0.147 (3.73)
0.137 (3.48)
0.144 (3.65)
0.161 (4.10)
0.106 (2.70)
0.090 (2.30)
0.190 (4.83)
0.179 (4.55)
0.029 (0.74)
0.017 (0.43)
0.012 (0.30)
0.008 (0.20)
0.105 (2.67)
0.095 (2.41)
0.047 (1.19)
0.038 (0.96)
0.205 (5.21)
0.195 (4.95)
0-10
°
0.117 (2.97)
0.107 (2.72)
0.028 (0.71)
0.020 (0.51)
0.016(0.41)
0.006 (0.15)
0.100 (2.54)
MIN.
0.049 (1.24)
0.039 (0.99)
PATENT PENDING PATENT PENDING PATENT PENDING
MB2M THRU MB6M
MINIATURE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse V oltage - 200 to 600 Volts Forward Current - 0.5 Ampere
Case Style MBM
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
FEATURES
♦ Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
♦ This series is UL recognized under Component Index,
file number E54214
♦ Glass passivated chip junctions
♦ High surge overload rating: 35A peak
♦ Saves space on printed circuit board
♦ High temperature soldering guaranteed:
260°C/10 seconds, at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Polarity: Polarity symbols marked on body
Mounting Position: Any
Weight: 0.078 ounce, 0.22 gram
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS MB2M MB4M MB6M UNITS
Device marking code 2 4 6
Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
RRM
RMS
DC
200 400 600 Volts
140 280 420 Volts
200 400 600 Volts
Maximum average forward output rectified
current at T
=30°C - on glass-epoxy P.C.B.
A
on aluminum substrate
(NOTE 1)
(NOTE 2)
Peak forward surge current 8.3msec. single half sinewave superimposed on rated load (JEDEC Method)
Rating for fusing (t<8.3ms) I
Maximum instantaneous forward voltage drop
per leg at 0.4A
Maximum DC reverse current at T
rated DC blocking voltage per leg T
Typical junction capacitance per leg
Typical thermal resistance per leg
Operating junction and storage temperature range T
NOTES:
(1) On glass epoxy P.C.B. mounted on 0.05 x 0.05” (1.3 x 1.3mm) solder pads
(2) On aluminum substrate P.C.B. with an area of 0.8 x 0.8 x 0.25” (20 x 20 x 6.4mm) mounted
on 0.05 x 0.05” (1.3 x1.3mm) solder pad
(3) Measured at 1.0 MHZand applied reverse voltage of 4.0 Volts
(NOTE 3)
(NOTE 1)
(NOTE 1)
(NOTE 2)
=25°C 5.0
A
=125°C
A
I
(AV)
0.5 Amp
0.8
I
FSM
2
t 5.0 A2sec
V
F
I
R
C
J
R
ΘJL
R
ΘJA
R
ΘJA
, T
J
STG
35.0 Amps
1.0 Volts
500
13.0 pF
20.0
85.0 °C/W
70.0
-55 to +150 °C
µA
RATINGS AND CHARACTERISTIC CURVES MB2M THRU MB6M
110100
0
5
10
15
20
25
30
35
0.2 0.4 0.6 0.8 1.0 1.2 1.4
0.01
0.1
1
10
0.1 1 10 100
0
5.0
10
15
20
25
30
200
0 20 40 60 80 100 120 140 160
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0 20 40 60 80 100
0.01
0.1
1
10
100
FIG. 1 - DERATING CURVE FOR OUTPUT
RECTIFIED CURRENT
GLASS
EPOXY
P.C.B.
AMPERES
AVERAGE FORWARD RECTIFIED CURRENT,
RESISTIVE OR INDUCTIVE LOAD
AMBIENT TEMPERATURE, °C
FIG. 3 - TYPICAL FORWARD VOLTAGE
CHARACTERISTICS PER LEG
ALUMINUM SUBSTRATE
P.C.B.
TJ=150°C
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
TA=40°C
SINGLE HALF SINE-WAVE
(JEDEC Method)
f=60 H
AMPERES
PEAK FORWARD SURGE CURRENT,
1.0 CYCLE
FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS
f=50 H
Z
NUMBER OF CYCLES
PER LEG
Z
TJ=125°C
PER LEG
TJ=25°C
PULSE WIDTH 300µs
1% DUTY CYCLE
AMPERES
INSTANTANEOUS FORWARD CURRENT,
INSTANTANEOUS FORWARD VOLTAGE,
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
VOLTS
JUNCTION CAPACITANCE, pF
REVERSE VOLTAGE, VOLTS
TJ=25°C
f=1.0 MH
Z
Vsig=50mVp-p
MICROAMPERES
TJ=25°C
INSTANTANEOUS REVERSE LEAKAGE CURRENT,
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %