Assembly Instructions
Caution: You must read this before you proceed
Caution: This Loveseat is NOT a TOY.
Keep your child / children at bay in the process of assembly.
Whenever moving or lifting the Loveseat and to prevent damage to the Loveseat, two adults may be
needed to execute these actions
LOVESEAT
1 of 7
Label Picture Description QTY
A-L
Leg 2
B-L Seat Panel 1
C-L
Backrest Panel
1
D-L
Decorative Corner Block 2
E-L Seat Cushion 1
F-L Back Cushion 2
No. Picture Description Qty
①-L Bolt (M8x70mm) 5
②-L
Washer (M8xD2mm) 5
③-L
Screw
(M6x80mm)
3
④-L
Screw
(M6x50mm)
5
⑤-L Allen Key 1
Parts List
Hardware
2 of 7
Assembly Steps
Overview
Assembly Preparation
Before Beginning Assembly:
This Loveseat has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Loveseat, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
Back Cushion (F-
L)
Backrest
Panel (C-L)
Leg (A-L)
Seat
Cushion (E-L)
Seat Panel (B-L)
FRONT FACING
Decorative
Corner
Block (D-L)
3 of 7
Unpack and place all parts on a clean, non-marring surface.
2.1) With assistace frorm your adult partners, turn the Seat Panel(B-L) facedown as pictured above.
2.2) Attach Legs(A-L) to Seat Panel(B-L) using Bolts(①-L), and Washers (②-L) with Allen Key(⑤-
L) as shown above.
Do not fully tighten the Bolts.
Step 2
Step 1
2.1
2.2
4 of 7
Insert the Tenons from Seat Panel(B-L) into the Mortises of the Backrest Panel(C-L) then attach
using Screws(③-L) with Allen Key(⑤-L).
Do not fully tighten the Screws.
Step 3
Step 4
Align the Decorative Corner Blocks (D-L) to the mounting position on the Loveseat.
Attach Decorative Corner Blocks (D-L) to Loveseat using Screws(④-L) through the vertical and
horizontal mounting positions with Allen Key (⑤-L) as shown above.
Do not fully tighten the Screws.
5 of 7
Step 6
Step 5
Place the Loveseat on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit into to the Loveseat.
This will help to align all the parts at all joint areas.
Then get off the Loveseat and proceed to tighten the Bolts and Screws in a sequential manner.
When tightening the Bolts and Screws tighten sequentially.
DO NOT tighten any Bolt or Screw fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and Screws and execute this same process.
Place Seat Cushion(E-L) and Back Cushions(F-L) onto the Loveseat.
Tie the velcro straps on the Seat Cushion(E-L) to Seat Panel(B) and Back Cushions(F-L) to
Backrest Panel(C-L).
Your Loveseat is ready for use.
This Loveseat can only be used on a flat, level surface.
6 of 7
7 of 7
Loading...