General Semiconductor GBL04, GBL02, GBL10, GBL08, GBL06 Datasheet

...

GBL005 THRU GBL10

0.125 (3.17) x 45 degrees

Chamfer

0.080 (2.03)

0.060 (1.50)

0.095 (2.41)

0.080 (2.03)

0.825 (20.9)

0.815 (20.7)

0.050 (1.27)

0.040 (1.02)

Polarity shown on front side of case: positive lead by beveled corner

0.040 (1.02)

0.030 (0.76)

0.022 (0.56)

0.018 (0.46)

0.210

0.190

(5.3) (4.8)

0.421 (10.7)

0.411 (10.4)

0.718 (18.2)

0.682 (17.3)

0.140 (3.56)

0.128 (3.25)

Lead Depth

0.098 (2.5)

0.075 (1.9)

0.098 (2.5)

0.075 (1.9)

0.022 (0.56)

0.018 (0.46)

GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER

Reverse Voltage - 50 to 1000 Volts Forward Current - 4.0 Amperes

Case Type GBL

Dimensions in inches and (millimeters)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

FEATURES

♦ Plastic package has Underwriters Laboratory Flammability

Classification 94V-0

♦ This series is UL listed under the Recognized Component

Index, file number E54214

♦ Glass passivated chip junctions ♦ High case dielectric strength ♦ Typical IRless than 0.1µA ♦ High surge current capability ♦ Ideal for printed circuit boards ♦ High temperature soldering guaranteed:

260°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension

MECHANICAL DATA

Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750,

Method 2026

Mounting Position: Any Weight: 0.071 ounce, 2.0 grams

SYMBOLS 005 01 02 04 06 08 10 UNITS

Maximum repetitive peak reverse voltage V Maximum RMS voltage V Maximum DC blocking voltage V Maximum average forward T

rectified output current at T

=50°C

=40°C

(NOTE 1) (NOTE 2)

Peak forward surge current, single half sine-wave superimposed on rated load (JEDEC Method) T

=150°C

Rating for fusing (t<8.3ms) I Maximum instantaneous forward drop per leg

at 4.0 Amperes Maximum DC reverse current at rated T

DC blocking voltage per leg T Typical junction capacitance per leg Typical thermal resistance per leg

Operating junction storage and temperature range T

NOTES:

(1) Unit mounted on 3.0 x 3.0 x 0.11" thick (7.5 x 7.5 x 0.3cm) Al. plate (2) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length and 0.5 x 0.5" (12 x12mm) copper pads (3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts

4/98

(NOTE 3)

(NOTE 1) (NOTE 2)

=25°C 5.0

=125°C

RRM RMS

(AV)

FSM

t 93.0 A2sec

ΘJA

ΘJL

J, TSTG

GBL GBL GBL GBL GBL GBL GBL

50 100 200 400 600 800 1000 Volts 35 70 140 280 420 560 700 Volts 50 100 200 400 600 800 1000 Volts

4.0

3.0

Amps

150.0 Amps

1.1 Volts

500.0

µA

95.0 40.0 pF

22.0

3.5

°C/W

-55 to +150 °C

100

150

1.0

2.0

3.0

4.0

5.0

100

150

0.4 0.6 0.8 1.0 1.2 1.4 1.6

0.01

0.1

100

0.1

100

1,000

100

0.01

0.1

100

500

0.01

0.1

100

0.1

100

RATINGS AND CHARACTERISTICS CURVES GBL005 THRU GBL10

FIG. 1 - DERATING CURVES OUTPUT RECTIFIED

60 Hz RESISTIVE OR INDUCTIVE LOAD

AMPERES

P.C.B. MOUNTING

AVERAGE FORWARD OUTPUT CURRENT,

0.47 x 0.47” (12 x 12mm) COPPER PADS

0.375” (9.5mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD

AMBIENT TEMPERATURE, °C

FIG. 3 - TYPICAL FORWARD VOLTAGE

CHARACTERISTICS PER LEG

CURRENT

HEAT-SINK MOUNTING,

3.0 x 3.0 x 0.11” THK (7.5 x 7.5 x 0.3cm) AL. PLATE

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD

AMPERES

PEAK FORWARD SURGE CURRENT,

FIG. 4 - TYPICAL REVERSE LEAKAGE

SURGE CURRENT PER LEG

TJ = TJ max. SINGLE SINE-WAVE (JEDEC Method)

1.0 CYCLE

NUMBER OF CYCLES AT 60 Hz

CHARACTERISTICS PER LEG

50 - 400V

600 - 1000V

TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE

INSTANTANEOUS FORWARD CURRENT, AMPERES

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS

FIG. 5 - TYPICAL JUNCTION CAPACITANCE

PER LEG

TJ=25°C f=1.0 MHz Vsig=50mVp-p

MICROAMPERES

INSTANTANEOUS REVERSE CURRENT,

PERCENT OF RATED PEAK REVERSE

FIG. 6 - TYPICAL TRANSIENT THERMAL

IMPEDANCE PER LEG

°C/W

TA=125°C

TA=25°C

VOLTAGE, %

JUNCTION CAPACITANCE, pF

50 - 400V

600 - 1000V

REVERSE VOLTAGE, VOLTS

TRANSIENT THERMAL IMPEDANCE,

t, HEATING TIME, sec.