George Oliver VKGL7627 Assembly Instructions

bed components

bed

Assembly Instructions

(1) headboard*

*images may vary from actual product

(4) 3” x 5/16” bolts (26) 1¼” washers

You will need:

• at head screwdriver

(2) Full/Queen/King/California King

wooden plank rolls

(1) Twin

(18) 2” x 5/16” bolts

*Open all hardware packets
before proceeding

If you have any questions, please call us

(4) legs

for all sizes

LIMITED WARRANTY

We guarantee our upholstered furniture against defects in construction for a period of one (1) year. When a structural defect is brought to our
attention, we will repair or replace it at our option at no charge to the customer (includes parts and labor, not transportation costs). Fabric
wearability for upholstered furniture is not covered by the warranty. Vacuum for regular cleaning.

PLEASE DISPOSE OF PLASTIC BAG (S) AND CARTON (S) RESPONSIBLY.

bed components cont.

(2) side rails

for all sizes

(2) end rails

for all sizes

support legs

(1) Twin

(4) Full

(5) Queen

(6) King/California King

(4) corner brackets

for all sizes

bed hardware

(1) upholstered foot board

for all sizes

horizontal support rail

(1) Twin, Full, and Queen
(3) King and California King

(1) vertical support rail

for Full/Queen/King/ California King

(2) upholstered side rails

for all sizes

1” x ¼” bolts

(5) Twin
(15) Full

(15) Queen

(19) King

(19) California King

(1) wrench

for all sizes

¼” bolts

(10) Twin

(10) Full

(10) Queen

(14) King

(14) California King

(1) 5/32” L wrench

for all sizes

¾” washer

(smaller center)

(1) Twin

(7) Full

(7) Queen

(11) King

(11) California King

¼” nuts

(14) Twin

(21) Full

(20) Queen

(27) King

(27) California King

Step 1

1. Attach side rail and end
rail to corner bracket.
Make sure to align holes
and snap into thinner slot.

Continue this action until
you have a rectangular
frame.

1

2

2. Attach corners to rails using
(8) ¼” bolts and (8) ¼” nuts.

Step 2

Attach wooden legs to
headboard and foot board

* Use a 1¼” washer on each leg
before attaching.

Step 3

1

2

1. Use (4) 3” x 5/16” bolts,
(4) 1 ¼” washers to attach the
headboard to the bed frame.

2. Use (6) 2” x 5/16” bolts,
(6) 1 ¼” washers to attach the
foot board to the bed frame. Do
not fully tighten, as you will
do this later when adding side
rails.

Step 4

2

1. Place side rail in between
the headboard and foot board,
lining up the holes, if too tight
loosen headboard/foot board to
place.

2. Use (6) 2” x 5/16” bolts,
(6) 1 ¼” washers to attach
each side rail to the bed frame.

3. Repeat step 2 for other side
rail.

Step 5

(Queen image displayed)

Step 6

Attach horizontal support rail
using (2) ¼” bolts and
(2) ¼” nuts. Make sure to
attach the horizontal support
rail underneath the bed frame.

Note:
King and California King have 3 horizontal
support rails, and therefore (6) 1/4” bolts and
(6) 1/4” nuts.

(Queen image displayed)

For Full, Queen, King, and
California King, attach vertical
support rail using (2) 1¼”
bolts, (2) small washers, and
(2) ¼” nuts. Make sure to
attach the vertical support rail
above the horizontal support
rail.

Note:
Twin beds do not have vertical rails or extra
support legs.

Step 7

(Queen image displayed)

Attach each support leg to the
horizontal & vertical support
rails using (1) 1” x ¼” bolts and
(1) ¾” washer.

Note:

Twin = 1 support leg
Full = 4 support legs
Queen = 5 support legs
King/California King = 6 support legs.

For Full, King, and Cal King:
Attach vertical support rail to
horizontal support rails using
1” x ¼” bolts, ¾” washers, and
¼” nuts. For Twin and Queen
skip to step 8.

(Full, King, and Cal King image displayed)

Step 8

(Queen image displayed)

Place one of the wooden
plank rolls into the bed frame.
Attach using (4) 1” x ¼” bolts
and (4) ¼” nuts. Repeat for
other side.

Note:
Twin= 1 wooden plank roll
Full/Queen/King/California King =
2 wooden plank rolls