General Semiconductor FEP30JP, FEP30GP, FEP30HP, FEP30DP, FEP30FP Datasheet

FEP30AP THRU FEP30JP

PIN 1

PIN 3

CASE

0.245 (6.2)

0.225 (5.7)

0.645 (16.4)

0.625 (15.9)

0.323 (8.2)

0.313 (7.9)

0.142 (3.6)

0.138 (3.5)

0.170
(4.3)

0.086 (2.18)

0.076 (1.93)

0.160 (4.1)

0.140 (3.5)

0.225 (5.7)

0.205 (5.2)

0.127 (3.22)

0.117 (2.97)

0.048 (1.22)

0.044 (1.12)

0.795 (20.2)

0.775 (19.6)

0.840 (21.3)

0.820 (20.8)

1

2

3

0.078 REF
(1.98)

0.203 (5.16)

0.193 (4.90)

10

o

TYP.

BOTH SIDES

30

o

10

o

1o REF.

0.118 (3.0)

0.108 (2.7)

0.030 (0.76)

0.020 (0.51)

BOTH SIDES

PIN 2

FAST EFFICIENT PLASTIC RECTIFIER

Reverse Voltage - 50 to 600 Volts Forward Current - 30.0 Amperes

TO-247AD

♦ Plastic package has Underwriters Laboratory

FEATURES

Flammability Classification 94V-0

♦ Dual rectifier construction, positive center-tap
♦ Glass passivated chip junctions
♦ Superfast recover y times for high efficiency
♦ Low forward voltage,

high current capability

♦ Low thermal resistance
♦ Low power loss
♦ High temperature soldering guaranteed:

250°C, 0.16” (4.06mm) from case for 10 seconds

MECHANICAL DATA

Case: JEDEC TO-247AD molded plastic body over

passivated chips
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026

Polarity: As marked
Mounting Position: Any

Dimensions in inches and (millimeters)

Mounting T orque: 10 in. - lbs. max.
Weight: 0.22 ounce, 6.3 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current

=100°C

at T

C

Peak forward surge current

8.3ms single half sine-wave superimposed I
on rated load (JEDEC Method) at T

=100°C

C

Maximum instantaneous forward voltage per leg
at 15.0A

Maximum DC reverse current T
at rated DC blocking voltage T

Maximum reverse recovery time time
per leg

Typical junction capacitance per leg
Typical thermal resistance

Operating storage and temperature range T

NOTES:

1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MH
(3) Thermal resistance from junction to case per leg mounted on heatsink

4/98

=25°C 10.0

C

=100°C

C

(NOTE 1)

(NOTE 2

) C

)R

(NOTE 3

and applied reverse voltage of 4.0 Volts

Z

SYMBOLS 30AP 30BP 30CP 30DP 30FP 30GP 30HP 30JP UNITS

FEP FEP FEP FEP FEP FEP FEP FEP

50 100 150 200 300 400 500 600 Volts
35 70 105 140 210 280 350 420 Volts
50 100 150 200 300 400 500 600 Volts

30.0 Amps

300.0 Amps

F

0.95 1.3 1.5 Volts

500.0

35.0 50.0 ns

J

175.0 145.0 pF

1.0 °C/W

STG

-55 to +150 °C

µA

I

(AV)

FSM

, T

J

RRM

RMS

DC

V

I

R

t

rr

ΘJC

RATINGS AND CHARACTERISTIC CURVES FEP30AP THRU FEP30JP

0 50 100 150

0

6.0

12

24

30

36

110100

0

50

100

150

200

250

300

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

1

0.1

10

40

0.1 1 10 100

10

100

1,000

020406080100

0.1

1

10

100

1,000

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FIG. 1 - FORWARD CURRENT DERATING CURVE

RESISTIVE OR INDUCTIVE LOAD

FORWARD SURGE CURRENT PER LEG

TC=100°C

8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)

AMPERES

AVERAGE FORWARD CURRENT,

CASE TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS PER LEG

PULSE WIDTH=300µs
1% DUTY CYCLE

TJ=125°C

AMPERES

INSTANTANEOUS FORWARD CURRENT,

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS

TJ=25°C

50-200V

300-400V
500-600V

AMPERES

PEAK FORWARD SURGE CURRENT,

NUMBER OF CYCLES AT 60 H

Z

FIG. 4 - TYPICAL REVERSE CHARACTERISTICS

PER LEG

=25°C

J

MICROAMPERES

T

=100°C

J

T

50-200V

300-600V

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

=25°C

J

T

FIG. 5 - TYPICAL JUNCTION CAPACITANCE

JUNCTION CAPACITANCE, pF

50-400V

500-600V

REVERSE VOLT AGE, VOL TS

TJ=25°C
f=1.0 MH

Z

Vsig=50mVp-p

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %