General Semiconductor RS2A, RS2B, RS2G, RS2D, RS2J Datasheet
...
RS2A THRU RS2K
0.160 (4.06)
0.180 (4.57)
0.006 (0.152)
0.012 (0.305)
0.030 (0.76)
0.060 (1.52)
0.008 (0.203)
0.205 (5.21)
0.220 (5.59)
0.084 (2.13)
0.096 (2.44)
0.077 (1.95)
0.086 (2.20)
0.130 (3.30)
0.155 (3.94)
MAX.
SURFACE MOUNT FAST SWITCHING RECTIFIER
Reverse Voltage - 50 to 800 Volts Forward Current - 1.5 Amperes
DO-214AA
MODIFIED J-BEND
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ For surface mount applications
♦ Low profile package
♦ Built-in strain relief,
ideal for automated placement
♦ Glass passivated chip junction
♦ Fast switching for high efficiency
♦ High temperature soldering:
250°C/10 seconds at terminals
MECHANICAL DATA
Case: JEDEC DO-214AA molded plastic over
passivated chip
Terminals: Solder plated solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode band end
Weight: 0.003 ounce, 0.093 gram
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS RS2A RS2B RS2D RS2G RS2J RS2K UNITS
Device marking code RA RB RD RG RJ RK
Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current
=100°C
at T
L
RRM
RMS
I
(AV)
DC
50 100 200 400 600 800 Volts
35 70 140 280 420 560 Volts
50 100 200 400 600 800 Volts
1.5 Amps
Peak forward surge current
8.3ms single half sine-wave superimposed on I
FSM
50.0 Amps
rated load (JEDEC Method)
Maximum instantaneous forward voltage at 1.5A V
Maximum DC reverse current T
at rated DC blocking voltage T
Maximum reverse recovery time
Typical junction capacitance
Typical thermal resistance
(NOTE 1)
(NOTE 2)
(NOTE 3)
Operating junction and storage temperature range T
NOTES:
(1) Reverse recovery test conditions:IF=0.5A, IR=1.0A, Irr=0.25
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient and junction to lead
P.C.B.mounted on 0.27 x 0.27” (7.0 x 7.0mm) copper pad areas
=25°C 5.0
A
=125°C
A
F
I
R
t
rr
C
J
R
ΘJA
R
ΘJL
, T
J
STG
150 250 500 ns
1.30 Volts
200.0
50.0 pF
55.0
18.0
-55 to 150 °C
µA
°C/W
4/98
80 16050 60 70 90 100110120130140150
0
0.5
1.5
110100
0
10
20
30
40
50
1.6 1.80.4 0.6 0.8 1.0 1.2 1.4
0.1
1
10
20
10
100
110100
1.0
0 20406080100
0.1
1
10
100
0.01
RATINGS AND CHARACTERISTIC CURVES RS2A THRU RS2K
FIG. 1 - FORWARD CURRENT DERATING CURVE
RESISTIVE OR
INDUCTIVE LOAD
AMPERES
P.C.B.MOUNTED
AVERAGE FORWARD CURRENT,
0.27 x 0.27” (7.0 x 7.0mm)
COPPER PAD AREAS
LEAD TEMPERATURE, °C
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
TL=100°C
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
AMPERES
PEAK FORWARD SURGE CURRENT,
NUMBER OF CYCLES AT 60 H
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
Z
TJ=125°C
AMPERES
INSTANTANEOUS FORWARD CURRENT
JUNCTION CAPACITANCE, pF
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
TJ=25°C
f=1.0 MH
Vsig=50mVp-p
MICROAMPERES
INSTANTANEOUS REVERSE CURRENT,
PERCENT OF RATED PEAK REVERSE
Z
VOLTAGE, %
TJ=25°C
REVERSE VOLT AGE, VOL TS
Loading...