SETUP & OPERATION MANUAL
FEATURES
2 HP DUST COLLECTOR
All single phase models are equipped with
totally enclosed, fan cooled, permanently
lubricated motors.
Heavy-duty motor design with a continuous duty rating for industrial applications.
Heavy-duty base,mounted on four swivel
casters for total mobility and stability.
Precision spin-balanced aluminum impeller for smooth operation,minimal noise
and to reduce the risk of sparking.
All models are equipped with 2 micron
filter bags. (Not included on “CF”canister
filter model)
Quick-release bag clamps with metal
straps on all models.
Safety switch with key, prevents unit from
being started when key is removed.
Heavy-duty collection bags made from
extra thick, transparent, recyclable plastic.
10-110CF M1
10-110 M1
SPECIFICATIONS
INLET DIAMETERS
(1) 6” (152 mm)
(2) 4” (102 mm)
AIRFLOW CAPACITY
1550 CFM
BLOWER WHEEL DIAMETER
12-3/4’’ (324 mm)
SOUND RATING
80 TO 90 dB
BAG DIAMETER
20’’ (508 mm)
BAG CAPACITY
42 GAL (190.9 L.)
STATIC PRESSURE
11-1/4” OF WATER
MOTOR
-
15A
#10-110
#10-110CF
#10-110
M1: 2 HP, 120 V, 1 Ph,
M3: 2 HP, 600 V, 3 Ph, 2.6 A
OVERALL DIMENSIONS (L x W x H)
39 3/8” x 31 1/2” x 74 3/4”
(1000 x 800 x 2000 mm) -
39 3/8” x 31 1/2” x 66 3/4”
(1000 x 800 x 1746 mm) -
WEIGHT
132 LBS (60 kg)
141 LBS (64 kg) - #10-110CF
MODEL
#10-110 M1
#10-110CF M1
VERSION 2_REVISION 2 - January 2019
© COPYRIGHT GENERAL INTERNATIONAL
GENERAL® INTERNATIONAL
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca
THANK YOU for choosing this General
®
International model 10-110/
10-110CF Dust collector. This dust collector has been carefully tested and inspected before
shipment and if properly used and maintained, will provide you with years of reliable service.
To ensure optimum performance and trouble-free operation, and to get the most from your
investment, please take the time to read this manual before assembling, installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and features
of this dust collector as well as the set-up, maintenance and identification of its parts and components. This manual is not intended as a substitute for formal woodworking instruction, nor
to offer the user instruction in the craft of woodworking. If you are not sure about the safety of
performing a certain operation or procedure, do not proceed until you can confirm, from
knowledgeable and qualified sources, that it is safe to do so.
Once you’ve read through these instructions, keep this manual handy for future reference.
GENERAL® INTERNATIONAL WARRANTY
All component parts of General® International machinery are carefully tested and inspected during all stages of
production, and each machine is thoroughly inspected upon completion of assembly. Because of our commitment to quality and customer satisfaction, General® International agrees to repair or replace, within a period of
24 months from date of purchase, any genuine part or parts which, upon examination, prove to be defective in
workmanship or material. In order to obtain this warranty, all defective parts must be returned freight pre-paid to
General® International Mfg. Co., Ltd. Repairs attempted without our written authorization will void this warranty.
Disclaimer: The information and specifications in this manual pertain
to the unit as it was supplied from the factory at the time of printing. Because we are committed to making constant improvements,
®
General
nents, parts or features of this unit as deemed necessary, without prior
notice and without obligation to install any such changes on previously
delivered units. Reasonable care is taken at the factory to ensure that
the specifications and information in this manual corresponds with that
of the unit with which it was supplied. However, special orders and
International reserves the right to make changes to compo-
“after factory” modifications may render some or all information in this
manual inapplicable to your machine. Further, as several generations
of this dust collector and several versions of this manual may be in circulation, if you own an earlier or later version of this unit, this manual may
not depict your machine exactly. If you have any doubts or questions
contact your retailer or our support line with the model and serial
number of your unit for clarification.
GENERAL
All component parts of General® International and Excalibur by General International ®
pro-ducts are carefully inspected during all stages of production and each unit is thoroughly
inspected upon completion of assembly.
Limited Lifetime Warranty
Because of our commitment to quality and customer satisfaction, General® International
agree to repair or replace any part or component which upon examination, proves to be
defective in either workmanship or material to the original purchaser for the life of the tool.
However, the Limited Lifetime Warranty does not cover any product used for professional or
commercial production purposes nor for industrial or educational applications. Such cases
are covered by our Standard 2-year Limited Warranty only. The Limited Lifetime Warranty is
also subject to the “Conditions and Exceptions” as listed below.
Standard 2-Year Limited Warranty
All products not covered by our lifetime warranty including products used in commercial,
industrial and educational applications are warranted for a period of 2 years (24 months)
from the date of purchase. General® International agrees to repair or replace any part or
component which upon examination, proves to be defective in either workmanship or material to the original purchaser during this 2-year warranty period, subject to the “conditions and
exceptions” as listed below.
INTERNATIONAL WARRANTY
®
To file a Claim
To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime
Warranty, all defective parts, components or machinery must be returned freight or postage
prepaid to General® International, or to a nearby distributor, repair center or other location
designated by General® International. For further details call our service department at 1-888949-1161 or your local distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof
of purchase and a “letter of claim” must be included (a warranty claim form can also be used
and can be obtained, upon request, from General® International or an authorized distributor)
clearly stating the model and serial number of the unit (if applicable) and including an explanation of the complaint or presumed defect in material or workmanship..
CONDITIONS AND EXCEPTIONS:
This coverage is extended to the original purchaser only. Prior warranty registration is not
required but documented proof of purchase i.e. a copy of original sales invoice or receipt
showing the date and location of the purchase as well as the purchase price paid, must be
provided at the time of claim.
Warranty does not include failures, breakage or defects deemed after inspection by
General® International to have been directly or indirectly caused by or resulting from; improper use, or lack of or improper maintenance, misuse or abuse, negligence, accidents, damage
in handling or transport, or normal wear and tear of any generally considered consumable
parts or components.
Repairs made without the written consent of General® Internationallwill void all warranty.
Rules for Safe Operation
To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and
holds itself harmless for any injury that may result from improper use of its equipment.
1. Do not operate this machine without either a filter
bag or canister filter properly installed on the unit.
2. Keep the work area well lit, clean and free of debris.
3. Do not handle the electrical plug with wet hands.
4. Do not use this unit outdoors or near wet surfaces.
5. Always turn on the dust collector before starting the
dust producing machine. Always turn off the dust pro ducing machine before turning off the dust collector.
6. Do not vacuum anything that is burning, smoking or
smoldering such as cigarettes, matches or hot ashes.
7. Stay alert! Give your work your undivided attention.
Even a momentary distraction can lead to serious
injury.
8. Fine particulate dust is a carcinogen that can be
haz- ardous to health. Work in well ventilated area and
wear eye, ear and respiratory protection devices.
9. Do not wear loose clothing, gloves, bracelets, neck laces, or other jewelry.
10. Do not vacuum or use this dust collector near flamma ble or combustible liquids, gases, gasoline or other
fuels, lighter fluid, cleaners, oil or solvent based paints,
natural gas, hydrogen or explosive dusts like coal dust,
magnesium dust, grain dust or gun powder.
11. Do not operate this dust collector when tired, distrac ted or under the effects of drugs, alcohol or any
medication that impairs reflexes or alertness.
12. Do not operate the unit until a dust hose is installed
onto the hose inlet.
13. Never leave the machine unattended while running or
with the power on.
14. To avoid health hazards from vapors or dusts, do not
vacuum toxic material.
15. Do not insert hands or fingers or any foreign objects
into ventilation inlet and outlet openings.
16. Childproof and tamper proof your shop and all
machinery with locks, master electrical switches and
switch keys to prevent unauthorized or unsupervised
use.
17. Keep children and visitors at a safe distance when the
unit is running. Do not permit them to use the machine.
18. Use only recommended accessories. Use of acces sories NOT recommended by General
may result in a risk of injury or damage to the
machine.
19. Make sure the unit is properly grounded. If equipped
with three-prong plug, it should be plugged into a
three-pole receptacle. Never remove the third-prong.
20. Always disconnect the unit from the power source
before servicing, performing any maintenance or
repairs and when changing bags or hoses, or if the
machine will be left unattended.
®
International
21. Do not use this dust collector for any purpose other
than it is intended use. If used for other purposes,
GENERAL® INTERNATIONAL disclaims any real or im plied warranty and holds itself harmless for any injury,
which may result from that use.
22. Clean filters (bags on 10-110 or canisters 10-110CF)
on a regular basis and replace as needed.
ELECTRICAL REQUIREMENTS
BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN
NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A
QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE.
THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.
Plug the dust collector into a proper receptacle. Your power tools should be connected to a dedicated electrical
circuit of not less than #14 wire and should be protected with a 15 amp time lag fuse. If an extension cord is needed
use only 3 wire cords with 3-prong grounded type plugs and 3-pole receptacles. Consult the chart below for details
on selecting an extension cord.
TABLE - MINIMUM GAUGE FOR CORD
AMPERE
RATING
MORE
THAN
0
6
10
12
NOT
MORE
THAN
6
10
12
16
BEFORE CONNECTING THE DUST COLLECTOR TO A POWER SOURCE, MAKE SURE THAT THE ELECTRICAL CURRENT
IS OF THE SAME TYPE AS THAT STAMPED ON THE MOTOR NAMEPLATE. ALL ELECTRICAL CONNECTIONS SHOULD
HAVE A PROPER CONTACT. NEVER CONNECT THE MACHINE TO A POWER SOURCE OF GREATER OR LOWER VOLTAGE THAN NEEDED. FAILURE TO COMPLY COULD RESULT IN SERIOUS INJURY TO THE USER AND/OR DAMAGE TO
THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE.
VOLTS
110 V
220 V
25 ft.
50 ft.
18
18
16
14
TOTAL LENGTH OF CORD IN FEET
50 ft.
100 ft.
AWG
16
16
16
12
GROUNDING
This dust collector must be grounded to protect the operator from electrical
shock. It has a 3-conductor cord and 3-prong grounded plug
ed-type receptacle
prong (grounding pin) from the plug to make it fit into an old 2 hole wall socket or extension cord. If an adaptor is used it must be attached to the metal
screw of the receptacle
. Do not attempt to modify the plug or remove the 3rd
.
to fit a ground-
100 ft.
200 ft.
16
14
14
-
150 ft.
300 ft.
14
12
12
-
Note: The use of an adaptor plug is illegal in some areas. Check your local
codes. If you have any doubts or if the supplied plug does not correspond
to your electrical outlet, consult a qualified electrician before proceeding.
5
2 HP DUST COLLECTOR
10-110 or 10-110CF
IDENTIFICATION OF MAIN PARTS AND COMPONENTS
OR
CONNECTOR
DRUM
COLLECTOR BODY W/MOTOR ASS’Y
BASE PLATE
HOSE INLET (“Y” FITTING)
6
FILTER BAG (10-110 ONLY)
CANISTER FILTER (10-110CF ONLY)
COLLECTOR BAG
BELT CLAMP (2X )
CASTER (4X)
UNPACKING AND PREPARATION FOR SETUP & ASSEMBLY
SAFETY
USE CAUTION AND WEAR GLOVES WHEN HANDLING METAL PARTS SUCH AS THE BELT CLAMPS,
WHICH CAN CUT IF HANDLED CARELESSLY.
DO NOT OVEREXERT. ARRANGE TO HAVE HELP
NEARBY AND READY FOR UNPACKING AND
SET- UP.
THE SOUND LEVEL OF THIS MACHINE IS RATED AT
APPROXIMATELY 80 TO 90 DB DURING OPERATION. MAKE SURE THAT ADEQUATE HEARING PROTECTION IS USED AND THAT THE OVERALL SOUND
LEVEL WITHIN THE WORKING ENVIRONMENT IS
TAKEN INTO CONSIDERATION.
ADDITIONAL REQUIREMENTS FOR SETUP & ASSEMBLY
• Flat piece of wood (such as a ruler)
• Medium phillips screwdriver
• 10 & 12 mm open end wrench or adjustable wrench
• 1 extra person for help with lifting
UNPACKING
Carefully unpack and remove the unit and its components from its shipping container and check for missing or
damaged items as per the list of contents below.
Note: Please report any damaged or missing items to your GENERAL® INTERNATIONAL distributor immediately.
LIST OF CONTENTS QTY
A- DRUM ........................................................................... 1
B- COLLECTOR BODY & MOTOR ASSEMBLY .................. 1
C- CONNECTOR ............................................................... 1
D- BASE PLATE ................................................................... 1
E- VERTICAL SUPPORT ROD ............................................. 1
F- FILTER BAG (10-110 ONLY) .......................................... 1
G- BAG HANGER (10-110 ONLY) ..................................... 1
H- COLLECTOR BAG ......................................................... 1
I- BELT CLAMP ................................................................. 2
LIST OF CONTENTS QTY
J- FOAM GASKET ............................................................. 1
K- RUBBER GASKET ........................................................... 2
L- HOSE INLET (“Y” FITTING)............................................. 1
M- CASTER ......................................................................... 4
N- HARDWARE BAG .......................................................... 1
WRENCH .................................................................................. 1
HEX. HEAD BOLT (5/16” X 1/2”) .......................................... 40
CROSS HEAD SCREW (3/16” X 3/8”) ..................................... 1
OPEN END WRENCH 10-12 MM ............................................. 1
O- CANISTER FILTER (10-110CF ONLY) ............................. 1
C
WITH 10-110CF
A
B
F
O
G
H
I
J
L
D
K
N
E
M
7
SHOP PLACEMENT / SPACE CONSIDERATIONS
Because each shop situation is unique, the following factors should be taken into consideration when determining
and before deciding on the ideal installation to best suit
your shop dust collection needs.
The unit should be installed as close to the dust source(s)
as possible.
The base of the unit is mounted on casters and as such
the dust collector can be moved from one location to
another within the shop if a permanent installation location is not practical or desired.
In all cases the unit should be installed on a flat, sturdy
and stable surface that is able to support the weight of the
unit and its contents, as well as the weight of the operator.
The casters should be blocked to prevent the unit from
moving when it is in use.
Consider the space requirements for the unit and its use when
deciding where to install your dust collector in your shop.
31 1/2”
66 3/4”
39 3/8”
31 1/2”
73 3/4”
39 3/8”
6”
The dust collector is equipped with
a 6” main hose inlet that is fitted with
a dual-inlet “Y” fitting allowing you to
4”
connect up to two 4” dust hoses.
LAYING OUT A PLAN FOR THE PIPING
For permanent installations it is advisable to map out a rough layout of your planned installation starting from the
dust collector out to all the machines that you wish to connect to the system. You may vary your layout to suit
your specific shop needs and may choose to use metal or plastic ducting, or flexible hose in any combination as
suited to your needs.
Note: To avoid accidents as well as damage to ducting or hoses, plan your installation with hoses and ducting
running along walls or mounted from above wherever possible. See the accompanying examples of non-recommended and recommended installations.
START
START
Wherever possible avoid running hoses and ducting
along the floor.
HOSES AND DUCTING RUNNING ALONG THE SHOP FLOOR BETWEEN MACHINERY CAN CAUSE USERS TO TRIP AND
LEAD TO SERIOUS INJURY.
8
Keep hoses and ducting safely mounted along the
walls.
ASSEMBLY INSTRUCTIONS
SERIOUS PERSONAL INJURY COULD OCCUR IF YOU CONNECT THE MACHINE TO THE POWER SOURCE BEFORE YOU
HAVE COMPLETED THE INSTALLATION AND ASSEMBLY STEPS. DO NOT CONNECT THE MACHINE TO THE POWER
SOURCE UNTIL INSTRUCTED TO DO SO.
STEP 1 - INSTALL THE CASTERS
Turn the base plate upside down and using the supplied wrench, attach the 4 casters.
STEP 3 - ATTACH THE CONNECTOR
STEP 2 - ATTACH COLLECTOR BODY W/ MOTOR ASSEMBLY
Turn the base plate back over (right side up) and place
the collector body with motor assembly on it lining up
the mounting holes.
STEP 4 - ATTACH THE DRUM
Place one of the rubber gaskets over the opening of
the collector body. Take the connector and proceed
by placing it over the same opening.
STEP 5 - MOUNT THE SUPPORT ROD TO THE BASE
A
B
Note: The vertical support rod has an angled end, A, to seat
over the lip of the base.
Attach the vertical support rods to the rear of the base
plate and to the drum, B.
Use the remaining rubber gasket and place it over the
opening of the connector. Take the drum and proceed
by placing it over the same opening.
STEP 6 - INSTALL THE HOSE INLET (“Y” FITTING)
C
Install the hose fitting (“Y” fitting) to the front of the collector body with a pan head screw C
.
9
STEP 7 - INSTALL THE COLLECTOR BAG
STEP 8 - INSTALL THE FILTER BAG ON THE DRUM ( #10-110 only)
D
E
Attach the collector bag by using the hooks on the unit
to hold it in place D. Use the belt clamp to attach the
bag to the lower portion of the drum E. Before tightening the clamp, make sure the metal strap is sitting in the
groove on the lower portion of the drum to create an
airtight seal between the drum and the bag.
USE CAUTION AND WEAR GLOVES WHEN HANDLING
METAL PARTS SUCH AS BELT CLAMPS, WHICH CAN CUT
IF HANDLED CARELESSLY.
F
G
H
If you have model 10-110CF (with canister filter) skip
ahead to step #9.
Fit the upper bag support into the holes on the drum
F
. Slip a belt clamp through the opening in the filter
bag until it comes out through the hole at the other
end G. Use the belt clamp to attach the filter bag to
the upper portion of the drum H. Before tightening
the clamp make sure the metal strap is sitting in the
groove on the upper portion of the drum to create an
airtight seal between the drum and the bag.
STEP 9 - FIT THE CANISTER FILTER ONTO THE DRUM
(#10-110CF ONLY)
I
If you have model 10-110 with filter bag skip ahead to step
#10.
Fit the canister filter onto the drum as shown and use
the belt clamp to hold the canister securely onto the
drum.
Tip/Hint: To seat the canister on the rim of the drum, run a
flat piece of wood (such as a ruler) between the drum and
the black apron on the bottom of the canister I.
STEP 10 - INSTALL THE FOAM GASKET
(IF NEEDED)
Basic assembly is now complete and your dust collector is ready to be put into service. Once the unit is
hooked up to an appropriate electrical connection,
turn on the unit and check for air leaks around the
bags or canister filter
leak, peel off the backing of the adhesive foam gasket
and stick it onto the drum, making sure the gasket is
sitting in the appropriate groove.
(model 10-110CF). If there is an air
10
OPERATING INSTRUCTIONS
ALWAYS TURN ON THE DUST COLLECTOR BEFORE STARTING YOUR DUST PRODUCING MACHINE AND ALWAYS STOP THE
DUST PRODUCING MACHINE BEFORE TURNING OFF THE DUST COLLECTOR.
BEFORE STARTING
1. To minimize airborne dust make sure that all hoses, fittings and clamps are secure and airtight.
2. For maximum system efficiency, make sure a cover is installed on any unused hose inlet openings.
3. Never operate the machine without the filter bag or cartridge and the collection bag properly installed.
THE SOUND LEVEL OF THIS MACHINE IS RATED AT APPROXIMATELY 80-90 DB DURING OPERATION. MAKE SURE THAT ADEQUATE
HEARING PROTECTION IS USED AND THAT THE OVERALL SOUND LEVEL WITHIN THE WORKING ENVIRONMENT IS TAKEN INTO
CONSIDERATION.
BASIC INSTRUCTIONS
The MODEL 10-110 & 10-110CF Dust Collector has been designed to capture, remove, and collect nonmetallic dust and wood dust around the workshop and from woodworking machinery.
ON/OFF SWITCH
The model 10-110 & 10-110CF is equipped with a simple
“rocker style” On/Off switch featuring a removable lock
out safety key.
To prevent unauthorized use or unintentional start-up,
remove the safety key and store it in a safe place whenever the dust collector is not in use.
To start the dust collector, insert the safety key and pull up
the switch. To stop the machine, push down on the power
switch.
MAKE SURE THE SWITCH IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD.
REMOVE THE SWITCH KEY WHENEVER THE DUST COLLECTOR IS NOT IN USE. PLACE IT IN A SAFE PLACE AND OUT OF
THE REACH OF CHILDREN.
POWER ON
POWER OFF
SAFETY KEY
(PREVENTS START-UP
WHEN REMOVED)
MAINTENANCE & SERVICING
MAKE SURE THE SWITCH IS IN THE «OFF» POSITION AND UNPLUG THE UNIT FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE.
This machine operates on 220 V single phase power (M1 model only); if you suspect any electrical problems call
a qualified electrician to do the verification of the electrical circuit or the machine. If you need further help with your
dust collector contact your General® International distributor or call our Technical Support at (514) 326-1161.
• All bearings are sealed and permanently lubricated. No further lubrication is needed.
• Periodically inspect all hardware, fittings and fasteners that may have loosened due to vibration - retighten
as needed.
• Keep the outside of the unit clean and wipe off excessive dust or dirt with a dry rag.
• Clean filters (
• Periodically inspect inside all pipes, fittings, blast gates, and connectors for accumulated dust build-up
or other obstructions and clean as needed. Remove sections and vacuum or manually remove debris as
needed.
• Check and if necessary replace all damaged parts or components.
• Do not operate with a damaged filter bag or canister - replace damaged filter immediately.
• Periodically inspect the power cord and plug for damage. If necessary replace the power cord and plug
at the first signs of visible damage.
• Use only recommended parts and accessories. The use of parts or accessories NOT recommended by
GENERAL® INTERNATIONAL may result in a risk of injury or damage to the machine.
bag on 10-110 or cartridge on 10-110CF) on a regular basis and replace as needed.
11
CLEANING OR REPLACING THE FILTER BAGS (10-110 only)
TURN THE SWITCH TO THE “OFF” POSITION AND UNPLUG THE UNIT FROM THE POWER
SOURCE BEFORE CLEANING OR REPLACING FILTER BAGS OR BEFORE PERFORMING ANY
MAINTENANCE.
Tip/Hint: To avoid potentially costly down-time, consider keeping a spare filter bag on-hand
and nearby for use if needed.
After a period of time, depending on the frequency of use, the filter bag may become
clogged and affect airflow as well the overall efficiency of the unit. Should you notice
a drop in the efficiency or performance of the unit, it may be a sign that it is time to
clean the filter bag. If so, proceed as follows:
1. Turn off and unplug the machine.
2. Unclip the belt clamp and remove the bag from the machine.
3. Clean the dust from inside the filter bag using a vacuum.
4. For extreme cases, after the initial cleaning with a vacuum, turn filter bag inside out
and vacuum a second time, laying the bag on a flat hard surface (such as a table
or workbench) and slowly passing the vacuum nozzle over the entire surface area.
5. Reinstall the bag and reattach the clamp.
Note: Filter bags can also be machine washed (gentle cycle only) in cold or warm water.
Do not use hot water or detergent. Make sure the bag has completely dried before reinstalling on the machine. Make sure
to remove the belt clamp from the bag before washing!
CLEANING OR REPLACING THE CANISTER FILTER (10-110CF only)
TURN THE SWITCH TO THE “OFF” POSITION AND UNPLUG THE UNIT FROM THE POWER
SOURCE BEFORE CLEANING OR REPLACING CANISTER FILTER OR BEFORE PERFORMING
ANY MAINTENANCE.
After a period of time depending on the frequency of use, the canister filter may
become clogged and affect airflow as well the overall efficiency of the unit. Should
you notice a drop in the efficiency or performance of the unit, it may be a sign that it
is time to clean the filters. If so, proceed as follows:
1. Turn off and unplug the machine.
2. For basic cleaning, simply rotate the handle on the canister several rotations. The
internal flap will rub against the corrugated inner filter and shake free any built up dust from inside the filter.
3. For a more thorough cleaning, after rotating the handle, unclip the belt clamps
and remove the canister from the machine and place it on the ground upside
down.
4. Vacuum the inside of the canister to remove any remaining dust from inside.
5. Re-install the canister and reattach the clamp.
CLEANING OR REPLACING THE COLLECTOR BAG
TURN THE SWITCH TO THE “OFF” POSITION AND UNPLUG THE UNIT FROM THE POWER SOURCE BEFORE CLEANING OR
REPLACING COLLECTOR BAG OR BEFORE PERFORMING ANY MAINTENANCE.
Note: Depending on your needs, shop situation and local regulations collections bags can be emptied and
reused or disposed (with their contents) and replaced with a new bag.
1. Turn off and unplug the machine.
2. Unclip the bag clamp and remove the bag from the machine.
3. Empty the bag (or simply dispose of the bag and its contents and replace with a new bag) disposing of the con-
tents in a safe and responsible manner that complies with all local codes and regulations regarding waste
disposal.
4. Re-install the bag and reattach the clamp.
12
RECOMMENDED OPTIONAL ACCESSORIES
We offer a large variety of products for increased convenience, productivity, accuracy and safety when
using your dust collector. Here’s a small sampling of optional accessories available from your local General
International dealer.
For more information about our products, please visit our website at www.general.ca
4” to 2 1/2” Reducer
#10-086
4” x 10’ Polyethylene
Flexible Hose
#10-410
1 Micron Canister Filter
#10-106C
4” x 50’ heavy-duty
polyethylene
flexible hose
#10-130
Clear Plastic
Collector Bag
#10-120
Window Type
Collector Bag
#10-125
Dust Collector Accessory
Kit Two Machine Hook-Up
#10-200
(2) 4” x 10’ Polyethylene flexible hose.
(1) 4” Universal dust hood outlet.
(1) Table saw dust hood.
(2) 4” blast gates
(1) 4”“Y” fitting.
(10) 4” wire bail hose clamps.
(6) Heavy duty clear plastic col-
lector bags.
2 Micron Filter Bag
#10-115
13
28
17A
25
30
12
18
2
11 A
10 A
9
6 A
13
5
29
4A
1
2
32
33
2
23
2
28
2
27
34
24
34
22
16
15
12
31
2
19
35
7A
26A
29A
3
6
14
PARTS LIST
10-110 & 10-110CF
NO PART N0. DESCRIPTION SPECIFICATION QTY
1 10110-01 CASTER 4
2 10110-02 HEX. HEAD BOLT 5/16” X 1/2” L 40
4A 10110-04A BASE PLATE 1
5 10110-05 PAN HEAD SCREW 3/16” X 3/8” L 12
6A 10110-06A INLET COVER 1
7A 10110-07A CAP SCREW M6 X 1.0 X 30 MM L.H. 1
9 10110-09 WASHER 1
10A 10110-10A FAN 1
11A 10110-11A COLLECTOR BODY 1
12 10110-12 WASHER 5/16” 8
13 10110-13 PAN HEAD SCREW 3/16” X 3/8” L 1
14 10110-14 HEX. HEAD BOLT 5/16” X 3/4” L 2
15 10110-15 HEX. HEAD BOLT 5/16” X 1” L 4
16 10110-16 SWITCH 1
17A 10110-17A MOTOR 1
18 10110-18 NUT 5/16” 4
19 10110-19 CONNECTOR 1
22 10110-22 COLLECTOR BAG (ITEM #10-120) 1
23 10110-23 VERTICAL SUPPORT ROD 1
24 10110-24 DRUM 1
25 10110-25 GASKET 1
26A 10110-26A HANGER* 1
27 10110-27 FILTER** 1
28 10110-28 FOAM GASKET 2
29 10110-29 HOSE INLET (“Y” FITTING) 1
29A 10110-29A CAP 1
30 10110-30 KEY 7MM X 7MM X 30MM 1
31 10110-31 POWER CORD 1
32 10110-32 OPEN END WRENCH 12MM 1
33 10110-33 HEX. WRENCH 5MM 1
34 10110-34 BELT CLAMP* (ITEM #10-093) 2
35 10110-35 FOAM GASKET 1
36 10110-36 LOCK WASHER 1/4” 1
*Not supplied/required for Model #10-110CF
**Filter bag #10-115 for model 10-110 or Canister filter #10-106C for model 10-110CF.
IMPORTANT: When ordering replacement parts, always give the model number, serial number of the
machine and part number. Also a brief description of each item and quantity desired.
Notes
15
Canister supplied
on Model 10-110CF
PART # DESCRIPTION SPEC. QTY
10106C-25 CANISTER FILTER DIA.500MM 1
10106C-26 NUT 5/16” 1
10106C-27 SET SCREW 5/16”X3/4” 1
10106C-28 HANDLE 1
10106C-29 HANDLE SPONGE 7/8” 1
10106C-30 CAP 3/4” 1
10106C-31 CANISTER FIXING PLATE 2
10106C-32 BEARING 1206 2
10106C-35 FLAPPER 3
10106C-36 SPINDLE 1
16
PARTS LIST
10-106C
PART # DESCRIPTION SPEC. QTY
10106C-38 ROUND HEAD SCREW M5X6 6
10106C-39 FIXING PLATE 2
10106C-40 BOTTOM FIXING PLATE 1
10106C-41 PHILLIPS HEAD SCREW M5X15 4
10106C-42 FOAM GASKET 3X20X1560 1
10106C-43 FOAM GASKET 5X42X1565 1
10106C-44 BELT CLAMP 500CK 1
10106C-58 FLANGE BOLT M5X12 8
10106C-59 NUT M5 6
10106C-60 FLAPPER BRACKET 1
Notes
17
MODEL 10-110 & 10-110CF
10-110CF
10-110
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Tel.: (514) 326-1161
Fax: (514) 326-5565 - Parts & Service / Fax: (514) 326-5555 - Order Desk
orderdesk@general.ca
www.general.ca
Follow us:
Loading...