General mobile DST BUSINESS User Manual

Download

Table of Contents

1.For your Safety……………………….………………….4

2.Mobile Phone Profile……………………..…………….9

3.Preparation before Use……………………………….13

4.General Instructions for Mobile Phone…...............23

5.Basic operation………………………………………...39

6.UseMenuFunctions …………………………………...47

7. English Editor Operation ……… ……………….142

8.Use USB……………………………………………..145

9.Appendix Ⅰ………………………………………….146

10.Appendix Ⅱ……………………….……………….152

11.Appendix Ⅲ……………………………………….154

12.SAR …………………………………………..……157

1.For your Safety

For your safety and proper use of the mobile phone, please

read the f ollowing guidelines carefully: Do not switch the

mobile phone on when close to chemical factory, gas station

or other explosive objects.  During driving, please use headset for safety purpose;

unless otherwise in emergency, always stop the car on

roadside to have a call conversation.

 Because the use of the mobile phone can cause

interference in the aircraft, never use the mobile

phone in aircraft. The use of the mobile phone is

dangerous and illegal; do switch off the mobile phone

before boarding.

 Pay special attention to the use of the mobile phone

near heart pacemaker, deaf-aid and some other

medical equipments, because the mobile phone can

cause interference with them.

 None-original f actory’s accessories and parts will lose

guarantee.

 Do not dismantle the mobile phone without permission.

In case of failure, please contract the supplier as soon

as possible.

 Do not plug the charger into the mobile phone and

charge without battery. Always power off the mobile

phone when taking out the battery; otherwise the

memory of the phone may be damaged.

 When charging the mobile phone, always keep it in

the place with good ventilation, heat sink and away

from flammable and explosive objects.

 In order to avoid demagnetization, always keep the

mobile phone away from magnetic objects such as CD,

credit card etc.

 Ensure the mobile phone not to contact any liquid;

once such case occurs, remove the battery and

contact the supplier immediately.

 Do not use the mobile phone in the environment at too

high or too low temperature, never expose the mobile

phone under strong sunshine or too wet environment.

The suitable temperature for the phone and

accessories is 0℃-40℃. The height to use the phone

shall be less than 2,000m.

 Do not use liquid or wet cloth with strong cleanser to

clean the mobile phone.

 This mobile phone has s hooting, videoing and audio

recording functions, which shall be used as per the

related laws and regulations.

 Always keep the mobile phone out of children’s reach.

Do not throw or vibrate the mobile phone because

violent treatment to the mobile phone may damage

the inner circuits and precise structures.

 Please do not discard the waste battery into general

household garbage. Please deal with the waste

battery according to provisions where they are

definitely made.

Warning: We will not be bear any responsibility for any

incompliance with the above guidelines or improper use of

the mobile phone.

Our company keeps the right to make modifications to any

of the content here in this user guide without public

announcement in advance.

The content of this manual may vary from the actual

content displayed in the mobile phone. In such case, the

latter shall govern.

2.Mobile Phone Profile

The mobile phone has a standard keypad, a single

screen. In addition, it is inbuilt with one vibration motor, one

charger/data common transmission port and one exterior

memory card (T-Flash card) port.

(Below is the front of the mobile phone)

Left soft key

Receiver

Screen

Send/Dail key

Number key

OK key

Right soft key

End key

(Below is the side of the mobile phone)

USB port

(Below is the back of the mobile phone)

Speaker

Locker

Camera

Battery Cover

3.Preparation before Use

Battery Cover

Battery

T-flash card

Sim 2

Sim 1

Install SIM Card

When registering mobile phone number, you can apply

for two different phone numbers, two different mobile phone

network service providers and thus obtain two SIM

(Subscriber Identification Module) cards.

With these two SIM cards, you can use all functions of

your mobile phone. The SIM cards save the parameters

needed for communications and personal data, including

PIN (Personal Identification Number) code, phonebook,

short message and other extra system services. Warning: Do not distort or scratch the SIM card nor let it contact static, dust or moisture. If it is lost, please contact immediately your network operator for help.

Before SIM card installation, please switch off the mobile

phone. The SIM card is installed on the back of the mobile

phone.

Follow the following diagram to install the SIM card.

Please insert the host SIM card into the SIM1 slot and the

slave SIM card into the SIM2 slot.

Note: If SIM card is inserted only into the SIM1 slot,

then only the host works; likely, If SIM card is inserted only

into the SIM2 slot, then only the slave works. When two SIM

cards are inserted into the SIM1 slot and SIM2 slot

respectively, you can choose work mode freely as you wish.

Note: As the SIM card is small object, keep it out of

children’s touch or prevent children gulping it!

Install Memory card

As the mobile phone does not have enough storage

space, to use some functions, you need to install a memory

card (This mobile phone use T-FLASH card.)

SIM card

Install T-FLASH card: Open the back c over to take out the battery, release the T-Flash card lock, insert the T-Flash card into its slot, restore the lock and the battery before restarting the mobile phone. Note: As the T-FLASH card is small object, keep it out of children’s touch or prevent children gulping it!

Install Battery

The mobile phone is suitable for original battery and accessories. When the battery is idle, it is recommended to put it into the protection box.

Note: Do install the battery as per the diagram so as prevent the battery contact patch being damaged.

Charge Battery

The new battery cannot reach the optimal efficiency unless it has undergone several continuous complete charges and discharges.

When the battery is used up, charge it in time. Over-discharge can damage the battery.

After the battery is charged full, cut off the connection of charger with the AC power supply and then the connection with the mobile phone.

During charging, the battery capacity icon on the screen

flickers from the right to the left. After the battery is charged

full, the icon is full of bars. Slight heat during charging is

normal. Warning: When a travel charger and its accessories are used to charge the battery, please firstly check if they are

original or recognized by the original manufacturer. The use of other accessories may damage your mobile phone and cause risks! Always use them indoor and dry places.

Notices on using the battery

The performance of the battery is affected by many factors, including radio barrier network settings, signal strength, signal strength, work temperature, chosen and used functions or settings as well as phone accessories, tone, data or other applications.

For optimal performances, please follow the rules below:  New battery or the battery having been idle for long

need charging for long. The standard voltage scope for the battery is 3.6V-4.2V.

 During charging, keep the battery at room temperature

or similar temperature.

 With time passing by, the battery will gradually be

worn and thus need longer time to charge. This is normal. However, after normal charging, if call duration decreases but charging time increases, you need to buy another battery from the original manufacturer or authorized by the original manufacturer. The battery of interior quality can damage your mobile phone and cause danger!

 If the phone is overused at low battery when charging,

there might need a longer time for the charge indicator to be shown on the screen.

Note: Please dispose the battery according to the local regulations. Try to recycle the battery as possible. Do not treat the waste battery as common waste. Warning: Do not throw the battery into fire so as to prevent fire. The broken battery may cause explosion.

Warning

Charging the mobile phone by improper means can c ause to explosion. Always refer to the related regulations f or the disposal of the battery.

PIN code

PIN1 Code:It is the personal identification number used to enter SIM and able to prevent others using SIM1 without permission. If the mobile phone has activated the PIN1 code protection, when the mobile phone is switched on, the screen will display “Input PIN”. In the process of inputting PIN1 code, the screen will use “*” to represent the input content. While obtaining SIM, you can obtain its PIN1 code.

PIN2 Code: It is the personal identific ation number used

for some special functions such as paid call etc. PUK Code and PUK2 Code(8-digit)

To change the locked PIN code, you need to use PUK (Personal Unblocking Key) code. To change the locked PIN2 code, you need to use PUK2 code. If these two codes are not provided together with the SIM cards, ask the local service provider for them. Warning: If the PIN code is input wrongly for successively three times, the SIM card will be locked. Please contact the network operator immediately for help. Attempt to unlock the code may make the SIM card ineffective forever!

4.General Instructions for Mobile Phone

Dial key

It is used to dial a call (with phone number entered or in

phonebook state) or receive an incoming call. In standby

state, press this key to display the latest call register (SIM1

and SIM2 support respectively 20 call entries, including

received c alls, missed calls and dialed calls). In dual-SIM

standby mode, press this key to have an option menu on

which you can choose to operate via SIM1 or via SIM2.

Switch-on/off key /End key

In call state, it is used to interrupt a call; in call conversation state, it is used to end a call or exit from the

current menu and back to the standby state. Hold this key for 4~5s to switch on/off the mobile phone.

Left/Right soft key

Press the left/right soft key to have the functions indicated in the bottom row of the main screen of the mobile phone.

Functional direction key

This mobile phone has four direction keys, with the left, right, up and down control functions. In some interfaces, they have special function, for example, in call state, press the up/down key to adjust volume. Similarly, these four direction keys can be set with shortcut functions, in default state: press the up key to enter the music player, the down key to enter the alarm clock, the left key to set rings and the right key to enter profiles. Shortcut keys can be active only in standby state and their function definitions can be set by yourself with the procedures as: enter the phone settings

menu, choose dedicated key function to reedit the direction keys. You can find detail information about navigation keys below table.

Press

Keys

Navigati

on Key

Long/

Shortly

Long

Short

Standby

State

Default

entering

music

player

Default

entering

music

player

Audio

Player

MP3 play

/ pause

MP3 play

/ pause

FM Radio

Manual

Automatic Search

On/Off

Manual

Automatic Search

On/Off

Incoming

Call

Call State

Turn up

call

volume

Turn up

call

volume

Down

Navigati

on Key

Left

Navigati

on Key

Right

Navigati

on Key

Long

Short

Long

Short

Long

Default

entering

alarm

Default

entering

alarm

Default

entering

user

profiles

Default

entering

user

profiles

Default

entering

tone setup

MP3 stop Radio On/ Off

MP3

rewind

MP3 fast

forward

Backward search

title

Forward search

Eliminate

incoming

call tone

Eliminate

incoming

call tone

Turn

down call

volume

Turn

down call

volume

Default

Short

entering

tone setup

* Key Short

# Key Short

OK Key Short

Next title Forward search

MP3

volume

down

MP3

volume

Radio record on

Radio volume

down

Radio volume up

Standard keypad

On the keypad, you can s ee 0-9 number keys, * key

and # key, totally 12 keys.

Press these keys to input phone number, password,

English letters, symbols etc, or choose menus.

Note: In standby state, hold “1” key long to call the voice inbox service center. The number for the voice inbox should be preset.

In different states or different functional menus, * key and # key have different functions:

 Press “#” key long to start or exit from the s ilence

mode.

 Continuously press shortly or press long * key to input

“P”, "＋" or "W" , among which, “P” and “W” are used for extension calls while “+” for international calls.

 In music player state, * and # are used to adjust

volume. Tip: The difference between “W” and “P” is that “P” will directly send DTMF after 3s pause while “W ” will eject a window asking whether the user to send DTMF. FM radio function key

 OK key: Activate radio recording.

 Up key: Switch between search or fine tuning.  Down key: In radio state, press the key to turn on/off

radio.

 Left/Right key: In s earch state, press the left/right key

to search channels forward and backward until you

find an effective channel. In fine tuning state, you can

have a tuning of 0.1MHz downward or backward.

 1-9 number keys: If they are pressed shortly, you can

switch to the corresponding channels saved in the

channel list; if they are pressed long, you can save the

current frequency to the corresponding channel.

 *, # key: Adjust volume.

Keypad lock

When in standby interface, if the mobile phone is idle for certain time, it will be locked automatically. Press the right soft key to release and press the left soft key again to unlock.

After the mobile phone is locked, the keypad cannot be activated easily; in case of incoming call, likewise, press the answer key to receive it; after that, the keypad will be locked automatically.

Icons in Standby State

Line 1 signal antenna

Line 2 signal antenna

Activate the alarm clock

SIM 1 SMS

SIM 2 SMS

Ring; this icon may vary with different warning modes

and it may be in the three icons:

Ring after vibration

Vibration and ring

Vibration

Missed calls

unLocked

Master line1

Slave line1

Master line2

Slave line2

MMS BUSY

MMS unread

SIM1 All calls diverted

SIM2 All calls diverted

Locked

SIM1 E-mail

SIM2 E-mail

SIM GPRS

Continuous display indicates the Bluetooth function has

been activated and can be searched; flicking indicates data

are under transmission.

Bluetooth function has been activated and can be

searched

disconnected

Language and Input M ode

The mobile phone has defaulted English input mode. For different areas, there are different languages and corresponding input modes.

Call hint

The mobile phone is inbuilt with vibration motor and buzzer and provides several incoming call modes:

Ring

Vibration

Ring after vibration

Vibration and ring

Services

Services are provided with SIM kit. The mobile phone support service function. The detailed menu items depend on SIM card and the network. When the network provides such function and your SIM card supports such function, the service menu will automatically be posted in the services of the mobile phone.

Callers’ group

The callers’ group in the mobile phone includes friends, family, VIP, business and others etc. You c an set different call tone and photo f or different callers’ group.

Term Description Dial domestic calls

 The simplest method to dial a domestic call is to input

phone number via the number keypad, then press dial

key to dial call. To change phone number, press “C key”. During dialing, the screen will display a cartoon. If SIM card 1 call, "SIM1-" occurs; if SIM card 2 call, "SIM2-" occurs. When the other party is connected, the screen will display the corresponding information.

 Press end key to end the call.  To dial a domestic call, input area code + phone

number and then press the dial key.

Dial international calls

 If you want to make an international call, you can

press * key continuously until the international dialing prefix “+” is seen on the screen. This will allow you make an international call from any country without knowing the dialing prefix.

 After inputting the prefix, you need to input the

Country number and complete telephone number. You can input the Country number according to the

common practice, such as, 49 f or Germany, 44 for British, 46 for Sweden, etc.

 Dial international telephone number as following: “+”

Country number +Complete telephone number + Dial key.

Dial fixed-line telephone extension

 Some fixed-line telephone extension may not directly

get through, so you need to connect to the switchboard at first then put through extension number. The mobile phone can automatically dial extension number if you input “P” between the s witchboard and extension number. Method for input “P” as f ollowing: hold press or c ontinually short press three times “*” key (“P” will be shown on the display).

 Dial fixed-line telephone extension as following: phone

number + “P” + extension number + dialing key

Emergency calls

If your phone is under the network coverage (you can know this by checking the signal bar at the up left corner on the screen), you can make emergency calls. If your network supplier does not provide roaming service in this area, Emergency will be shown on the screen. That means you can only make this kind of calls. If your phone is under the network coverage, you can even make emergency calls without the SIM card. * In some areas, 112 (emergency call) service is provided by the network operator. In case of failure, consult the network operator.

IMEI

International Mobile Equipment Identity number. Switch off the mobile phone and take off the battery, then you will see the label with such number on the back of the mobile phone. Also, this number is saved in the mobile phone. After switch-on, in standby state, input “*#06#” to

display it.

IP dial

Firstly, in Settings/Call Settings, set correct IP access number. Enter the phonebook and choose IP Dial.

Note: Regarding whether to activate IP dial when dialing local call, please consult the network operator.

5.Basic operation

Switch on

Press the s witch-on/off key to start the mobile phone,

then the screen will display switch-on image. Then you can

enter Settings menu to set phone modes, including SIM1 &

SIM2 On, Only SIM1 On, Only SIM2 On and Flight. The

defaulted one is Only SIM1 On.

After insert SIM card, the mobile phone will automatically

check the SIM card availability, and then it will be shown

information as following on the display by sequence:

1. “Input phone password”——If you have set the

password.

2. “Input PIN” —— If you set SIM card password.

3. “No service”—Indicates fail to make register and cannot

make any calls.

4. “Emergency calls only”—indicates has registered to

other network and only can make call to 112.

5. “Searching”—the mobile phone is searching network

until find appropriate network;

6. “Operator name”—Indicates network successfully

registered.

Note: If you do not know PIN c ode, please contact the

network service provider.

The defaulted phone password “1122”

Switch off

To switch off the mobile phone, press the end key.

When the screen displays switch-off cartoon, the host and

the slave will be off at the same time. Do not take out the

battery to switch off the mobile phone. If so, the SIM card

can be damaged easily and some data will be lost.

Dial a Call

 With the number keypad, you can enter phone

numbers (if wrong characters are input, press the

clear key to delete them). Press the dial key to dial the

phone number. In SIM1 and SIM2 On state, you can

choose to dial a call via SIM1 or SIM2. To end a call,

press the end key; or to cancel a dial, press the

Cancel key or the switch-on/off key. After the c all is

connected, you can see the call timer on the screen.

 Dial a call via phonebook: Enter the phonebook and

search the desired name/phone number, and then

press dial key to dial call.

 Redial latest dialed number: In standby state, press

dial key to view the list of the latest dialed 20 phone

number or names. Roll to the desired phone number

or name and press dial key to dial call.

Adjust Receiver Volume

In call conversation, press the upper direction key or lower

direction key to adjust the volume of the receiver.

Answer a Call

When there is a call, as per the settings of the mobile

phone, you will be alerted with ring, vibration, vibration and

ring as well as vibration then ring.

To receive a call, press Dial/Call Key.

To refuse a call, press Switch-on/off key or the end key

directly.

If the CLI (Call Line Identity) is opened, the phone

number of the caller will occur on the screen. If this number

has been saved in the phonebook, the name corresponding

to this number will be displayed on the screen.

Send DTMF Signal

When this function is s et, in call conversation, press the

desired number key and * key and # key to s end DTMF

signals to the other party. If such function is inactive, then

extension call will become impossible.

Dial Hold

If you have applied for dial hold, in the call conversation

process, press “Options” to have the following function

menus:  Hold: Hold the current call but with the line keeping

connected.

 End: End the current call conversation.  New Call: Enter the dial interface, dial another call.  Phonebook: Enter the directory of the phonebook.  Messages: Enter the directory of theSMS.  Sound recorder: While having call conversation, you can

record the call.

 Background sound: You can choose call background

music. After activating and choosing the desired

background music, both parties can listen to the

activated background music.

 Mute: Set mute on, the MIC will be inactive. Set off to

return the normall call conversation.

 DTMF: You can set whether to send DTMF signals.

Note: Some menu items need the support of the local

network or can occur in special cases, such as Conf erence

and New Call. Consult the local network operator for details.

Fast Read SMS

When the user receives unread SMS, the screen will

display an icon of unread SMS. Press Read to enter and

read the SMS. The SIM card 1 unread SMS icon is marked

with “1” and SIM card 2 unread SMS icon is marked with “2”.

Missed Calls

When there is a missed call incoming, the screen will

display a missed call icon. And press Read to enter and read

missed calls.

Connect to Voice mail

The mobile phone allows connecting the incoming call

into the voice mail and then you can receive a notice about

voice message. (The voice mail number must be preset).

Note: Voice mail needs the support of the local network.

6.Use Menu Functions

6.1 Messages

[SMS ]

SMS is a kind of network service that cannot be used to

send and receive short messages until you apply to the

network operator

Both SIM cards of the mobile phone can send and

receive SMS. The SMS is sent to the SMS center of the

network and then sent by the network to the target user

(GSM user). If the user does not switch on the mobile phone

or the mobile phone cannot receive the SMS (the memory is

full), the network will save the SMS temporarily. The

duration of storage depends on sender’s settings and

network service provider.

With this function, the mobile phone can send and

receive chain text messages, which may affect the message

fees. For more information, please consult the service

provider.

When the SMS capacity is full, there will be an SMS

icon flickering on the standby interface. The full capacity can

affect SMS reception. Delete some SMS to solve the

problem.

If the other party has received SMS, you will hear the

alert s ound from the mobile phone (if such alert function is

set as ON)

Note: When sending SMS via the SMS network, the mobile

phone may display “Message sent”. It indicates that the

SMS has been s ent to the SMS center inbox set in the

mobile phone but does not mean the receiver has received

the SMS. For more information, please consult the service

provider.

Write Message

You can write message in this menu.

Every SMS can contain about 640 world length English

characters; To write SMS, press “#” key to switch input

modes, “*” key to select Symbol; press “Clear key” to clear

one character before the cursor, long press “Clear key” to

delete all characters; press the end key to back to the

standby interface, press the up and down direction key to

choose characters, press “select” key to confirm.

The mobile phone can send the chain SMS more than .

characters (limit for common text messages). If the

SMS contains more than 140 English characters, then the

SMS will be split into 2pcs or more. You can insert images,

cartoons, rings etc into SMS. However, the SMS will not be

received and displayed unless the network and the receiving

mobile phone support.

You can enter the phone number or choose a number

from the phonebook to send the SMS. In dual-SIM standby

mode, you can choose to send the SMS via SIM1or SIM2.

Inbox

You can see the SMS in the inbox.

 Reply: You can reply to the received SMS.  Delete: Delete the current SMS.  Forward: You can edit the current SMS or send it after

editing.

 Copy to Phone: You can copy the entries in SIM card

onto the phone.

 Move to Phone: You c an move the entries in SIM card

onto the phone.

 Delete All: You can delete all SMS in inbox.  Copy all: You can have two options, i.e. copy all entries

on the SIM card in the inbox onto the phone or vice

versa.

 Move all: You can have two options, i.e. move all entries

on the SIM card in the inbox onto the phone or vice

versa.

 Use Number: You can extract the number in the SMS

and save it or dial a call.

 Use URL: You can link to the website contained in the

received SMS.

 Use Email address: You can extract the email address

and save it to phonebook.

 Chat:select chat room,and set remote number to chat. 

Outbox

While s ending SMS, if choosing “Save and Send”, you

can save the SMS into the Outbox. You can directly save the

edited SMS into the Outbox, in such c ase, the Outbox will

display “No number”, i.e. no target number. If you fail to send

the SMS, it will be saved in the Outbox. Also, you c an have

such operations as send from SIM1, send from SIM1,

edit,delete,copy to phone move to phone,delete all,copy

all,move all,use number and use URL.

Templates

With it, you can pre-edit some common phrases, which is

convenient for quick SMS editing.

Message Settings

You can set some parameters of the SIM1 SMS or SIM2

SMS in the menu.

 Profile Setting: To s end SMS, you must input the

SMS center number.

Note: The SMS center number is provided by the network

operator.

 Common Setting

 Delivery Report: The network will inform you

whether the other party has received the SMS

and what the time is.

 Reply Path: You can send the reply path to the

network terminal. This function needs the

support from the SMS center.

 Memory Status: You c an view the capacity of the

SIM card or the phone for SMS.

 Preferred Storage: You can set the storage position

(SIM or phone) for SMS.

[MMS ]

MMS can contain words, sound and photos. If the MMS

is out of the limit, the mobile phone will be unable to receive

the MMS. If the MMS contains photos, the mobile phone will

adjust photos so as to display them on the screen

completely.

The display effect of MMS depends on reception

devices.

Note: You cannot use photo messages unless the network

operator or service provider supports to do so. You cannot

receive and display MMS unless the mobile phone has the

compatible MMS or e-mail function.

Write Message

Receiver

Add Number-- Input the number of the receiver.

Add E-mail-- Input the e-mail of the receiver.

Copy

 Add Number-- Input the number of the receiver.  Add E-mail-- Input the e-mail of the receiver.

Secret copy

 Add Number-- Input the number of the receiver.

 Add E-mail-- Input the e-mail of the receiver.

Subject: You can edit the subject of the MMS Edit Content

After the MMS is edited, press the OK key to have the

following options:

 Done: Finish the editing of the current MMS.  Input Method: You can choose the desired input

method.

 Add Picture: You can insert your desired

Picture.

 Add Audio: You can insert your desired audio.  Add Video: You can insert your desired video.  Add attachment:You c an insert your desired

annex

 Add slide before:You can add new page before

 Add slide after: You can add new page after  Add bookmark text:You can insert your

bookmark

 Preview: You can preview the editing effect of

the MMS.

 Slide timeing: You can set the play time of the

current page MMS.

Inbox

You can see the MMS in the inbox and have the following

operations:  view: You can view the MMS and s ave photos, audio

and annex.

 Reply: Reply the sender with MMS.

 Reply by SMS: Reply the sender with SMS  Reply All: If the MMS you receive has been sent to many

receivers by the sender, with such function, you can

send a reply MMS to the same receivers.

 Forward: You can directly forward this MMS to others.  Delete: Delete the current MMS.  Delete All: You can delete all MMS in inbox.  Save as template:take a new mms as a template  Properties:the details of the new mms including

subject,date and file size.

 Use details: View the detailed information of the current

message.

Outbox

You can view the MMS send and saved in the Outbox

and failed and have such operations as view,

send,delete,delete all,save as template,properties,use

details.

Drafts

You can save the edited MMS into the drafts, and also

you can have such operations as view,

send,edit,delete,delete all,save as template,properties,use

details on the MMS in the drafts.

Template

There are 5pcs preset MMS in the mobile phone and

you can have such operations as View, Details and write

message,properties from Template.

MMS Settings: You can set some parameters of the MMS in

the menu.

compose:

 creation Mode-- "restricted" and “free ".  picture resizing-- You can reduce the size of the

inserted photo,including:160*120,320*240 and

Off.

 Automatic Signature-- You can on/off such

function.

 You can edit the content of the automatic

signature.

Sending Settings:

 validity Period-- You can set the time to save in

the MMS service center and send, including 1h,

6h,12h, 1d, 1w and Max.

 delivery report--You can on/off such function.

 Read Report- You can on/off such function.  Priority-- Including Normal, High and low.  Slide timing-- The time space when the other

side read the MMS.Default is five seconds. Max

sliding timing: 60 seconds.

 delivery timing-- Immediately、in one hour、in

twelve hours、in 24 hours.

retrieve:

 Home Network-- Delayed, immediate and

rejected.

 Roaming -- The same as to the main network,

including as home, Delayed and rejected

 Read Report—on request,Send, never Send  delivery Report-- on and off.

Filter:

 Anonymous-- Allow and reject  Advertisement—Allow and reject.

Server Settings: In dual-SIM mode, you can separately set

SIM1 and SIM2. After choosing Settings, you c an have the

following settings:

 Activate profile  Edit profile

 Rename profile-- Set name.  Homepage-- The website for editing MMS

( e.g. http://mmsc.monternet.com)。

 Data account  connection Type--WAP, HTTP.  User Name-- You can edit the name of the

user.

 Password-- You can set password.

Memory Status:

You can see the utilization rate of the mobile phone,

including the used space and the free space.

[Chat]

In standby, choose [Menu/Info/Chat] to enter Chat Room 1

and Chat Room 2 to have a chat.

[E-Mail]

Before use, you need to set the e-mail in the “E-mail

accounts” menu. Via this menu, you c an receive and send

e-mail.

 Send and Receive: You can send/receive the e-mail

from the specified mailbox.

 Write E-mail: You can edit e-mails.

 Inbox: You can see the received e-mails.

 Outbox: You can see the sent e-mails.

 Sent: You can See the backup of the sent e-mails.

 Drafts: You can see the drafts in the specified mailbox.

 Clear mailbox: You can clear the e-mails in the

specified mailbox, including inbox, outbox, sent e-mail

backup and drafts, or clear all e-mails.

 Delete marked Emails: You can delete all marks.

 E-mail accounts: You can create new account or

choose existing account.

 Template: you can pre-edit some common phrases,

which is convenient for quick editing.

Profile 1:

 Activate: You can activate the parameters set in

Mode 1.

 Edit: You can set menu function selection.

 Account Settings: You can set basic

transmission parameters, including

Account name, Data account, protocol,

check interval,Download size, Reply to

address.

 Outgoing Server: You can set the server

parameters for the sent e-mails, including

outward server, outgoing port, display

name and e-mail address etc.

 Incoming Server: You can set the server

parameters for the received e-mails,

including Incoming server, Incoming port,

user name and password etc.

 Signature: You c an set it On or Off and

edit the signature.

[Voice Mail Server ]

This is a kind of network s ervice, which c annot be used

until you apply to the network operator or open it. Please

consult the local service provider for more details and voice

mail number.  Edit: You can edit name and edit the voice mail

number. Press the OK key to save the number.

 Connect to Voice: You can dial the voice mail number

saved in the voice mail number function list. If you

have two phone numbers, they will have their own

voice mail number.

Tip: In standby state, after the voice mail number is set,

press 1 key to call the voice mail. In dual-SIM standby state,

you can choose to call the voice inbox via SIM1 or SIM2.

[Broadcast Message ]

Cell broadcast is a kind of information service s uch as

weather report, traffic etc that the network operator sends to

the GSM users within certain area. In dual-SIM mode, you

can separately set SIM1 and SIM2.

 Receive Mode: You can ON/OFF such function.  Read Message: You cannot read the received

information until you open such function.

 Languages: You can set the language for the received

information.

 Channel Settings: You can choose, add and edit and

delete channel number.

6.2 Call History

In dual-SIM mode, you can separately s earch the call

can set the available SIM card and see its call register.

Call history includes missed c alls, dialed calls and

received calls,delete call log,call time,call cost,SMS

counter,GPRS counter etc.

In missed calls, received calls and dialed calls function

list, you can see the date and time of the call, edit or delete

the phone number in the list, save the number to phonebook

or send SMS and MMS to the number, etc.

Note:SIM1 and SIM2 contains respectively 40 entries.

Choose any entry from missed calls, received calls and

dialed calls, press the Send key to dial the number directly.

Call time

 Last Call time: W ith this function, you can view the last

call time.

 Total Sent: With function, you can view the duration of all

dialed calls.

 Total Received: W ith the function, you can view the

duration of all received calls.

 Reset all time: W ith this function, you c an clear all

duration records of calls.

Note: The actual call duration and s ervice time in the bill of

the service provider may be different from them, which

depends on the network functions, accounting rounding and

tax etc.

Call Cost

This needs the support of the network service provider.  Last Call Cost: With this function, you can view the fees

of the last call.

 Total C ost: With this function, you can view the fees of

all calls.

 Reset Cost: With this function, you can clear all fee

records.

 Max Cost: W ith this function, you c an limit call fees in

the specified pricing unit or currency unit. PIN2 code

must be input to set call cost.

 Price Per Unit: This function needs network support. For

more details, please consult the network operator.

SMS Counter

With this function, you can see and preset the number of

sent messages and rec eived messages .

GPRS Counter

 Last Sent: You can view the sending traffic of last

link.

 Last Received: You can view the reception traffic of

last link.

 All Sent: You can view the sending traffic of all links.  All Received: You can view the reception traffic of all

links.

 Reset Counter: You can clear all link traffic.

6.3 Phonebook

The mobile phone is provided with the business card

folder type phonebook. The information of every contact

saved on the mobile phone include three phone numbers

(mobile phone, home phone and company phone), company

name, e-mail, f ax, birthday, big-head sticker, tone, callers’

group (five types: family, friends, VIPs, colleagues and

others). Every contact saved into SIM1 and SIM2 can only

include name and number. The mobile phone supports

1,000 groups of numbers.

[Quick Search ]

Input the initial Pinyin letter or English letter in the

position where the cursor is flickering to position the contact

from these contacts that meets the conditions, e.g. search

Zhang, input “z” in the input area, then you can find it.

[Search contact]

Input the name to be searched, press “Search” in the

phonebook, then you can find the matching name.

[Add New Contact]

You can save phone numbers onto SIM card or phone.

On SIM card, one entry has only name and phone number.

On the phone, one contact can include Name, Number,

Home Number, Company Name, E-mail Address, Office

Number, Fax Number, Birthday, Associate Picture,

Associate Sound and Caller Group.

Tip: If one contact is set with photo link, tone link and callers’

group at the same time, then the callers’ group function will

be inactive.

[Copy All ]

You can copy all contacts from SIM1 to phone, from

phone to SIM1, from SIM2 to phone, from phone to SIM2,

from SIM1 to SIM2 and from SIM2 to SIM1.

[Delete ]

You can have four modes regarding deletion: from

SIM1,from SIM2, from phone and one by one.

[Caller Groups]

You can set call tone, photo and members for five callers’

groups. Callers’ group member can only come from the

number saved on phone.

[Extra Number]

You can separately set SIM1 and SIM2’s My Caller ID,

service numbers and emergency numbers (the latter two

needs the support of the SIM card, consult the network

operator for details).

[Settings ]

 Memory Status: You can view the current use status of

the phonebook, including SIM1, SIM2 and phone

memory. The display format is “Used/Total”.

 Preferred Storage: You can choose the storage path for

the current number.

 Fields: You can choose the display items in the

phonebook and the display items in the Add Contact

interface.

 Name list filter: You c an choose to display the contacts

saved on SIM cards or Phone, or both.

 My vCard: You can edit and send my business card.  Vcard version:including vcard 2.1 and vcard 3.0

[Caller picture ]

You can set the call big-head sticker.

[Caller ring tone ]

You can set call tones.

6.4 Settings

[User Profiles]

Your mobile phone is provided with multiple profiles so

that you can customize some settings in different cases for

different events. Firstly, as per your personal hobby, have

individualized settings on profile and then activate it. You

can have such profiles as General, Meeting, Outdoor, Indoor,

Headset, Headset and Bluetooth.

The content can be edited at every profiles mode as

following:  Tone Setup: Include Incoming Call, power-on,

power-off, Message Tone and Key Tone.

 Volume: Set the volume of Ring and Key Tone.  Alert type: You can choose any one from Ring,

Vibration, Vibration then Ring as the current ring

mode.

 Ring Type: You can choose any one from single,

repeat and ascending as the current ring type.  Extra Tone: You can have on/off settings on Warning

Tone, Error Tone,camp on Tone and Call Connect

Tone so as to have corresponding tone tips.

 Answer Mode: You can choose whether to use any

key to answer.

After individualized settings, choose “Activate” in “Select” to

start profiles.

Note: After the headset is inserted into the mobile phone,

the mobile phone will automatically change into headset

profile. Unplug the heads et to return to the previous profile.

In standby state, press # key to switch to silence profile

and again to the previous profile.

[Dual SIM settings]

You can in any place and at any time set the dual-mode

mobile phone as the following modes according to your own

demand:

 Dual SIM open  Only SIM1 open  Only SIM2 open  Flight mode

[Phone Setup ]

In such menu, you can set phone language, standby

wallpaper, time etc.  Time and Date: W ith this function, you can set city,

time and date format and the time of specific place.

Set Home City: You can set different

cities.

Note: This option must be used together with auto update of

time and date. Auto update of time and data cannot be

conducted unless the network supports.

Set Time and Date: You can set the current time

and date.

Set Format: You c an set the display format for

time and date.

Note: If the battery is taken from the mobile phone or the

battery is used up for long time, when switching on the

mobile phone after reinstalling the battery or charging the

battery, you need to reset the time and date.

Special Note: In the area forbidding using mobile phone

(such as cabinet), you must c onfirm to inactivate this

function before entering this area so as to prevent accident.  Schedule Power on/off: You can set the time for

schedule Power on/off.

 Language: You c an choose the desired language for

phone display.

 Preferred Input Methods: You can set the input

methods of the mobile phone according to your

operation habit.

 Display c haracteristic: You can set standby menu

display as wallpaper, screen saver, power on display,

power off display, whether to display time and date

and owner number (if set in the phonebook), operator

name, missed calls and missed SMS.

 Greeting text: You can set the greeting text displayed

on the main screen.

 Shortcuts: Here, you can c hoose shortcut function

menu options; after specifying the shortcut functions

for the f our function keys, press the shortcut function

key to enter this menu.

 Dedicated key: You can have corresponding settings on

the up, down, left and right keys.

 Auto update of date and time: To set the mobile phone

to automatically update time and date according to the

current time zone, choose “Activate”. Auto update of

time and date will not affect the alarm clock, c alendar

or alarm clock memo setting time, which will be

subject to the time and date when created. However,

auto update of time and date may make some set

alarm clocks out of date.

 UART setup: With this option, you can choose the

access of PC software to SIM1 and SIM2.

 Misc. Settings: You can adjust the brightness and time

of LCD backlight.

[Call Setup]

 Caller ID: Including set by Network, hide ID and send

ID.  Set by Network: While having a call

conversation, you can s end my caller ID in the

form preset by the system.

 Hide ID: W hile having a call conversation, you

will not send my caller ID. If the system does not

support such function, call may fail.

 Send ID: While having a call conversation, you

can send my caller ID to the system.

Note: This function needs network support.

 Call Waiting: You can set this function On or Off. The

call hold and multi-party call cannot be active unless

this function is activated. This needs network support.

 Call Divert: This is a kind of network function, which

cannot be used unless you apply to the network

operator for it. W ith this function, you can divert calls

meeting he conditions to another number.

Name Description

Divert All Voice

Calls

Divert if

Unreachable

Divert if no W hen the mobile phone does not

The network will divert all voice

calls without conditions.

When the network cannot find

your mobile phone (switched-off

or out of the s ervice area), it will

divert the calls.

Answer answer the call, the network will

automatically divert it.

Divert if Busy

Divert All Data

Calls

Cancel All

Diverts

 Call Barring

 Outgoing Calls:

1. All Calls: You can bar all outgoing calls.

2. International Calls: You can bar international

3. International Calls Except To Home PLMN:

When you are on line, the

network will divert the call.

Network support needed.

Cancel all divert functions.

calls.

When abroad, you can dial the calls of the

current country and the original country (the

service providers allows to do so).

 Incoming Calls:

1. All Calls: You can bar all incoming calls.

2. W hen Roaming: You can bar all calls except

the calls of the local service area.

 Cancel All: You can c ancel call barring settings

and dial/receive calls normally.

 Change Barring Password: You can apply to the

network to change the password for call

barring.

 Line Switching: You can choose Line 1 or Line 2.  Closed User Group: This function needs network

support. Please consult the local operator for details.

Black list: You can add number into the blacklist, and also

you can set it as On or Off.

Auto Redial: You can set it as On or Off. After the first

automatic redial f ails, at most ten times can be available to

connect a phone number.

Speedy Dial: You can set whether to activate this function

and edit the related speed dialing numbers. If this function is

“Active”, then you dial any of the corresponding individual

keys (2-9) on the standby interface to dial the number

specified for this key.

IP Dial: You can set 3 IP calls. Only one IP call can be

effective on SIM1 or SIM2.

Background sound:

Select when making call: If setting it as on, during call,

there will be background music coming out. If setting it as off,

you can shield this function.

Playback Settings:You can set volume and continuous

play interval.

Effect List: There are 10 kinds of defaulted background

music such as motorcycle and walking on pavement etc.

More: there are three functions ,including the f ollowing:

 Call time Display: You can set whether to display

call duration during call conversation.

 Call Time Reminder: You can set one alert tone

or periodic alert tone for several round minutes

during c all conversation so that you can

understand call time. You can turn off the alert

tone.

 Auto quick end: You c an s et call duration. After

the set time expires, the mobile phone will

automatically end the call.

Note: Some settings need network support. For example,

call barring can not be used unless the local network and

SIM card open it.

[Network Setup]

In dual-SIM standby mode, you can separately set

SIM1 network and SIM2 network.

Network Selection: You can search the network again.

Select your f avorite network and choose to register the

network automatically or manually.

Preferred Networks: You can set the preferred

registered network for SIM card.

[Security Setup]

In dual-SIM standby mode, you can separately set the PIN

code, fixed dial and call barring of the SIM1 and SIM2.  SIM Security Setup: it include four parts,see it as

follow:  SIM Lock: You can set host SIM lock (PIN code

and PIN2 code) as on/off. W hen this option is

chosen, it is necessary to input PIN code for

every insert of the SIM card.

 Fixed Dial: This function needs the support of

the SIM card and the network operator. When it

is activated, you can only dial the phone

numbers saved in host fixed dial list. To activate

it, you need to input host PIN2 code.

 Barred Dial: You c an set barring all or some

dials. (SIM card support needed)

 Change Password

 Phone Lock: You can set it as On or Off. It is a

password of 4-8 digits and the defaulted one is 1122.

You can change it.

 Auto Keypad Lock: You can set it as On or Off. The

mobile phone has keypad lock function. W hen it lasts

certain time, the keypad will be locked, including such

options as Off, 5s, 30s, 60s and 5min.

 Change Password: You can change the defaulted

phone password “1122” into 4-8-digit number easy to

remember. If the phone lock is activated, when

switched on, the mobile phone will hint “Phone locked”.

To unlock it, you can input the phone lock password

and click OK.

[Restore Factory Settings]

You can restore the factory settings of the mobile phone.

The factory setting password is 1122.

6.5 File Manager

You can manage photos, MP3 and folders.

[Phone]-- The storage body is phone.

[Open]: You can open Audio, Images, Photos, My Music and

Video folders.

Received

Audio—Audio folder

 Play: You can play the selected content.

 Forward: You can send audio to Profiles, MMS, e-mail

and SMS.

 Details: You can see the date and size of the file.

 Rename: You can rename the folder.

 Copy: You can copy the file into Audio, Images, My

Music, Photos, Video or specified folders.

 Move: You can move the file into Images, My Music,

Photos, Video or specified folders.

 Delete: You can delete the current record.

 Delete All files: You can delete all records in all current

folders.

 Sort by: You can rank files as per name, type, time and

size or choose “None”.

Ebook

Images—Images Folder

 View: You can see the current image.

 Forward: You can send images to screen saver,

Switch-on Cartoon, Switch-off Cartoon, Phonebook,

MMS and SMS etc.

 Details: You can see the date and size of the file.

 Rename: You can rename the folder.

 Copy: You can copy the file into Audio, Images, My

Music, Photos, Video or specified folders.

 Move: You can move the file into Audio, My Music,

Images, Photos, Video or specified folders.

 Delete: You can delete the current record.

 Delete All files: You can delete all records in all current

folders.

 Sort by: You can rank files as per name, type, time and

size or choose “None”.

My Music—MP3 Folder

 Play: You can play the current MP3.

 Forward: You c an send music to Profiles, MMS and

SMS.

 Details: You can see the date and size of the file.

 Rename: You can rename the folder.

 Copy: You can copy the file into Audio, Images,

Photos, Video or specified folders.

 Move: You can move the file into Audio, Images,

Photos, Video or specified folders.

 Delete: You can delete the current record.

 Delete All files: You can delete all records in all current

folders.

 Sort by: You can rank files as per name, type, time and

size or choose “None”.

Photos—Photo Folder

 View: You can see the current photo.

 Edit: You can enter photo artist and edit the desired

photo.

 Forward: You can s end photos to screen saver,

Switch-on Cartoon, Switch-off Cartoon, Phonebook,

MMS, e-mail and SMS etc.

 Details: You can see the date and size of the file.

 Rename: You can rename the folder.

 Copy: You can copy the file into Audio, Images, My

Music, Photos, Video or specified folders.

 Move: You can move the file into Audio, My Music,

Images, Video or specified folders.

 Delete: You can delete the current record.

 Delete All files: You can delete all records in all current

folders.

 Sort by: You can rank files as per name, type, time and

size or choose “None”.

Video—Video Folder

 Play: You can play the current video.

 Forward: You can send videos to Phonebook, MMS,

e-mail, Switch-on Cartoon and Switch-off Cartoon.

 Details: You can see the date and size of the file.

 Rename: You can rename the folder.

 Copy: You can copy the file into Audio, Images, My

Music, Photos, Video or specified folders.

 Move: You can move the file into Audio, Images, My

Music, Photos or specified folders.

 Delete: You can delete the current record.

 Delete All files: You can delete all records in all current

folders.

 Sort by: You can rank files as per name, type, time and

size or choose “None”.

Create Folder: Under the root directory, you can create

a new folder to save more detailed files.

Format: Formatting can clear all files in the mobile

phone and newly created folders. After formatting, you need

to restart the mobile phone and the Audio folder and Images

folder will restore automatically and Photos f older will

automatically occur after the first photo is taken.

Memory Card

 Open: You can open the files in the memory card.  New Folder: Under the root directory, you can create a

new folder to save more detailed files.

 Format: You can format all files in the memory card.

Remove: You can remove the desired memory card

from the mobile phone safely.

6.6 Fun &Game

[Games]

This mobile phone provides some inbuilt games. Please

100

General mobile DST BUSINESS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual