Page 1
Caution: You must read this before you proceed.
SOFA
1 of 8
Page 2
Label Picture Description Qty
A Backrest 1
B1
B2
Left Arm
Labeled "B1"
Right Arm
Labeled "B2"
1
1
C Seat Frame 1
D Leg 5
Label Picture Description Qty
①
②
③
④
⑤
⑥
⑦
Washer Ring 7
Spring Washer 9
Flat Washer 9
Screw Arbor 3
Butterfly nuts 3
Bolt (M8*55mm)
Allen Key 1
5
2 of 8
Page 3
OVERVIEW
Left Arm(B1)
Backrest (A)
Right Arm(B2)
Leg (D)
Seat Frame(C)
Leg (D)
Leg (D)
3 of 8
Page 4
This SOFA has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the SOFA parts, the above picture is to help you put the various
SOFA parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
Step 1
Right Arm(B2)
Left Arm(B1)
Position the Seat Frame(C) on its back,as shown.
Unzip to open pouch and remove the 5 wooden legs and Hardware, left arm and right arm
,close the pouch.
Step 2
Right Arm(B2)
Seat Frame(C)
Left Arm(B1)
②
⑥
③
⑦
Align the Left Arm(B1) and Right Arm(B2) to the Seat Frame(C) using Bolt(⑥),Flat Washer(③),
Spring Washers(②) with Allen Key(⑦) as shown.
4 of 8
Page 5
Step 3
Step 3.1
Step 3.2
Backrest (A)
④
Backrest (A)
Seat Frame(C)
Step 3.1 Screw-in the short end of Screw Arbor(④) into Backrest(A) , by hand, turning clockwise
as shown.
Step 3.2 Insert Backrest(A) into Seat Frame (C) in the down direction as shown.
Step 4
⑤
②
④
③
Seat Frame(C)
Lay the Sofa on a flat surface as shown.
Connect Backrest(A) with Seat Frame(C) using Screw Arbor(④),Flat Washer(③), Spring
Washers(②) with Butterfly nuts(⑤) as shown.
Tighten Butterfly Nuts at joints in a sequential manner until fully secure.
5 of 8
Page 6
Step 5
Step5.1
Seat Frame(C)
Step5.2
Washer Rings(①)
Legs(D)
Step 5.1 Cover the bottom of the Seat Frame(C) with the non-woven fabric.
Smooth down the Magic Tape on all four sides of the Seat by hand. as shown
Step 5.2 Install the Legs(D) into the bottom of the Left Arm(B1) and Right Arm(B2) and Middle
of the Seat Frame by placing a Washer Rings(①) onto the threaded stem of the Legs.
And then insert the threaded stem into the threaded mounting position at each Corner of the
Bottom Left Arm(B1) and Right Arm(B2).
Tighten by turning the Legs clockwise.
Note: The use of Washer Rings(①) are OPTIONAL and are especially useful to help alleviate
slight wobbles.
Some Legs may need more than one Washer Rings(①) whilst some Legs may not need any.
Position Sofa right side up and test for stability on a Level Surface.
Add or remove Washer Rings(①) where needed to achieve stability.
Step 6
6 of 8
Page 7
Add or remove Washer Rings(①) where needed to achieve stability
Note:The use of Washer Rings(①) are OPTIONAL and is especially useful to help alleviate
slight wobbleness.Some Legs may need more than one Washer Rings(①) whilst some Legs
may not need any.
Position Right arm sofa right side up and test for stability.
Step 7
Your SOFA is ready for use.
This SOFA can only be used on a flat, level surface.
7 of 8
Page 8
8 of 8
Loading...