Genlantis SteriZAP User Manual

Specifications

Unit Dimensions (

W x D x H) 16 x 13.5 x 46.75 inches

(40.6 x

34.3 x 118.75 cm)

Lamp Power

and Life

55

W per lamp (4 lamps total)

/ 9,000 hours average life

Weight

44 lbs (20 kg)

Operating Modes

2 or 4 lamps at a time,

15-minute increments up to 23 hours 45 minutes.

Warranty

1 year

#

SteriZAP® UV

-

C Room Sterilizer

Keys x 2

SteriZAP® UV

-

C Room Sterilizer

Keys x 2

Related Products

Catalog #

FirstResponder® Sterilizer, 110V (Ozone)

E4110FRS

SteriZAP® Handheld UV

-

C Sterilizer, 110V

E500UVCH

SteriZAP® Portable UV

-

C Sterilizer

E500UVCP

SteriZAP® Electrostatic Backpack Sprayer

E700EBS

SteriZAP® Germicidal Sprayer

E800GSP

E400110

E400220

UV-C Room Sterilizer Stainless Steel

Catalog

E500UVST

E520UVST

INTRODUCTION

Description Content

Sterilizer Unit x 1

Stainless Steel, 110V

Stainless Steel, 220V

Remote Control x 1

Sterilizer Unit x 1
Remote Control x 1

FirstResponder® O3 Nest Sterilizer, 110V

FirstResponder® O3 Nest Sterilizer, 220V

UV light is electromagnetic radiation with wavelengths shorter than visible light. UV can be separated
into various wavelength ranges, with the short-wavelength UV, or UV-C considered to be germicidal.
Furthermore, and at the specific wavelength range of 260 to 270 nm, UV-C is found to be mutagenic to
bacteria, viruses and other microorganisms. Germicidal UV-C kills or inactivates microorganisms by
destroying their nucleic acids and disrupting their DNA, leaving them unable to perform vital cellular
functions.

The SteriZAP® UV-C Room Sterilizer Stainless Steel harnesses the germicidal power of UV-C light, in
particular in the 254 nm wavelength. This unit uses shortwave UV lamps that emit ultraviolet light with
the major peak output (~90%) band at 253.7 nm. The doped fused quartz glass tubes of the SteriZAP®
lamps pass the 254 nm radiation (which produces very low ozone levels) but blocks the 185 nm
wavelength (which produce higher ozone levels). The SteriZAP® UV-C Room Sterilizer Stainless Steel
is intended for use in disinfection of surfaces in laboratories, hospital rooms, food-processing areas, or
any other places where disinfecting and sterilizing are desired.

Electrical Specifications 110 volts AC, 60 Hz (±10%) for E500UVST; 220 volts AC, 50 Hz (±10%) for E520UVST

UV Output / Dosage ≥ 428 µWs/cm2 at 1 foot; ~90 µWs/cm2 at 6 feet, ~32 µWs/cm2 at 12 feet

Safety Feature Motion sensor shut-off.

PRECAUTIONS AND WARNINGS

(a) Read all instructions before using the devices. Use of these devices is only for intended purposes as described in this manual.
(B) DO NOT ATTEMPT TO OPERATE THE DEVICE IN THE PRESENCE OF PEOPLE OR ANIMALS.
(C) FOR SAFE AND PROPER OPERATIONS, DO NOT TAMPER WITH THE UNITS IN ANY WAY.

(d) The SteriZAP® UV-C Sterilizer Stainless Steel emits a small amount of ozone gas when operating, which may give off an odor. This is normal; to eliminate this, briefly

aerate the area.

(e) Do not operate the device if the cord or plug is damaged, if it is not working properly, or if the unit has been damaged or dropped.
(f) Do not store the device outdoors, or use it near open water– for example near filled sinks or water baths.
(g) Do not attempt to repair or open the unit unless you are a qualified repair technician.
(h) To avoid injury, handle broken lamps carefully by using protective hand, body, face, and eyewear. Dispose of broken glass in specialized sharps containers and obey all

applicable country and city laws.

SAFETY NOTIFICATION:

UV-C radiation can damage the superficial tissues of the eye, and care must be taken to avoid excessive exposures to eyes. Glass or plexiglass eyewear
or face mask can provide protection in case the motion sensor safety shut off malfunctions. Also, extended exposure of exposed skin to UV-C make cause
damage to cellular or tissue DNA and should be avoided by wearing protective clothing while near operating UV-C lamps.

Note and Disclaimer

*The SteriZAP® UV-C Sterilizer Stainless Steel is not a replacement or substitute for good cleaning practices. Areas to be sterilized must be free of excess contaminants, especially
any visible liquids or solids (for example bodily fluids, debris or dirt). The SteriZAP® Sterilizer Stainless Steel can eliminate or reduce residual surface contaminants, especially

bacterial and fungal, but only if the UV-C light is able to directly impact the contaminated surfaces. Any surfaces or items that are covered or are behind curtains, glass panels
or plastic sheeting will not be sterilized by the SteriZAP® UV-C unit. Genlantis makes no claims and offers no guarantees of any kind that the SteriZAP® UV-C Sterilizer

Stainless Steel will eliminate or reduce all contaminants and under all possible circumstances. For best results, users should closely follow the recommended instructions below.

SteriZAP® UV-C Room Sterilizer SS Manual

Digital display

DOSAGE RECOMMENDATIONS

Different germs and contaminants are susceptible to UV-C radiation at different rates. To determine the amount of time needed for sterilization,
consult Table 1 on Page 4, and follow these recommendations:

Area coverage is typically determined by the UV lamp wattage. A 15-watt lamp will cover approximately 100 square feet; the SteriZAP’s 220­total lamp watts can theoretically cover an area of about 1,466 square feet, but we recommend only covering an area of about 700 square
feet, which translates into a radius of about 15 feet from the SteriZAP® UV-C Sterilizer device (see below for further explanation).

For sterilization time, it is recommended to use the minimum time needed to kill the most difficult organisms at the farthest distance from the
device. For example, Table 1 (page 4) shows that Aspergillius niger requires 330,000 µWs/cm2 for a 99% kill rate.

The SteriZAP UV-C Room Sterilizer has the following measured outputs: ≥ 428 µWs/cm2 at 1 foot; 90 µWs/cm2 at 6 feet, 32 µWs/cm2 at 12
feet; 18 µWs/cm2 at 15 feet; and 2 µWs/cm2 at 16.5 feet.

To eradicate Aspergillius niger 15 feet away from the device, 5 hours or run time are needed (330,000/18); at 12 feet it becomes 2.9 hours
(330,000/32). This extreme example is used to demonstrate how to calculate distance and time requirements.

Special Note On Covid-19 Sterilization: Because the COVID-19 virus (SARS-CoV-2) is so new, the scientific community doesn’t yet have a

specific deactivation dosage. However, we know the dosage values for comparable viruses in the same SARS virus family are 10-20 µWs/cm2
using direct UVC light at a wavelength of 254nm; this dosage will achieve 99.9% disinfection (i.e., inactivation) under controlled lab conditions.
In real-life, the virus is often hidden or shaded from direct UVC light, reducing UVC’s effectiveness. To compensate, researchers are applying
dosages of 1,000 - 3,000 µWs/cm2 to ensure 99.9% deactivation, the current CDC disinfection goal.

OPERATION

1. Select area to be sterilized and place the SteriZAP® UV-C Room Sterilizer Stainless Steel in the most central area, or nearest to the most

contaminated area. Pre-clean the area if excessive contamination is present.

2. Use one of the provided keys to unlock the side arms, then unlatch them and pull the lamps out and up 0using the built-in arm handles. Lift the
arms up to position them at the desired angles. For low or ground level sterilization, keep arms near the horizonal position. For standard bench
surfaces, a 45

ᴼ

angle from vertical would be the most effective.

NOTE: Avoid using lamp arms to move the SteriZAP unit. This will cause the arms to brake at the top pivot point and cause unit

failure and expensive repairs.

3. Plug power cord into wall outlet; the digital display will undergo a
brief count up and the digital display will show a colon (:) only.

I-Control Pad Operation

4. Press the Time Select Button repeatedly to set the correct

(Hours:Minutes)

SteriZAP™ UV-C Room Sterilizer

Time select
button

Stop button

time. The Time Select Button moves in 15-minute increments, so
for a 1-hour sterilization period, press the Time Select Button four
times.

2 or 4 lamp
selection buttons

5. The unit will start to beep as it counts down to lamp activation (20
beeps, or ~20 seconds); during this time, select one of these
options:

Image 2: SteriZAP™ UV-C Room Sterilizer Control
Pad.

a. to activate both the left and right arms (4 lamps), press both the and buttons simultaneously;

b. To activate the right arm only (2 lamps), press the button;

c. To activate the left arm only (2 lamps), press the button.

6. Exit the room/area. The unit will turn the UVC lamps on after about 20 seconds from the time the motion detector stops detecting movement.
If the unit detects movement during this countdown period, the timer will automatically reset to 20 seconds before turning the UV lamps on.

7. Use copies of page 5 of this manual and affix to the entries or exits of the area being sterilized.

8. During the UV sterilization period, the unit will immediately turn the UV lamps off if motion is detected; the unit will automatically turn the UV
lamps back on 20 seconds after movement stops. To prematurely end sterilization cycles, press the Stop button.

VKM201228 Genlantis Page 2 of 5

6044 Cornerstone Court West, Bldg. E. San Diego, CA 92121  Toll Free [phone]  U.S. & Canada [phone]  www.genlantis.com

2020 Genlantis and Gene Therapy Systems, Inc.

SteriZAP® UV-C Room Sterilizer SS Manual

9. Once the sterilization cycle is finished, the SteriZAP® UV-C Room Sterilizer Stainless Steel will beep for about 10 seconds and the digital

display will show a colon only.

II-Remote Control Operation

10. Press the [ON/TIMER+] button to turn the unit display on; the screen will show a default of 15 minutes (00:15) and
the unit will start beeping to indicate countdown. Press the [ON/TIMER+] button repeatedly to add time (in 15­minute increments) or the [TIMER―] button to decrease time (in 15-minute increments).

a. to activate both the left and right arms (4 lamps), press either the [A] or the [B] button;

b. To activate the right arm only (2 lamps), press the [LIGHT1] button;

c. To activate the left arm only (2 lamps), press the [LIGHT2] button.

11. Exit the room/area. The unit will turn the UVC lamps on after about 20 seconds from the time the motion detector
stops detecting movement. If the unit detects movement during this countdown period, the timer will automatically
reset to 20 seconds before turning the UV lamps on.

12. Use copies of page 5 of this manual and affix to the entries or exits of the area being sterilized.

13. During the UV sterilization period, the unit will immediately turn the UV lamps off if motion is detected; the unit will automatically turn the UV
lamps back on 20 seconds after movement stops. To prematurely end sterilization cycles, press the [OFF] button.

14. Once the sterilization cycle is finished, the SteriZAP® UV-C Room Sterilizer Stainless Steel will beep for about 10 seconds and the digital

display will show a colon only.

MAINTENANCE

The SteriZAP® UV-C Room Sterilizer Stainless Steel is very low maintenance unit and does not require any scheduled or regular cleaning.

(a) Keep unit clean by wiping exterior surfaces with a water dampened towel. To avoid damage, do not use any detergents or solvents.
(b) Do not touch UV-C lamps with bare hands, they will heat up during operation and cause oil or dirt from fingers to leave burn marks and

may cause unpleasant smells. Handle UV-C lamps with gloved hands only.
(c) For optimal performance, keep lamps clean by wiping them occasionally with a dry soft or microfiber cloth.
(d) Unplug the units from the power outlet when the units are in storage or not in use.

VKM201228 Genlantis Page 3 of 5

6044 Cornerstone Court West, Bldg. E. San Diego, CA 92121  Toll Free [phone]  U.S. & Canada [phone]  www.genlantis.com

2020 Genlantis and Gene Therapy Systems, Inc.

SteriZAP® UV-C Room Sterilizer SS Manual

Bacillus anth

r

acis -

Anthrax

4,520 8,700 0.3

Bacillus magaterium sp. (spores)

2,730 5,200 0.2

Bacillus magaterium sp. (veg.)

1,300 2,500 0.1

Bacillus subtilis spores

11,600

22,000

0.9

Bacillus subtilis

5,800 11,000

0.4

Corynebacterium diphtheriae

3,370 6,510 0.3

Leptospiracanicola

- infectious Jaundice

3,150 6,000 0.2

Mycobacterium tuberculosis

6,200 10,000

0.4

Proteus vulgaris

3,000 6,600 0.3

Salmonella enteritidis

4,000 7,600 0.3

Salmonella typhimurium

8,000 15,200

0.6

Shigella dyseteriae

- Dysentery

2,200 4,200 0.2

Spirillum rubrum

4,400 6,160 0.2

Staphylococcus hemolyticus

2,160 5,500 0.2

Vibrio comma

- Cholera

3,375 6,500 0.3

Aspergillius glaucus

44,000

88,000

3.4

Mucor racemosus B

17,000

35,200

1.4

Penicillium roqueforti

13,000

26,400

1.0

Protozoa

90% (1 log reduction)

99% (2 log reduction)

99% Kill Times

(

in minutes)

Paramecium

11,000

20,000

0.8

Infectious Hepatitis

5,800 8,000 0.3

Tobacco mosaic

240,000

440,000

17.1

Common yeast cake

6,000 13,200

0.5

Saccharomyces spores

8,000 17,600

0.7

Table 1: UV-C dosage and SteriZAP® UV-C Room Sterilizer Stainless Steel Kill Times

Organism Ultraviolet radiation (dose) in µWs/cm2 needed for kill factor: SteriZAP UV-C Room Sterilizer

Bacteria 90% (1 log reduction) 99% (2 log reduction) 99% Kill Times at 12 inches (in minutes)

Bacillus anthracis spores - Anthrax spores 24,320 46,200 1.8

Bacillus paratyphusus 3,200 6,100 0.2

Clostridium tetani 13,000 22,000 0.9

Ebertelia typhosa 2,140 4,100 0.2
Escherichia coli 3,000 6,600 0.3

Microccocus candidus 6,050 12,300 0.5
Microccocus sphaeroides 1,000 15,400 0.6

Neisseria catarrhalis 4,400 8,500 0.3
Phytomonas tumefaciens 4,400 8,000 0.3

Pseudomonas aeruginosa 5,500 10,500 0.4
Pseudomonas fluorescens 3,500 6,600 0.3

Salmonela paratyphi - Enteric fever 3,200 6,100 0.2
Salmonella typhosa - Typhoid fever 2,150 4,100 0.2

Stainless Steel

Sarcina lutea 19,700 26,400 1.0
Serratia marcescens 2,420 6,160 0.2

Shigella flexneri - Dysentery 1,700 3,400 0.1
Shigella paradysenteriae 1,680 3,400 0.1

Staphylococcus albus 1,840 5,720 0.2
Staphylococcus aureus MRSA 2,600 6,600 0.3

Staphylococcus lactis 6,150 8,800 0.3
Streptococcus viridans 2,000 3,800 0.1

Molds 90% (1 log reduction) 99% (2 log reduction) 99% Kill Times (in minutes)
Aspergillius flavus 60,000 99,000 3.9

Aspergillius niger 132,000 330,000 12.9
Mucor racemosus A 17,000 35,200 1.4

Oospora lactis 5,000 11,000 0.4
Penicillium expansum 13,000 22,000 0.9

Penicillium digitatum 44,000 88,000 3.4
Rhisopus nigricans 111,000 220,000 8.6

Chlorella Vulgaris 13,000 22,000 0.9
Nematode Eggs 45,000 92,000 3.6

Virus 90% (1 log reduction) 99% (2 log reduction) 99% Kill Times (in minutes)
Bacteriopfage - E. Coli 2,600 6,600 0.3

Influenza 3,400 6,600 0.3
Poliovirus - Poliomyelitis 3,150 6,600 0.3

Yeast 90% (1 log reduction) 99% (2 log reduction) 99% Kill Times (in minutes)
Brewers yeast 3,300 6,600 0.3

Saccharomyces carevisiae 6,000 13,200 0.5
Saccharomyces ellipsoideus 6,000 13,200 0.5

VKM201228 Genlantis Page 4 of 5

6044 Cornerstone Court West, Bldg. E. San Diego, CA 92121  Toll Free [phone]  U.S. & Canada [phone]  www.genlantis.com

2020 Genlantis and Gene Therapy Systems, Inc.

UV sterilization in progress

Do NOT open door or enter area until this sign is removed

Name:_________________________________________

Date:__________________________________________

Time Sterilization Cycle Started:____________

Expected Cycle Completion:_________________

Photocopy this page of the manual and post on entrances/exits of areas that are being UV sterilized.