General Semiconductor KBL08, KBL06, KBL02, KBL04, KBL10 Datasheet

...
KBL005 THRU KBL10
0.755 (19.18)
0.745 (18.92)
0.052 (1.32)
0.048 (1.22)
0.220 (5.59)
0.180 (4.57)
0.081 (2.06)
0.085 (2.18)
0.255 (6.48)
0.245 (6.22)
DIA.
1.1
(27.94)
MIN.
0.630 (16.0)
0.620 (15.75)
1.0
(25.4)
MIN.
SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 4.0 Amperes
FEATURES
Case Style KBL
Plastic material has Underwriters Laboratory Flammability
Classification 94V-0
This series is UL listed under the Recognized Component
High case dielectric
strength of 1500 V
RMS
Ideal for printed circuit boardsHigh forward surge current capabilityHigh surge current capabilityHigh temperature soldering guaranteed:
250°C/10 seconds, 0.375" (9.5mm) lead length, 5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any Weight: 0.2 ounce, 5.6 grams
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS 005 01 02 04 06 08 10 UNITS
Maximum repetitive peak reverse voltage V Maximum RMS voltage V Maximum DC blocking voltage V Maximum average forward output
current at TA=50°C Peak forward surge current single half sine-wave super-
imposed on rated load (JEDEC Method) T Maximum instantaneous forward voltage drop
per leg at 4.0A Maximum DC reverse current T
at rated DC blocking voltage per leg T Typical thermal resistance per leg
(NOTE 1) (NOTE 2)
=150°C
J
=25°C 5.0 µA
A
=125°C
A
Operating junction and storage temperature range T
NOTES:
(1) Thermal resistance from junction to ambient with units mounted on 3.0 x 3.0 x 0.11” thick (7.5 x 7.5 x 0.3cm) Al. plate (2) Thermal resistance from junction to lead with units mounted on P.C.B. at 0.375" (9.5mm) lead length and 0.5 x 0.5" (12 x 12mm) copper pads
R R
J
RRM RMS
I
(AV)
I
FSM
V
, T
DC
I
R
ΘJA ΘJL
KBL KBL KBL KBL KBL KBL KBL
50 100 200 400 600 800 1000 Volts 35 70 140 280 420 560 700 Volts 50 100 200 400 600 800 1000 Volts
4.0 Amps
200.0 Amps
F
1.1 Volts
1.0 mA
19.0
2.4
STG
-50 to +150 °C
°C/W
4/98
0 50 100 150
0
1.0
2.0
3.0
4.0
110100
25
50
75
100
125
150
175
200
0 20406080100120140
0.01
0.1
1
10
0.1 1 10 100
0
50
100
150
200
250
0.6 0.7
100
1.0
1
0.1
0.8 0.9 1.0 1.1 1.2 1.3
RATINGS AND CHARACTERISTICS CURVES KBL005 THRU KBL10
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
HEAT-SINK MOUNTED
3.0”sq. x 0.06” THK (7.5cm2x 0.15cm) COPPER PLATE
AMPERES
AVERAGE FORWARD CURRENT,
P.C.B. MOUNTED
0.375” (9.5mm) LEAD LENGTH 60 Hz RESISTIVE OR INDUCTIVE LOAD
TEMPERATURE, °C
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
SINGLE SINE-WAVE (JEDEC Method) TJ=150°C
AMPERES
PEAK FORWARD SURGE CURRENT,
FIG. 4 - TYPICAL REVERSE LEAKAGE
1.0 CYCLE
NUMBER OF CYCLES AT 60 Hz
CHARACTERISTICS PER LEG
TJ=100°C
AMPERES
INSTANTANEOUS FORWARD CURRENT,
INSTANTANEOUS FORWARD VOLTAGE,
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
VOLTS
TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE
PER LEG
TJ=25°C f=1.0 MHz Vsig=50mVp-p
PERES
INSTANTANEOUS REVERSE CURRENT, MICROAM-
PERCENT OF RATED PEAK REVERSE
TJ=25°C
VOLTAGE, %
JUNCTION CAPACITANCE, pF
REVERSE VOLTAGE, VOLTS
Loading...