General Semiconductor RGP10J, RGP10K, RGP10A, RGP10G, RGP10B Datasheet
...
RGP10A THRU RGP10M
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
DIA.
NOTE:
Lead diameter is for suffix "E" part numbers
0.026 (0.66)
0.023 (0.58)
®
GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere
DO-204AL
PATENTED*
Dimensions in inches and (millimeters)
*
Patent No.3,996,602 and brazed-lead assembly by Patent No.3,930,306
Glass-plastic encapsulation technique is covered by
FEATURES
♦ Plastic package has
Underwriters Laboratory
Flammability Classification 94V-0
♦ High temperature metallurgically
bonded construction
♦ Glass passivated cavity-free junction
♦ Capable of meeting environmental standards of
MIL-S-19500
♦ For use in high frequency rectifier circuits
♦ Fast switching for high efficiency
♦ 1.0 Ampere operation at TA=55°C with no thermal
runaway
♦ Typical IR less than 0.1µA
♦ High temperature soldering guaranteed:
350°C/10 seconds 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic over glass body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
Maximum recurrent peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current
0.375" (9.5mm) lead length at T
Peak forward surge current 8.3ms single half sine-wave
superimposed on rated load (JEDEC Method)
Maximum instantaneous forward voltage at 1.0A V
Maximum full load reverse current, full cycle average
0.375" (9.5mm) lead length T
Maximum DC reverse current T
at rated DC blocking voltage T
Maximum reverse recovery time
Typical junction capacitance
Typical thermal resistance
Operating junction and storage temperature range T
NOTES:
(1) Reverse recovery test conditions:IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B.mounted
4/98
A
=55°C
A
(NOTE 2)
(NOTE 3)
=55°C
(NOTE 1)
=25°C 5.0
A
=150°C
A
SYMBOLS 10A 10B 10D 10G 10J 10K 10M UNITS
RRM
RMS
DC
I
(AV)
I
FSM
I
R
I
R
t
rr
C
R
ΘJA
, T
J
RGP RGP RGP RGP RGP RGP RGP
50 100 200 400 600 800 1000 Volts
35 70 140 280 420 560 700 Volts
50 100 200 400 600 800 1000 Volts
1.0 Amp
30.0 Amps
F
1.3 Volts
100.0 µA
200.0
150 250 500 ns
J
15.0 pF
55.0 °C/W
STG
-65 to +175 °C
µA
25 50 75 100 125 150 175
0
0.25
0.5
0.75
1.0
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
1 10 100
1
10
100
110100
0
10
20
30
020406080100
0.01
0.1
1
10
20
0.01 0.1 1 10 100
0.1
1
10
100
RATINGS AND CHARACTERISTIC CURVES RGP10A THRU RGP10M
FIG. 1 - FORWARD CURRENT DERATING CURVE
AMPERES
0.375" (9.5mm) LEAD LENGTH
AVERAGE FORWARD RECTIFIED CURRENT,
AMBIENT TEMPERATURE, °C
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
RESISTIVE OR
INDUCTIVE LOAD
TJ=25°C
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
TJ=TJ max.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
AMPERES
FORWARD SURGE CURRENT,
NUMBER OF CYCLES AT 60 H
FIG. 4 - TYPICAL REVERSE
CHARACTERISTICS
TJ=125°C
Z
AMPERES
INSTANTANEOUS FORWARD CURRENT,
INSTANTANEOUS FORWARD VOLTAGE,
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PULSE WIDTH=300µs
1% DUTY CYCLE
VOLTS
TJ=25°C
f=1.0 MH
Z
Vsig=50mVp-p
TJ=75°C
MICROAMPERES
INSTANTANEOUS REVERSE CURRENT,
TJ=25°C
PERCENT OF RATED PEAK REVERSE
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
VOLTAGE, %
JUNCTION CAPACITANCE pF
REVERSE VOLTA GE, VOLTS
TRANSIENT THERMAL IMPEDANCE (°C/W)
t, PULSE DURATION, sec
Loading...