Genoss ICT Injection SE User Manual
www.genoss.com
English
User Manual
www.genoss.com
Dear Customer
iCT injectionSE by GENOSS is an anesthesia solution injecting instrument during surgical procedures. Its injecting speed can be adjusted to help a
surgery safely and accurately. Please read through this user manual before using the product to ensure safe and proper use.
If you have any enquiries, please contact your service provider.
Contents
1. Attention
2. Package Contents
3. Technical Information
4. Device Layout
5. Product Assembly and Disassembly
5.1 Charging the Product
5.2 Anesthesia cartridge holder and a Needle
5.3 Anesthesia cartridge
2
04
05
06
07
08
08
10
12
6. Function
6.1 Buttons
6.2 Announcements and Displays
6.3 Charge Display
6.4 Operation
7. Important notes
8. Cleaning and Storage
8.1 Cleaning
8.2 Storage
9. Maintenance
10. Trouble shooting
11. Label
12. Warranty
14
14
15
16
16
18
19
19
19
20
22
24
27
3
1. Attention
▶ Special attention is marked with [ Warning!] sign.
▶ iCT injectionSE is to be used only by doctors and specialists.
▶ Plaese read thorough this manual before using the device to ensure safe and proper use.
▶ Assemble/Disassemble the ampoule holder and the needle only when the device is OFF.
▶ Please note that damages occurred due to user’s deliberately forced disassembly of the device are not
covered by the warranty.
▶ The device can be damaged if it is dropped or exerted much force.
▶ If there is any abnormality with the device, please stop using the device immediately and contact your service provider.
4
2. Package Contents
www.genoss.com
User Manual
English
www.genoss.com
User Manual
Charger Cradle Adaptor AC Cord
Caution!
Anesthesia cartridge holder and rechargeable battery are consumable goods.
Anesthesia Ampoule Holder 3ea
Main Body
5
3. Technical Information
Main Body
Charger Cradle
Anesthesia Cartridge Holder
Injection Level Manual mode 3steps
Total Injection Amount 1.8ml
Electrical Power Source
Use Condition Temperature: 10~40℃ / Relative humidity: Max. 80%
Free Warranty 1 year
Product cycle 3 years
6
Weight: 72g / Size: 150(W) x 22.4(D) x 30(H)mm / Material: ABS resin
Weight: 40g / Size: 71(W) x 62(D) x 46.5(H)mm / Material: ABS resin
Weight: 7g / Size: 7(Ø) x 86.3(H)mm / Material: PEI resin (able to sterilize)
Body
Charger Cradle
Adapter
3.7V 470mAh Lithium Polymer (Protection circuit equipped)
Input: DC 12V/1A
Input: AC 100~240V (50/60Hz) / Output: DC 12V/1A
[Table-1]
4. Device layout
①
②
④
③
⑧
⑤
⑦
⑥
⑩
[Figure-1]
Caution!
If a product defect occurred by using for unintended purpose, randomly disassemble or modied by the user,
the repair service will not be covered by the warranty.
⑨
No. Name
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
Power Button
Injection Button
Stop Button
Display Panel
Anesthesia Ampoule Holder
Speaker
Charge Display
DC jack
DC Plug
AC Cord
[Table-2]
7
5. Product Assembly and Disassembly
5.1 charging the Product
▶ Connect the power cord to AC adapter rmly then insert them into the DC jack on the charger cradle.
▶ Full charging takes 8 hours at the rst time after purchasing this product.
[Figure-2]
8
5. Product Assembly and Disassembly
▶ Main body will be inserted at the same direction as shown in the [Figure-3]. The chargedisplay will be turned on when the battery is
charging, and turned o when the main body is taken out after fully charging.
▶ Refer the [Figure-5] for the color of charge display.
Caution!
Use only approved chargers, batteries, and cables. Unapproved charges or cable can causethe battery explode or damage the device.
[Figure-3]
9
5. Product Assembly and Disassembly
5.2 Anesthesia Cartridge holder and a needle.
▶ Assemble of Anesthesia ampoule holder: The ampoule holder should be tightly installed at the front of the main body and turned 90 degrees to
the right (clockwise) as shown in the [Figure-4]. Disassembly will be done by reverse order of installation process.
[Figure-4]
10
Loading...