General Semiconductor GI2404, GI2403, GI2402, GI2401 Datasheet

GI2401 THRU GI2404

0.415 (10.54) MAX.

0.154 (3.91)

0.148 (3.74)

DIA.

0.113 (2.87)

0.103 (2.62)

0.185 (4.70)

0.175 (4.44)

0.055 (1.39)

0.045 (1.14)

0.145 (3.68)

0.135 (3.43)

0.350 (8.89)

0.330 (8.38)

0.160 (4.06)

0.140 (3.56)

0.037 (0.94)

0.027 (0.68)

0.205 (5.20)

0.195 (4.95)

0.560 (14.22)

0.530 (13.46)

0.022 (0.56)

0.014 (0.35)

0.110 (2.79)

0.100 (2.54)

PIN

1

2

3

PIN 1

PIN 3

CASE

1.148 (29.16)

1.118 (28.40)

0.105 (2.67)

0.095 (2.41)

0.410 (10.41)

0.390 (9.91)

0.105 (2.67)

0.095 (2.41)

0.635 (16.13)

0.625 (15.87)

0.560 (14.22)

0.530 (13.46)

PIN 2

0.370 (9.40)

0.360 (9.14)

GLASS PASSIVATED PLASTIC RECTIFIER

Reverse Voltage - 50 to 200 Volts Forward Current - 16.0 Amperes

TO-220AB

Dimensions in inches and (millimeters)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

.

Ratings at 25°C ambient temperature unless otherwise specified.

FEATURES

♦ Plastic package has Underwriters Laboratory

Flammability Classification 94V-0

♦ Dual rectifier construction, positive centertap
♦ Glass passivated chip junctions
♦ Low power loss
♦ High surge capability
♦ Superfast recovery times for high efficiency
♦ High temperature soldering guaranteed:

250°C, 0.16" (4.06mm) from case for 10 seconds

MECHANICAL DATA

Case: JEDEC TO-220AB molded plastic body over

passivated chips
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026

Polarity: As marked
Mounting Position: Any
Mounting T orque: 5 in. - lbs. max.
Weight: 0.08 ounce, 2.24 grams

SYMBOLS GI2401 GI2402 GI2403 GI2404 UNITS

Maximum recurrent peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current

=125°C

at T

C

RRM
RMS

I

(AV)

DC

Peak forward surge current

8.3ms single half sine-wave superimposed
on rated load (JEDEC Method) at T

=125°C

C

I

FSM

Maximum instantaneous forward voltage per leg at:

IF=4A, TJ=25°C 0.975
I

=8A, TJ=25°C 0.900

F

I

=4A, TJ=100°C 0.800

F

Maximum DC reverse current T
at rated DC blocking voltage T

Maximum reverse recovery time per leg
Typical junction capacitance per leg
Typical thermal resistance per leg

(NOTE 2)

(NOTE 3)

Operating junction and storage temperature range T

NOTES:
(1) Reverse recovery test conditions:IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MH
(3) Thermal resistance from junction to case and from junction to ambient per leg mounted on heatsink

4/98

and applied reverse voltage of 4.0 Volts

Z

I

=8A, TJ=100°C

F

C
C

(NOTE1)

=25°C 50.0 5.0
=100°C

V

F

I

R

t

rr

C

J

R

ΘJA

R

ΘJC

, T

J

STG

50 100 150 200 Volts
35 70 105 140 Volts
50 100 150 200 Volts

16.0 Amps

125.0 Amps

V olts

0.895

150.0 500.0

µA

35.0 ns

85.0 pF

16.0

2.2

°C/W

-65 to +150 °C

0.1 1 10 100

10

100

1,000

0 50 100 150

0

4.0

8.0

12

16

20

110100

0

25

50

75

100

125

150

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1 .6

0.01

0.1

1

10

80

020406080100

0.01

0.1

1

10

100

RATINGS AND CHARACTERISTICS CURVES GI2401 THRU GI2404

FIG. 1 -FORWARD CURRENT DERATING CURVE

INFINITE HEAT SINK, T

C

RESISTIVE OR
INDUCTIVE LOAD

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FORWARD SURGE CURRENT PER LEG

8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)
TC=125°C

AMPERES

AMBIENT AIR RATING, T

A

AVERAGE FORWARD CURRENT,

TEMPERATURE, °C

FIG. 4 - TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS PER LEG

TJ=125°C

TJ=25°C

AMPERES

PULSE WIDTH=300µs
1% DUTY CYCLE

AMPERES

PEAK FORWARD SURGE CURRENT,

NUMBER OF CYCLES AT 60 H

Z

FIG.3 -TYPICAL REVERSE CHARACTERISTICS

PER LEG

=125°C

J

T

=100°C

J

T

MICROAMPERES

INSTANTANEOUS FORWARD CURRENT,

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS

FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG

JUNCTION CAPACITANCE, pF

REVERSE VOLTA GE, VOLTS

TJ=25°C
f=1.0 MH

Z

Vsig=50mVp-p

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %

TJ=25°C