General Semiconductor RGL34B, RGL34D, RGL34G, RGL34J, RGL34A Datasheet

RGL34A THRU RGL34J

SOLDERABLE ENDS

1st BAND

2nd BAND

0.022 (0.559)

0.016 (0.406)

0.145 (3.683)

0.131(3.327)

D1=

0.066

0.060

(1.676)

(1.524)

D2 = D1

+ 0

- 0.008 (0.20)

1st band denotes type and polarity 2cnd band denotes voltage type

SURFACE MOUNT GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER

Reverse Voltage - 50 to 600 Volts Forward Current - 0.5 Ampere

FEATURES

DO-213AA

PATENTED*

Dimensions in inches and (millimeters)

Patent No.3,996,602 and brazed-lead assembly by Patent No.3,930,306

Glass-plastic encapsulation technique is covered by

♦ Plastic package has Underwriters Laboratory

Flammability Classification 94V-0

♦ For surface mount applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of

MIL-S-19500

♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed:

450°C/5 seconds at terminals. Complete device submersible temperature of 260°C for 10 seconds in solder bath

MECHANICAL DATA

Case: JEDEC DO-213AA molded plastic over glass body Terminals: Plated terminals, solderable per MIL-STD-750,

Method 2026 Polarity: Two bands indicate cathode end - 1st band denotes device type and 2nd band denotes repetitive peak reverse voltage rating

Mounting Position: Any Weight: 0.0014 ounce, 0.036 gram

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°°C ambient temperature unless otherwise specified.

Fast switching device: 1st band is Red Polarity color bands (2nd Band) Gray Red Orange Yellow Green

Maximum repetitive peak reverse voltage V Maximum RMS voltage V Maximum DC blocking voltage V Maximum average forward rectified current

=55°C

at T

Peak forward surge current

8.3ms single half sine-wave superimposed on rated load (JEDEC Method)

Maximum instantaneous forward voltage at 0.5A V Maximum DC reverse current T

at rated DC blocking voltage T

=25°C 5.0

=125°C

Maximum full load reverse current, full cycle average T

Maximum reverse recovery time Typical junction capacitance Maximum thermal resistance

Operating junction and storage temperature range T

NOTES: (1) Reverse recovery test conditions IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal (4) Thermal resistance from junction to terminal, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal

=55°C

(NOTE 1)

(NOTE 2)

(NOTE 3)

(

NOTE 4)

4/98

SYMBOLS RGL34A RGL34B RGL34D RGL34G RGL34J UNITS

50 100 200 400 600 Volts 35 70 140 280 420 Volts 50 100 200 400 600 Volts

0.5 Amp

10.0 Amps

1.3 Volts

50.0

30.0 µA 150 250 ns

4.0 pF

150.0

70.0

-65 to +175 °C

FSM

R(AV)

R R

, T

RRM RMS

(AV)

ΘJA ΘJT

STG

µA

°C/W

0 25 50 75 100 125 150 175

0.1

0.2

0.3

0.4

0.5

100

2.0

4.0

6.0

8.0

0.2 0.4 0.6 0.8 1.0

110100

1.2 1.4 1.6

0.1

0.01

020406080100

0.01

0.1

RATINGS AND CHARACTERISTIC CURVES RGL34A THRU RGL34J

FIG. 1 - FORWARD CURRENT

DERATING CURVE

CURRENT, AMPERES

AVERAGE FORWARD RECTIFIED

TERMINAL TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS

FORWARD CHARACTERISTICS

RESISTIVE OR INDUCTIVE LOAD

AMPERES

PEAK FORWARD SURGE CURRENT,

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FORWARD SURGE CURRENT

TJ=TJmax.

8.3ms SINGLE HALF SINE-WAVE (JEDEC Method)

NUMBER OF CYCLES AT 60 H

FIG. 4 - TYPICAL REVERSE CHARACTERISTICS

TJ=100°C

INSTANTANEOUS FORWARD CURRENT, AMPERES

INSTANTANEOUS FORWARD VOLT A GE, VOLTS

FIG. 5 - TYPICAL JUNCTION CAPACITANCE

PULSE WIDTH=300µs 1% DUTY CYCLE

TJ=25°C

TJ=25°C f=1.0 MHz Vsig=50mVp-p

MICROAMPERES

INSTANTANEOUS REVERSE CURRENT,

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %

TJ= 25°C

JUNCTION CAPACITANCE, pF

REVERSE VOLTAGE, VOLTS