General Semiconductor UGF10DCT, UGF10CCT, UGF10BCT, UGF10ACT Datasheet

NEW PRODUCT NEW PRODUCT NEW PRODUCT

0.060 (1.52)

0.405 (10.27)

0.383 (9.72)

0.670 (17.2)

0.646 (16.4)

0.191 (4.85)

0.171 (4.35)

0.600 (15.5)

0.580 (14.5)

0.560 (14.22)

0.530 (13.46)

0.037 (0.94)

0.027 (0.69)

0.140 (3.56)

0.130 (3.30)

0.350 (8.89)

0.330 (8.38)

0.188 (4.77)

0.172 (4.36)

0.110 (2.80)

0.100 (2.54)

0.131 (3.39)

0.122 (3.08)

0.110 (2.80)

0.100 (2.54)

0.022 (0.55)

0.014 (0.36)

0.105 (2.67)

0.095 (2.41)

0.205 (5.20)

0.195 (4.95)

PIN 1

PIN 3

PIN 2

DIA

DIA.

UGF10ACT THRU UGF10DCT

ULTRAFAST SOFT RECOVERY RECTIFIER

Reverse Voltage - 50 to 200 Volts Forward Current - 10.0 Amperes

ITO-220AB

FEATURES

♦ Plastic package has Underwriters Laboratories

Flammability Classification 94V-0

♦ Ideally suited for free wheeling diode power factor

correction applications

♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Optimized to reduce switching losses ♦ High temperature soldering guaranteed:

250°C/10 seconds at terminals

♦ Glass passivated chip junction

MECHANICAL DATA

Case: JEDEC ITO-220AB molded plastic body Terminals:Plated leads, solderable per MIL-STD-750,

Method 2026

Polarity: As marked Mounting Position: Any Mounting T orque: 5 in.- lbs. max. Weight: 0.08 ounce, 2.24 grams

Dimensions in inches and (millimeters)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS

Maximum repetitive peak reverse voltage V Working peak reverse voltage V Maximum RMS voltage V Maximum DC blocking voltage V Maximum average forward rectified current at T

=100°C I

Peak forward surge current

8.3ms single half sine-wave superimposed I on rated load (JEDEC Method) per leg

Maximum instantaneous forward voltage per leg at I

Maximum reverse leakage current per leg T at working peak reverse voltage T

Maximum reverse recovery time per leg at I

=1.0A, di/dt=100A/µs, VR=30V, Irr=0.1 I

Maximum reverse recovery time per leg at Maximum 25 I

=0.5A, IR=1.0A, Irr=0.25A Typical

Maximum reverse recovery current per leg at I

=5A, di/dt=50A/µs,VR=30V

Maximum stored charge per leg Maximum 5.5 I

=2A, di/dt=20A/µs, VR=30V Irr=0.1 I

Typical ther mal resistance from junction to case per leg R Operating junction and storage temperature range T

=10A, TJ=25°C 1.25

=5A, TJ=25°C V

=5A, TJ=150°C 0.895

=25°C 10

=100°C

Typical

, T

UGF10ACT UGF10BCT UGF10CCT UGF10DCT

RRM

RWM

RMS

(AV)

FSM

ΘJC

STG

50 100 150 200 Volts 50 100 150 200 Volts 35 70 105 140 Volts

100 100 200 200 Volts

10 Amps

60 Amps

1.10 Volts

200

25 ns

0.7 Amps

4.5

6.0 °C/W

-40 to +150 °C

UNITS

µA

NOTICE: Advanced product information is subject to change without notice

4/98

100

125

150

100

0.2

0.4

0.6

0.8

1.0

1.2

1.4

0.01

0.1

100

125

0.1

100

0.1

100

1,000

RATINGS AND CHARACTERISTIC CURVES UGF10ACT THRU UGF10DCT

AVERAGE FORWARD CURRENT, AMPERES

FIG. 1 -FORWARD CURRENT DERATING CURVE

RESISTIVE OR INDUCTIVE LOAD

CASE TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS PER LEG

TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE

TJ=125°C

TJ=100°C

PEAK FORWARD SURGE CURRENT,

AMPERES

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FORWARD SURGE CURRENT PER LEG

8.3ms SINGLE HALF SINE-WAVE (JEDEC Method)

=105°C

NUMBER OF CYCLES AT 60 H

FIG. 4 - TYPICAL REVERSE CHARACTERISTICS

PER LEG

TJ=125°C

TJ=100°C

AMPERES

INSTANTANEOUS FORWARD CURRENT,

nC/ns

STORED CHARGE/REVERSE RECOVERY TIME,

TJ=25°C

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS

FIG. 5 - REVERSE SWITCHING CHARACTERISTICS

PER LEG

@2A, 20A/µs

@5A, 50A/µs

@1A, 100A/µs

@5A, 50A/µs

@1A, 100A/µs

@2A, 20A/µs

JUNCTION TEMPERATURE, °C

MICROAMPERES

TJ=25°C

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %

TJ=125°C f=1.0 MHz Vsig=50MVp-p

CAPACITANCE, pF

REVERSE VOLTAGE, V OLTS