Page 1
ARM CHAIR
Thank you for purchasing the CHAIR！
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Component:
Hardware:
A
B
C
D
Short Bolt M8x65mm x4
Long Bolt M8x75mm x4
Flat Washer M8 x8
Allen Wrench M5 x1
Chair Body x1
1
1
3
2
2
Front Leg x2
2
Page 1 of 4
Back Leg x2
3
Page 2
ARM CHAIR
STEP 1:
Put Chair Body (1) upside down on a carpeted or padded surface.
Open Velcro on the bottom of Chair Body (1) and find the package of Front Legs (2), Back Legs (3) and Hardware as shown.
Package of Front Legs, Back Legs and Hardware
Velcro
STEP 2:
Make the position for assembling Front Legs (2) and Back Legs (3) fully visible.
Place 2 pieces of Back Legs (3) to the back position of Chair Body (1) as shown.
Insert 2 pieces of Short Bolt (A) with 2 pieces of Flat Washer (C) into the bottom pre-drilled holes on Back Legs (3)
through the bottom pre-drilled on the back of Chair Body (1).
Insert 2 pieces of Long Bolt (B) with 2 pieces of Flat Washer (C) into the top pre-drilled holes on Back Legs (3) through
the top pre-drilled on the back of Chair Body (1).
Use Allen Wrench (D) to tighten Short Bolts (A) and Long Bolts (B). Do not fully tighten the Bolts (A&B) at this step.
D
D
B
A A
3
B
A C C
C
C
3
A
B
3
C
1
Ax2 Bx2
Cx4
C
1
Dx1
Page 2 of 4
Hardware & Tools required
Page 3
ARM CHAIR
STEP 3:
Place 2 pieces of Front Legs (2) to the front position of Chair Body (1) as shown.
Insert 2 pieces of Short Bolt (A) with 2 pieces of Flat Washer (C) into the bottom pre-drilled holes on Front Legs (2)
through the bottom pre-drilled on the back of Chair Body (1).
Insert 2 pieces of Long Bolt (B) with 2 pieces of Flat Washer (C) into the top pre-drilled holes on Front Legs (2) through
the top pre-drilled on the front of Chair Body (1).
Use Allen Wrench (D) to tighten Short Bolts (A) and Long Bolts (B). Do not fully tighten the Bolts (A&B) at this step.
D
D
3
A
C
3
B
C
2
A
C
B
C
2
A
C
B
C
2
1
1
Ax2 Bx2
STEP 4:
Carefully turn over the assembled chair .
Please put a heavy object or seat one adult on top of the assembled Chair to pressure the chair for leveling.
Turn upside down again, then use Allen Wrench (D) to tighten Short Bolts (A) and Long Bolts (B) clockwise until secure.
Cx4
Dx1
Hardware & Tools required
D
Dx1
Page 3 of 4
Hardware & Tools required
Page 4
ARM CHAIR
STEP 5:
Carefully cover the bottom of Chair Body (1) by Velcro as shown.
STEP 6:
Carefully turn over the assembled Chair.
Assembly is complete. Your chair is ready to be used now!
Page 4 of 4
Loading...