General Semiconductor FEPF6CT, FEPF6BT, FEPF6AT, FEPF6DT Datasheet

0.060 (1.52)

0.405 (10.27)

0.383 (9.72)

0.670 (17.2)

0.646 (16.4)

0.191 (4.85)

0.171 (4.35)

0.600 (15.5)

0.580 (14.5)

0.560 (14.22)

0.530 (13.46)

0.037 (0.94)

0.027 (0.69)

0.140 (3.56)

0.130 (3.30)

0.350 (8.89)

0.330 (8.38)

0.188 (4.77)

0.172 (4.36)

0.110 (2.80)

0.100 (2.54)

0.131 (3.39)

0.122 (3.08)

0.110 (2.80)

0.100 (2.54)

0.022 (0.55)

0.014 (0.36)

0.105 (2.67)

0.095 (2.41)

0.205 (5.20)

0.195 (4.95)

PIN 1

PIN 3

PIN 2

1

3

PIN

2

DIA.

DIA.

NEW PRODUCT NEW PRODUCT NEW PRODUCT

FEPF6A T THRU FEPF6DT

FAST EFFICIENT PLASTIC RECTIFIER

Reverse Volta ge - 50 to 200 Volts Forward Current - 6.0 Amperes

ITO-220AB

FEATURES

♦ Plastic package has carries Underwr iters Laboratory

Flammability Classification 94V-0

♦ Dual rectifier construction, positive center-tap
♦ Glass passivated chip junctions
♦ Superfast recovery times for high efficiency
♦ Low power loss
♦ Low forward voltage, high current capability
♦ For use in low voltage, high frequency inverters,

free wheeling and polarity protection applications

♦ High temperature soldering guaranteed:

250°C, 0.25" (6.35mm) from case for 10 seconds

MECHANICAL DATA

Case: JEDEC ITO-220AB molded plastic body over

passivated chips
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked

Dimensions in inches and (millimeters)

Mounting Position: Any
Weight: 0.08 ounce, 2.24 grams
Mounting T orque: 5 in. - lb. max.

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS FEPF6AT FEPF6BT FEPF6CT FEPF6DT UNITS

Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current

=100°C

T

C

Peak forward surge current

8.3ms single half sine-wave superimposed

I

on rated load (JEDEC Method)
Maximum instantaneous forward voltage

per leg at 3.0A
Maximum DC reverse current T

at rated DC blocking voltage T
Maximum reverse recovery time per leg
Typical ther mal resistance
Typical junction capacitance per leg
Operating junction and storage temperature range T

NOTES:

(1) Reverse recovery test conditions:IF=0.5A, Ir=1.0A, Irr=0.25A
(2) Thermal resistance from junction to case per leg mounted on heatsink
(3) Measured at 1.0 MH

(NOTE 2)

and applied reverse voltage of 4.0 Volts

Z

=25°C 5.0

A

=100°C

A

(NOTE 1)

R

(NOTE 3)

J, TSTG

RRM

RMS

I

(AV)

FSM

V

I
t

C

DC

F

R

rr
ΘJC

J

50 100 150 200 Volts
35 70 105 140 Volts

50 100 150 200 Volts

6.0 Amps

100.0 Amps

0.975 Volts

50.0

µA

35.0 ns

5.4 °C/W

28.0 pF

-55 to +150 °C

4/98

0

50

100

150

0

2.0

4.0

6.0

8.0

10

1

10

100

0

25

50

75

100

125

150

0.1

1

10

0

10

20

30

40

50

60

0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

0.1

1

10

40

100

0

20

40

60

80

100

0.01

0.1

1

10

100

RATINGS AND CHARACTERISTICS CURVES FEPF6AT THRU FEPF6DT

AVERAGE FORWARD CURRENT,

FIG. 1 - FORWARD CURRENT DERATING CURVE

RESISTIVE OR INDUCTIVE LOAD

AMPERES

CASE TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS PER LEG

TJ=125°C

PEAK FORWARD SURGE CURRENT,

AMPERES

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FORWARD SURGE CURRENT

TC=100°C

8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)

NUMBER OF CYCLES AT 60 H

FIG. 4 - TYPICAL REVERSE CHARACTERISTICS

PER LEG

Z

AMPERES

TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE

INSTANTANEOUS FORWARD CURRENT,

INSTANTANEOUS FORWARD VOLTAGE,

FIG. 5 - TYPICAL JUNCTION

CAPACITANCE PER LEG

VOLTS

TJ=25°C
f=1.0 MH
Vsig=50mVp-p

TJ=125°C

TJ=100°C

MICROAMPERES

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

TJ=25°C

Z

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %

JUNCTION CAPACITANCE, pF

REVERSE VOLTAGE, VOLTS