General Semiconductor FEP16HT, FEP16GT, FEP16FT, FEP16DT, FEP16CT Datasheet

FEP16A T THRU FEP16JT

0.415 (10.54) MAX.

0.154 (3.91)

0.148 (3.74)

DIA.

0.113 (2.87)

0.103 (2.62)

0.185 (4.70)

0.175 (4.44)

0.055 (1.39)

0.045 (1.14)

0.145 (3.68)

0.135 (3.43)

0.350 (8.89)

0.330 (8.38)

0.160 (4.06)

0.140 (3.56)

0.037 (0.94)

0.027 (0.68)

0.205 (5.20)

0.195 (4.95)

0.560 (14.22)

0.530 (13.46)

0.022 (0.56)

0.014 (0.35)

0.110 (2.79)

0.100 (2.54)

PIN

1

2

3

PIN 1

PIN 3

CASE

1.148 (29.16)

1.118 (28.40)

0.105 (2.67)

0.095 (2.41)

0.410 (10.41)

0.390 (9.91)

0.105 (2.67)

0.095 (2.41)

0.635 (16.13)

0.625 (15.87)

0.560 (14.22)

0.530 (13.46)

PIN 2

0.370 (9.40)

0.360 (9.14)

FAST EFFICIENT PLASTIC RECTIFIER

Reverse Volta ge - 50 to 600 Volts Forward Current - 16.0 Amperes

TO-220AB

FEATURES

♦ Plastic package has Underwriters Laboratory

Flammability Classification 94V-0

♦ Dual rectifier construction, positive centertap
♦ Glass passivated chip junctions
♦ Low power loss
♦ Low forward voltage, high current capability
♦ High surge current capability
♦ Superfast recovery times for high efficiency
♦ High temperature soldering guaranteed:

250°C, 0.16" (4.06mm) from case for 10 seconds

MECHANICAL DATA

Case: JEDEC TO-220AB molded plastic body over

passivated chips
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026

Polarity: As marked
Mounting Position: Any
Mounting T orque: 5 in. - lbs. max.

Dimensions are in inches and (millimeters)

Weight: 0.08 ounce, 2.24 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS 16AT 16BT 16CT 16DT 16FT 16GT 16HT 16JT UNITS

Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current

=100°C

at T

C

RRM
RMS

DC

I

(AV)

Peak forward surge current

8.3ms single half sine-wave superimposed

I

FSM

on rated load (JEDEC Method)
Maximum instantaneous forward voltage per leg

at 8.0A
Maximum DC reverse current T

at rated DC blocking voltage per leg T
Maximum reverse recovery time

per leg
Typical
Typical ther mal resistance

Operating junction and storage temperature range T

NOTES:

(1) Reverse recovery test conditions:IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MH
(3) Thermal resistance from junction to ambient and from junction to case per leg mounted on heatsink

unction Capacitance per leg

J

4/98

and applied reverse voltage of 4.0 Volts

Z

(NOTE 3)

(NOTE 1)

(NOTE 2)

=25°C 10.0

C

=100°C

C

V

F

I

R

t

rr

C

J

R

ΘJA

R

ΘJC

J, TSTG

FEP FEP FEP FEP FEP FEP FEP FEP

50 100 150 200 300 400 500 600 Volts
35 70 105 140 210 280 350 420 Volts
50 100 150 200 300 400 500 600 Volts

16.0 Amps

200.0 Amps

0.95 1.3 1.5 Volts

500.0

µA

35.0 50.0 ns

85.0 60.0 pF

15.0

2.2

°C/W

-55 to +150 °C

RATINGS AND CHARACTERISTICS CURVES FEP16AT THRU FEP16JT

0 50 100 150

0

4.0

8.0

12

16

20

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0

0.1

1

10

40

0.1 1 10 100

10

100

1,000

0 20406080100

0.01

0.1

1

10

100

1 10 100

0

50

100

150

200

250

300

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FIG. 1 - FORWARD CURRENT DERATING CURVE

RESISTIVE OR INDUCTIVE LOAD

FORWARD SURGE CURRENT

8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)

AMPERES

AVERAGE FORWARD CURRENT,

CASE TEMPERATURE, °C

FIG. 3- TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS PER LEG

TJ=125°C

PULSE WIDTH=300µs
1% DUTY CYCLE

TJ=25°C

AMPERES

INSTANTANEOUS FORWARD CURRENT,

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS

50-400V
300-400V
500-600V

AMPERES

PEAK FORWARD SURGE CURRENT,

NUMBER OF CYCLES AT 60 H

FIG. 4 -TYPICAL REVERSE CHARACTERISTICS

PER LEG

50-400V

500-600V

=125°C

J

T

=100°C

J

T

MICROAMPERES

Z

FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG

JUNCTION CAPACITANCE, pF

50-400V

500-600V

REVERSE VOLTAGE, VOLTS

TJ=125°C
f=1.0 MH

Z

Vsig=50mVp-p

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

TJ=25°C

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %