Genesis GDP1005A User Manual
10" 5-Speed Drill Press
Perceuse à colonne de 10 po., 5 vitesses
Taladro de pie de 10”, 5 velocidades
Operator’s Manual
Manuel d’utilisation
Manual del operario
GDP1005A
TOLL FREE
HELP LINE:
WEBSITE:
888-552-8665
www.genesispowertools.com
SPECIFICATIONS
• Model: -------------------------------- GDP1005A
• Rated Power: ------------------------- 120V~ /60 Hz, 4.1 Amp
• No Load Speed: ----------------------- 5 Speeds (620, 1150, 1630, 2180, 3070 RPM)
• Chuck Size: --------------------------- 5/8” (16mm)
• Spindle Travel: ------------------------ 2” (50mm)
• Swing: -------------------------------- 10” (254mm)
• Table Movement:---------------------- 45° bevel, 360° swivel
• Table Size: ---------------------------- 7-1/4” x 7-1/4” (184mm x 184mm)
• Base Size: ---------------------------- 13-3/8” x 8-1/4” (340mm x 210mm)
• Max. Distance from Spindle End to Surface of Table:-------- 12-3/16” (310mm)
English
• Max Distance from Spindle End to Surface of Base: --------- 17-1/4” (438mm)
• Max Distance from Spindle Axis to Surface of Column: ----- 5 ” (127mm)
• Net Weight: ------------------------------------------------- 49.5 Lbs
Includes: Chuck Key, 2 Allen Wrenches and 2 “AAA” Batteries for Work Light
WARNING: To reduce the risk of injury, user must read and understand this
operator’s manual before operating this tool. Save this Manual for future reference.
Toll-Free Help Line: 1-888-552-8665
WEAR YOUR
SAFETY GLASSES
FORESIGHT IS BETTER
THAN NO SIGHT
WARNING: The operation of any power tool can result in foreign objects
being thrown into your eyes, which can result in severe eye damage. Before beginning
tool operation, always wear safety goggles or safety glasses with side shields and a
full face shield when needed. We recommend Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields. Always wear eye protection
which is marked to comply with ANSI Z87.1.
Look for this symbol to point out important safety
precautions. It means attention!! Your safety is involved.
GENERAL SAFETY RULES
WARNING: Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles
WARNING: Read and understand all warnings, cautions and operating
instructions before using this equipment. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
.
2
Operator’s Manual GDP1005A
10" Drill Press
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
•
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs in any earthed (grounded) power tools. Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized
outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded
power cord and grounded power supply system.
•
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
•
Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is
grounded.
•
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk of electric shock.
•
When operating a power tool outside, use an extension cord suitable for
outdoor use. These cords are rated for outdoor use and reduce the risk of electric shock.
•
Do not use AC only rated tools with a DC power supply. While the tool may appear to
work. The electrical components of the AC rated tool are likely to fail and rate a hazard to the operator.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
•
Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection for appropriate conditions will reduce personal injuries.
•
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents may cover moving
parts and should be avoided.
•
Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying
power tool with your finger on the switch or plugging in power tools that have the switch on invites accidents.
•
Remove any adjusting keys or wrenches before turning the power tool on. A
wrench or key that is left attached to a rotating part of the tool may result in personal injury.
•
Do not overreach. Maintain proper footing and balance at all times. Loss of balance can cause an
injury in an unexpected situation.
•
If devices are provided for connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices can
reduce dust related hazards.
•
Do not use a ladder or unstable support. Stable footing on a solid surface enables better
control of the tool in unexpected situations.
•
Keep tool handles dry, clean and free from oil and grease. Slippery handles cannot
safely control the tool.
TOOL USE AND CARE
• Secure the workpiece. Use a clamp or other practical way to hold the workpiece to a stable
platform. Holding the workpiece by hand or against your body is unstable and may lead to loss of control.
•
Do not force the power tool. The tool will perform the job better and safer at the feed rate for
which it is designed. Forcing the tool could possibly damage the tool and may result in personal injury.
•
Use the correct power tool for the job. Don’t force the tool or attachment to do a job for
which it is not designed.
English
3
• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired or replaced by an authorized service center.
•
Turn power tool off, and disconnect the plug from the power source and/or battery pack
from the power tool before making any adjustments, changing the accessories, or storing the tools. Such
preventive safety measures reduce the risk of an accidental start up which may cause personal injury.
Store idle tool out of reach of children and other inexperienced persons. It is
•
dangerous in the hand of untrained users.
•
Maintain power tools with care. Check for improper alignment, binding of moving parts,
component breaks, or any other conditions that may affect the tool’s operation. A guard or any other part that is
damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.
•
Use recommended accessories. Using accessories and attachments not recommended by the
manufacturer or intended for use on this type tool may cause damage to the tool or result in personal injury to
English
the user. Consult the operator’s manual for recommended accessories.
•
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
•
Feed the workpiece in the correct direction and speed. Feed the workpiece into a
blade, cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly
feeding the workpiece in the same direction may cause the workpiece to be thrown out at high speed.
•
Never leave the tool running unattended, turn the power off. Do not leave the tool
until it comes to a complete stop.
•
Never start the power tool when any rotating component is in contact with
the workpiece.
WARNING: USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR
OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST
AND ASBESTOS. Direct particles away from face and body. Always operate tool in a
well-ventilated area and provide for proper dust removal. Use dust collection system
wherever possible. Exposure to the dust may cause serious and permanent respiratory
or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid
breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into
your mouth or eyes, or lay on your skin may promote absorption of harmful material.
Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for
dust exposure, and wash exposed areas with soap and water.
SERVICE
• Have your power tool serviced by a qualified repair person using
replacement parts. This will ensure that the safety of the power tool is maintained.
•
Service your power tool periodically. When cleaning a tool, be careful not to disassemble any
portion of the tool since internal wires may be misplaced or pinched.
only identical
SAVE THESE INSTRUCTIONS
EXTENSION CORDS
Grounded tools require a three wire extension cord. Double insulated tools can
use either a two or three wire extension cord. As the distance from the power supply outlet increases, you must
use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop
in voltage, resulting in loss of power and possible tool damage. Refer to the table shown below to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-gauge cord
can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total
length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for
more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.
4
10" Drill Press
Operator’s Manual GDP1005A
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to
indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)
Nameplate
Amperes
(At Full Load)
0– 2.0 18 18 18 18 16 16
2.1–3.4 18 18 18 16 14 14
3.5– 5.0 18 18 16 14 12 12
5.1–7.0 18 16 14 12 12 10
7.1–12.0 18 14 12 10 8 8
12.1–16.0 14 12 10 10 8 6
16.1–20.0 12 10 8 8 6 6
Extension Cord Length
25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet
SPECIFIC SAFETY RULES FOR DRILL PRESSES
WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT
(GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY
RULES. If you use this tool unsafe or incorrectly, you can suffer serious personal injury!
Make sure the drill press is on a firm, level surface and properly secured to avoid injury
•
from unexpected movement. Firmly clamp or bolt the drill press to a support surface to prevent slipping or
sliding during the operation.
• Unplug the drill press before making adjustments, repairs, maintenance or storing.
•
Always switch off the drill press before unplugging it to avoid accidental starting when re-
plugging the tool into a power source.
•
Use recommended speeds for drill accessories and workpiece material.
•
Allow the motor to come up to full speed before drilling to avoid binding or stalling.
•
Wear eye protection. Do not wear gloves, necktie, or loose clothing.
•
Before starting the operation, jog the motor switch to make sure the drill bit or other
cutting tool does not wobble or cause vibration.
• Keep hands away from work area. Keep hands away from the bit.
•
Be sure drill bit or cutting tool is securely locked in the chuck.
• Always clamp workpiece or brace against column to prevent rotation. Never use your
hand to hold the workpiece while drilling.
•
Make sure the pulley housing cover is down and the chuck is installed properly before
engaging the power switch.
•
Keep bits clean and sharp. Sharp bits minimize stalling.
•
Lock the switch off when leaving the drill press.
•
Before starting, be sure chuck key is removed from the chuck and the motor head and
table are locked.
•
Never start the drill press when the bit or other cutting tool is in contact with the workpiece.
•
Adjust the table or depth stop to avoid drilling into the table.
•
When using a drill press vise, always fasten the vise to the table.
•
Do not operate in rain or in damp locations.
• Grounding required.
English
SAVE THESE INSTRUCTIONS
5
Loading...