Gen IV Technology 8 CH STAND-ALONE DVMR User Manual

Download

User Manual

Thank you for purchasing our product. Please read this User

s Manual before

using the product.

STAND-ALONE DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 Channel Digital Video Multiplex Recorder

VER 2.0

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 CH STAND-ALONE DVMR

The most stable and reliable real stand-al one Digit al Video Multiplex Recorder

ALL ABOUT IMAGE RECOGNITION & PROCESSING

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC

SHOCK. DO NOT OPEN!

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This label ma y appear on the bottom of the unit due to space limitations.

The lightning flash with an arrowhead sy mbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “ dangerous voltage” within the product’s enclosure tha t ma y be of sufficient mag nitude to consti tute a risk of electr i c shock to persons.

The exclamation point wit hin an equilateral triangle is intended to alert the user to presence of important operating and maintenance (Servicing) instructions in the literatur e accompanying the appliance.

WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.

Attention: installation should be per formed by qualified servi ce Personnel only in accordance with the Nation al Electrical Code or applicable local codes.

Power Disconnect. Units with or without ON-OFF switches have power supplied to the unit whene ver the power cord is inserted into the power source ; however, the unit is operational only when the ON-OFF switch is in the ON position. The power cord is the main power disconnect for all unites.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSINGALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

A CLASS A computing device subject to certification by the Commission s hall be identif ied pursuant to par.2.925 et Seq of the chapter. In addition, the labe l shall include the following statement:

Where a device is constructed in two or more se ctions connec ted by wires and marketed toge ther, the statement specified in this Section is required to be affixed only to the main control unit.

The users manual or instruction manual for the EUT shall contain the following statement or eqivalent.

Caution : Changes or Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

If the EUT requires accessories such as special shielded cables and/or connectors to enable compliance with emission limits, the instruction manual for the EUT shall include appropriate instructions on the first page of the text concerned with the installation of the device that thes e special accessories must be used with the device. It is the responsibility of the user to use the needed special accessori es supplied with the equipment.

For a CLASS A digital device or peripheral, the instructions furnished the user shall include the following or similar statement placed in a prominent location in the text of the manual.

Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device, pursuant to Part 15 of FCC Rules. These limits are design ed to provide r easonable protection against harmful interference wh en the equipment is operated in a commercial environment. This equipme nt generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruct ion manual, may cause harmful interference to radio communications. Oper ation of the t his equipment i n a residential area is likely to cause har mful interfe rence in which case the user wi ll be require d to correct the interference at his own expense.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

Chapter 1 . Product package

Chapter 2. Installati on proc e dur e

1-1. The contents of package 3 1-2. Name and function of ea ch but ton (front panel ) 4 1-3. Name and function of each button (rear pane l) 5

2-1. Camera connection 6 2-2. Monitor connection (Composite monitor) 6 2-3. Monitor connection (S-VHS) 7 2-4. VCR & VIDEO PRINTER connection 7 2-5. Sensor connection 8 2-6. Network connection 8 2-7. HDD connection 9 2-8. Power connection 9

Chapter 3. Operation

3-1. DVR SYSTEM Log-in 10 3-2. Recording 11 3-3. Playback 14 3-4. Set-up 16

1. Basic operation 16

2. CAMERA SETUP 16

3. DISPLAY SETUP 17

4. TIME/DATE SETUP 19

5. RECORD SETUP 19

6. HDD MANAGEMENT 21

7. MISCELLANEOUS SETUP 21

8. TCP/IP SETUP 24

Chapter 4. Specification and Configuration

4-1. SPECIFICATIONS

4-2. Configuration Stand-alone DVMR 28 4-3. RS-232C Hex-code table 28 4-4. Arrange of RS 485 and RS-232C pin 29

9. FACTORY DEFAULT 26

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

Table of Contents

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

Chapter 5. Menual for Remote Viewer Software(TCP/IP) 30

Before reading this document

1. This document is intended for both the administrator and users of stand alone DVMR.

2. This manual contains information for configuring, managing and using stand alone DVMR properly.

3. To prevent fire or electrical shock, do not expose the product to heat or moisture.

4. Be sure to read this manual before using stand alone DVMR Model, even before installing HDD.

8. For questions and technical assistance of this product, contact your local dealer.

About this document

Before installing stand alone DVMR, be sure to thoroughly review and follow the instructions in this

User’s Manual. Pay particular attention to the parts those are marked NOTICE.

Also, when connecting with external ap plication, first turn the power OFF and follow

THE instruct ion in manual for appropriate installati on.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

5. Check electricity at the place you want to install the DVMR unit is stable and meets our electricity r equirements. Unstable electricity will cause malfunction of the unit or give critical damage to the unit.

6. Several chi ps on the main board of the DVMR unit and hard disk drive inside t he unit generate heat, and it must be properly discharged. Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close up an opening (fresh air in-take) on the right side of the unit..

7. Put the DVMR unit at well-ventilated place and do not put heat-generating objects on the unit. When it is installed inside 19 inch mounting rack together with other devices, please check built in ventilation fan of the rack is properly running.

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

Maximum playback speed of DVM R is 60x.

10 : Command button.

We have 3 different buttons, that are, save, print, and event, and those buttons work only when stop button is pressed.

a)Save

During searching r ecorded picture s, you can save pic tures one by one in the folder in client PC by pressing save button. Press Save button while you see recorded picture, and picture you selected by pressing Save button shall be save on the folder you alr eady assigned under the file name of year-monthday-hour-minute-second in jpg format.

b)Print

During searching recorded pictures, you can print picture, one by one, you see, by pressing Print butt on.

c)Event

Press event button to see alarm list saved in DVMR unit, and you can search recorded pictures based on event list by clicking any one of list.

11 : Calendar.

You can select date and time to search pictures recorded at selected time and date. You can refer to start and end of recording in 7.

Notice : From time to time, connection shall be cut unexpectedly due to conditions of network line.

Whenever it is cut, quit search w indow by pressing power switch( 1), and then press co nnec t but ton in l iveview window and scan button to enter into search window again, to conti nue searching.

Notice : Compatibility of Remote Viewer Software with different kinds of operating systems and PC

hardware m ay no t be sim ply s peci fied d ue to t he c harac te risti cs of net work that it is much relat ed wi th n ot only PC hardware and operating system but also other software installed on the client PC and conditions of network(internet) line. Basically, Remote Viewer Software is compatible with typical Windows operating system from Wind ows 98 to Windows XP.

Notice : To see continuous live view, we recommend not to select motion recording in RECORD SETUP

menu of DVMR. If it is set at motion recording in SETUP menu of DVMR, image transmission is done only there is motions detected.

Notice : While you search recorded data using client software in client PC, DVMR unit to which you access

via IP network is in playback mode, and no reco rding is done as far as you search recorded data. However, while you ar e in co nnection with DVMR un it v ia IP netwo rk for live vi ew , D VM R u nit continue s to record but at a little lowered recording rate. Therefore we recommend you to access to DVMR unit only when it is nec e s sary.

Speed of playback in DVMR unit according to scan rate set in 4-7-b).

Scan rate set in 4-7-b)

1x 2x 4x

8x 16x 32x 64x

1x 1x 1x 1x 1x 1x 1x

1x 2x 4x

8x 16x 30x 60x

Chapter 1 . Product Package

1-1. The contents of package

1. 8 ch stand-alone DVMR unit

ALL ABOUT IMAGE RECOGNITION & PROCESSING

Stand-alone DVR

8 channel

Stand-alone DVR

Describe how to install and operate this D VMR unit.

4. DC power adap ter and power cab le

Convert AC 110V or AC 220V into DC 12V to supply to DVMR unit.

3. Remote controller

IR remote controller enables an user to operate DVMR unit apart from th e unit.

2. User’s manual for 8 ch DVMR

POWER

5. Search recorded pictures via IP network

Function of each button in search window :

1: Power switch. Press power switch to quit. 2: Full screen button. Press full screen button to search recorded picture channel by channel in fu ll screen. 3: Quad button. Press Q uad button to se arch recorded pictures in qu ad screen, 4 pict ures from 4 channels at the

same time. 4: Screen division button : If press “+” button, it screen division is changed from 4 to 9 or from 9 to 16. “-“ button reduce screen division.

5: Time of recording. It in dicates when the pictures you see recorded. 6: Channel selection button. Press any one from 1 to 4 to see picture of corresponding channel, if you first chose full screen button( 2). 7: Time selection button. You can set time to search by dragging yellow mover to the left or right. See time displayed

in green color and find an exact time from which you search. 8: Start and end of recording. It shows time from which recording started and recording ended. Further it show time from which search will start. 9: Search operation button. You can search recorded data using various buttons useful for searching effectively as follows.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

Product package

Play fast backward (Speed set in SYSTEM SETTING) Move to start of recording (Press stop button first before this butto n) Play Backward(x1) Move to previous hour(on the hour). Press stop button first before this button. Stop Play forward(x1)

Move to next hour(on the hour) Play fast forward(Speed set in SYSTEM setting) Move to end of recording(Press stop button first before this button)

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

OVERWRITE RECORD PLAY SETUP

ZOOM

MODE

P/T

PIP FRZ

SEQPLAY

1 2 3 4

ENTER

5678

DIGITAL VIDEO RECORDER

USER PANTILT COMMAND

- It is to input protocols for specific PTZ camera you will connect to 16 ch DVMR unit, to control PTZ camera while you see live pict ures in the client program.

-You can save protocols of specific PTZ camera in the form of computer file(text file). Prepare text file of protocol for PTZ camera and save it on your PC. In the User Pantile Command window, press [Menu] button and again press [Load User P T File]. Then y ou can assign text file of protocol for PTZ camera you prepared in advance. It is very convenient function.

-If you want to control PTZ camera using button s on the front of 16 ch DVMR unit, you must input th e same protocol into DVMR unit in PAN/TILE CMD SETUP.

b) Scan. : Press scan button to enter into search window. Using various operation buttons, you can search recorde d pictures, s ave selected pictures on client PC, or print picture s. Refer to fo llowing paragraph “3. Search recorded pictures over IP network” for details

8) PTZ cont rol. Yo u can co ntrol Zoom, Focus , and Pa n/Til t of came ra whil e you se e liv e pictur es vi a IP net work. O f course, you must first input PTZ protocol for a specific PTZ camera you connected to your DVMR unit, into your DVMR unit. You can control PTZ camera with vari ous of commands in USER PANTILE COMMAND window above.

When you press corresponding buttons for Pan/Tilt control, press a couple of second every time you press to take care of data tr a ns m is si on speed thro ugh IP netwo rk. Otherwise, there is a possibilit y th at given proto c ol is transmi tted repeatedly, regardless of your intention.

Notice : From time to time, connection shall be cut unexpectedly due to conditions of network line, and you will see

disconnect button(

) is activated. Just press connect button( ) again, and you can continue to see live pictures.

1. POWER SWITCH WITH LED : DC power switch with LED

Generally speaking, cutting power to system may cause trouble in DVMR system or damage to HDD when HDD is in writing process, and we ask you to press [MENU] button first to protect HDD from being damaged or system failure before you press DC power switch off in practical operation.

2. MENU : Used to check or change parameters settings in SYSTEM SETUP. After pressing [MENU] button, input password and press [ENTER] button to enter into SYSTEM SETUP.

3. PLAY/ENTER : Starts playback, and in some functions, it is used as the SELECT key. Press shortly and it starts playback. If you press this button for a long time, you enter into GO TO menu to start playback from image you want to start.

4. MODE : Changes screen division. Whenever you press [MODE] button, screen division is changed from full screen to 4-split screen, 9-split screen in sequence, both in live or playback mode. To change channel in full screen mode, just press number button. If you press [MODE] button for a lone time, it changes type of monitor connected to DVMR unit form COMPOSITE to VGA, or from VGA to COMPOSITE, in case VGA option is included in DVMR system.

5. P/T : Manages PAN/TILT CONTROLLER. To control PTZ camera connected to DVMR unit, you have to select model of PTZ camera in PAN TILE CMD SETUP/MISCELLANEOUS SETUP.

6. 1/5,2/6,3/7,4/8 : Chooses each indicated camera in full screen mode. Each button is double number button, and pressing [1], [2], [3], and [4] for a very short time is for 1, 2, 3, and 4 respectively, and pressing [1], [2], [3], and [4] for a long time is for 5, 6, 7, and 8 respectively.

7. PIP : Assigns PIP (Picture In Picture)

8. FRZ : : Displayed screen is paused.

9. SEQ : To see display scre en in rotation fr om channel number 1, 2, 3, and so on, both in live and playback

mode. It also change Quad sc reen from 1/2/3/4 to 5/6/7/8.

1098765

1211

10. ZOOM : Enlarges the display screen by 200%. Digital zooming.

11. Remote Controller Sensor Input Window

12. Direction button : [LEFT], [RIGHT], [UP] and [DOWN].

In playback mode, [LEFT] and [RIGHT] buttons are for selecting playback direction(forward/backward), and [UP] and [DOWN] buttons are for increasing or decreasing speed of playback.

NOTICE : If the Input window (IR receiver) is covered, the remote controller may not work. NOTICE : If several buttons are simultaneously or incorrectly pressed, the system may not be operated unproperly.

POWER

ALL ABOUT IMAGE RECOGNITION & PROCESSING

13. LED Lamps : Represent status of operation. OVERWRITE/RECORD/PLAYBACK/SETUP.

8 channel stand-alone DVMR

1. Unit Description

1-2. Name and function each button (front panel)

OVERWRITE RECORD PLAY SETUP

14. CD-RW DRIVE

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

MENU PLAY

MODE

P/T

PIP

FRZ

SEQ

ZOOM

ENTER

567 8

5. LOOP Output

6. VCR Connection

7. MONITOR Connection

8. VGA Connection

10. D/C Power Connection

3. LAN (TCP/IP)

2. Sensor Input/Output

1. RS-232C and RS-485 port C onnection

4. Camera Connection

9. S-VHS Connection

NOTICE : When connecting with other applications, be sure to turn off the system.

678

9 10

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

1. Unit Description

1-3. Name and function each button (Rear panel)

7) : Set button. 2 different set buttons a) Setting : Press this button to input IP Address(or select a unit of 16 ch DVMR unit among many) and

others and to set circular monitoring interval and scan rate, to assign folder where you want to save pictures you will select during search, to input protocol for PTZ cameras or select any model of PTZ came ras amo ng ma ny m odel s whos e pr otoc ols you al rea dy in put, as fol lo wing dialog box.

CONNECTION

-On the Name box, you are requested to input name of 16 ch DVMR units, in case you want to access to any one

DVMR unit among more than a unit. You can save IP information in Configurations Window and s elect name of DVMR unit to which you want t o access.

-Input IP Address you already input into DVMR unit(TCP/IP SETUP) in IP ADDRESS.

-Input Port number you alre ady input into DVMR unit in PORT. Just input 8000, which is default port number.

In some cases, port number 8000 is blocked by firewall, and you have to input different number like 8090 which is not blocked.

-Input “admin” in ID.

-Input the same password you set into DVMR unit in PASSWORD. Default password of 16 ch DVMR unit is

blank(null). You are reque sted to enter y our own password using number keys from 1 to 16 on front panel of 16 ch DVMR unit

OPTION

-Select circular monitoring interval ranging from 0.1 sec to 10 sec. The smalle r it is, the faster picture of each

channel rotates. The absolute circulation interval is a little different from set value depending on data transfer rate of IP network.

-Select scan rate ranging from 1x to 64x. The larger it is, the faster search speed is. The absolute search speed is a

little different from set value depending on data transfer rate of IP network.

-Reconnection count : In case disconnected due to some reason, client program tries to reconnect after this time.

SAVE OPTION

It is to assign fo lder on which you want to save pictures you will select while you search recorded pictures, picture by picture.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

DC 12V

VCR

CH1 CH2 CH3 CH4

MONITOR

LOOP

V G A

ALARM/ RELAY

CH5 CH6 CH7 CH8

ETHERNET

Comm Port

RS-232C/485

S-VHS

CAUTION

RISK OF ELECTRIC

SHOCK. DO NOT OP EN!

CAUTION : TO REDUCE THE RISK OF ELECTRICAL S HOCK, DO NOT OPEN COVERS. NO U SER SERVICEA BLE PARTS IN SIDE. REFER SERVICING TO QUALIFIED SERV ICE PERSONNE L.

WARNNIG : TO PREVENT FIAE OR SHOCK HAZ ARD, DO NOT EXPOSE UNITS NOT SP ECIFICALLY DE SIGNED FOR O UTDOOR USE T O RAIN OR M OISTURE

Now, hit the "Release" button and then hit "Renew". If all goes well, you'll get ne w information, and it is for your DVMR unit. Write down this information on separate paper and input IP Address, Subnet Mask, and Default Gateway into your DVMR to which you want to access via IP network. ⒞ Confirm if IP Address is working by executing pingtest

Execute pingtest with IP Address which you assigned to DVMR unit, check if it is successful before you try to access to DVMR unit via IP network. If it is not successful, you may not be able to access to DVMR unit via IP network, and we recommend you to get help fr om your network a dministrator.

4. Live view via IP network

Click Remote Viewer icon to view live pictures via IP network. You will see then following window.

Function of each button in live-view window :

1) : Power switch. Press power switch to quit. Befo re press power switch button, press disconnect button first .

2) : Connect butto n. P res s co nnect button to c o nnect to DVMR un it via IP netw ork to see live pic t ure s of DV M R u nit.

You will see th e s am e live pictur es , w h ic h a r e d is pl ay ed on monito r of D VMR unit with a c ertain time de la y depending on transfer rate of IP network.

3) : Disconnect button. Press disconnect button to cut connection to DVMR unit via IP network.

4) : Screen division button. You can select to see pictures of any single channel, 4, 9, and 16 channels at the same

time. You can select channel number from 1 to 16 to see pictures of selected channel. If you selected 4, you swill see channel number from 1 to 4 are all activated.

5) : Channel number button. You can select channel number to see live pictures from selected channel.

6) : Status window. It shows Date and Time. Further it displays “Connection established” and a circular fan on the left

bottom is rotating when connection butt on is activated, or “Waiting for connection” w hen disconnection button is activated.

2-1. Camera Connection

Connect the camera to the CAMERA INPUT on the Rear Panel of the system.

2-2. Monitor Connection (Composite Connection Method)

Connect the monitor to the MONITOR OUT on the Rear Panel of the system

VIDEO

LENS

VIDEO

AC24V/DC12

V.P

LEVEL

Rear part of CAMERA

VIDEO A

IN OUT

VIDEO C

IN OU T

VIDEO B

IN OUT

ALL ABOUT IMAGE RECOGNITION & PROCESSING

Notice : Connect camera or monitor to DVMR unit while DC power switch on the front panel is off.

Screen positioning : If picture displayed in your monitor is not at the center of monitor, you can relocate images to make them shown in the middle of monitor. Press [P/T] button for a long time to enter into screen position mode, and you can adjust location of pictures using [UP], [DOWN], [LEFT] and [RIGHT] buttons. Press [P/T] button for a long time again to quit screen positioning mode. If you press [ENTER] button in the process of screen positioning mode, location of pictures return to original location set by manufacturer.

VCR

CH1 …... CH8

MONITOR

LOOP

V G A

8 channel stand-alone DVMR

2. Installation

Chapter 2. Procedure

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

VCRCH1

…...

CH8

MONITOR

LOOP

V G A

VCRCH1

…...

CH8

MONITOR

LOOP

V G A

VCR

CH1 …... CH8

MONITOR

LOOP

V G A

2-3. Monitor (S-VHS) Connection

Connect S-VIDEO Monitor to MONITOR OUT(S-VHS) on the Rear Panel of the system.

2-4. VCR & VIDEO PRINTER Connection

Connect VCR or VIDEO PRINTER to VCR OUT on the Rear Panel of the system.

VIDEO

IN OUT

VIDEO

IN OUT

VIDEO

IN OUT

ALL ABOUT IMAGE RECOGNITION & PROCESSING

VIDEO PRINTER

VCR

8 channel stand-alone DVMR

2. Installation

3. How to get IP for DVMR unit

There is 2 different ways to input IP address and other data into DVMR unit. The first way is to make DVMR system get IP address from DHCP server automatically. It is only possible in case DVMR unit is co nnect ed to c abl e mod em(dy namic IP), Intra net un der DH CP s erver or IP s har er whi ch support DHCP. Select “DHCP” in TCP/IP setup to get IP address automatically. The second way is you get IP address and other data before you connect DVMR unit to network and later input this IP ad dress an d othe r data in to DVMR unit. Ex cept the ca se yo u already know IP addres s assig ned for DVMR unit, get IP address for DVMR unit as following process in the client PC from which you want to access to DVMR unit via IP network. If you connect DVMR unit to leased line with static IP already known, it is not necessary to follow following process to get IP information.

a) “ipconfi g” or “w in ip cfg”

Execute “ipc on fi g” co m m an d in the client PC wi th Wi ndows 2000 and W in do w s XP , an d “ winipcfg” com m an d in the client PC with Windows 98 and ME, and you will get IP informations, that are IP Address, Gateway, Subnet Mask. Write down those numbers and input into DVMR unit to which you are going to access via IP network. As far as DVMR is in operation without turning off, it is considered that this IP Address is assigned just to this DVMR unit. Then, restart the client PC to get different dynamic IP address for client PC after you get IP information for DVMR unit. Derail procedure to get IP information in different Windows is as follows. ⓐ Window 2000 First you need to get to the command prompt using the command shell. The best way is from the run menu. Start--> Run --> and type in Command. Then either hit enter or click OK. At the command prompt, type in ipconfig. This will pull up the information that you need to find IP Address for DVMR unit. ⓑ Windows XP

If you want to get IP A dd res s for your D VMR in Wi ndow s XP , yo u ca n ru n ipconfig in one easy step. Open Run and type "cmd /k ipconfig" without the quotes. This will open the command prompt and start ipconfig the easy way. Assign IP Address you get to DVMR unit.

When winipcfg launches, you'll get a window like this one:

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

31 8

2-5. Sensor Connection

2-6. Network Connection

RS-232C : Connection to PC to operate DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

RS 485 : Connection to PTZ camera RJ-45 (ETHERNET) : Connection to LAN, WAN or Internet

You can connect dry-contact type sensors. In case of sensors with TTL output (5 Volts system) , GND of sensor must be connected to GN D of DVMR unit and signal line to alarm input from D1 to D16 as shown in following figure.

Short-circuit between any of D1 from D16 and GND is recog nized as an alarm.

Relay output is output in case there is an alar m input, and is connected to external device us ing COM-NO (Normal Open) or COM-NC (Normal Clos e) contact.

10 9876543211

25 24 23 22 21 20 19 18 17 16 15 14

13 12

D1D2D3D4D5D6D7D8GNDGNDCOMNONC

GNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGND

RELAY Output

All GNDs are connected to each other on circuit.

ALARM INPUT

For more details, refer to arrangements RS-232c pins in page 29.

ALARM/ RELAY

ETHERNET

Comm Port

RS-232C/485

V G A

PTZ

CAMERA

VGA : Connection to PC monitor

8 channel stand-alone DVMR

2. Installation

SENSOR

14(GND)

15(GND)

16(GND)

17(GND)

18(GND)

19(GND)

20(GND)

21(GND)

c) ADSL(ADLS modem with PPPoE protocol) line with static IP or dynamic IP.

IP forwarding is what we have to set in web site of Router or Gateway to connect external Port to internal IP assigned by Router or Gateway.

d) In the same Intranet : Supports

- LAN under DHCP(Dynamic Host Configuration Protocol) Server

- LAN under IP share

LAN

network

DVM

Intern

Client PC

Intranet

Cable modem

ADSL

DHCP SETUP in TCP/IP SETUP: DHCP (DVMR syst em autom atically ge ts IP address)

PC Client program

ADSL Modem Router/Gateway DVMR-1

DVMR-2

DVMR-16

Example of IP Forwarding in website of Router or Gateway

192.168.1.165:80 15

192.168.1.151:80 01

192.168.1.150:80 00

211.100.16.8

Internet

ADSL Modem

with dynamic IP or static IP

PPPoE protocol

Router or

Gateway

DVMR

DHCP SETUP in DVMR unit

MANUAL

Client

Settings in website of Router or Gateway :

IP Forwarding(IP Bounding, Port Forwarding, Port Bounding, or Po rt

Routing)

LAN

network

DVM

Intern

Client PC

Intranet

Cable modem

ADSL

DHCP SETUP in TCP/IP SETU P: DHCP (DVMR system automatically gets IP address)

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

2-8. Power Connection

Detail setup in SYSTEM SETUP

For detail setup, refer to the instruction of SYSTEM SETUP.

Connect the power to the POWER CONNECTION on the Rear Panel of the system,

Turn on the POWER and Log-in to the system

Follow instruction in the Log-in part of this manual to input the PASSWORD and start the system.

and turn on the switch.

Factory default password for account manager and user, set by manufacturer, is null, therefore just press [ENTER] button in case DVMR system asks to input password, as far as you did not change pass w or d .

DC 12V

ALL ABOUT IMAGE RECOGNITION & PROCESSING

2-7. HDD connection

Connect main board and HDD using IDE HDD cable and power cable included in the package. If you install a unit of HDD, jumper setting of HDD must be on (DS) Master, as specified by HDD manufacturer. Fix HDD on the bottom of DVMR case using screws included in the package. Sc rews must be ins erted from outside of the bot tom. And CD-RW dri ve must be on Slave.

Notice : Formatting befo re installat ion is not required, because DVMR system automatically detects and formats HDD. In the first operation after installation of HDD, first set at FACTORY DEFAULT in setup menu of DVMR system and then do HDD CLEAR in HDD MANAGEMENT in setup menu of DVMR system.

Notice : To turn off DC power switch on the front panel of DVMR case, be sure to press [MENU] button first. If you press [MENU] button, DVMR system stops recording, and you can cut power to DVMR unit while HDD head is not in writing mode. It is necessary to press [MENU] button first and turn DC power switch off for protection of HDD head from being damaged and eliminate possibility of mal-function of DVMR unit.

Notice : In case you see “UNKNOWN HDD DETECTED” message is displayed after booting process, just clear HDD and set at FACTORY DEFAULT to make this HDD be detected by DVMR system.

8 channel stand-alone DVMR

2. Installation

Chapter5. Manual for Remote Viewer Software(TCP/IP)

General description : TCP/IP option enables users to view live pictures, search recorded pictures, or control PTZ camera via Internet line, far apart from the DVMR unit, and users can store selected recorded pictures on HDD of client PC. Our stand-alone DVMR does not adopted web browser method for access to DVMR unit via Internet line, and you must install Remote Viewer software included in the package on client PC before you try to access to DVMR unit over IP network.

1. TCP/IP SETUP in DVMR unit

Before you install Remote Viewer software, be sure to input IP address and others in TCP/IP SETUP of

DVMR unit. Then, execute SETUP.exe on Remote Viewer software CD included in the package of stand-alone DVMR with TCP/IP option.

Install client software(Remote viewer) to access to DVMR unit via Internet line.

To access to our DVMR unit via IP network, you have to connect DVMR unit to IP network as one of followings and assign IP address, Subnet mask, and Gateway to our DVMR unit. Our DVMR unit accepts static IP and it also work in case both DVMR unit and client PC are connected to the same Intranet (LAN). a) Static IP : If DVMR unit is connected to leased line with static IP, we can access to DVMR unit via

Internet line far a par t fr om D VM R u nit. ( DH C P SET UP i n T C P/IP SET UP : MANUAL(Input IP address ma nu al ly )

2. Conditions of IP networ k

b) Cable modem with dynamic IP : If DVMR unit is connected to cable modem with dynamic IP, we can

access to DVMR unit via Internet line far apart from DVMR unit.

Internet

DVMR

Client PC

Cable

modem

with

dynamic IP

DHCP SETUP in DVMR unit

DHCP (DVMR system automatically gets IP address)

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

5.Menual for Remote Viewer Software(TCP/IP)

PTZ

HDD

(MASTER)

POWER

OVERWRITE RECORD PLAY SETUP

ZOOM

MODE

P/T

PIP FRZ

SEQPLAYMENU

1 2 3 4

ENTER

MARK SPEED

CD-RW

56 78

ALL ABOUT IMAGE RECOGNITION & PROCESSING

4-4. Arrangement RS-232C and RS-485 pin

# 2 RxD

# 3 TxD

# 5 GND

TxD # 3

GND # 5

RxD # 2

DVMR unit Other device (PC)

D-SUB 9 cable (twisted RS-232C cable)

Comm Port

RS-232C

1 5

6 9

Pin No. Definition

1 NC 2 RxD 3 TxD 4 SD-(RS 485) 5 GND 6 SD+(RS 485) 7 NC 8 NC 9 NC

Connection to PC using RS-232C cable

8 channel stand-alone DVMR

4. Configuration

3) When you get the DVMR, you can enter into Setup menu by just pressing [ENTER] button.

1) Press [MENU] button to enter the system menu after starting the system.

2) DVMR system asks you to ente r pas sw o rd to verify authority of user as shown on the left.

Factory default password is [ENTER]

NOTICE : We recommend you to enter your own password as per procedure in PASSWORD SETUP/MISCELLANEOUS SETUP of setup menu.

6) After entering to setup menu, press [MENU] button to go back to the system menu. If password entered matches previously set password, “PASSWORD OK” message appears and you

can enter into SYSTEM SETUP. If password entered does not match previously set password, DVMR system just go back to initial mode,

that is, showing live pictures and recording as set before.

ENTER PASSWOR D : _______ _

INPUT YOUR OWN PASSWORD, THEN PRESS [EN TE R]

TO EXIT, PRES S [ME NU ]

Enter the password

default P/W : [ENTER]

Input or modify

NOTICE : Be sure to memori ze the changed password.

In case you forgot password, you can not enter into SYSTEM SETUP and can not change parameters of DVMR operation, and just leave DVMR unit to run as settings you done before. In case you forgot own password and want to enter into SYSTEM SETUP, please contact dealer to get instruction for entering into SYSTEM SETUP for password change.

4) In case you already have changed the password, enter your own password.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8 channel stand-alone DVMR

3. Operation

3-1. DVMR SYSTEM log-in

Chapter 3. Operation

5) Press [ENTER] button after you enter password, to enter into SETUP menu.

Indicat es operatin g status : Recording : Standby for recording : Backward/Forward : Fast backward/forward

2. MODE

Changes screen division in the sequence of full screen of specific channel, 4-split screen, and 9split screen whenever pressed.

If it is pressed for a long time, it changes type of monitor from COMPOSITE to VGA or VGA to COMPOSITE in case VGA option boar d is included in the DVMR package. In case you connect CRT type PC monitor to DVMR unit, and monitor type is set at COMPOSITE, pictures displayed shall be flickering.

3. P/T

1. PLAY

Changes to Playback Mode from Recording. If pressed shortly, playback starts from the stop point in previous operation. If pressed for a long time, you can enter into GO TO MENU and select by PERCENT, TIME/DATE, or EVENT LIST the point from which you want to replay.

Refer to Playback part(PAG E.13)of this manual for details.

CH-01

Recording Mode

ALL ABOUT IMAGE RECOGNITION & PROCESSING

CH-02 CH-03

CH-04 CH-05 CH-06

CH-07 CH-08

03 / 10 / 25 16 : 11 : 38 TIM R 12.34% P 5.03%

Indicat es statu s of recoding and playback TIM : Cont inuous recording MOT : Motion recording ALM : Alarm recording R : Indicates how many % of total HDD space is recorded. P : Indicates what is starting point of next playback, unless you skip to specific point in GO TO MENU.

After pressing [P/T] button, command with channel number(from 1 to 8) in front is displayed whenever you press [LEFT] or [RIGHT] button. Select channel number first by pressing [UP] or [DOWN] butt o n, and select comman d by pr es s in g [LEFT] or [RIGHT] button. Then, PTZ camera will move as per c ommand you selected as far as you press [ENTE R] button.

In case you connected PTZ camera t o any channel of DVMR unit, press [P/T] button first to control th is camera using operation but tons on the front panel. Be sure to select model of PTZ camera whose protocol is already incorporated into DVMR system. Model of PTZ camera whose protocol incorporated is PELCO D type, DRX-502A. For PTZ camera w hose protocol is not built-in protocol, you have to input protocol of that camera in USER DEFINE /PAN/TILT CMD SEPUP/MISCELLANEOUS SETUP.

Press [P/T] button once more to stop PTZ camera control.

Indicates camera title. Default title is CH-1, CH-2, … CH-8. You can change camera tile in EDIT CAMERA TITLE in CAMERA SETUP.

Indicates date and current time.

YY / MM / DD

Hr/Min/Sec

PAN/TILT Control

(Ex: PELCO D type)

CH-01

CH-02 CH-03

CH-04 CH-05 CH-06

CH-07 CH-08

03 / 10 / 25 16 : 11 : 38 TIM R 12.34% P 5.03%

P / T

1. PAN RIGHT

1. Indicates address of camera (channel number from 1 to 8)

Change by pressing [UP] or

[DOWN] button

Select command by pressing [LEFT] and [RIGHT] button

POWER ON POWER OFF PAN LEFT PAN RIGHT TILT UP TILT DOWN P/T LEFT-UP P/T RIGHT-UP P/T RIGHT-DOWN P/T LEFT-DOWN ZOOM IN ZOOM OUT FOCUS FAR FOCUS NEAR FOCUS AUTO IRIS OPEN IRIS CLOSE IRIS AUTO AUTO SCAN GO TO PRESET SET PRESET CLEAR PRESET PAN/TILE STOP

8 channel stand-alone DVMR

3. OPeration

3-2. Recording

ALL ABOUT IMAGE RECOGNITION & PROCESSING

4-2. Configuration

4-3. RS-232C Hex-codes table

1 Byte ASCII-code

8 channel stand-alone DVMR

4. Configuration

Camera #1~8

MODE

FRZ

SEQ

ZOOM

‘D’

‘F’

‘Q’

‘Z’

PIP

P/T

ENTER

‘I’

‘T’

CH1

CH2

CH3

CH4

‘1’

‘2’

‘3’

‘4’

CH5

CH6

CH7

CH8

‘5’

‘6’

‘7’

‘8’

LEFT

RIGHT

‘U’

‘M’

Sensor Alarm

Remote

Controller

TCP

/IP

TCP/IP

RS-232C Printer

P/T Camera RX Box

VCR TV Monitor S-Video Monitor

Video

Printer

ALL ABOUT IMAGE RECOGNITION & PROCESSING

4-1. SPECIFICATIONS

INPUT

OUTPUT

S/N RATIO

HORIZONTAL RESOLUTION

COLOR

ZOOM

PIP

SEQUENCE

SCREEN QUALITY

SPEED

MATERIAL

COMPRESSED PICTURE

PICTURE RECORDING

METHOD REC, MODE TRACK PLAY

SPLIT SCREEN

WEB INTERFACE

POST ALARM FUNCTION

BACK-UP OTHERS

CAMERA CONTROL

HDD

CD-RW BACK-UP

8 CH INPUT 1.0 VP-P, 75 OHM UNBALANCED (BNC TYPE) 3 OUTPUT VBS : 1.0VP~P.75 OHM UNBALANCED (BNC TYPE)

MORE THAN 4dB

480TV LINES

16.7 MILLION

LIVE & PB AVAILABLE AVAILABLE AVAILABLE FULL : 720(H)X480(V) ACTIVE PIXELS

1/4 SCREEN : 360(H)X240(V) ACTIVE PIXELS

0.1~30 FRAME/SEC (EACH CHANNEL) HDD JPEG

FIELD SWITCHER METHOD FULL SCREEN RECORDING REAL-TIME/ TIME-LAPSE / EVENT

SEARCH, STILL

FULL, QUAD DISPLAY. 9-SPLIT

Stand alone DVMR

TCP/IP with client software 1~59SEC, CONTINUOUS TIMING ESTABLISHMENT POSSIBILITY

CONVENTIONAL VCR, TIME LAPS VCR (VCR OUTPUT PROVIDED) REMOTE BACK-UP USING TCP/IP INTERNAL BACK-UP(MARK IMAGE)

RS232C, RS485, 8 ALARM INPUT PAN/TILT/ZOOM AND FOCUS

REMOTE CONTROL : EXTERNAL EQUIPMENT, WIPER,PUMP,FAN AND HEATER

INTERNAL 1 HDD

CD-RW DRIVE CD-R MEDIA

VIDEO I/F

MONITORING

METHOD

RECORDING

/PLAY

FUNCTION

OTHER

FUNCTION

MODEL NO

OPERATION TEMPERATURE

OPERATION HUMIDITY

IR REMOTE CONTROLLER

DIMENSION

WEIGHT

POWER SUPPLY

41F~ 104F (5C~ +40C) LESS THAN 90% BUILT-IN 19 INCHES IN WIDTH , 1.5U 434 mm x 360 mm x 66 mm APPROX. 4.8KGs (WITHOUT HDD) DC ADAPTER (12V DC 5A)

MECHANICAL

8 channel stand-alone DVMR

4. Configuration

Chapter 4 . Specification and configuration

4. PICTURE IN PICTURE (PIP)

1. When it is full screen display mode, press [PIP] button to see small size pictures rotating in sequence. To select channel for full screen, just press n umber button from [1/5], [2/6], [3/7], and [4/8]. Of course you have to press number button for longer time to select any of number 5 to 8.

Press [PIP] button once more to return to full screen mode you started.

NOTICE : PIP is available just in full screen mode.

To change the location of smaller screen, press [FRZ] button and use direction button to move to desired

5. FRZ

1. You can make pictures displayed freeze by pressing [FRZ] button in both live view and playback mode.

In live view, it is just working when it is in full screen mode, while it works whether it is in full screen mode or 4-split or 9 split mode, in playback mode.

PICTURE IN PICTURE

Freeze

location.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

CH-1

PIP

03 / 10 / 25 16 : 11 : 38 TIM R 12.34% P 5.03%

PIP rotates in sequence

3. You can set rotating time interval in TIMER SETUP/ MISCELLANEOUS SETUP in SETUP menu. In TIMER SETUP, you can set rotating time interval not only for PIP screen but also for FULL SCREEN and QUAD screen.

2. Press [SEQ] button to make fullscreen rotate just like PIP does, when it is in PIP mode.

2. To exit FRZ mode, just press [FRZ] button again.

3. If you press number button from 1 to 4 shortly or for longer time, FRZ mode is automatically released and image of channe l you pressed is displayed in full screen.

CH-01

CH-02 CH-03

CH-04 CH-05 CH-06

CH-07 CH-08

03 / 10 / 25 16 : 11 : 38

R 12.34% P 5.03%

Indicates [FRZ] button

is pressed.

8 channel stand-alone DVMR

3. Operation

6. SEQ

1.In live mode, full screen or 4-split screen rotate in sequence, whenever you press [SEQ] button shortly.

3. Sequence of rotation is 1, 2, 3, 4, 5, 6, 7, 8, 1, and so on, if [SEQ] button is pressed for more than a sec when number 1 channel is in full screen.

6.To exit from SEQ mode, just press [SEQ] button again.

4. If [SEQ] button is pressed for a long time when it is in 4-split mode, sequence of rotation is 1/2/3/4 and 5/6/7/8, and so one.

To change rotating time interval of full screen or 4-split screen in live view, set FULL SCREEN or QUAD SCREEN value again in TIMER SETUP/MISCELLANEOUS SETUP.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

7. ZOOM

CH-3 ZOOM

03 / 10 / 25 16 : 11 : 38 TIM R 12.34% P 5.03%

CH-5 ZOOM

03 / 10 / 25 16 : 11 : 38

R 12.34% P 5.03%

ZOOM in live view

ZOOM in playback

1.In full screen in live mode or in playback mode, press [ZOOM] button to see 2 times enlarged picture.

2. Vertical bar and horizontal bar on the bottom and on the right respectively show which are of pic ture is enlarged, and you can change area to be enlarged by pressing [LEFT], [RIGHT], [UP], and [DOWN] button.

3. Because it is enlarged 2 times digitally, picture quality is a little poor than picture you see in normal playback mode.

4. To exit ZOOM mode, just press [ZOOM] button again.

2. If you press [SEQ] button for a long time in live view, full screen or 4-split screen automatically rotate until you press [SEQ] button for a long time again.

5. In playback mode, [SEQ] button is used to move to next channel when it is in full screen mode. That is, it shows full screen of next channel whenever [SEQ] button is pressed shortly in pl ayback mode.

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

9. FACTORY DEFAULT

Press [ENTER] button when half-tone green bar is in on FACTORY DEFAULT.

FACTORY DEFAULT

ALL SETUP CAMERA C OLOR CAMERA TITL E MOTION MASK PAN/TIL E COMMAND SYSTEM S TATUS

RUN

HDD MANAGEMENT

1) CAMERA COLOR

SELECT , EDIT ENTER /

FACTORY DEFAULT is parameters setting done just before delivery by manufacturer, and manufacturer recommend our users to use DVMR unit with settings done by manufac turer until our users become to have full understanding about DVMR system.

FACTORY DEFAULT can be set group by group or as a whole at once .

Parameter settings about color of camera like brightness, contrast and oth ers of camera . If we set CA M ER A CO LO R at YES, all changes you made in ADJUST COLOR/ CAMERA SETUP shall be delete d and return to settings done by manufacturer befor e delivery.

2) CAMERA TITLE Default camera title is CH-01, CH-02, and so on.

3) MOTION MASK Motion mask is for motion detection area, motion window, and sensitivity.

If we set MOTION MASK at YES, all changes you made in MOTION SETUP/CAMERA SETUP shall be deleted and return to settings originally done by ma nufacturer.

4) PAN/TILT COMMAND As explained in PAN/TILT COM SETUP/MISCELLANUOUS SETUP, this DVMR system includes

built-in pr otocol models like PELCO D type and we can select model of PTZ camera connected to DVMR unit. In case PTZ came ra you are going to connect to DVMR unit is not one of models whose protocol is already incorporated into DVMR system, you can input protocol of PTZ camera in USER DEFINE mode/PAN TILT SMD SETUP menu.

Even though you set PAN/TILT COMMAND at YES, built-in protocol remain unchaged However, protocol you input in USER DEFINE model is deleted if you set PAN/TILT COMMAND at YES and set at FACTORY DEFAULT. Be careful not to set at YES to keep protocol you input as a USER DEFINE model.

5) SYSTEM STATUS It is setting related recording parameters like recording speed, IP address, and others related to system. If you set SYSTEM STATUS at YES and set at FACTORY DEFAULT, you have to set recording speed, and input IP address and others again.

6) ALL SETUP If you set ALL SETUP at YES and set at FACTORY DEFAULT, all groups of FACTORY DEFAULT are

initialized. That is, all parameter settings is done again just as done by manufacturer before deliverly.

--NO NO NO NO NO

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

3) Example of Port Forwarding

Because ADSL is the most popular Internet se rvice widely av ailable in most of countries, we explain more details about how to connect DVMR unit to ADSL line via Router or Gateway, to allow accessing to this DVMR unit via Internet line far apart from DVMR unit.

InternetPC

Client program

(remote viewer)

ADSL

modem

dynamic IP

static IP

DVMR unit-1

Router

Gateway

PPPoE

protocol

Port Forwarding (IP Forwarding)

DVMR unit-5

DVMR unit-4

DVMR unit-3

DVMR unit-2

Other

device(PC)

211.100.16.8

IP : 192.168.1. 150 PORT : 8000

IP : 192.168. 1.151 PORT : 8001

IP : 192.168. 1.152 PORT : 8002

IP : 192.168. 1.153 PORT : 8003

IP : 192.168. 1.154 PORT : 8004

IP : 192.168.1.165 PORT : 8015

Intranet

Port forwarding : Port forwarding is called differently by each of router manufacturers, like IP forwarding, IP bounding, port forwarding, port bounding or port routing. Our users can set port forwarding stated in installation manual of router or gateway without big trouble, and complete IP network to which user can connect many of our DVMRs, that are 1 ch DVMR, 4 ch DVMR, 8 ch DVMR and 16 ch DVMR, to access to those units via Internet line far apart from those units.

Port forwarding is a kind of arrangement we have to set in web site of Router or Gateway to connect external port to internal IP address, for example in above picture, PORT 8000 to IP 192.168.1.150, PORT 8001 to IP 192.168.1.151, an so on.

According to our own test with NETGEAR Router, it is workin g perfectly, and we recommend our users to adopt NETGEAR Router in case DVMR unit is connected to ADSL line.

PORT From 8000 To 8015

8 channel stand-alone DVMR

3. Operation

1. Playback setup

4) Display screen will appe ar as shown on the right picture.

2. How to set in GO TO MENU

ALL ABOUT IMAGE RECOGNITION & PROCESSING

CH-01

CH-02 CH-03

CH-04 CH-05 CH-06

CH-07 CH-08

03 / 10 / 25 16 : 11 : 38 TIM R 12.34% P 5.03%

GO TO MENU

1) Press [PLAY] button to enter into playback mode.

2) [PLAY] button is is pressed shortly, it just start playback from the previous stop point.

3) If you press [PLAY] button for longer time, you can enter into GO TO MENU, and set the point from which you want to start playback. You can set starting point of playback by setting PERCENT, TIME/DATE, or EVENT LIST in GO TO MENU.

[ GO TO MENU ]

PERCENT TIME/DATE EVENT LIST

1) First select any one of PERCENT, TIME/DATE, and EVENT LIST using [UP] and [DOWN] buttons. If you select PERCENT, you are supposed to set starting point of playback by percent. If you select TIME/DATE, you are supposed to set starting point of playback by time and date. If you select EVENT LIST, you will enter into event list and select one of event list to start playback from selected event.

2) PERCENT Press [ENTER] button when triangular cursor is in front of PERCENT to select target by percent. In [PERCENT GO TO] men u, start and end point of recording shall be displayed. At the same time, how many % of total HDD(1 or 2 units in DVMR unit) space is recorded is displayed. Under this line, you are requested to set starting point of playback by % using [LEFT] and [RIGHT] button and [UP] and [DOWN] button. After you set star ting point by %, press [ENTER] button shortly, and Target(starting point) is display in time/date and at the same time playback starts from the point you set, while all message is displayed. If it is the right point you want to start playback, then press [PLAY] button for longer time again to make messages disapp ea r . To stop playback and go back to recording mode, press [PLAY] button shortly again.

3) TIME/DATE Press [ENTER] button when triangular cursor is in front of TIME/DATE to select target by time/date. In [TIME/DATE GO TO] menu, start and end point of recording shall be displayed. Under this line, you are requested to set starting point of playback by time and date. Using [LEFT] and [RIGHT] button and [UP] and [DOWN] button, set time and date from which you want to start playback. Then press [PLAY] button shortly, and it starts to playback from the point you set, however all messages are still displayed. If it is the r ight point from which you want to start playback, press [ENTER] button for longer time once more, and messages shall be disappeared..

4) EVENT LIST Press [ENTER] button when triangular cursor is in front of EVENT LIST to select target by event list. In [EVENT-LIST GO TO] menu, list of event shall be displayed. Just select event from which you want to start playback using [DOWN] and [UP] bu ttons, and the n press [PLAY] button shortly to start playback. If it is the right point from which you want to start playback, press [ENTER] button once more to make all messages disappeared.

8 channel stand-alone DVMR

3. Operation

3-3. Playback

5) Playback Speed Setup

PLAYBACK Speed Setup

ALL ABOUT IMAGE RECOGNITION & PROCESSING

In playback mo de , yo u ca n ad just speed of play b ac k by pr es s in g [UP] or [DOWN] button easily. Just press [UP] button, and you can increas e playback spee d from 1x to 2x, 4x , 8x, 18x, 32x, or 64x step by step. In playback speed from 2x to 64x, DVMR system skips a certain numbers of pictures recorded in sequen ce as per playback speed selected for fast search.

To the contrary, playback speed is down from 1x to ½ or ¼ by pressing [D OWN] button, Pl ayback speed lo wer than ¼ is practically meaningless, and we recommend our users to freeze picture by pressing [FRZ] button and move picture by pic ture by pressing [LEFT] or [RIGHT] button for more precise search.

CH-01

CH-02 CH-03

CH-04 CH-05 CH-06

CH-07 CH-08

[UP] button

1X PLAY SPE ED 2X PLAY SPE ED 4X PLAY SPE ED

8X PLAY SPE ED 16X PLAY SPEED 32X PLAY SPEED 60X PLAY SPEED

[DOWN] button

1/2 PLAYSPEED 1/4 PLAYSPEED

03 / 10 / 25 16 : 11 : 38

R 12.34% P 5.03%

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

8. TCP/IP SETUP

Press [ENTER] button when half-tone green bar is on TCP/IP SETUP.

TCP/IP SETUP

MAC ADDR . . . 00-01-A2-0 1-1E-77 IP ADDRESS

IP PORT SUBNET MASK GATEWAY DHCP SETUP

TCP/IP SETUP

SELECT , THEN ENTER

TCP/IP setup must be done correctly to access to DVMR unit via IP network from clie nt PC far apar t from D VM R unit. MAC ADDRESS is not allowed for users to change and it is very unique number assigned by manufacturer as per IEEE regulation. IP ADDRESS, IP PORT, SUBNET MASK, and GATEWAY are what users must input manu ally, or our DV MR can get those data automatically in case DVMR unit is connected directly to DHCP server in IP network.

To input each element of IP data, move small triangular cursor to the item you want to change, and pre ss [ENTER] button, then you can change using [UP]/[DOWN] and [LEFT]/[RIGHT] button.

1) Concept of accessing to DVMR unit via IP network

DVMR unit

PTZ

Camera

LAN, WAN, or Internet

Client program (remote viewer)

TCP/IP setup

2) Conditions of IP network

a) Accessing to DVMR unit in the same Intranet(LAN)

DHCP server

Router/Gateway IP Sharer

DVMR unit

LAN

b) Accessing to DV MR unit via Inter net line

InternetPC

Leased line w/ static IP

Cable modem w/ dynamic IP

DVMR unit Client program (remote viewer)

InternetPC

ADSL

modem

dynamic IP

static IP

DVMR unit

Client program

(remote viewer)

Router

Gateway

PPPoE protocol

Port Forwarding (IP Forwarding)

For more details of TCP/IP setting in DVMR unit and PC, refer to “Remote Viewer manual”.

DHCP SETUP

Automatic

Other devices

: 192. 168. 1. 171 : 8000 : 255. 255. 255. 0 : 192. 168 . 1. 1 : MANUAL

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

5) BAUDRATE SETUP To control PTZ camera connected to DVMR unit, you

have to set baud rate of communication between PTZ camera and DVMR unit.

To set baudrate, move half-tone green bar on baudrate you want to select, and press [ENTER] button then CURRENT VALUE is changed to the value you selected.

To save settings and exit, press [MENU] button.

BAUDRATE SETUP

2400 BPS CURRENT SPEED 4800 BPS 9600 BPS 9600 BPS 19200 BPS

BAUDRATE SETUP

SELECT , THEN ENTER

1200 BPS

CONFIRMATION VIA RS485 PORT on the bottom of BAUDRATE SETUP is to test if communication between DVMR unit and PTX camera with set baudrate is do ne correctly. Move half-tone green bar to CONFIRMATION VIA RS485 PORT, and press [ENTER] button. Then you can see TEST STRING sent by DVMR unit is displayed on your PC, in case you also connected DVMR u nit to PC via RS232C port.

6) PASSWORD SETUP You can set your own password in PASSWORD SETUP.

DVMR system verify users entering into SET UP menu and users who input correct password is allowed to access SETUP menu and change any settings in SETUP menu. Also, you have to in put proper passw o r d in SET TIN G in remote viewer(client program) to access DVMR unit via IP network, too.

Memorize new password and also keep it secretly. In case you forgot password, contact dealer from which you purchased DVMR unit. All of our dealers have master password which will enable s you to enter into PASSWORD SETUP menu to generate new password.

CURRENT PASSWORD : --- ---- NEW PASSWORD : ------- CONFIRM PASSWORD : --- -----

INPUT YOU R OWN PASSWO RD, THEN PRESS [ENTE R]

PASSWORD SETUP

TO EXIT, PRESS [MENU]

Sequence to change password is as follows.

- Input current password in the first line and press [ENTER].

- Input new password in the second line and press [ENTER].

- Input new password again to confirm it and press [ENTER].

- Then “PASSWOR D CHANGE” is displayed and changing password is completed.

8 channel stand-alone DVMR

3. Operation

1. Basic Operation

To go back to the very first SETUP condition recommended by manufacturer, set at FACTORY DEFAULT.

SYSTEM SETUP

HDD MANAGEM EN T

RECORD SETUP

CAMERA S ETUP

TIME/DAT E SETUP

MISCELLANE OUS SETUP

FACTORY DEFAULT

SELECT UP/DOWN , ENTER

SYSTEM SETUP

Items remain unchanged even aft er FACTORY DEFA ULT is done.

1. value of TIME/DATE SETUP

2. Date stored on HDD

4. ADMIN password

3. ALARM LIST SETUP

ALL ABOUT IMAGE RECOGNITION & PROCESSING

You can set at FACTORY DEFAULT all i n one (as a whole) or group by group. When cursor is at ALL SETUP, you can set at ON or OFF by pressing [ENTER] button. If you set ALL SETUP at ON, all groups of settings are SET as per FACTORY DEFAULT recommended by manufacturer. If you set ALL SETUP at OFF, then you are requested to set each group of settings separately one by one, ON or OFF, and groups of s ettings set at ON shall be reset whenever you set at FACTORY DEFAULT. To reset, you have to select ALL SET or each group of settings (ON or OFF), and then move to RUN and press [ENTER].

In SYSTEM SETUP, we can change different parameters for operation of DVMR system, as you like. However, we basically recommend our users to set at FACTORY DEFAULT, until you have full understanding about operation of DVMR system. To enter into SYSTEM SETUP, first press [MEN U] button , and enter password. After pa ssword, press [ENTER] button and you can enter into SY STEM SETUP. In the first operation of DVMR unit after you first install HDD or add 2nd HDD to DVMR unit, delete all data on HDD, whether it is used HDD or brand-new HDD, and set at FACTORY DEFAULT.

TCP/IP SETUP

2. CAMERA SETUP

CAMERA SETUP

MOTION SETUP

EDIT CAMERA TI TL E ADJUST COL OR

SELECT [UP]/[DOWN] , PRESS [LEFT]/[R IGHT]

CAMERA SETUP

In camera setup, we have 3 different sub-menu as follows.

1) Edit camera title Edit camera title.

2) Adjust color Adjust brightness, contrast and others relating to color of camera channel by channel.

3) Motion setup Set motion detection area, sensitivity, and detection window which specifies minimum s ize of object detected by the system.

8 channel stand-alone DVMR

3. Operation

3-4. SETUP

3. DISPLAY SETUP

EDIT CAMERA TITLE

CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ] CAM 1….. [ CH-01 ]

CAM , Char Pos Ente r

, : < > ( )

A B C D E F G

EDIT CAMERA TITLE

ALL ABOUT IMAGE RECOGNITION & PROCESSING

1) Edit camera title Camera tile is 9 characters in length and includes

alphabet in a capital letter or small let ter, numbers, and some special letters. Default camera title is CAM 1, CAM 2, and so on for channel 1, channel 2 and so on.

Moving to a channel you want to change is done by pressing [UP] and [DOWN] button, moving next character in a specific camera tile is done by pressing [ENTER] button. On the right side of display, there is series of letters in vertical, and letter just behind triangular cursor is written whenever you press [LEFT] or [RIGHT] button.

To save and exit EDIT CAMERA TITLE mode, press [MENU] button.

ADJUST COLOR

CH NUMBER 1 BRIGHTNESS -1 CONTRAST +3 SATURATION +0 HUE -1 GAIN -3

SELECT , PRESS

ADJUST COLOR

2) Adjust colors You can change parameter of ca m er a col o r lik e

brightness, contrast, and others for each channel. First select channel number whose parameters you

want to change, using [LEFT] and [RIGHT] button. When you select channel, image from selected channel is displayed. Then select element you want to change by pressing [UP] and [DOWN] button and adjust by pressing [LEFT] and [RIGHT] button. You can see how it looks like whenever you change values. After you adjust parameters for channel you selected, then select next channel for ch ange. To save and exit ADJUST COLOR mode, press [MENU] button.

CELL CAM 01 ON X08Y07

SELECT : MENU EDIT : ENTER/

MOTION SETUP

3) Motion setup In motion setu p mode, you can set motion detecti on

area, sensit ivity of motion, and detect windowrespectively, channel by channel.

It is very important to set motion detection area, sensitivity, and detect window, when you are going to record just when motion is detected. Motion detection area is important because DVMR system just recognize motion in this area. Sensitivity of motion specifies the sensitivity with which DVMR system detect motion, and very slow movement may not be detected if sensitivity of motion is set at very low level. Detection windows specifies size of moving object, and DVMR system does not detect moving object which is smaller in numbers of cell than detection windows fixed in advance.

Cell(16x12) in green color indicates detection area, and color change to violet color in cells represents motion is detected

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

2) ALARM SETUP In DVMR system, 8 alarm input, one for each channel,

and 1 alarm output(relay out) is provided, and we can set type of alarm sensor independently in ALARM SETUP.

Or you can set all of input alarm sensors at “NO”, “NC” or DISABLE by setting ALL at “NO”, “NC” or DISABLE, by pressing [ENTER] button or [LEFT] or [RIGHT] button.

To save settings and exit, press [MENU] button.

ALARM SETUP

ALL : - CH 01 : NO CH 02 : NO

CH 03 : NO CH 04 : NO CH 05 : NO CH 06 : NO CH 07 : NO CH 08 : NO

RELAY : ENABLE

NO . . . . . NORMAL OPEN

NO . . . . . NORMAL CLOSE

- - . . . . . DISABLE

ALARM SETUP

SELECT , EDIT ENTER /

In the same way, we can set type of relay out at “NO”, “NC” or DISABLE, by pressing [ENTER] button or [LEFT] or [RIGHT] button.

3) TIMER SETUP In DVMR system, we have 3 kind of tim er settings as

follows.

To save settings and exit, pres s [ M EN U ] bu tt o n.

TIMER SETUP

FULL SCREEN : 1 SEC QUAD SCREEN : 3 S EC PIP SCREEN : 2 SEC

TIMER SETUP

SELECT , EDIT ENTER /

FULL SCREEN timer :

Rotating cycl e time of full screen in live mode, when [SEQ] button is pressed for long time .

QUAD SCREEN timer :

Rotating cycle time of quad(4-split) screen in live mode, when [SEQ] button is pressed for long time.

PIP SCREEN timer :

Rotating cycle time of PIP screen in live mode, when [PIP] button is pressed in live mode. If you press [SEQ] button for long time, full screen picture also rotates with time interval of FULL SCREEN timer, in addition to PIP.

4) PAN/TILT CMD SETUP Just with operation buttons on the fro nt panel of DVMR

unit, we can control PTZ camera connected to DVMR unit via RS-485 port, if protocol of PTZ camera connected to DVMR unit is same as one of built-in protocols, just select model among models in PAN/TILT CMD SETUP. In case PTZ camera you connected to DVMR unit is not a model whose protocol in incorporated into DVMR unit, you are requested to select USER DEFINE and input protocol by yourself.

To save settings and exit, pres s [ M EN U ] bu tt o n.

PAN/TILE CMD SETUP

MODEL : PELCO D TYPE P-SPD : 80 T-SPD : 80

Z-SPD : 80 F-SPD : 80 DEV : 1 ST

CMD : POWER ON LEN : 07 BYTE DELA Y : 15

COPY : REC PAS TE : PLAY

PAN/TILT CMD SETUP

SELECT , EDIT NUMERIC /

NO HEXA

---- ------ 01 -- FF 02 -- 01 03 -- 88 04 -- 00 05 -- 00

NO HEXA

---- ------ 06 -- 00 07 -- 89 08 -- 00 09 -- 00 10 -- 00

NO HEXA

---- ------ 11 -- 00 12 -- 00 13 -- 00 14 -- 00 15 -- 00

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

6. HDD MANAGEMENT

Press [ENTER] button when half-tone green bar is on HDD MANAGEMENT.

HDD MANAGEMENT

HDD CLEAR [ IN USE ] HDD INFORMATION CD-R BACK UP

HDD MANAGEMENT

SELECT , PRESS EN TER

1) HDD CLEAR When DVMR system st arted to recor d and hard driv e has

data of pictures recorded, “IN USE” is displayed in square brackets.

You are strongly requested to clear data on hard drive, when you first install hard drive or you add second hard drive, whet her it is used one or brand new one after setting at FACTORY DEFAULT.

2) HDD INFORMATION Press [ENTER] button when half-tone green bar is on HDD MANAGEMENT to enter into HDD

INFORMATION.

If you want to delete all data on hard drive, press [ENTER] when half-tone green bar is on “HDD CLEAR”. Then DVMR system asks you to enter password. Enter password and press [ENTER], and “EMPTY” is displayed in square brackets.

In HDD INFORMATION, you can have information of HDDs as follows.

- Date of detecting HDD

- Drive number fr om 1 to 22

- Manufacturer and mo del of HDD

- Capacity(GB) of HDD detected

7. MISCELLANEOUS SETUP

Press [ENTER] button when half-tone green bar is on MISCELLANEOUS SETUP.

BUZZER SETUP

ALL BUZZER --KEY BEEP ON LOSS EVENT OFF ALARM EVENT ON MOTION EVENT OFF

BUZZER SETUP

SELECT , EDIT ENTER /

1) BUZZER SETUP In DVMR system, we can set buzzer “ON” or “OFF” for

key, video loss, alarm event, and motion event independently, in BUZZER SETUP.

Or you can set all of them at “ON” or “OFF” by setting ALL BUZZER at “ON” or “OFF”, by pressing [ENTE R} button.

In MISCELLANEOUS SETUP, we can set parameters for buzzer, alarm, timer(time interval), pan/tilt command, baud rate of RS-485, and password.

To save settings and exit, press [MENU] button.

8 channel stand-alone DVMR

3. Operation

3) CD-R BACKUP Press [ENTER] button when half-tone green bar is on CD-R BACK UP to back up the recorded

data. For more details, pl ea se re fe r to the attac he d Gui de Li ne paper for thi s fu nctio n.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

CELL CAM 01 ON X08Y07

SELECT : MENU EDIT : ENTER/

MOTION SETUP

In the display on the left, “CELL” on the top left is glittering, and x and y coordinates on the top right represent location of cell in selected channel, red in color, you can edit . Just besides triangular cursor on the top left shows if cell glittering in red color is “ON” or “OFF”.

When status of cell glitte ring in red color is “ON”, press [ENTER] but ton to change status of this cell to “OFF”, which means not to detect motion in this cell. If you press [ENTER] button when it is in “OFF”, then it is changed to “ON” and motion is detected in this cell.

Fix motion detection area cell by cell

If you press [MENU] button, display on the top left changed to “BLOCK ON” and you can set motion detect ion area block by block, as follows.

BLOCK ON CAM 01 BEGIN X08Y07 END

SELECT : MENU EDIT : ENTER/

MOTION SETUP

Fix motion detection area block by block

To set motion detection area block by block , first press [ENTER] button and small triangular cursor shall be displayed just in front of “BEGIN”. Then move cell glittering in red color to a position you want and press [ENTER] button again, then coordinates of cell you selected is di splayed just on the right of “BEGIN” and small triangular cursor is displayed just in front of “END”. Again, move cell glittering in red color to other position and press [ENTER] button. Then cells belong to rectangular area you defined shall be changed to green color and these cells are set as motion detection ar ea . Yo u ca n r ep ea t t hi s pro cess until you complete motion detection set up.

Cancel motion detection area block by block

Just as you set motion detectio n area block by block, you can cancel motion det ection area you set, block by block. To cancel detection area blo ck by block, press [MENU] button until “BLOCK O FF’ is displayed on the top left. Then you can set block just like you set motion d etection area block by block.

Cancel or set mo tion detectio n area as a whole(all cells of 16x12)

In case you want set all cells(16x12) as motion detection area or set all cells “OFF”, press [MENU] button until “ALL” is displayed on the top left. Then press [ENTER] to make all cells detect motion or not detect motion.

Adjusting sensitivity of motion detection

Press [MENU] button again until “SENSITIVITY” is displayed on the top left. After “SENSITIVITY” is displayed, press [UP] OR [DOWN] button to adjust sensitivity level from 1 to 10. In higher values, it detect motion more sensitively. If it is very low, very slow movement is not detected, even though moving object is bigger than detect window and movement is in detection area.

Set detect window

Press [MENU] button again until “DETECT WINDOW” is displayed on the top left. Detect window is set in numbers from 1 to 20, and it represent size of moving object. Practically number represents numbers of cells(in total, 16x12), and detect window implies relative size of moving o bject displayed in the monitor connected to DVMR unit. Just in case movement is detected in cells more than detect window, DVMR system recognize motion is detected.

To exit

Press [MENU] button until “EXIT’ is displayed on the top left, and press [ENTER] button to save settings and exit.

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

4. TIME/DATE SETUP

Press [ENTER] button when half -t one green bar is on TIME/DATE SETUP.

SET TIME/DATE

YEAR MONTH 2003/10/06 DAY HOUR 22:41:5 2 MINUTE SECOND

SET TIME/DATE

SELECT , PRESS

Select items you want to change using [UP] and [DOWN] buttons, and change values using [LEFT] and [RIGHT] buttons.

After you set all , press [MENU] but ton to save you se t and exit.

5. RECORD SETUP

Press [ENTER] button when half- t on e gr e en bar is in on RECORD SETUP.

RECORD SETUP

OVERWRIT E TIME INTERV AL EVENT OFF TIMER REFRESH RATE DURATION

RECORD SETUP

SELECT , PRESS

1) RECORD TYPE When half-tone green bar is on RECORD TYPE, press

[LEFT] or [RIGHT] button to select recording mode you want.

TIMER recording type indicates recording continuously at set recording speed(TIME INTERVAL).

MOTION recordi ng type indicates recording just in case motion is detected for DURATION time at set recording speed (TIME INTERVAL).

ALARM represent recording just in case al arm is activated for DURATION time at set recording speed(TIME INTERVAL).

RECORD TYPE

2) OVERWRITE Move half-tone green bar to OVERWRITE to set if you will overwrite or stop recording when hard drive is full

and just display warning mes s age.

Press [LEFT] or [RIGHT] button to set at “ON” or “OFF”. “ON” implies overwriting allowed when hard drive is full, while “OFF” implies stop recording when it is full.

We recommend to set at “ON” not to make DVMR unit stop recording only with the reason it is full with data.

: TIMER : ON : 1/1 X : 60 SEC : -----: ------

8 channel stand-alone DVMR

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

RECORD SETUP

RECORD TYPE : TIMER OVERWRITE : O N : 1/1 X EVENT OFF TIMER : 60 SEC REFRESH RATE : ----- DURATION : ------

RECORD SETUP

SELECT , PRESS

3) TIME INTERVAL

When half-tone green bar is on TIME INTERVAL, press [LEFT] or [RIGHT] button to select recording speed you want.

TIME INTERVAL set here is applied for all RECORDING TYPE, that are, TIMER, MOTION, or ALARM.

Recording sp eed for each TIME INTERVAL is as follows. (based on NTSC system)

1/1 x : 60 fields/sec in total 1/2 x : 30 fields/sec in total 1/3 x : 20 fields/sec in total 1/ 4 x : 15 fields/sec in total

. . . and so on

TIME INTERV AL

TIME INTERVAL implies recording speed, and 1/1 represents maximum recoding speed of this DV MR system, that is 60 fields/sec in total.

4) EVENT OFF TIMER

For example, if you set EVENT OFF TIMER at 60 sec, and motion detected now is detected less than 60 sec after previous motion, it is not enlisted in event list. However, motion detect now is after more than 60 sec, it is enlisted in event list. It is same for alarm or video loss.

EVENT OFF TIMER is to restrict event to be enlisted in event list, and it is useful in case you set recording mode at motion detection mode, alarm mode. In case motion is detected very frequently, event list shall be full with just motion detected, and it is meaningl es s to have such event li st.

EVENT OFF TIMEER sets time interval between event(video loss, motion detected, and alarm) to event not to enlist envent which happen too frequently.

Default value set by manufacturer is 60 sec.

5) REFRESH RATE When you recor d in motion recording mode, and motion is det ected in one of 8 channel and no

motion is detected in all other channels in some times. In this case, we may see pictures fairly long hours ago in playback in channels where no motion is detected, while pictures in a channel where we have many motion detected is updated very frequently.

Refresh rate is time interval for recording pictures from channels where no motion is detected for a long time. That is, even th ough there is no motion detec ted, DVMR system records an image as per this REFRESH RATE time interval to show relatively recent pictures in corresponding channels, e v en though there are no motions detected.

6) DURATION It is motion duration or alarm duration. When DVMR records in motion recording mode or alarm recording mode, it records for DURATION time in case motion is detected or alarm is activated, respectively.

8 channel stand-alone DVMR

4. Configuration

Gen IV Technology 8 CH STAND-ALONE DVMR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual