surface to check if it wobbles.
If it wobbles, lift the Dining Chair some 30cm to 50cm high from the ground,
keep your feet and toes well away from the drop zone, and drop the Dining
Chair freely and vertically with the four legs, hitting the ground at the same
time.
This Drop Test will help to ensure that all the Bolts, Screws and gaps reach
full alignment.
Test again for evenness on Level Surface.
If no wobbles are found, proceed to tighten all the Bolts and Screws.
When tightening the Bolts and Screws, tighten sequentially.
Do not tighten any Bolt or Screw fully and then move on towards the
next one, this could cause the frame to warp. If it still wobbles, loosen
the Bolts and Screws and execute this same drop test.
If the Dining Chair is not Stable it could lead to damage to the product.
Inspect and make sure all parts are fully connected.
Your Dining Chair is ready for use.
This Dining Chair can only be used on a flat, level surface.
Page 7 of 8
Page 8
Page 8 of 8
Loading...